Using int for values that are only used as booleans is confusing.
While at it, rearrange a couple of members so that all the bools
are contiguous.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It makes more sense to have ALL block size limit constraints
in the same struct. Improve the documentation while at it.
Simplify a couple of conditionals, now that we have audited and
documented that request_alignment is always non-zero.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_discard and
discard_alignment. Rename them, using 'pdiscard' as an aid to
track which remaining discard interfaces need conversion, and so
that the compiler will help us catch the change in semantics
across any rebased code. The BlockLimits type is now completely
byte-based; and in iscsi.c, sector_limits_lun2qemu() is no
longer needed.
pdiscard_alignment is made unsigned (we use power-of-2 alignments
as bitmasks, where unsigned is easier to think about) while
leaving max_pdiscard signed (since we still have an 'int'
interface); this is comparable to what commit cf081fc did for
write zeroes limits. We may later want to make everything an
unsigned 64-bit limit - but that requires a bigger code audit.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Improve the documentation of the write zeroes limits, to mention
additional constraints that drivers should observe. Worth squashing
into commit cf081fca, if that hadn't been pushed already :)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_transfer_length
and opt_transfer_length. Rename them (dropping the _length suffix)
so that the compiler will help us catch the change in semantics
across any rebased code, and improve the documentation. Use unsigned
values, so that we don't have to worry about negative values and
so that bit-twiddling is easier; however, we are still constrained
by 2^31 of signed int in most APIs.
When a value comes from an external source (iscsi and raw-posix),
sanitize the results to ensure that opt_transfer is a power of 2.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The NBD layer was breaking up request at a limit of 2040 sectors
(just under 1M) to cater to old qemu-nbd. But the server limit
was raised to 32M in commit 2d8214885 to match the kernel, more
than three years ago; and the upstream NBD Protocol is proposing
documentation that without any explicit communication to state
otherwise, a client should be able to safely assume that a 32M
transaction will work. It is time to rely on the larger sizing,
and any downstream distro that cares about maximum
interoperability to older qemu-nbd servers can just tweak the
value of #define NBD_MAX_SECTORS.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Block jobs that use additional BDSes or event loop resources need a
callback to get their affairs in order when the AioContext is switched.
Simple block jobs don't need an attach callback, they automatically work
thanks to the generic attach/detach notifiers that this patch adds.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466096189-6477-7-git-send-email-stefanha@redhat.com
It's possible that an AioContext notifier user was close to finishing
when .detach_aio_context() or .attached_aio_context() is called. In
that case they may call bdrv_remove_aio_context_notifier() during the
callback.
Use safe iteration to avoid crashing when the notifier list is modified
during iteration. We must not only handle the case where the current
aio notifier is removed during a callback but also the one where any
other aio notifier is removed.
The next patch adds an AioContext notifier for block jobs and they
really could be terminating just as .detach_aio_context() is invoked.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466096189-6477-6-git-send-email-stefanha@redhat.com
Block jobs are coroutines that usually perform I/O but sometimes also
sleep or yield. Currently only sleeping or yielded block jobs can be
paused. This means jobs that do not sleep or yield (using
block_job_yield()) are unaffected by block_job_pause().
Add block_job_pause_point() so that block jobs can mark quiescent points
that are suitable for pausing. This solves the problem that it can take
a block job a long time to pause if it is performing a long series of
I/O operations.
Transitioning to paused state involves a .pause()/.resume() callback.
These callbacks are used to ensure that I/O and event loop activity has
ceased while the job is at a pause point.
Note that this patch introduces a stricter pause state than previously.
The job->busy flag was incorrectly documented as a quiescent state
without I/O pending. This is violated by any job that has I/O pending
across sleep or block_job_yield(), like the mirror block job.
[Add missing block_job_should_pause() check to avoid deadlock after
job->driver->pause() in block_job_pause_point().
