VFIO migration is not compatible with postcopy migration. A VFIO device
in the destination can't handle page faults for pages that have not been
sent yet.
Doing such migration will cause the VM to crash in the destination:
qemu-system-x86_64: VFIO_MAP_DMA failed: Bad address
qemu-system-x86_64: vfio_dma_map(0x55a28c7659d0, 0xc0000, 0xb000, 0x7f1b11a00000) = -14 (Bad address)
qemu: hardware error: vfio: DMA mapping failed, unable to continue
To prevent this, block VFIO migration with postcopy migration.
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Tested-by: Yanghang Liu <yanghliu@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
If a device with enable-migration=on is added and it causes a migration
blocker, adding the device should fail with a proper error.
This is not the case with multiple device migration blocker when the
blocker already exists. If the blocker already exists and a device with
enable-migration=on is added which causes a migration blocker, adding
the device will succeed.
Fix it by failing adding the device in such case.
Fixes: 8bbcb64a71 ("vfio/migration: Make VFIO migration non-experimental")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Now that P2P support has been added to VFIO migration, allow migration
of multiple devices if all of them support P2P migration.
Single device migration is allowed regardless of P2P migration support.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
VFIO migration uAPI defines an optional intermediate P2P quiescent
state. While in the P2P quiescent state, P2P DMA transactions cannot be
initiated by the device, but the device can respond to incoming ones.
Additionally, all outstanding P2P transactions are guaranteed to have
been completed by the time the device enters this state.
The purpose of this state is to support migration of multiple devices
that might do P2P transactions between themselves.
Add support for P2P migration by transitioning all the devices to the
P2P quiescent state before stopping or starting the devices. Use the new
VMChangeStateHandler prepare_cb to achieve that behavior.
This will allow migration of multiple VFIO devices if all of them
support P2P migration.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move the PRE_COPY and RUNNING state checks to helper functions.
This is in preparation for adding P2P VFIO migration support, where
these helpers will also test for PRE_COPY_P2P and RUNNING_P2P states.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Add qdev_add_vm_change_state_handler_full() variant that allows setting
a prepare callback in addition to the main callback.
This will facilitate adding P2P support for VFIO migration in the
following patches.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Changing the device state from STOP_COPY to STOP can take time as the
device may need to free resources and do other operations as part of the
transition. Currently, this is done in vfio_save_complete_precopy() and
therefore it is counted in the migration downtime.
To avoid this, change the device state from STOP_COPY to STOP in
vfio_save_cleanup(), which is called after migration has completed and
thus is not part of migration downtime.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Commit 6df0b37e2ab breaks a --enable-debug build in a non-KVM
environment with the following error:
/usr/bin/ld: libqemu-riscv64-softmmu.fa.p/hw_intc_riscv_aplic.c.o: in function `riscv_kvm_aplic_request':
./qemu/build/../hw/intc/riscv_aplic.c:486: undefined reference to `kvm_set_irq'
collect2: error: ld returned 1 exit status
This happens because the debug build will poke into the
'if (is_kvm_aia(aplic->msimode))' block and fail to find a reference to
the KVM only function riscv_kvm_aplic_request().
There are multiple solutions to fix this. We'll go with the same
solution from the previous patch, i.e. add a kvm_enabled() conditional
to filter out the block. But there's a catch: riscv_kvm_aplic_request()
is a local function that would end up being used if the compiler crops
the block, and this won't work. Quoting Richard Henderson's explanation
in [1]:
"(...) the compiler won't eliminate entire unused functions with -O0"
We'll solve it by moving riscv_kvm_aplic_request() to kvm.c and add its
declaration in kvm_riscv.h, where all other KVM specific public
functions are already declared. Other archs handles KVM specific code in
this manner and we expect to do the same from now on.
[1] https://lore.kernel.org/qemu-riscv/d2f1ad02-eb03-138f-9d08-db676deeed05@linaro.org/
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230830133503.711138-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
A build with --enable-debug and without KVM will fail as follows:
/usr/bin/ld: libqemu-riscv64-softmmu.fa.p/hw_riscv_virt.c.o: in function `virt_machine_init':
./qemu/build/../hw/riscv/virt.c:1465: undefined reference to `kvm_riscv_aia_create'
This happens because the code block with "if virt_use_kvm_aia(s)" isn't
being ignored by the debug build, resulting in an undefined reference to
a KVM only function.
