qemu_rdma_accept() returns 0 in some cases even when it didn't
complete its job due to errors. Impact is not obvious. I figure the
caller will soon fail again with a misleading error message.
Fix it to return -1 on any failure.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-10-armbru@redhat.com>
qemu_rdma_exchange_get_response() compares int parameter @expecting
with uint32_t head->type. Actual arguments are non-negative
enumeration constants, RDMAControlHeader uint32_t member type, or
qemu_rdma_exchange_recv() int parameter expecting. Actual arguments
for the latter are non-negative enumeration constants. Change both
parameters to uint32_t.
In qio_channel_rdma_readv(), loop control variable @i is ssize_t, and
counts from 0 up to @niov, which is size_t. Change @i to size_t.
While there, make qio_channel_rdma_readv() and
qio_channel_rdma_writev() more consistent: change the former's @done
to ssize_t, and delete the latter's useless initialization of @len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-8-armbru@redhat.com>
qio_channel_rdma_readv() assigns the size_t value of qemu_rdma_fill()
to an int variable before it adds it to @done / subtracts it from
@want, both size_t. Truncation when qemu_rdma_fill() copies more than
INT_MAX bytes. Seems vanishingly unlikely, but needs fixing all the
same.
Fixes: 6ddd2d76ca (migration: convert RDMA to use QIOChannel interface)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-7-armbru@redhat.com>
We use int instead of uint64_t in a few places. Change them to
uint64_t.
This cleans up a comparison of signed qemu_rdma_block_for_wrid()
parameter @wrid_requested with unsigned @wr_id. Harmless, because the
actual arguments are non-negative enumeration constants.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-6-armbru@redhat.com>
wrid_desc[] uses 4001 pointers to map four integer values to strings.
print_wrid() accesses wrid_desc[] out of bounds when passed a negative
argument. It returns null for values 2..1999 and 2001..3999.
qemu_rdma_poll() and qemu_rdma_block_for_wrid() print wrid_desc[wr_id]
and passes print_wrid(wr_id) to tracepoints. Could conceivably crash
trying to format a null string. I believe access out of bounds is not
possible.
Not worth cleaning up. Dumb down to show just numeric wr_id.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-5-armbru@redhat.com>
rdma_delete_block() always returns 0, which its only caller ignores.
Return void instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-4-armbru@redhat.com>
qemu_rdma_data_init() return type is void *. It actually returns
RDMAContext *, and all its callers assign the value to an
RDMAContext *. Unclean.
Return RDMAContext * instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-3-armbru@redhat.com>
qemu_rdma_poll()'s return type is uint64_t, even though it returns 0,
-1, or @ret, which is int. Its callers assign the return value to int
variables, then check whether it's negative. Unclean.
Return int instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230928132019.2544702-2-armbru@redhat.com>
There's a bug on dest that if a double fault triggered on dest qemu (a
network issue during postcopy-recover), we won't set PAUSED correctly
because we assumed we always came from ACTIVE.
Fix that by always overwriting the state to PAUSE.
We could also check for these two states, but maybe it's an overkill. We
did the same on the src QEMU to unconditionally switch to PAUSE anyway.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231004220240.167175-10-peterx@redhat.com>
We are sending a migration event of MIGRATION_STATUS_SETUP at
qemu_start_incoming_migration but never actually setting the state.
This creates a window between qmp_migrate_incoming and
process_incoming_migration_co where the migration status is still
MIGRATION_STATUS_NONE. Calling query-migrate during this time will
return an empty response even though the incoming migration command
has already been issued.
Commit 7cf1fe6d68 ("migration: Add migration events on target side")
has added support to the 'events' capability to the incoming part of
migration, but chose to send the SETUP event without setting the
state. I'm assuming this was a mistake.
This introduces a change in behavior, any QMP client waiting for the
SETUP event will hang, unless it has previously enabled the 'events'
capability. Having the capability enabled is sufficient to continue to
receive the event.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230712190742.22294-5-farosas@suse.de>
QEMU will crash if anyone tries to set tls-authz (which is a type
StrOrNull) with 'null' value. Fix it in the easy way by converting it to
qstring just like the other two tls parameters.
Cc: qemu-stable@nongnu.org # v4.0+
Fixes: d2f1d29b95 ("migration: add support for a "tls-authz" migration parameter")
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230905162335.235619-2-peterx@redhat.com>
Currently query-dirty-rate uses QEMU_CLOCK_REALTIME as
the source for start-time field. This translates to
clock_gettime(CLOCK_MONOTONIC), i.e. number of seconds
since host boot. This is not very useful. The only
reasonable use case of start-time I can imagine is to
check whether previously completed measurements are
too old or not. But this makes sense only if start-time
is reported as host wall-clock time.
This patch replaces source of start-time from
QEMU_CLOCK_REALTIME to QEMU_CLOCK_HOST.