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466096189-6477-4-git-send-email-stefanha@redhat.com
The block_job_is_paused() function name is not great because callers
only use it to determine whether pausing has been requested. Rename it
to highlight those semantics and remove it from the public header file
as there are no external callers.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466096189-6477-3-git-send-email-stefanha@redhat.com
Declare a constant and use that when determining if an export
name fits within the constraints we are willing to support.
Note that upstream NBD recently documented that clients MUST
support export names of 256 bytes (not including trailing NUL),
and SHOULD support names up to 4096 bytes. 4096 is a bit big
(we would lose benefits of stack-allocation of a name array),
and we already have other limits in place (for example, qcow2
snapshot names are clamped around 1024). So for now, just
stick to the required minimum, as that's easier to audit than
a full-scale support for larger names.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1463006384-7734-12-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These structs are never used to represent the bytes that go over the
network. The big-endian network data is built into a uint8_t array
in nbd_{receive,send}_{request,reply}. Remove the unused magic field,
reorder the struct to avoid holes, and remove the packed attribute.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, we are trying to move the backing BDS from the source to the
target in bdrv_replace_in_backing_chain() which is called from
mirror_exit(). However, mirror_complete() already tries to open the
target's backing chain with a call to bdrv_open_backing_file().
First, we should only set the target's backing BDS once. Second, the
mirroring block job has a better idea of what to set it to than the
generic code in bdrv_replace_in_backing_chain() (in fact, the latter's
conditions on when to move the backing BDS from source to target are not
really correct).
Therefore, remove that code from bdrv_replace_in_backing_chain() and
leave it to mirror_complete().
Depending on what kind of mirroring is performed, we furthermore want to
use different strategies to open the target's backing chain:
- If blockdev-mirror is used, we can assume the user made sure that the
target already has the correct backing chain. In particular, we should
not try to open a backing file if the target does not have any yet.
- If drive-mirror with mode=absolute-paths is used, we can and should
reuse the already existing chain of nodes that the source BDS is in.
In case of sync=full, no backing BDS is required; with sync=top, we
just link the source's backing BDS to the target, and with sync=none,
we use the source BDS as the target's backing BDS.
We should not try to open these backing files anew because this would
lead to two BDSs existing per physical file in the backing chain, and
we would like to avoid such concurrent access.
- If drive-mirror with mode=existing is used, we have to use the
information provided in the physical image file which means opening
the target's backing chain completely anew, just as it has been done
already.
If the target's backing chain shares images with the source, this may
lead to multiple BDSs per physical image file. But since we cannot
reliably ascertain this case, there is nothing we can do about it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20160610185750.30956-3-mreitz@redhat.com
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
It is always true for open images now.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This allows drivers to share code between normal I/O and vmstate
accesses.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This brings it in line with .bdrv_save_vmstate().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
We already have a byte-based bdrv_pwritev(), but the read counterpart
was still missing. This commit adds it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
In a first step to convert the common I/O path to work on bytes rather
than sectors, this converts the copy-on-read logic that is used by
bdrv_aligned_preadv().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a new BDRV_REQ_MASK constant, and use it to make sure that
caller flags are always valid.
Tested with 'make check' and with qemu-iotests on both '-raw'
and '-qcow2'; the only failure turned up was fixed in the
previous commit.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that all drivers have been converted to a byte interface,
we no longer need a sector interface.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Rename to bdrv_pwrite_zeroes() to let the compiler ensure we
cater to the updated semantics. Do the same for bdrv_co_write_zeroes().
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Update bdrv_co_do_write_zeroes() to be byte-based, and select
between the new byte-based bdrv_co_pwrite_zeroes() or the old
bdrv_co_write_zeroes(). The next patches will convert drivers,
then remove the old interface.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Another step towards removing sector-based interfaces: convert
the maximum write and minimum alignment values from sectors to
bytes. Rename the variables to let the compiler check that all
users are converted to the new semantics.
