NICs defined with -net nic are for board initialization to wire up.
Board code examines nd_table[] to find them, and creates devices with
their qdev NIC properties set accordingly.
Except "allwinner-a10" goes on a fishing expedition for NIC
configuration instead of exposing the usual NIC properties for board
code to set: it uses nd_table[0] in its instance_init() method.
Picking up the first -net nic option's configuration that way works
when the device is created by board code. But it's inappropriate for
-device and device_add. Not only is it inconsistent with how the
other block device models work (they get their configuration from
properties "mac", "vlan", "netdev"), it breaks when nd_table[0] has
been picked up by the board or a previous -device / device_add
already.
Example:
$ qemu-system-arm -S -M cubieboard -device allwinner-a10
qemu-system-arm: -device allwinner-a10: Property 'allwinner-emac.netdev' can't take value 'hub0port0', it's in use
Aborted (core dumped)
It also breaks in other entertaining ways:
$ qemu-system-arm -M highbank -device allwinner-a10
qemu-system-arm: -device allwinner-a10: Unsupported NIC model: xgmac
$ qemu-system-arm -M highbank -net nic,model=allwinner-emac -device allwinner-a10
qemu-system-arm: Unsupported NIC model: allwinner-emac
Mark the mistake with a FIXME comment.
Cc: Li Guang <lig.fnst@cn.fujitsu.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Character devices defined with -serial and -parallel are for board
initialization to wire up. Board code examines serial_hds[] and
parallel_hds[] to find them, and creates devices with their qdev
chardev properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a chardev property for board code to set: they use
serial_hds[] (often via qemu_char_get_next_serial()) or parallel_hds[]
in their realize() or init() method to connect to a backend.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is it inconsistent with how the other characrer device models
work (they connect to a backend explicitly identified by a "chardev"
property), it breaks when the backend has been picked up by the board
or a previous -device / device_add already.
Example:
$ qemu-system-ppc64 -M bamboo -S -device i82378 -device pc87312 -device pc87312
qemu-system-ppc64: -device pc87312: Property 'isa-parallel.chardev' can't take value 'parallel0', it's in use
Mark them with suitable FIXME comments.
Cc: Li Guang <lig.fnst@cn.fujitsu.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Drives defined with if!=none are for board initialization to wire up.
Board code calls drive_get() or similar to find them, and creates
devices with their qdev drive properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a drive property for board code to set: they call
driver_get() or drive_get_next() in their realize() or init() method
to implicitly connect to the "next" backend with a certain interface
type.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is this inconsistent with how the other block device models work
(they connect to a backend explicitly identified by a "drive"
property), it breaks when the "next" backend has been picked up by the
board already.
Example:
$ qemu-system-arm -S -M connex -pflash flash.img -device ssi-sd
Aborted (core dumped)
Mark them with suitable FIXME comments.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This is a continuation of the work started in commit 565f65d27:
"error: Use error_report_err() where appropriate"
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This allows to use the SD card emulation of the board: Forward the
signals from the pl181 top the CP control register emulation, report the
current state via CP_INTREG, deliver CARDIN IRQ to the secondary
interrupt controller and also support clearing that line via CP_INTREG.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-id: c55d9fb28d19ec83625cb0074b3b6f2e5958caf6.1426004843.git.jan.kiszka@siemens.com
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the stm32f205 SoC. This will be used by the
Netduino 2 to create a machine.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 48d509747a1ea0d8a7d5480560495e679990f9d2.1424175342.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The recently introduced feature that allows 32 bit guests to be
executed under KVM on a 64-bit host incorrectly handles the case
where more than 1 cpu is specified using '-smp N'
For instance, this invocation of qemu
qemu-system-aarch64 -M virt -cpu cortex-a57,aarch64=off -smp 2
produces the following error
qemu-system-aarch64: Expected key=value format, found aarch64
which is caused by the destructive parsing performed by
cpu_common_parse_features(), resulting in subsequent attempts
to parse the CPU option string (for each additional CPU) to fail.