Signed-off-by: Andrei Gudkov <gudkov.andrei@huawei.com>
Reviewed-by: Hyman Huang <yong.huang@smartx.com>
Message-Id: <399861531e3b24a1ecea2ba453fb2c3d129fb03a.1693905328.git.gudkov.andrei@huawei.com>
Signed-off-by: Hyman Huang <yong.huang@smartx.com>
For both save/load we actually share the logic on deciding whether a field
should exist. Merge the checks into a helper and use it for both save and
load. When doing so, add documentations and reformat the code to make it
much easier to read.
The real benefit here (besides code cleanups) is we add a trace-point for
this; this is a known spot where we can easily break migration
compatibilities between binaries, and this trace point will be critical for
us to identify such issues.
For example, this will be handy when debugging things like:
https://gitlab.com/qemu-project/qemu/-/issues/932
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230906204722.514474-1-peterx@redhat.com>
Allow an offset option to be specified as part of the file URI, in
the form "file:filename,offset=offset", where offset accepts the common
size suffixes, or the 0x prefix, but not both. Migration data is written
to and read from the file starting at offset. If unspecified, it defaults
to 0.
This is needed by libvirt to store its own data at the head of the file.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <1694182931-61390-3-git-send-email-steven.sistare@oracle.com>
Extend the migration URI to support file:<filename>. This can be used for
any migration scenario that does not require a reverse path. It can be
used as an alternative to 'exec:cat > file' in minimized containers that
do not contain /bin/sh, and it is easier to use than the fd:<fdname> URI.
It can be used in HMP commands, and as a qemu command-line parameter.
For best performance, guest ram should be shared and x-ignore-shared
should be true, so guest pages are not written to the file, in which case
the guest may remain running. If ram is not so configured, then the user
is advised to stop the guest first. Otherwise, a busy guest may re-dirty
the same page, causing it to be appended to the file multiple times,
and the file may grow unboundedly. That issue is being addressed in the
"fixed-ram" patch series.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Tested-by: Michael Galaxy <mgalaxy@akamai.com>
Reviewed-by: Michael Galaxy <mgalaxy@akamai.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <1694182931-61390-2-git-send-email-steven.sistare@oracle.com>
Previously, we got a confusion error that complains
the RDMAControlHeader.repeat:
qemu-system-x86_64: rdma: Too many requests in this message (3638950032).Bailing.
Actually, it's caused by an unexpected RDMAControlHeader.type.
After this patch, error will become:
qemu-system-x86_64: Unknown control message QEMU FILE
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230926100103.201564-2-lizhijian@fujitsu.com>
A few code paths exist in the source code,where a migration is
marked as failed via MIGRATION_STATUS_FAILED, but the failure happens
outside of migration.c
In such cases, an error_report() call is made, however the current
MigrationState is never updated with the error description, and hence
clients like libvirt never know the actual reason for the failure.
This patch covers such cases outside of migration.c and updates the
error description at the appropriate places.
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Tejus GK <tejus.gk@nutanix.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231003065538.244752-3-tejus.gk@nutanix.com>
Currently, a few code paths exist in the function vmstate_save_state_v,
which ultimately leads to a migration failure. However, an update in the
current MigrationState for the error description is never done.
vmstate.c somehow doesn't seem to allow the use of migrate_set_error due
to some dependencies for unit tests. Hence, this patch introduces a new
function vmstate_save_state_with_err, which will eventually propagate
the error message to savevm.c where a migrate_set_error call can be
eventually done.
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Tejus GK <tejus.gk@nutanix.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231003065538.244752-2-tejus.gk@nutanix.com>
When we sent a page through QEMUFile hooks (RDMA) there are three
posiblities:
- We are not using RDMA. return RAM_SAVE_CONTROL_DELAYED and
control_save_page() returns false to let anything else to proceed.
- There is one error but we are using RDMA. Then we return a negative
value, control_save_page() needs to return true.
- Everything goes well and RDMA start the sent of the page
asynchronously. It returns RAM_SAVE_CONTROL_DELAYED and we need to
return 1 for ram_save_page_legacy.
Clear?
I know, I know, the interface is as bad as it gets. I think that now
it is a bit clearer, but this needs to be done some other way.
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515195709.63843-16-quintela@redhat.com>
After this change, nothing abuses QEMUFile to account for data
transferrefd during migration.
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515195709.63843-15-quintela@redhat.com>
RDMA protocol is completely asynchronous, so in qemu_rdma_save_page()
they "invent" that a byte has been transferred. And then they call
qemu_file_credit_transfer() and ram_transferred_add() with that byte.
Just remove that calls as nothing has been sent.
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515195709.63843-14-quintela@redhat.com>
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515195709.63843-13-quintela@redhat.com>
Remove the one in control_save_page().
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515195709.63843-12-quintela@redhat.com>
Just create a variable for it, the same way that multifd does. This
way it is safe to use for other thread, etc, etc.
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515195709.63843-11-quintela@redhat.com>
We only care about the amount of bytes transferred. Flushing is done
by the system somewhere else.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230530183941.7223-4-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In the function qmp_migrate(), yank_unregister_instance() gets called
twice which isn't required. Hence, refactoring it so that it gets called
during the local_error cleanup.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Tejus GK <tejus.gk@nutanix.com>
Message-ID: <20230621130940.178659-3-tejus.gk@nutanix.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Local variables shadowing other local variables or parameters make the
code needlessly hard to understand. Tracked down with -Wshadow=local.