The maximum remains an int as long as BDRV_REQUEST_MAX_SECTORS
is constrained by INT_MAX (this means that we can't even
support a 2G write_zeroes, but just under it) - changing
operation lengths to unsigned or to 64-bits is a much bigger
audit, and debatable if we even want to do it (since at the
core, a 32-bit platform will still have ssize_t as its
underlying limit on write()).
Meanwhile, alignment is changed to 'uint32_t', since it makes no
sense to have an alignment larger than the maximum write, and
less painful to use an unsigned type with well-defined behavior
in bit operations than to have to worry about what happens if
a driver mistakenly supplies a negative alignment.
Add an assert that no one was trying to use sectors to get a
write zeroes larger than 2G, and therefore that a later conversion
to bytes won't be impacted by keeping the limit at 32 bits.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I was thrown by the fact that the public type BlockRequest had
an anonymous union, but no obvious discriminator. Turns out
that the only client of the second branch of the union was code
internal to io.c, now that commit 91c6e4b killed public
multiwrite, so move it into io.c and improve the comments.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1463699150-19445-1-git-send-email-eblake@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
There is a single remaining user in qemu-img, and another one in a test
case, both of which can be trivially converted to using BlockJob.blk
instead.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This changes the backup block job to use the job's BlockBackend for
performing its I/O. job->bs isn't used by the backup code any more
afterwards.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This changes the streaming block job to use the job's BlockBackend for
performing the COR reads. job->bs isn't used by the streaming code any
more afterwards.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This adds a new BlockBackend field to the BlockJob struct, which
coexists with the BlockDriverState while converting the individual jobs.
When creating a block job, a new BlockBackend is created on top of the
given BlockDriverState, and it is destroyed when the BlockJob ends. The
reference to the BDS is now held by the BlockBackend instead of calling
bdrv_ref/unref manually.
We have to be careful when we use bdrv_replace_in_backing_chain() in
block jobs because this changes the BDS that job->blk points to. At the
moment block jobs are too tightly coupled with their BDS, so that moving
a job to another BDS isn't easily possible; therefore, we need to just
manually undo this change afterwards.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
So far, bdrv_close_all() first removed all root BlockDriverStates of
BlockBackends and monitor owned BDSes, and then assumed that the
remaining BDSes must be related to jobs and cancelled these jobs.
This order doesn't work that well any more when block jobs use
BlockBackends internally because then they will lose their BDS before
being cancelled.
This patch changes bdrv_close_all() to first cancel all jobs and then
remove all root BDSes from the remaining BBs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The current way to obtain the list of existing block jobs is to
iterate over all root nodes and check which ones own a job.
Since we want to be able to support block jobs in other nodes as well,
this patch keeps a list of jobs that is updated every time one is
created or destroyed.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
When changing the BlockDriverState that a BdrvChild points to while the
node is currently drained, we must call the .drained_end() parent
callback. Conversely, when this means attaching a new node that is
already drained, we need to call .drained_begin().
bdrv_root_attach_child() takes now an opaque parameter, which is needed
because the callbacks must also be called if we're attaching a new child
to the BlockBackend when the root node is already drained, and they need
a way to identify the BlockBackend. Previously, child->opaque was set
too late and the callbacks would still see it as NULL.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
There are no callers to bdrv_open() or bdrv_open_inherit() left that
pass a pointer to a non-NULL BDS pointer as the first argument of these
functions, so we can finally drop that parameter and just make them
return the new BDS.
Generally, the following pattern is applied:
bs = NULL;
ret = bdrv_open(&bs, ..., &local_err);
if (ret < 0) {
error_propagate(errp, local_err);
...
}
by
bs = bdrv_open(..., errp);
if (!bs) {
ret = -EINVAL;
...
}
Of course, there are only a few instances where the pattern is really
pure.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is unused now, so we may just as well drop it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bdrv_next() users all leaked the BdrvNextIterator after completing
the iteration. Simply changing bdrv_next() to free the iterator before
returning NULL at the end of list doesn't work because some callers exit
the loop before looking at all BDSes.