So duplicate the string before parsing it, and free it directly
afterwards.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1425402380-10488-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity/sparse fix for iscsi driver
- RCU fallout: fix -daemonize and s390x system emulation
- KVM: kvm_stat improvements and new man page
- x86: SYSRET fix for VxWorks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJU/sUFAAoJEL/70l94x66D1JwIAJ28Lan2DQwi+xHvNxF8zW6n
v7eMc04/fepuon0TYmUZC3qbqc00sccEQZQ+yAAauT9epZ/kdSDudDOzG+3F4MuQ
/X3crXw2/jrhtWedGq49vFCONX4MKoaoudqK8kOFMe1ImQgkOYeAzOoqeFXyHsFh
jINlKTJZB6oKzrZ+SYryY14cO7pvGaIhyqaCC+6GcVihTjm9Yq13lP1lFj7LsVRV
aGfd6xH9RSV/mwzvZwD4i3cUWSUaV/wY0NDhAEzDPCUcxX0/nAj3XF1YeJUF30Qd
ETaCLo/Nxq2R6POK3c/Zm/FRLvjzZ2caD+q1LcwB/bCYdc2lJ1JDxE/hr48ANv0=
=OWXY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- scsi: improvements to error reporting and conversion to realize,
Coverity/sparse fix for iscsi driver
- RCU fallout: fix -daemonize and s390x system emulation
- KVM: kvm_stat improvements and new man page
- x86: SYSRET fix for VxWorks
# gpg: Signature made Tue Mar 10 10:18:45 2015 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
x86: fix SS selector in SYSRET
scsi: Convert remaining PCI HBAs to realize()
scsi: Improve error reporting for invalid drive property
hw: Propagate errors through qdev_prop_set_drive()
scsi: Clean up duplicated error in legacy if=scsi code
cpus: initialize cpu->memory_dispatch
rcu: handle forks safely
qemu-thread: do not use PTHREAD_MUTEX_ERRORCHECK
kvm_stat: add kvm_stat.1 man page
kvm_stat: add column headers to text UI
iscsi: Fix check for username
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Three kinds of callers:
1. On failure, report the error and abort
Passing &error_abort does the job. No functional change.
2. On failure, report the error and exit()
This is qdev_prop_set_drive_nofail(). Error reporting moves from
qdev_prop_set_drive() to its caller. Because hiding away the error
in the monitor right before exit() isn't helpful, replace
qerror_report_err() by error_report_err(). Shouldn't make a
difference, because qdev_prop_set_drive_nofail() should never be
used in QMP context.
3. On failure, report the error and recover
This is usb_msd_init() and scsi_bus_legacy_add_drive(). Error
reporting and freeing the error object moves from
qdev_prop_set_drive() to its callers.
Because usb_msd_init() can't run in QMP context, replace
qerror_report_err() by error_report_err() there.
No functional change.
scsi_bus_legacy_add_drive() calling qerror_report_err() is of
course inappropriate, but this commit merely makes it more obvious.
The next one will clean it up.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-Id: <1425925048-15482-3-git-send-email-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Added machvirt parsing of feature keywords added to the -cpu command line
option. Parsing occurs during machine initialization.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1423736974-14254-3-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we have a working "generic" PCIe host bridge driver, we can plug
it into ARM's virt machine to always have PCIe available to normal ARM VMs.
I've successfully managed to expose a Bochs VGA device, XHCI and an e1000
into an AArch64 VM with this and they all lived happily ever after.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
[PMM: Squashed in fix for off-by-one error in bus-range DT property
from Laszlo Ersek <lersek@redhat.com>]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update to arm_cpu_reset() to reset into the highest available exception level
based on the set ARM features.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1422029835-4696-4-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows the board to specifiy the number of NVIC interrupt
lines when using armv7m_init.
Signed-off-by: Alistair Francis <alistair23@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 5a0b0fcc778df0340899f488053acc9493679e03.1422077994.git.alistair23@gmail.com
[PMM: removed stale FIXME comment]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch moves the memory region init code from the
armv7m_init function to the stellaris_init function
Signed-off-by: Alistair Francis <alistair23@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 4836be7e1d708554d6eb0bc639dc2fbf7dac0458.1422077994.git.alistair23@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The argument is not longer used and the implementation
uses now QOM instead of QemuOpts.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-id: 1420550957-22337-4-git-send-email-marcel@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt board already ensures mutual exclusion between -bios and -pflash
unit#0; we only need to set "bootinfo.firmware_loaded", introduced in the
previous patch, if either of those options was used to load the guest
firmware.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1419250305-31062-12-git-send-email-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the new boolean field "arm_boot_info.firmware_loaded". When this
field is set, it means that the portion of guest DRAM that the VCPU
normally starts to execute, or the pflash chip that the VCPU normally
starts to execute, has been populated by board-specific code with
full-fledged guest firmware code, before the board calls
arm_load_kernel().