Clean up: delete inner declarations when they are actually redundant,
else rename variables.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Message-ID: <20230921121312.1301864-3-armbru@redhat.com>
qemu_rdma_save_page() reports polling error with error_report(), then
succeeds anyway. This is because the variable holding the polling
status *shadows* the variable the function returns. The latter
remains zero.
Broken since day one, and duplicated more recently.
Fixes: 2da776db48 (rdma: core logic)
Fixes: b390afd8c5 (migration/rdma: Fix out of order wrid)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Message-ID: <20230921121312.1301864-2-armbru@redhat.com>
Now that the return path thread is allowed to finish during a paused
migration, we can move the cleanup of the QEMUFiles to the main
migration thread.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-9-farosas@suse.de>
Replace the return path retry logic with finishing and restarting the
thread. This fixes a race when resuming the migration that leads to a
segfault.
Currently when doing postcopy we consider that an IO error on the
return path file could be due to a network intermittency. We then keep
the thread alive but have it do cleanup of the 'from_dst_file' and
wait on the 'postcopy_pause_rp' semaphore. When the user issues a
migrate resume, a new return path is opened and the thread is allowed
to continue.
There's a race condition in the above mechanism. It is possible for
the new return path file to be setup *before* the cleanup code in the
return path thread has had a chance to run, leading to the *new* file
being closed and the pointer set to NULL. When the thread is released
after the resume, it tries to dereference 'from_dst_file' and crashes:
Thread 7 "return path" received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7fffd1dbf700 (LWP 9611)]
0x00005555560e4893 in qemu_file_get_error_obj (f=0x0, errp=0x0) at ../migration/qemu-file.c:154
154 return f->last_error;
(gdb) bt
#0 0x00005555560e4893 in qemu_file_get_error_obj (f=0x0, errp=0x0) at ../migration/qemu-file.c:154
#1 0x00005555560e4983 in qemu_file_get_error (f=0x0) at ../migration/qemu-file.c:206
#2 0x0000555555b9a1df in source_return_path_thread (opaque=0x555556e06000) at ../migration/migration.c:1876
#3 0x000055555602e14f in qemu_thread_start (args=0x55555782e780) at ../util/qemu-thread-posix.c:541
#4 0x00007ffff38d76ea in start_thread (arg=0x7fffd1dbf700) at pthread_create.c:477
#5 0x00007ffff35efa6f in clone () at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95
Here's the race (important bit is open_return_path happening before
migration_release_dst_files):
migration | qmp | return path
--------------------------+-----------------------------+---------------------------------
qmp_migrate_pause()
shutdown(ms->to_dst_file)
f->last_error = -EIO
migrate_detect_error()
postcopy_pause()
set_state(PAUSED)
wait(postcopy_pause_sem)
qmp_migrate(resume)
migrate_fd_connect()
resume = state == PAUSED
open_return_path <-- TOO SOON!
set_state(RECOVER)
post(postcopy_pause_sem)
(incoming closes to_src_file)
res = qemu_file_get_error(rp)
migration_release_dst_files()
ms->rp_state.from_dst_file = NULL
post(postcopy_pause_rp_sem)
postcopy_pause_return_path_thread()
wait(postcopy_pause_rp_sem)
rp = ms->rp_state.from_dst_file
goto retry
qemu_file_get_error(rp)
SIGSEGV
-------------------------------------------------------------------------------------------
We can keep the retry logic without having the thread alive and
waiting. The only piece of data used by it is the 'from_dst_file' and
it is only allowed to proceed after a migrate resume is issued and the
semaphore released at migrate_fd_connect().
Move the retry logic to outside the thread by waiting for the thread
to finish before pausing the migration.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-8-farosas@suse.de>
We'll start calling the await_return_path_close_on_source() function
from other parts of the code, so move all of the related checks and
tracepoints into it.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-7-farosas@suse.de>
This file is owned by the return path thread which is already doing
cleanup.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-6-farosas@suse.de>
It's not safe to call qemu_file_shutdown() on the to_dst_file without
first checking for the file's presence under the lock. The cleanup of
this file happens at postcopy_pause() and migrate_fd_cleanup() which
are not necessarily running in the same thread as migrate_fd_cancel().
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-5-farosas@suse.de>
We cannot call qemu_file_shutdown() on the return path file without
taking the file lock. The return path thread could be running it's
cleanup code and have just cleared the from_dst_file pointer.
Checking ms->to_dst_file for errors could also race with
migrate_fd_cleanup() which clears the to_dst_file pointer.
Protect both accesses by taking the file lock.
This was caught by inspection, it should be rare, but the next patches
will start calling this code from other places, so let's do the
correct thing.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-4-farosas@suse.de>
We don't need to set the rp_state.error right after a shutdown because
qemu_file_shutdown() always sets the QEMUFile error, so the return
path thread would have seen it and set the rp error itself.