This patch moves the BdrvNextIterator from the heap to the stack of
the caller and switches to a bdrv_first()/bdrv_next() interface for
initialising the iterator.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
This patch removes the remaining users of bs->blk, which will allow us
to have multiple BBs on top of a single BDS. In the meantime, all checks
that are currently in place to prevent the user from creating such
setups can be switched to bdrv_has_blk() instead of accessing BDS.blk.
Future patches can allow them and e.g. enable users to mirror to a block
device that already has a BlockBackend on it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We need to introduce a separate BdrvNextIterator struct that can keep
more state than just the current BDS in order to avoid using the bs->blk
pointer.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Since virtio-blk implements request merging itself these days, the only
remaining users are test cases for the function. That doesn't make the
function exactly useful any more.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
When block job errors were introduced, we assigned the iostatus of the
target BDS "just in case". The field has never been accessible for the
user because the target isn't listed in query-block.
Before we can allow the user to have a second BlockBackend on the
target, we need to clean this up. If anything, we would want to set the
iostatus for the internal BB of the job (which we can always do later),
but certainly not for a separate BB which the job doesn't even use.
As a nice side effect, this gets us rid of another bs->blk use.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to get rid of bs->blk for bdrv_get_device_name() and
bdrv_get_device_or_node_name(), ask all parents for their name and
simply pick the first one.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We want to get rid of BlockDriverState.blk in order to allow multiple
BlockBackends per BDS. Converting the device callbacks in block.c (which
assume a single BlockBackend) to per-child callbacks gets us rid of the
first few instances.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This moves the throttling related part of the BDS life cycle management
to BlockBackend. The throttling group reference is now kept even when no
medium is inserted.
With this commit, throttling isn't disabled and then re-enabled any more
during graph reconfiguration. This fixes the temporary breakage of I/O
throttling when used with live snapshots or block jobs that manipulate
the graph.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This removes the last part of I/O throttling from block/io.c and moves
it to the BlockBackend.
Instead of having knowledge about throttling inside io.c, we can call a
BdrvChild callback .drained_begin/end, which happens to drain the
throttled requests for BlockBackend parents.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
BlockBackends use it to get a back pointer from BdrvChild to
BlockBackend in any BdrvChildRole callbacks.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch changes where the throttling state is stored (used to be the
BlockDriverState, now it is the BlockBackend), but it doesn't actually
make it a BB level feature yet. For example, throttling is still
disabled when the BDS is detached from the BB.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
As a first step towards moving I/O throttling to the BlockBackend level,
this patch changes all pointers in struct ThrottleGroup from referencing
a BlockDriverState to referencing a BlockBackend.
This change is valid because we made sure that throttling can only be
enabled on BDSes which have a BB attached.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
In some cases, we want to take a quorum child offline, and take
another child online.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Changlong Xie <xiecl.fnst@cn.fujitsu.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1462865799-19402-2-git-send-email-xiecl.fnst@cn.fujitsu.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The block layer has a couple of cases where it can lose
Force Unit Access semantics when writing a large block of
zeroes, such that the request returns before the zeroes
have been guaranteed to land on underlying media.
SCSI does not support FUA during WRITESAME(10/16); FUA is only
supported if it falls back to WRITE(10/16). But where the
underlying device is new enough to not need a fallback, it
means that any upper layer request with FUA semantics was
silently ignoring BDRV_REQ_FUA.
Conversely, NBD has situations where it can support FUA but not
ZERO_WRITE; when that happens, the generic block layer fallback
to bdrv_driver_pwritev() (or the older bdrv_co_writev() in qemu
2.6) was losing the FUA flag.
