Currently, both qemu_devices_reset() and MachineClass::reset() use
ShutdownCause for the reason of the reset. However, the Resettable
interface uses ResetState, so ShutdownCause needs to be translated to
ResetType somewhere. Translating it qemu_devices_reset() makes adding
new reset types harder, as they cannot always be matched to a single
ShutdownCause here, and devices may need to check the ResetType to
determine what to reset and if to reset at all.
This patch moves this translation up in the call stack to
qemu_system_reset() and updates all MachineClass children to use the
ResetType instead.
Message-ID: <20240904103722.946194-2-jmarcin@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Juraj Marcin <jmarcin@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
The machine calls serial_hds_isa_init() which is provided by serial-isa.c,
guarded by SERIAL_ISA.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240814181534.218964-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The ppc_hash64_hpt_base() and ppc_hash64_hpt_mask() functions are
mostly used by mmu-hash64.c only but there is one call to
ppc_hash64_hpt_mask() in hw/ppc/spapr_vhyp_mmu.c.in a helper function
that can be moved to mmu-hash64.c which allows these functions to be
removed from the header.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
SPI controller device model supports a connection to a single SPI responder.
This provide access to SPI seeproms, TPM, flash device and an ADC controller.
All SPI function control is mapped into the SPI register space to enable full
control by firmware. In this commit SPI configuration component is modelled
which contains all SPI configuration and status registers as well as the hold
registers for data to be sent or having been received.
An existing QEMU SSI framework is used and SSI_BUS is created.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
[np: Fix FDT macro compile for qtest]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Recent POWER CPUs can operate in "LPAR per core" or "LPAR per thread"
modes. In per-core mode, some SPRs and IPI doorbells are shared between
threads in a core. In per-thread mode, supervisor and user state is
not shared between threads.
OpenPOWER systems after POWER8 use LPAR per thread mode, and it is
required for KVM. Enterprise systems use LPAR per core mode, as they
partition the machine by core.
Implement a lpar-per-core machine option for powernv machines. This
is fixed true for POWER8 machines, and defaults off for P9 and P10.
With this change, powernv8 SMT now works sufficiently to run Linux,
with a single socket. Multi-threaded KVM guests still have problems,
as does multi-socket Linux boot.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The PC unit in the processor core contains xscom registers that provide
low level status and control of the CPU.
This implements "direct controls", sufficient for skiboot firmware,
which uses it to send NMI IPIs between CPUs.
POWER10 is sufficiently different from POWER9 (particularly with respect
to QME and special wakeup) that it is not trivial to implement POWER9
support by reusing the code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power CPUs have an execution control facility that can pause, resume,
and cause NMIs, among other things. Add a function that will nmi a CPU
and resume it if it was paused, in preparation for implementing the
control facility.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Big-core implementation is complete, so expose it as a machine
property that may be set with big-core=on option on powernv9 and
powernv10 machines.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER10 has a quirk in its ChipTOD addressing that requires the even
small-core to be selected even when programming the odd small-core.
This allows skiboot chiptod init to run in big-core mode.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power9/10 CPUs have PVR[51] set in small-core mode and clear in big-core
mode. This is used by skiboot firmware.
PVR is not hypervisor-privileged but it is not so important that spapr
to implement this because it's generally masked out of PVR matching code
in kernels, and only used by firmware.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
device-tree building needs to account for big-core mode, because it is
driven by qemu cores (small cores). Every second core should be skipped,
and every core should describe threads for both small-cores that make
up the big core.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER9 and POWER10 machines come in two variants, big-core and
small-core. Big-core machines are SMT8 from software's point of view,
but the low level platform topology ("xscom registers and pervasive
addressing"), these look more like a pair of small cores ganged
together.
Presently the way this is modelled is to create one SMT8 PnvCore and add
special cases to xscom and pervasive for big-core mode that tries to
split this into two small cores, but this is becoming too complicated to
manage.
A better approach is to create 2 core structures and ganging them
together to look like an SMT8 core in TCG. Then the xscom and pervasive
models mostly do not need to differentiate big and small core modes.
This change adds initial mode bits and QEMU topology handling to
split SMT8 cores into 2xSMT4 cores.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The decision to branch out to a slower SMT path in instruction
emulation will become a bit more complicated with the way that
"big-core" topology that will be implemented in subsequent changes.
Hide these details from the wider CPU emulation code with a bool
has_smt_siblings flag that can be set by machine initialisation.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The way SMT thread siblings are matched is clunky, using hard-coded
logic that checks the PIR SPR.
Change that to use a new core_index variable in the CPUPPCState,
where all siblings have the same core_index. CPU realize routines have
flexibility in setting core/sibling topology.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The chip_pir chip class method allows the platform to set the PIR
processor identification register. Extend this to a more general
ID function which also allows the TIR to be set. This is in
preparation for "big core", which is a more complicated topology
of cores and threads.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Use a class attribute to specify the number of SMT threads per core
permitted for different machines, 8 for powernv8 and 4 for powernv9/10.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The timebase state machine is per per-core state and can be driven
by any thread in the core. It is currently implemented as a hack
where the state is in a CPU structure and only thread 0's state is
accessed by the chiptod, which limits programming the timebase
side of the state machine to thread 0 of a core.