Setting the error outside of the thread is also racy because the
thread could clear it after we set it.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-3-farosas@suse.de>
We hit intermit CI issue on failing at migration-test over the unit test
preempt/plain:
qemu-system-x86_64: Unable to read from socket: Connection reset by peer
Memory content inconsistency at 5b43000 first_byte = bd last_byte = bc current = 4f hit_edge = 1
**
ERROR:../tests/qtest/migration-test.c:300:check_guests_ram: assertion failed: (bad == 0)
(test program exited with status code -6)
Fabiano debugged into it and found that the preempt thread can quit even
without receiving all the pages, which can cause guest not receiving all
the pages and corrupt the guest memory.
To make sure preempt thread finished receiving all the pages, we can rely
on the page_requested_count being zero because preempt channel will only
receive requested page faults. Note, not all the faulted pages are required
to be sent via the preempt channel/thread; imagine the case when a
requested page is just queued into the background main channel for
migration, the src qemu will just still send it via the background channel.
Here instead of spinning over reading the count, we add a condvar so the
main thread can wait on it if that unusual case happened, without burning
the cpu for no good reason, even if the duration is short; so even if we
spin in this rare case is probably fine. It's just better to not do so.
The condvar is only used when that special case is triggered. Some memory
ordering trick is needed to guarantee it from happening (against the
preempt thread status field), so the main thread will always get a kick
when that triggers correctly.
Closes: https://gitlab.com/qemu-project/qemu/-/issues/1886
Debugged-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230918172822.19052-2-farosas@suse.de>
Add a new .save_prepare() handler to struct SaveVMHandlers. This handler
is called early, even before migration starts, and can be used by
devices to perform early checks.
Refactor migrate_init() to be able to return errors and call
.save_prepare() from there.
Suggested-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Initialization of mig_stats, compression_counters and VFIO bytes
transferred is hard-coded in migration code path and snapshot code path.
Make the code cleaner by initializing them in migrate_init().
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The functions in target.c are not static, yet they don't have a proper
migration prefix. Add such prefix.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The ongoing QEMU multi-queue block layer effort makes it possible for multiple
threads to process I/O in parallel. The nbd block driver is not compatible with
the multi-queue block layer yet because QIOChannel cannot be used easily from
coroutines running in multiple threads. This series changes the QIOChannel API
to make that possible.
In the current API, calling qio_channel_attach_aio_context() sets the
AioContext where qio_channel_yield() installs an fd handler prior to yielding:
qio_channel_attach_aio_context(ioc, my_ctx);
...
qio_channel_yield(ioc); // my_ctx is used here
...
qio_channel_detach_aio_context(ioc);
This API design has limitations: reading and writing must be done in the same
AioContext and moving between AioContexts involves a cumbersome sequence of API
calls that is not suitable for doing on a per-request basis.
There is no fundamental reason why a QIOChannel needs to run within the
same AioContext every time qio_channel_yield() is called. QIOChannel
only uses the AioContext while inside qio_channel_yield(). The rest of
the time, QIOChannel is independent of any AioContext.
In the new API, qio_channel_yield() queries the AioContext from the current
coroutine using qemu_coroutine_get_aio_context(). There is no need to
explicitly attach/detach AioContexts anymore and
qio_channel_attach_aio_context() and qio_channel_detach_aio_context() are gone.
One coroutine can read from the QIOChannel while another coroutine writes from
a different AioContext.
This API change allows the nbd block driver to use QIOChannel from any thread.
It's important to keep in mind that the block driver already synchronizes
QIOChannel access and ensures that two coroutines never read simultaneously or
write simultaneously.
This patch updates all users of qio_channel_attach_aio_context() to the
new API. Most conversions are simple, but vhost-user-server requires a
new qemu_coroutine_yield() call to quiesce the vu_client_trip()
coroutine when not attached to any AioContext.
While the API is has become simpler, there is one wart: QIOChannel has a
special case for the iohandler AioContext (used for handlers that must not run
in nested event loops). I didn't find an elegant way preserve that behavior, so
I added a new API called qio_channel_set_follow_coroutine_ctx(ioc, true|false)
for opting in to the new AioContext model. By default QIOChannel uses the
iohandler AioHandler. Code that formerly called
qio_channel_attach_aio_context() now calls
qio_channel_set_follow_coroutine_ctx(ioc, true) once after the QIOChannel is
created.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20230830224802.493686-5-stefanha@redhat.com>
[eblake: also fix migration/rdma.c]
Signed-off-by: Eric Blake <eblake@redhat.com>
We can fail the blk_insert_bs() at init_blk_migration(), leaving the
BlkMigDevState without a dirty_bitmap and BlockDriverState. Account
for the possibly missing elements when doing cleanup.