The problem of losing flags unrelated to ZERO_WRITE has been
latent in bdrv_co_do_write_zeroes() since commit aa7bfbff, but
back then, it did not matter because there was no FUA flag. It
became observable when commit 93f5e6d8 paved the way for flags
that can impact correctness, when we should have been using
bdrv_co_writev_flags() with modified flags. Compare to commit
9eeb6dd, which got flag manipulation right in
bdrv_co_do_zero_pwritev().
Symptoms: I tested with qemu-io with default writethrough cache
(which is supposed to use FUA semantics on every write), and
targetted an NBD client connected to a server that intentionally
did not advertise NBD_FLAG_SEND_FUA. When doing 'write 0 512',
the NBD client sent two operations (NBD_CMD_WRITE then
NBD_CMD_FLUSH) to get the fallback FUA semantics; but when doing
'write -z 0 512', the NBD client sent only NBD_CMD_WRITE.
The fix is do to a cleanup bdrv_co_flush() at the end of the
operation if any step in the middle relied on a BDS that does
not natively support FUA for that step (note that we don't
need to flush after every operation, if the operation is broken
into chunks based on bounce-buffer sizing). Each BDS gains a
new flag .supported_zero_flags, which parallels the use of
.supported_write_flags but only when accessing a zero write
operation (the flags MUST be different, because of SCSI having
different semantics based on WRITE vs. WRITESAME; and also
because BDRV_REQ_MAY_UNMAP only makes sense on zero writes).
Also fix some documentation to describe -ENOTSUP semantics,
particularly since iscsi depends on those semantics.
Down the road, we may want to add a driver where its
.bdrv_co_pwritev() honors all three of BDRV_REQ_FUA,
BDRV_REQ_ZERO_WRITE, and BDRV_REQ_MAY_UNMAP, and advertise
this via bs->supported_write_flags for blocks opened by that
driver; such a driver should NOT supply .bdrv_co_write_zeroes
nor .supported_zero_flags. But none of the drivers touched
in this patch want to do that (the act of writing zeroes is
different enough from normal writes to deserve a second
callback).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pre-patch, .supported_write_flags lives at the driver level, which
means we are blindly declaring that all block devices using a
given driver will either equally support FUA, or that we need a
fallback at the block layer. But there are drivers where FUA
support is a per-block decision: the NBD block driver is dependent
on the remote server advertising NBD_FLAG_SEND_FUA (and has
fallback code to duplicate the flush that the block layer would do
if NBD had not set .supported_write_flags); and the iscsi block
driver is dependent on the mode sense bits advertised by the
underlying device (and is currently silently ignoring FUA requests
if the underlying device does not support FUA).
The fix is to make supported flags as a per-BDS option, set during
.bdrv_open(). This patch moves the variable and fixes NBD and iscsi
to set it only conditionally; later patches will then further
simplify the NBD driver to quit duplicating work done at the block
layer, as well as tackle the fact that SCSI does not support FUA
semantics on WRITESAME(10/16) but only on WRITE(10/16).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Vmdk images have metadata to indicate the vmware virtual
hardware version image was created/tested to run with.
Allow users to specify that version via new 'hwversion'
option.
[ kwolf: Adjust qemu-iotests common.filter ]
Signed-off-by: Janne Karhunen <Janne.Karhunen@gmail.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are no block drivers left that implement the old .bdrv_read/write
interface, so it can be removed now. This gets us rid of the
corresponding emulation functions, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Many parts of the block layer are already byte granularity. The block
driver interface, however, was still missing an interface that allows
making use of this. This patch introduces a new BlockDriver interface,
which is based on coroutines, vectored, has flags and uses a byte
granularity. This is now the preferred interface for new drivers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
It used to be an internal helper function just for implementing
bdrv_co_do_readv/writev(), but now that it's a public interface, it
deserves a name without "do" in it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Extract the handling of io_plug "depth" from linux-aio.c and let the
main bdrv_drain loop do nothing but wait on I/O.