Simultaneously, "arm_boot_info.firmware_loaded" guarantees that the board
code has set up the global firmware config instance, for arm_load_kernel()
to find with fw_cfg_find().
Guest kernel (-kernel) and guest firmware (-bios, -pflash) has always been
possible to specify independently on the command line. The following cases
should be considered:
nr -bios -pflash -kernel description
unit#0
-- ------- ------- ------- -------------------------------------------
1 present present absent Board code rejects this case, -bios and
present present present -pflash unit#0 are exclusive. Left intact
by this patch.
2 absent absent present Traditional kernel loading, with qemu's
minimal board firmware. Left intact by this
patch.
3 absent present absent Preexistent case for booting guest firmware
present absent absent loaded with -bios or -pflash. Left intact
by this patch.
4 absent absent absent Preexistent case for not loading any
firmware or kernel up-front. Left intact by
this patch.
5 present absent present New case introduced by this patch: kernel
absent present present image is passed to externally loaded
firmware in unmodified form, using fw_cfg.
An easy way to see that this patch doesn't interfere with existing cases
is to realize that "info->firmware_loaded" is constant zero at this point.
Which makes the "outer" condition unchanged, and the "inner" condition
(with the fw_cfg-related code) dead.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1419250305-31062-11-git-send-email-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
fw_cfg already supports exposure over MMIO (used in ppc/mac_newworld.c,
ppc/mac_oldworld.c, sparc/sun4m.c); we can easily add it to the "virt"
board.
Because MMIO access is slow on ARM KVM, we enable the guest, with
fw_cfg_init_mem_wide(), to transfer up to 8 bytes with a single access.
This has been measured to speed up transfers up to 7.5-fold, relative to
single byte data access, on both ARM KVM and x86_64 TCG.
The MMIO register block of fw_cfg is advertized in the device tree. As
base address we pick 0x09020000, which conforms to the comment preceding
"a15memmap": it falls in the miscellaneous device I/O range 128MB..256MB,
and it is aligned at 64KB. The DTB properties follow the documentation in
the Linux source file "Documentation/devicetree/bindings/arm/fw-cfg.txt".
fw_cfg automatically exports a number of files to the guest; for example,
"bootorder" (see fw_cfg_machine_reset()).
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1419250305-31062-9-git-send-email-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Disables the CPU ARM_FEATURE_EL3 featuere on machine models that can be
configured to use Cortex-A9, Cortex-A15, and ARM1176 but don't officially
support EL3. This preserves backwards compatibility.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-15-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit changes the integratorcp and versatilepb CPU initialization from
using the generic ARM cpu_arm_init function to doing it inline. This is
necessary in order to allow CPU configuration changes to occur between CPU
instance initialization and realization. Specifically, this change is in
preparation for disabling CPU EL3 support.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-14-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds setting of the CPU has_el3 property based on the virt machine
secure state property during initialization. This enables/disables EL3
state during start-up. Changes include adding an additional secure state
boolean during virt CPU initialization. Also disables the ARM secure boot
by default.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1418684992-8996-13-git-send-email-greg.bellows@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds setting of the CPU has_el3 property based on the vexpress machine
secure state property during initialization. This enables/disables EL3
state during start-up. Changes include adding an additional secure state
boolean during vexpress CPU initialization. Also enables the ARM secure boot
by default.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1418684992-8996-12-git-send-email-greg.bellows@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds the secure_boot boolean field to the arm_boot_info descriptor. This
fields is used to indicate whether Linux should boot into secure or non-secure
state if the ARM EL3 feature is enabled. The default is to leave the CPU in an
unaltered reset state. On EL3 enabled systems, the reset state is secure and
can be overridden by setting the added field to false.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-11-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add "secure" virt machine specific property to allow override of the
default secure state configuration. By default, when using the QEMU
-kernel command line argument, virt machines boot into NS/SVC. When using
the QEMU -bios command line argument, virt machines boot into S/SVC.
The secure state can be changed from the default specifying the secure
state as a machine property. For example, the below command line would disable
security extensions on a -kernel Linux boot:
aarch64-softmmu/qemu-system-aarch64
-machine type=virt,secure=off
-kernel ...