Fix the following crashes:
Thread 1 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x0000555555ec83ef in bdrv_release_dirty_bitmap (bitmap=0x0) at ../block/dirty-bitmap.c:359
359 BlockDriverState *bs = bitmap->bs;
#0 0x0000555555ec83ef in bdrv_release_dirty_bitmap (bitmap=0x0) at ../block/dirty-bitmap.c:359
#1 0x0000555555bba331 in unset_dirty_tracking () at ../migration/block.c:371
#2 0x0000555555bbad98 in block_migration_cleanup_bmds () at ../migration/block.c:681
Thread 1 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x0000555555e971ff in bdrv_op_unblock (bs=0x0, op=BLOCK_OP_TYPE_BACKUP_SOURCE, reason=0x0) at ../block.c:7073
7073 QLIST_FOREACH_SAFE(blocker, &bs->op_blockers[op], list, next) {
#0 0x0000555555e971ff in bdrv_op_unblock (bs=0x0, op=BLOCK_OP_TYPE_BACKUP_SOURCE, reason=0x0) at ../block.c:7073
#1 0x0000555555e9734a in bdrv_op_unblock_all (bs=0x0, reason=0x0) at ../block.c:7095
#2 0x0000555555bbae13 in block_migration_cleanup_bmds () at ../migration/block.c:690
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Message-id: 20230731203338.27581-1-farosas@suse.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is how everything else in QEMUFile is structured.
As a bonus they are three less lines of code.
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-ID: <20230530183941.7223-17-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It was not used outside of qemu_file.c anyways.
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-ID: <20230530183941.7223-21-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It is not used outside of qemu_file, and it shouldn't.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230530183941.7223-19-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We do a qemu_fclose() just after that, that also does a qemu_fflush(),
so remove one qemu_fflush().
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230530183941.7223-3-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Fast don't say much. Noflush indicates more clearly that it is like
qemu_file_transferred but without the flush.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230530183941.7223-2-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
qemu_start_incoming_migration needs to check the number of multifd
channels or postcopy ram channels to configure the backlog parameter (i.e.
the maximum length to which the queue of pending connections for sockfd
may grow) of listen(). So enforce the usage of postcopy-preempt and
multifd as below:
- need to use "-incoming defer" on the destination; and
- set_capability and set_parameter need to be done before migrate_incoming
Otherwise, disable the use of the features and report error messages to
remind users to adjust the commands.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230606101910.20456-2-wei.w.wang@intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
There are places in migration.c where the migration is marked failed with
MIGRATION_STATUS_FAILED, but the failure reason is never updated. Hence
libvirt doesn't know why the migration failed when it queries for it.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Tejus GK <tejus.gk@nutanix.com>
Message-ID: <20230621130940.178659-2-tejus.gk@nutanix.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Extend query-migrate to provide throttle time and estimated
ring full time with dirty-limit capability enabled, through which
we can observe if dirty limit take effect during live migration.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-ID: <168733225273.5845.15871826788879741674-8@git.sr.ht>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Implement dirty-limit convergence algo for live migration,
which is kind of like auto-converge algo but using dirty-limit
instead of cpu throttle to make migration convergent.
Enable dirty page limit if dirty_rate_high_cnt greater than 2
when dirty-limit capability enabled, Disable dirty-limit if
migration be canceled.
Note that "set_vcpu_dirty_limit", "cancel_vcpu_dirty_limit"
commands are not allowed during dirty-limit live migration.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <168733225273.5845.15871826788879741674-7@git.sr.ht>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This commit is prepared for the implementation of dirty-limit
convergence algo.
The detection logic of throttling condition can apply to both
auto-converge and dirty-limit algo, putting it's position
before the checking logic for auto-converge feature.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-ID: <168733225273.5845.15871826788879741674-6@git.sr.ht>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Check if block migration is running before throttling
guest down in auto-converge way.
Note that this modification is kind of like code clean,
because block migration does not depend on auto-converge
capability, so the order of checks can be adjusted.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <168618975839.6361.17407633874747688653-5@git.sr.ht>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce migration dirty-limit capability, which can
be turned on before live migration and limit dirty
page rate durty live migration.
Introduce migrate_dirty_limit function to help check
if dirty-limit capability enabled during live migration.
Meanwhile, refactor vcpu_dirty_rate_stat_collect
so that period can be configured instead of hardcoded.
dirty-limit capability is kind of like auto-converge
but using dirty limit instead of traditional cpu-throttle
to throttle guest down. To enable this feature, turn on
the dirty-limit capability before live migration using
migrate-set-capabilities, and set the parameters
"x-vcpu-dirty-limit-period", "vcpu-dirty-limit" suitably
to speed up convergence.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <168618975839.6361.17407633874747688653-4@git.sr.ht>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce "vcpu-dirty-limit" migration parameter used
to limit dirty page rate during live migration.
"vcpu-dirty-limit" and "x-vcpu-dirty-limit-period" are
two dirty-limit-related migration parameters, which can
be set before and during live migration by qmp
migrate-set-parameters.
This two parameters are used to help implement the dirty
page rate limit algo of migration.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <168618975839.6361.17407633874747688653-3@git.sr.ht>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce "x-vcpu-dirty-limit-period" migration experimental
parameter, which is in the range of 1 to 1000ms and used to
make dirtyrate calculation period configurable.