Like the two newly introduced functions, bdrv_io_plug and bdrv_io_unplug
now operate on all children. The visit order is now symmetrical between
plug and unplug, making it possible for formats to implement plug/unplug.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extract the handling of throttling from bdrv_flush_io_queue. These
new functions will soon become BdrvChildRole callbacks, as they can
be generalized to "beginning of drain" and "end of drain".
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We want to remove throttled_reqs from block/io.c. This is the easy
part---hide the handling of throttled_reqs during disable/enable of
throttling within throttle-groups.c.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Using the nested aio_poll() in coroutine is a bad idea. This patch
replaces the aio_poll loop in bdrv_drain with a BH, if called in
coroutine.
For example, the bdrv_drain() in mirror.c can hang when a guest issued
request is pending on it in qemu_co_mutex_lock().
Mirror coroutine in this case has just finished a request, and the block
job is about to complete. It calls bdrv_drain() which waits for the
other coroutine to complete. The other coroutine is a scsi-disk request.
The deadlock happens when the latter is in turn pending on the former to
yield/terminate, in qemu_co_mutex_lock(). The state flow is as below
(assuming a qcow2 image):
mirror coroutine scsi-disk coroutine
-------------------------------------------------------------
do last write
qcow2:qemu_co_mutex_lock()
...
scsi disk read
tracked request begin
qcow2:qemu_co_mutex_lock.enter
qcow2:qemu_co_mutex_unlock()
bdrv_drain
while (has tracked request)
aio_poll()
In the scsi-disk coroutine, the qemu_co_mutex_lock() will never return
because the mirror coroutine is blocked in the aio_poll(blocking=true).
With this patch, the added qemu_coroutine_yield() allows the scsi-disk
coroutine to make progress as expected:
mirror coroutine scsi-disk coroutine
-------------------------------------------------------------
do last write
qcow2:qemu_co_mutex_lock()
...
scsi disk read
tracked request begin
qcow2:qemu_co_mutex_lock.enter
qcow2:qemu_co_mutex_unlock()
bdrv_drain.enter
> schedule BH
> qemu_coroutine_yield()
> qcow2:qemu_co_mutex_lock.return
> ...
tracked request end
...
(resumed from BH callback)
bdrv_drain.return
...
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1459855253-5378-2-git-send-email-famz@redhat.com
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The only remaining users were block jobs (mirror and backup) which
unconditionally enabled WCE on the BlockBackend of the target image. As
these block jobs don't go through BlockBackend for their I/O requests,
they aren't affected by this setting anyway but always get a writeback
mode, so that call can be removed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The previous patches have successively made blk->enable_write_cache the
true source for the information whether a writethrough mode must be
implemented. The corresponding BDRV_O_CACHE_WB is only useless baggage
we're carrying around, so now's the time to remove it.
At the same time, we remove the 'cache.writeback' option parsing on the
BDS level as the only effect was setting the BDRV_O_CACHE_WB flag.
This change requires test cases that explicitly enabled the option to
drop it. Other than that and the change of the error message when
writethrough is enabled on the BDS level (from "Can't set writethrough
mode" to "doesn't support the option"), there should be no change in
behaviour.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This function will allow drivers to implement BDRV_REQ_FUA natively
instead of sending a separate flush after the write.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Now that WCE is handled on the BlockBackend level, the flag is
meaningless for BDSes. As the schema requires us to fill the field,
we return an enabled write cache for them.
Note that this means that querying the BlockBackend name may return
writethrough as the cache information, whereas querying the node-name of
the root of that same BlockBackend will return writeback.
This may appear odd at first, but it actually makes sense because it
correctly repesents the layer that implements the WCE handling. This
becomes more apparent when you consider nodes that are the root node of
multiple BlockBackends, where each BB can have its own WCE setting.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Whether a write cache is used or not is a decision that concerns the
user (e.g. the guest device) rather than the backend. It was already
logically part of the BB level as bdrv_move_feature_fields() always kept
it on top of the BDS tree; with this patch, the core of it (the actual
flag and the additional flushes) is also implemented there.