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-8-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch virt qemu machine support to use the newer object type, class, and
instance model. Added virt TypeInfo with static registration along with virt
specific class and machine structs. Also added virt class initialization
method.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-7-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the Vexpress daughterboard initialization method to take a vexpress
machine state pointer instead of the daughterboard struct pointer. The machine
state now contains the daughterboard pointer.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-6-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add "secure" Vexpress machine specific property to allow override of the
default secure state configuration. By default, when using the QEMU
-kernel command line argument, Vexpress machines boot into NS/SVC. When using
the QEMU -bios command line argument, Vexpress machines boot into S/SVC.
The secure state can be changed from the default specifying the secure
state as a machine property. For example, the below command line would disable
security extensions on a -kernel Linux boot:
aarch64-softmmu/qemu-system-aarch64
-machine type=vexpress-a15,secure=off
-kernel ...
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-5-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switched the Vexpress machine initialization to use the common function with
the machine pointer to board info.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-4-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add Vexpress machine objects for the the Cortex A9 & A15 variants. The older
style QEMUMachine types were replaced with dedicated TypeInfo objects. The new
objects include dedicated class init functions that currently ustilze dedicated
machine init methods. The previous qemu_register_machine calls were replaced
with the newer type_register_status calls.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-3-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds base Vexpress class and machine objects and infrastructure. This is in
preparation for switching to the full QEMU object model. The base vexpress
infrastructure is intended to handle common vexpress details.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-2-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity reports the 'size' may be used uninitialized, but that can't happen,
because the caller has checked "if (binfo->dtb_filename || binfo->get_dtb)"
before call 'load_dtb'.
Here we simply remove the 'if (binfo->get_dtb)' to satisfy coverity.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Message-id: 1416826240-12368-1-git-send-email-zhang.zhanghailiang@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Variable 'ram_lo' is allocated unconditionally, but used only in some cases.
When it is unused pointer will be lost at function exit, resulting in a
memory leak. Allocate memory for 'ram_lo' only if it is needed.
Valgrind output:
==16879== 240 bytes in 1 blocks are definitely lost in loss record 6,033 of 7,018
==16879== at 0x4C2AB80: malloc (in /usr/lib/valgrind/vgpreload_memcheck-amd64-linux.so)
==16879== by 0x33D2CE: malloc_and_trace (vl.c:2804)
==16879== by 0x509E610: g_malloc (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4000.0)
==16879== by 0x288836: realview_init (realview.c:55)
==16879== by 0x28988C: realview_pb_a8_init (realview.c:375)
==16879== by 0x341426: main (vl.c:4413)
Signed-off-by: Nikita Belov <zodiac@ispras.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
DACR has a secure and a non-secure instance. Adds definition for DACR32_EL2.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-19-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds secure and non-secure bank register suport for TTBR0 and TTBR1.
Changes include adding secure and non-secure instances of ttbr0 and ttbr1 as
well as a CP register definition for TTBR0_EL3. Added a union containing
both EL based array fields and secure and non-secure fields mapped to them.
Updated accesses to use A32_BANKED_CURRENT_REG_GET macro.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-17-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ePAPR 1.1 defines the stdout-path property, making the os-specific
linux,stdout-path property redundant. Change the DT setup for ARM virt
to use the generic property - supported by Linux since 3.15.
The old QEMU behaviour was not present in any released version of
QEMU, and was only added to QEMU after the kernel changed, so
this should not break any existing setups.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
[PMM: add note to commit about the old behaviour never hving been
in a released version of QEMU]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Such address translation is needed when load address recorded in uImage
is a virtual address. When the actual load address is requested, return
untranslated address: user that needs the translated address can always
apply translation function to it and those that need it untranslated
don't need to do the inverse translation.
Add translation function pointer and its parameter to uimage_load
prototype. Update all existing users.
No user-visible functional changes.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Now that we have PSCI emulation, enable it for the virt platform.
This simplifies the virt machine a bit now that PSCI no longer
needs to be a KVM only feature.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-8-git-send-email-peter.maydell@linaro.org
Move the registering of CPU reset handlers to before the point where
we leave the function in the -bios (not -kernel) case, so CPU reset
works correctly with -bios as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
check if the first cpu is an armv8 cpu, and if so, put
arm,armv8-timer in the compatible string list.
Note that due to this check, this patch moves the creation
of the timer fdt node to after the cpu creation loop.
Signed-off-by: Claudio Fontana <claudio.fontana@huawei.com>
Message-id: 1411736960-24206-1-git-send-email-hw.claudio@gmail.com
[PMM: updated to list arm,armv8-timer first]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