Currently with the "x-vcpu-dirty-limit-period" varies, the
total time of live migration changes, test results show the
optimal value of "x-vcpu-dirty-limit-period" ranges from
500ms to 1000 ms. "x-vcpu-dirty-limit-period" should be made
stable once it proves best value can not be determined with
developer's experiments.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <168618975839.6361.17407633874747688653-2@git.sr.ht>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This doubly linked list is common for all the multifd and migration
threads so we need to avoid concurrent access.
Add a mutex to protect the data from concurrent access. This fixes a
crash when removing two MigrationThread objects from the list at the
same time during cleanup of multifd threads.
Fixes: 671326201d ("migration: Introduce interface query-migrationthreads")
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230607161306.31425-3-farosas@suse.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We're about to add more functions to this file so make it use the same
coding style as the rest of the code.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230607161306.31425-2-farosas@suse.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
virtio-mem wants to know whether it should not mess with the RAMBlock
content (e.g., discard RAM, preallocate memory) on incoming migration.
So let's expose that function as migrate_ram_is_ignored() in
migration/misc.h
Message-ID: <20230706075612.67404-4-david@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
The only migrate_fd_error() call sites are in "migration/migration.c",
which is also where we define migrate_fd_error(). Make the function
static, and remove its declaration from "migration/migration.h".
Cc: Juan Quintela <quintela@redhat.com> (maintainer:Migration)
Cc: Leonardo Bras <leobras@redhat.com> (reviewer:Migration)
Cc: Peter Xu <peterx@redhat.com> (reviewer:Migration)
Cc: qemu-trivial@nongnu.org
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2018404
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It cuts back on those awkward, duplicated !(has_resume && resume)
expressions.
Cc: Juan Quintela <quintela@redhat.com> (maintainer:Migration)
Cc: Leonardo Bras <leobras@redhat.com> (reviewer:Migration)
Cc: Peter Xu <peterx@redhat.com> (reviewer:Migration)
Cc: qemu-trivial@nongnu.org
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2018404
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, VFIO bytes_transferred is not reset properly:
1. bytes_transferred is not reset after a VM snapshot (so a migration
following a snapshot will report incorrect value).
2. bytes_transferred is a single counter for all VFIO devices, however
upon migration failure it is reset multiple times, by each VFIO
device.
Fix it by introducing a new function vfio_reset_bytes_transferred() and
calling it during migration and snapshot start.
Remove existing bytes_transferred reset in VFIO migration state
notifier, which is not needed anymore.
Fixes: 3710586caa ("qapi: Add VFIO devices migration stats in Migration stats")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Now that switchover ack logic has been implemented, enable the
capability.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Implement switchover ack logic. This prevents the source from stopping
the VM and completing the migration until an ACK is received from the
destination that it's OK to do so.
To achieve this, a new SaveVMHandlers handler switchover_ack_needed()
and a new return path message MIG_RP_MSG_SWITCHOVER_ACK are added.
The switchover_ack_needed() handler is called during migration setup in
the destination to check if switchover ack is used by the migrated
device.
When switchover is approved by all migrated devices in the destination
that support this capability, the MIG_RP_MSG_SWITCHOVER_ACK return path
message is sent to the source to notify it that it's OK to do
switchover.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Migration downtime estimation is calculated based on bandwidth and
remaining migration data. This assumes that loading of migration data in
the destination takes a negligible amount of time and that downtime
depends only on network speed.
While this may be true for RAM, it's not necessarily true for other
migrated devices. For example, loading the data of a VFIO device in the
destination might require from the device to allocate resources, prepare
internal data structures and so on. These operations can take a
significant amount of time which can increase migration downtime.
This patch adds a new capability "switchover ack" that prevents the
source from stopping the VM and completing the migration until an ACK
is received from the destination that it's OK to do so.
This can be used by migrated devices in various ways to reduce downtime.
For example, a device can send initial precopy metadata to pre-allocate
resources in the destination and use this capability to make sure that
the pre-allocation is completed before the source VM is stopped, so it
will have full effect.
This new capability relies on the return path capability to communicate
from the destination back to the source.
The actual implementation of the capability will be added in the
following patches.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since we *might* have user emulation with softmmu,
use the clearer 'CONFIG_SYSTEM_ONLY' key to check
for system emulation.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-9-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
migrate_ignore_shared() is an optimization that avoids copying memory
that is visible and can be mapped on the target. However, a
memory-backend-ram or a memory-backend-memfd block with the RAM_SHARED
flag set is not migrated when migrate_ignore_shared() is true. This is
wrong, because the block has no named backing store, and its contents will
be lost. To fix, ignore shared memory iff it is a named file. Define a
new flag RAM_NAMED_FILE to distinguish this case.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <1686151116-253260-1-git-send-email-steven.sistare@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Mechanical change running Coccinelle spatch with content
generated from the qom-cast-macro-clean-cocci-gen.py added
in the previous commit.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230601093452.38972-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently, it is only done when the iteration finishes successfully.
Not cleaning up the userfaultfd write protection can lead to
symptoms/issues such as the process hanging in memmove or GDB not
being able to attach.
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20230526115908.196171-1-f.ebner@proxmox.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
1. Otherwise failed migration just drops guest-panicked state, which is
not good for management software.