Direct callers of bdrv_open() must pass BDRV_O_CACHE_WB now if bs
doesn't have a BlockBackend attached.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
It's like bdrv_parse_cache_flags(), except that writethrough mode isn't
included in the flags, but returned as a separate bool.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This patch adds callback for flush request. This callback is responsible
for flushing whole block devices stack. bdrv_flush function does not
proceed to underlying devices. It should be performed by this callback
function, if needed.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For a couple of releases we have been warning
Encrypted images are deprecated
Support for them will be removed in a future release.
You can use 'qemu-img convert' to convert your image to an unencrypted one.
This warning was issued by system emulators, qemu-img, qemu-nbd
and qemu-io. Such a broad warning was issued because the original
intention was to rip out all the code for dealing with encryption
inside the QEMU block layer APIs.
The new block encryption framework used for the LUKS driver does
not rely on the unloved block layer API for encryption keys,
instead using the QOM 'secret' object type. It is thus no longer
appropriate to warn about encryption unconditionally.
When the qcow/qcow2 drivers are converted to use the new encryption
framework too, it will be practical to keep AES-CBC support present
for use in qemu-img, qemu-io & qemu-nbd to allow for interoperability
with older QEMU versions and liberation of data from existing encrypted
qcow2 files.
This change moves the warning out of the generic block code and
into the qcow/qcow2 drivers. Further, the warning is set to only
appear when running the system emulators, since qemu-img, qemu-io,
qemu-nbd are expected to support qcow2 encryption long term now that
the maint burden has been eliminated.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When opening an image it is useful to know whether the caller
intends to perform I/O on the image or not. In the case of
encrypted images this will allow the block driver to avoid
having to prompt for decryption keys when we merely want to
query header metadata about the image. eg qemu-img info
This flag is enforced at the top level only, since even if
we don't want todo I/O on the 'qcow2' file payload, the
underlying 'file' driver will still need todo I/O to read
the qcow2 header, for example.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The function is unused since commit f21d96d0 ('block: Use BdrvChild in
BlockBackend').
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The call in hmp_drive_del() is dead code because blk_remove_bs() is
called a few lines above. The only other remaining user is
bdrv_delete(), which only abuses bdrv_make_anon() to remove it from the
named nodes list. This path inlines the list entry removal into
bdrv_delete() and removes bdrv_make_anon().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
qemu-common.h should only be included by .c files. Its file comment
explains why: "No header file should depend on qemu-common.h, as this
would easily lead to circular header dependencies."
qemu/iov.h includes qemu-common.h for QEMUIOVector stuff. Move all
that to qemu/iov.h and drop the ill-advised include. Include
qemu/iov.h where the QEMUIOVector stuff is now missing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-run scripts/clean-includes to apply the previous commit's
corrections and updates. Besides redundant qemu/typedefs.h, this only
finds a redundant config-host.h include in ui/egl-helpers.c. No idea
how that escaped the previous runs.
Some manual whitespace trimming around dropped includes squashed in.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces blk_co_preadv() as a central function on the
BlockBackend level that is supposed to handle all read requests from the
BB to its root BDS eventually.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a function for iterating over all monitor-owned BlockDriverStates so
the generic block layer can do so.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move bdrv_commit_all() and bdrv_flush_all() to the BlockBackend level.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only code change is making bdrv_dirty_bitmap_truncate public. It is
used in block.c.
Also two long lines (bdrv_get_dirty) are wrapped.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1457412306-18940-5-git-send-email-famz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Following patches to refactor and move block dirty bitmap code could use
this.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1457412306-18940-4-git-send-email-famz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch adds an option to the drive_add HMP command to create only a
BlockDriverState without a BlockBackend on top.
The motivation for this is that libvirt needs to specify options to a
migration target (specifically, detect-zeroes). drive-mirror doesn't
allow specifying options, and the proper way to do this is to create the
target BDS separately with blockdev-add (where you can specify options)
and then use blockdev-mirror to that BDS.