Add a 'kvm_enabled()' conditional together with virt_use_kvm_aia() will
make the compiler crop the kvm_riscv_aia_create() call entirely from a
non-KVM build. Note that adding the 'kvm_enabled()' conditional inside
virt_use_kvm_aia() won't fix the build because this function would need
to be inlined multiple times to make the compiler zero out the entire
block.
While we're at it, use kvm_enabled() in all instances where
virt_use_kvm_aia() is checked to allow the compiler to elide these other
kvm-only instances as well.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Fixes: dbdb99948e ("target/riscv: select KVM AIA in riscv virt machine")
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230830133503.711138-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On a dtb dumped from the virt machine, dt-validate complains:
soc: pmu: {'riscv,event-to-mhpmcounters': [[1, 1, 524281], [2, 2, 524284], [65561, 65561, 524280], [65563, 65563, 524280], [65569, 65569, 524280]], 'compatible': ['riscv,pmu']} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
That's pretty cryptic, but running the dtb back through dtc produces
something a lot more reasonable:
Warning (simple_bus_reg): /soc/pmu: missing or empty reg/ranges property
Moving the riscv,pmu node out of the soc bus solves the problem.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230727-groom-decline-2c57ce42841c@spud>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Select KVM AIA when the host kernel has in-kernel AIA chip support.
Since KVM AIA only has one APLIC instance, we map the QEMU APLIC
devices to KVM APLIC.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230727102439.22554-6-yongxuan.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
KVM AIA can't emulate APLIC only. When "aia=aplic" parameter is passed,
APLIC devices is emulated by QEMU. For "aia=aplic-imsic", remove the
mmio operations of APLIC when using KVM AIA and send wired interrupt
signal via KVM_IRQ_LINE API.
After KVM AIA enabled, MSI messages are delivered by KVM_SIGNAL_MSI API
when the IMSICs receive mmio write requests.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230727102439.22554-5-yongxuan.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In this patch, we create the APLIC and IMSIC FDT helper functions and
remove M mode AIA devices when using KVM acceleration.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230727102439.22554-2-yongxuan.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The variables whose values are given by cpu_riscv_read_rtc() should be named
"rtc". The variables whose value are given by cpu_riscv_read_rtc_raw()
should be named "rtc_r".
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230728082502.26439-2-jason.chien@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When writing the upper mtime, we should keep the original lower mtime
whose value is given by cpu_riscv_read_rtc() instead of
cpu_riscv_read_rtc_raw(). The same logic applies to writes to lower mtime.
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230728082502.26439-1-jason.chien@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Values that have been read via cpu_physical_memory_read() from the
guest's memory have to be swapped in case the host endianess differs
from the guest.
Fixes: a6e13e31d5 ("riscv_htif: Support console output via proxy syscall")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230721094720.902454-3-thuth@redhat.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The character that should be printed is stored in the 64 bit "payload"
variable. The code currently tries to print it by taking the address
of the variable and passing this pointer to qemu_chr_fe_write(). However,
this only works on little endian hosts where the least significant bits
are stored on the lowest address. To do this in a portable way, we have
to store the value in an uint8_t variable instead.