2. We do keep different paused states like guest-panicked during
migration with help of global_state state.
3. We do restore running state on source when migration is cancelled or
failed.
4. "postmigrate" state is documented as "guest is paused following a
successful 'migrate'", so originally it's only for successful path
and we never documented current behavior.
Let's restore paused states like guest-panicked in case of cancel or
fail too. Allow same transitions like for inmigrate state.
This commit changes the behavior that was introduced by commit
42da5550d6 "migration: set state to post-migrate on failure" and
provides a bit different fix on related
https://bugzilla.redhat.com/show_bug.cgi?id=1355683
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230517123752.21615-6-vsementsov@yandex-team.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
No logic change here, only refactoring. That's a preparation for next
commit where we finally restore the stopped vm state on migration
failure or cancellation.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230517123752.21615-5-vsementsov@yandex-team.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Actually global_state_store() can never fail. Let's get rid of extra
error paths.
To make things clear, use new runstate_get() and use same approach for
global_state_store() and global_state_store_running().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230517123752.21615-3-vsementsov@yandex-team.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
All callers now pass is_external=false to aio_set_fd_handler() and
aio_set_event_notifier(). The aio_disable_external() API that
temporarily disables fd handlers that were registered is_external=true
is therefore dead code.
Remove aio_disable_external(), aio_enable_external(), and the
is_external arguments to aio_set_fd_handler() and
aio_set_event_notifier().
The entire test-fdmon-epoll test is removed because its sole purpose was
testing aio_disable_external().
Parts of this patch were generated using the following coccinelle
(https://coccinelle.lip6.fr/) semantic patch:
@@
expression ctx, fd, is_external, io_read, io_write, io_poll, io_poll_ready, opaque;
@@
- aio_set_fd_handler(ctx, fd, is_external, io_read, io_write, io_poll, io_poll_ready, opaque)
+ aio_set_fd_handler(ctx, fd, io_read, io_write, io_poll, io_poll_ready, opaque)
@@
expression ctx, notifier, is_external, io_read, io_poll, io_poll_ready;
@@
- aio_set_event_notifier(ctx, notifier, is_external, io_read, io_poll, io_poll_ready)
+ aio_set_event_notifier(ctx, notifier, io_read, io_poll, io_poll_ready)
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230516190238.8401-21-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The items in migration_files are built for libmigration and included
info softmmu_ss from there; no need to also include them directly.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Perform the function selection once, and only if CONFIG_AVX512_OPT
is enabled. Centralize the selection to xbzrle.c, instead of
spreading the init across 3 files.
Remove xbzrle-bench.c. The benefit of being able to benchmark
the different implementations is less important than not peeking
into the internals of the implementation.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Place the CONFIG_AVX512BW_OPT block at the top,
which will aid function selection in the next patch.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Hi
Based on latest reviewed parts of migration:
- Disable colo (vladimir)
- Migration atomic counters (juan)
Please apply.
-----BEGIN PGP SIGNATURE-----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=3x32
-----END PGP SIGNATURE-----
Merge tag 'migration-20230518-pull-request' of https://gitlab.com/juan.quintela/qemu into staging
Migration Pull request
Hi
Based on latest reviewed parts of migration:
- Disable colo (vladimir)
- Migration atomic counters (juan)
Please apply.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEGJn/jt6/WMzuA0uC9IfvGFhy1yMFAmRmXJUACgkQ9IfvGFhy
# 1yNRAxAAjDYJELL34Qovt/WE9qKhYJEvIUGTl1IMWJ22YMFnqIFKRdka57dWoU3P
# 7EK1BHmokEEtzGT7Fe1ecERXsOwQIJDIkDTJ5g8Oc8Jt1iqY1AC8h5T+LghijCar
# mbZ6qWHaSjsg2lmek/xc9quymzFGGK36PSyB5WkaLRviKQn4RIkEDpUaWny7nDbA
# Q8zJJpBqNFqKfC5/DN0ePa3QQscXQJhey3nxqFd8hYp8RFNIV5UJVW5Lf6ombtK7
# atgdWC4ckkfO2z3OsghKeo/UiMFWpPktgBVVMhDLmk+P/E6czc2gfzD6SCvrPKTj
# XowI8hro22HVmq9bEY8PtbjMOfpxrAxer+tM2KR/0O9l3UzUacFsi7KGqCJ1/trQ
# 1tSDjlgyczb8GOgLwwxj8XE+jPHPfVrzCNfDqrBKBNxz6nnZSdZUwhV5mG8FdVtm
# oVVV96BIrNXLl/lIxYIFD/Zyvl8/lrSWQdLkEHTzihYQeXaQfyvPVbV/dOLT4sii
# YUuGCuEhF+DW/qz43G1krwq5/bfxsiZoQzrMV/Odtf0wYQKkabA3KNBIda/vxBCR
# dsLQ7QtmOwKmCzjqw4LUov9vDNYOYr98o7ZqwJ3qeKL4QgFwtEZUFO3VW6UR8fnF
# arVXiTn9wVlkTpu4sT5hLm9400iadhX4Fppji7Ce0tUpLbWbghA=
# =3x32
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 18 May 2023 10:12:53 AM PDT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [undefined]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'migration-20230518-pull-request' of https://gitlab.com/juan.quintela/qemu:
migration: Fix duplicated included in meson.build
migration/multifd: Compute transferred bytes correctly
migration: We don't need the field rate_limit_used anymore
migration: Use migration_transferred_bytes() to calculate rate_limit
migration: Add a trace for migration_transferred_bytes
migration: Move migration_total_bytes() to migration-stats.c
migration: Move rate_limit_max and rate_limit_used to migration_stats
qemu-file: Account for rate_limit usage on qemu_fflush()
migration: Don't use INT64_MAX for unlimited rate
migration: process_incoming_migration_co(): move colo part to colo
migration: split migration_incoming_co
configure: add --disable-colo-proxy option
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is the commint with the merge error (not in the submited patch).