Move the state out into PnvCore and share it among all threads.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This helps move core state from CPU to core structures.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
One of the functions of the ADU is indirect memory access engines that
send and receive data via ADU registers.
This implements the ADU LPC memory access functionality sufficiently
for IBM proprietary firmware to access the UART and print characters
to the serial port as it does on real hardware.
This requires a linkage between adu and lpc, which allows adu to
perform memory access in the lpc space.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This implements a framework for an ADU unit model.
The ADU unit actually implements XSCOM, which is the bridge between MMIO
and PIB. However it also includes control and status registers and other
functions that are exposed as PIB (xscom) registers.
To keep things simple, pnv_xscom.c remains the XSCOM bridge
implementation, and pnv_adu.c implements the ADU registers and other
functions.
So far, just the ADU no-op registers in the pnv_xscom.c default handler
are moved over to the adu model.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The POWER8 LPC ISA device irqs all get combined and reported to the line
connected the PSI LPCHC irq. POWER9 changed this so only internal LPC
host controller irqs use that line, and the device irqs get routed to
4 new lines connected to PSI SERIRQ0-3.
POWER9 also introduced a new feature that automatically clears the irq
status in the LPC host controller when EOI'ed, so software does not have
to.
The powernv OPAL (skiboot) firmware managed to work because the LPCHC
irq handler scanned all LPC irqs and handled those including clearing
status even on POWER9 systems. So LPC irqs worked despite OPAL thinking
it was running in POWER9 mode. After this change, UART interrupts show
up on serirq1 which is where OPAL routes them to:
cat /proc/interrupts
...
20: 0 XIVE-IRQ 1048563 Level opal-psi#0:lpchc
...
25: 34 XIVE-IRQ 1048568 Level opal-psi#0:lpc_serirq_mux1
Whereas they previously turn up on lpchc.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The LPC HC irq status register bits are set when an LPC IRQSER input is
asserted. These irq status bits drive the PSI irq to the CPU interrupt
controller. The LPC HC irq status bits are cleared by software writing
to the register with 1's for the bits to clear.
Existing register write was clearing the irq status bits even when the
input was asserted, this results in interrupts being lost.
This fix changes the behavior to keep track of the device IRQ status
in internal state that is separate from the irq status register, and
only allowing the irq status bits to be cleared if the associated
input is not asserted.
Signed-off-by: Glenn Miles <milesg@linux.ibm.com>
[np: rebased before P9 PSI SERIRQ patch, adjust changelog/comments]
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power10 DD1.0 was dropped in:
commit 8f054d9ee8 ("ppc: Drop support for POWER9 and POWER10 DD1 chips")
Use the newer Power10 DD2 chips cfam id.
Signed-off-by: Aditya Gupta <adityag@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
FDT properties are aligned by 4 bytes, not 8 bytes.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This fixes LeakSanitizer warnings.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This cap did not add the migration code when it was introduced. This
results in migration failure when changing the default using the
command line.
Cc: qemu-stable@nongnu.org
Fixes: ccc5a4c5e1 ("spapr: Add SPAPR_CAP_AIL_MODE_3 for AIL mode 3 support for H_SET_MODE hcall")
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Makes the code more comprehensible, matches the datasheet and
the piix4 device model.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240704205854.18537-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
A bunch of improvements:
- vhost dirty log is now only scanned once, not once per device
- virtio and vhost now support VIRTIO_F_NOTIFICATION_DATA
- cxl gained DCD emulation support
- pvpanic gained shutdown support
- beginning of patchset for Generic Port Affinity Structure
- s3 support
- friendlier error messages when boot fails on some illegal configs
- for vhost-user, VHOST_USER_SET_LOG_BASE is now only sent once
- part of vhost-user support for any POSIX system -
not yet enabled due to qtest failures
- sr-iov VF setup code has been reworked significantly
- new tests, particularly for risc-v ACPI
- bugfixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmaF068PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp+DMIAMC//mBXIZlPprfhb5cuZklxYi31Acgu5TUr
njqjCkN+mFhXXZuc3B67xmrQ066IEPtsbzCjSnzuU41YK4tjvO1g+LgYJBv41G16
va2k8vFM5pdvRA+UC9li1CCIPxiEcszxOdzZemj3szWLVLLUmwsc5OZLWWeFA5m8
vXrrT9miODUz3z8/Xn/TVpxnmD6glKYIRK/IJRzzC4Qqqwb5H3ji/BJV27cDUtdC
w6ns5RYIj5j4uAiG8wQNDggA1bMsTxFxThRDUwxlxaIwAcexrf1oRnxGRePA7PVG
BXrt5yodrZYR2sR6svmOOIF3wPMUDKdlAItTcEgYyxaVo5rAdpc=
=p9h4
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio: features,fixes
A bunch of improvements:
- vhost dirty log is now only scanned once, not once per device
- virtio and vhost now support VIRTIO_F_NOTIFICATION_DATA
- cxl gained DCD emulation support
- pvpanic gained shutdown support