Fixes: 5033606780 ("RISC-V HTIF Console")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230721094720.902454-2-thuth@redhat.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The cortex-a710 is a first generation ARMv9.0-A processor.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230831232441.66020-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the Configuration Frame controller (CFRAME_REG) and the
Configuration Frame broadcast controller (CFRAME_BCAST_REG) to the
Versal machine.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-9-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the Configuration Frame Unit (CFU_APB, CFU_FDRO and CFU_SFR) to
the Versal machine.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Acked-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-8-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame broadcast
controller (CFRAME_BCAST_REG).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-7-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame controller
(CFRAME_REG).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20230831165701.2016397-6-francisco.iglesias@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame Unit's Single
Frame Read port (CFU_SFR).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-5-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame Unit's data out
port (CFU_FDRO).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-4-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of the software programming interface (CFU_APB) of
Xilinx Versal's Configuration Frame Unit.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-3-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the Xilinx Configuration Frame Interface (CFI) for transmitting
CFI data packets between the Xilinx Configuration Frame Unit models
(CFU_APB, CFU_FDRO and CFU_SFR), the Xilinx CFRAME controller (CFRAME_REG)
and the Xilinx CFRAME broadcast controller (CFRAME_BCAST_REG) models (when
emulating bitstream programming and readback).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Acked-by: Edgar E. Iglesias <edgar@zeroasic.com>
Message-id: 20230831165701.2016397-2-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix when using GCC v11.4 (Ubuntu 11.4.0-1ubuntu1~22.04) with CFLAGS=-Og:
[4/6] Compiling C object libcommon.fa.p/hw_intc_arm_gicv3_its.c.o
FAILED: libcommon.fa.p/hw_intc_arm_gicv3_its.c.o
inlined from ‘lookup_vte’ at hw/intc/arm_gicv3_its.c:453:9,
inlined from ‘vmovp_callback’ at hw/intc/arm_gicv3_its.c:1039:14:
hw/intc/arm_gicv3_its.c:347:9: error: ‘vte.rdbase’ may be used uninitialized [-Werror=maybe-uninitialized]
347 | trace_gicv3_its_vte_read(vpeid, vte->valid, vte->vptsize,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
348 | vte->vptaddr, vte->rdbase);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_its.c: In function ‘vmovp_callback’:
hw/intc/arm_gicv3_its.c:1036:13: note: ‘vte’ declared here
1036 | VTEntry vte;
| ^~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230831131348.69032-1-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio_load() as a whole should run in coroutine context because it
reads from the migration stream and we don't want this to block.
However, it calls virtio_set_features_nocheck() and devices don't
expect their .set_features callback to run in a coroutine and therefore
call functions that may not be called in coroutine context. To fix this,
drop out of coroutine context for calling virtio_set_features_nocheck().
Without this fix, the following crash was reported:
#0 __pthread_kill_implementation (threadid=<optimized out>, signo=signo@entry=6, no_tid=no_tid@entry=0) at pthread_kill.c:44
#1 0x00007efc738c05d3 in __pthread_kill_internal (signo=6, threadid=<optimized out>) at pthread_kill.c:78
#2 0x00007efc73873d26 in __GI_raise (sig=sig@entry=6) at ../sysdeps/posix/raise.c:26
#3 0x00007efc738477f3 in __GI_abort () at abort.c:79
#4 0x00007efc7384771b in __assert_fail_base (fmt=0x7efc739dbcb8 "", assertion=assertion@entry=0x560aebfbf5cf "!qemu_in_coroutine()",
file=file@entry=0x560aebfcd2d4 "../block/graph-lock.c", line=line@entry=275, function=function@entry=0x560aebfcd34d "void bdrv_graph_rdlock_main_loop(void)") at assert.c:92
#5 0x00007efc7386ccc6 in __assert_fail (assertion=0x560aebfbf5cf "!qemu_in_coroutine()", file=0x560aebfcd2d4 "../block/graph-lock.c", line=275,
function=0x560aebfcd34d "void bdrv_graph_rdlock_main_loop(void)") at assert.c:101
#6 0x0000560aebcd8dd6 in bdrv_register_buf ()
#7 0x0000560aeb97ed97 in ram_block_added.llvm ()
#8 0x0000560aebb8303f in ram_block_add.llvm ()
#9 0x0000560aebb834fa in qemu_ram_alloc_internal.llvm ()
#10 0x0000560aebb2ac98 in vfio_region_mmap ()
#11 0x0000560aebb3ea0f in vfio_bars_register ()
#12 0x0000560aebb3c628 in vfio_realize ()
#13 0x0000560aeb90f0c2 in pci_qdev_realize ()
#14 0x0000560aebc40305 in device_set_realized ()
#15 0x0000560aebc48e07 in property_set_bool.llvm ()
#16 0x0000560aebc46582 in object_property_set ()
#17 0x0000560aebc4cd58 in object_property_set_qobject ()
#18 0x0000560aebc46ba7 in object_property_set_bool ()
#19 0x0000560aeb98b3ca in qdev_device_add_from_qdict ()
#20 0x0000560aebb1fbaf in virtio_net_set_features ()
#21 0x0000560aebb46b51 in virtio_set_features_nocheck ()
#22 0x0000560aebb47107 in virtio_load ()
#23 0x0000560aeb9ae7ce in vmstate_load_state ()
#24 0x0000560aeb9d2ee9 in qemu_loadvm_state_main ()
#25 0x0000560aeb9d45e1 in qemu_loadvm_state ()
#26 0x0000560aeb9bc32c in process_incoming_migration_co.llvm ()
#27 0x0000560aebeace56 in coroutine_trampoline.llvm ()
Cc: qemu-stable@nongnu.org
Buglink: https://issues.redhat.com/browse/RHEL-832
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20230905145002.46391-3-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The assert() that checks for valid MTU sizes can be triggered by
the guest (e.g. with the reproducer code from the bug ticket
https://gitlab.com/qemu-project/qemu/-/issues/517 ). Let's avoid
this problem by simply logging the error and refusing to activate
the device instead.