commit 52623f23b0
Author: Lukas Straub <lukasstraub2@web.de>
Date: Thu Apr 20 11:48:35 2023 +0200
ram-compress.c: Make target independent
Make ram-compress.c target independent.
Fixes: 52623f23b0
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230509170217.83246-1-quintela@redhat.com>
In the past, we had to put the in the main thread all the operations
related with sizes due to qemu_file not beeing thread safe. As now
all counters are atomic, we can update the counters just after the
do the write. As an aditional bonus, we are able to use the right
value for the compression methods. Right now we were assuming that
there were no compression at all.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230515195709.63843-17-quintela@redhat.com>
Since previous commit, we calculate how much data we have send with
migration_transferred_bytes() so no need to maintain this counter and
remember to always update it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230515195709.63843-10-quintela@redhat.com>
Once there rename it to migration_transferred_bytes() and pass a
QEMUFile instead of a migration object.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230515195709.63843-7-quintela@redhat.com>
These way we can make them atomic and use this functions from any
place. I also moved all functions that use rate_limit to
migration-stats.
Functions got renamed, they are not qemu_file anymore.
qemu_file_rate_limit -> migration_rate_exceeded
qemu_file_set_rate_limit -> migration_rate_set
qemu_file_get_rate_limit -> migration_rate_get
qemu_file_reset_rate_limit -> migration_rate_reset
qemu_file_acct_rate_limit -> migration_rate_account.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515195709.63843-6-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
That is the moment we know we have transferred something.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230515195709.63843-5-quintela@redhat.com>
Define and use RATE_LIMIT_DISABLED instead.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Message-Id: <20230515195709.63843-2-quintela@redhat.com>
Let's make better public interface for COLO: instead of
colo_process_incoming_thread and not trivial logic around creating the
thread let's make simple colo_incoming_co(), hiding implementation from
generic code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515130640.46035-4-vsementsov@yandex-team.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Originally, migration_incoming_co was introduced by
25d0c16f62
"migration: Switch to COLO process after finishing loadvm"
to be able to enter from COLO code to one specific yield point, added
by 25d0c16f62.
Later in 923709896b
"migration: poll the cm event for destination qemu"
we reused this variable to wake the migration incoming coroutine from
RDMA code.
That was doubtful idea. Entering coroutines is a very fragile thing:
you should be absolutely sure which yield point you are going to enter.
I don't know how much is it safe to enter during qemu_loadvm_state()
which I think what RDMA want to do. But for sure RDMA shouldn't enter
the special COLO-related yield-point. As well, COLO code doesn't want
to enter during qemu_loadvm_state(), it want to enter it's own specific
yield-point.
As well, when in 8e48ac9586
"COLO: Add block replication into colo process" we added
bdrv_invalidate_cache_all() call (now it's called activate_all())
it became possible to enter the migration incoming coroutine during
that call which is wrong too.
So, let't make these things separate and disjoint: loadvm_co for RDMA,
non-NULL during qemu_loadvm_state(), and colo_incoming_co for COLO,
non-NULL only around specific yield.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230515130640.46035-3-vsementsov@yandex-team.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The global dirty log synchronization is used when KVM and dirty ring
are enabled. There is a particularity for ARM64 where the backup
bitmap is used to track dirty pages in non-running-vcpu situations.
It means the dirty ring works with the combination of ring buffer
and backup bitmap. The dirty bits in the backup bitmap needs to
collected in the last stage of live migration.
In order to identify the last stage of live migration and pass it
down, an extra parameter is added to the relevant functions and
callbacks. This last stage indicator isn't used until the dirty
ring is enabled in the subsequent patches.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-Id: <20230509022122.20888-2-gshan@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All types used are forward-declared in "qemu/typedefs.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230405160454.97436-2-philmd@linaro.org>
[thuth: Add hw/core/cpu.h to migration/dirtyrate.c to fix compile failure]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Function is already quite long.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230508130909.65420-7-quintela@redhat.com>
Change all the functions that use it. It was already passed as
uint64_t.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230508130909.65420-6-quintela@redhat.com>
It is really size_t. Everything else uses uint64_t, so move this to
uint64_t as well. A size can't be negative anyways.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230508130909.65420-5-quintela@redhat.com>