However, libvirt can't use blockdev-add as long as it is still
experimental, and we're expecting that it will still take some time, so
we need to resort to drive_add.
The problem with drive_add is that so far it always created a BB, and
BDSes with a BB can't be used as a mirroring target as long as we don't
support multiple BBs per BDS - and while we're working towards that
goal, it's another thing that will still take some time.
So to achieve the goal, the simplest solution to provide the
functionality now without adding one-off options to the mirror QMP
commands is to extend drive_add to create nodes without BBs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since commit 91a097e, we end up with a somewhat weird cache mode
configuration with snapshot=on: The commit broke the cache mode
inheritance for the snapshot overlay so that it is opened as
writethrough instead of unsafe now. The following bdrv_append() call to
put it on top of the tree swaps the WCE flag with the snapshot's backing
file (i.e. the originally given file), so what we eventually get is
cache=writeback on the temporary overlay and
cache=writethrough,cache.no-flush=on on the real image file.
This patch changes things so that the temporary overlay gets
cache=unsafe again like it used to, and the real images get whatever the
user specified. This means that cache.direct is now respected even with
snapshot=on, and in the case of committing changes, the final flush is
no longer ignored except explicitly requested by the user.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
NB: If this commit breaks compilation for your out-of-tree
patchseries or fork, then you need to make sure you add
#include "qemu/osdep.h" to any new .c files that you have.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
This extends the NBD protocol handling code so that it is capable
of negotiating TLS support during the connection setup. This involves
requesting the STARTTLS protocol option before any other NBD options.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-14-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all callers are converted to use I/O channels for
initial connection setup, it is possible to switch the core
NBD protocol handling core over to use QIOChannel APIs for
actual sockets I/O.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-7-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With a mirror job running on a virtio-blk dataplane disk, sending "q" to
HMP will cause a dead loop in block_job_finish_sync.
This is because the aio_poll() only processes the AIO context of bs
which has no more work to do, while the main loop BH that is scheduled
for setting the job->completed flag is never processed.
Fix this by adding a flag in BlockJob structure, to track which context
to poll for the block job to make progress. Its value is set to true
when block_job_coroutine_complete() is called, and is checked in
block_job_finish_sync to determine which context to poll.
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1454379144-29807-1-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This fixes a regression introduced with commit 3f09bfbc7. Multiple
bugs arise in conjunction with live snapshots and mirroring operations
(which include active layer commit).
After a live snapshot occurs, the active layer and the base layer both
have a non-NULL tqe_prev field in the device_list, although the base
node's tqe_prev field points to a NULL entry. This non-NULL tqe_prev
field occurs after the bdrv_append() in the external snapshot calls
change_parent_backing_link().
In change_parent_backing_link(), when the previous active layer is
removed from device_list, the device_list.tqe_prev pointer is not
set to NULL.
The operating scheme in the block layer is to indicate that a BDS belongs
in the bdrv_states device_list iff the device_list.tqe_prev pointer
is non-NULL.
This patch does two things:
1.) Introduces a new block layer helper bdrv_device_remove() to remove a
BDS from the device_list, and
2.) uses that new API, which also fixes the regression once used in
change_parent_backing_link().
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: 0cd51e11c0666c04ddb7c05293fe94afeb551e89.1454376655.git.jcody@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The added parameter can be used to return the BDS pointer which the
valid offset is referring to. Its value should be ignored unless
BDRV_BLOCK_OFFSET_VALID in ret is set.
Until block drivers fill in the right value, let's clear it explicitly
right before calling .bdrv_get_block_status.
The "bs->file" condition in bdrv_co_get_block_status is kept now to keep iotest
case 102 passing, and will be fixed once all drivers return the right file
pointer.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1453780743-16806-2-git-send-email-famz@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
As a side effect, we can now make x-blockdev-del's check whether a BDS
is actually owned by the monitor explicit.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