- beginning of patchset for Generic Port Affinity Structure
- s3 support
- friendlier error messages when boot fails on some illegal configs
- for vhost-user, VHOST_USER_SET_LOG_BASE is now only sent once
- part of vhost-user support for any POSIX system -
not yet enabled due to qtest failures
- sr-iov VF setup code has been reworked significantly
- new tests, particularly for risc-v ACPI
- bugfixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmaF068PHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp+DMIAMC//mBXIZlPprfhb5cuZklxYi31Acgu5TUr
# njqjCkN+mFhXXZuc3B67xmrQ066IEPtsbzCjSnzuU41YK4tjvO1g+LgYJBv41G16
# va2k8vFM5pdvRA+UC9li1CCIPxiEcszxOdzZemj3szWLVLLUmwsc5OZLWWeFA5m8
# vXrrT9miODUz3z8/Xn/TVpxnmD6glKYIRK/IJRzzC4Qqqwb5H3ji/BJV27cDUtdC
# w6ns5RYIj5j4uAiG8wQNDggA1bMsTxFxThRDUwxlxaIwAcexrf1oRnxGRePA7PVG
# BXrt5yodrZYR2sR6svmOOIF3wPMUDKdlAItTcEgYyxaVo5rAdpc=
# =p9h4
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 03 Jul 2024 03:41:51 PM PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (85 commits)
hw/pci: Replace -1 with UINT32_MAX for romsize
pcie_sriov: Register VFs after migration
pcie_sriov: Remove num_vfs from PCIESriovPF
pcie_sriov: Release VFs failed to realize
pcie_sriov: Reuse SR-IOV VF device instances
pcie_sriov: Ensure VF function number does not overflow
pcie_sriov: Do not manually unrealize
hw/ppc/spapr_pci: Do not reject VFs created after a PF
hw/ppc/spapr_pci: Do not create DT for disabled PCI device
hw/pci: Rename has_power to enabled
virtio-iommu: Clear IOMMUDevice when VFIO device is unplugged
virtio: remove virtio_tswap16s() call in vring_packed_event_read()
hw/cxl/events: Mark cxl-add-dynamic-capacity and cxl-release-dynamic-capcity unstable
hw/cxl/events: Improve QMP interfaces and documentation for add/release dynamic capacity.
tests/data/acpi/rebuild-expected-aml.sh: Add RISC-V
pc-bios/meson.build: Add support for RISC-V in unpack_edk2_blobs
meson.build: Add RISC-V to the edk2-target list
tests/data/acpi/virt: Move ARM64 ACPI tables under aarch64/${machine} path
tests/data/acpi: Move x86 ACPI tables under x86/${machine} path
tests/qtest/bios-tables-test.c: Set "arch" for x86 tests
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A PF may automatically create VFs and the PF may be function 0.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240627-reuse-v10-3-7ca0b8ed3d9f@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Disabled means it is a disabled SR-IOV VF or it is powered off, and
hidden from the guest.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240627-reuse-v10-2-7ca0b8ed3d9f@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The automatic deprecation mechanism introduced in the preceeding patches
will mark every spapr machine upto and including 2.12 as deprecated. As
such we can revert the manually added deprecation which was a subset:
commit 1392617d35
Author: Cédric Le Goater <clg@kaod.org>
Date: Tue Jan 23 16:37:02 2024 +1000
spapr: Tag pseries-2.1 - 2.11 machines as deprecated
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240620165742.1711389-13-berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This calls the MACHINE_VER_DELETION() macro in the machine type
registration method, so that when a versioned machine type reaches
the end of its life, it is no longer registered with QOM and thus
cannot be used.
The actual definition of the machine type should be deleted at
this point, but experience shows that can easily be forgotten.
By skipping registration the manual code deletion task can be
done at any later date.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240620165742.1711389-12-berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This calls the MACHINE_VER_DEPRECATION() macro in the definition of
all machine type classes which support versioning. This ensures
that they will automatically get deprecation info set when they
reach the appropriate point in their lifecycle.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240620165742.1711389-11-berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This changes the DEFINE_SPAPR_MACHINE macro to use the common
helpers for constructing versioned symbol names and strings,
bringing greater consistency across targets.
The added benefit is that it avoids the need to repeat the
version number twice in two different formats in the calls
to DEFINE_SPAPR_MACHINE.
A DEFINE_SPAPR_MACHINE_AS_LATEST helper is added so that it
is not required to pass 'false' for every single historical
machine type.
Due to the odd-ball '2.12-sxxm' machine type version, this
commit introduces a DEFINE_SPAPR_MACHINE_TAGGED helper to
allow defining of "tagged" machine types which have a string
suffix.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240620165742.1711389-5-berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This helper routine uses the machine definition, sockets, cores and
threads, to loop on all CPUs of the machine. Replace CPU_FOREACH()
with it.
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240424093048.180966-1-clg@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Replace Monitor API by HumanReadableText one (see commit f2de406f29
"docs/devel: document expectations for QAPI data modelling for QMP"
for rationale).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20240610063518.50680-2-philmd@linaro.org>