Fixes: d05dcd94ae ("net: vmxnet3: validate configuration values during activate")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
[Mjt: change format specifier from %d to %u for uint32_t argument]
tcet->mig_table is copied from tcet->table, which in turn is created
in spapr_tce_alloc_table() using g_new0().
Use g_free() instead of free() to deallocate it.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
[Mjt: fix commit comments]
TARGET_BIG_ENDIAN is *always* defined, either as 0 for little endian
targets or as 1 for big endian targets. So we can use this as a value
directly in places that need such a 0 or 1 for some reason, instead
of taking a detour through an additional local variable or something
similar.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The file has been converted to .rst a while ago - make sure that the
references in the trace-events files are pointing to the right location
now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit adds support for ufs logical unit.
The LU handles processing for the SCSI command,
unit descriptor query request.
This commit enables the UFS device to process
IO requests.
Signed-off-by: Jeuk Kim <jeuk20.kim@samsung.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: beacc504376ab6a14b1a3830bb3c69382cf6aebc.1693980783.git.jeuk20.kim@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This commit makes the UFS device support query
and nop out transfer requests.
The next patch would be support for UFS logical
unit and scsi command transfer request.
Signed-off-by: Jeuk Kim <jeuk20.kim@samsung.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: ff7a5f0fd26761936a553ffb89d3df0ba62844e9.1693980783.git.jeuk20.kim@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Universal Flash Storage (UFS) is a high-performance mass storage device
with a serial interface. It is primarily used as a high-performance
data storage device for embedded applications.
This commit contains code for UFS device to be recognized
as a UFS PCI device.
Patches to handle UFS logical unit and Transfer Request will follow.
Signed-off-by: Jeuk Kim <jeuk20.kim@samsung.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 10232660d462ee5cd10cf673f1a9a1205fc8276c.1693980783.git.jeuk20.kim@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* target/i386: fix BQL handling of the legacy FERR interrupts
* target/i386: fix memory operand size for CVTPS2PD
* target/i386: Add support for AMX-COMPLEX in CPUID enumeration
* compile plugins on Darwin
* configure and meson cleanups
* drop mkvenv support for Python 3.7 and Debian10
* add wrap file for libblkio
* tweak KVM stubs
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT5t6UUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMmjwf+MpvVuq+nn+3PqGUXgnzJx5ccA5ne
O9Xy8+1GdlQPzBw/tPovxXDSKn3HQtBfxObn2CCE1tu/4uHWpBA1Vksn++NHdUf2
P0yoHxGskJu5iYYTtIcNw5cH2i+AizdiXuEjhfNjqD5Y234cFoHnUApt9e3zBvVO
cwGD7WpPuSb4g38hHkV6nKcx72o7b4ejDToqUVZJ2N+RkddSqB03fSdrOru0hR7x
V+lay0DYdFszNDFm05LJzfDbcrHuSryGA91wtty7Fzj6QhR/HBHQCUZJxMB5PI7F
Zy4Zdpu60zxtSxUqeKgIi7UhNFgMcax2Hf9QEqdc/B4ARoBbboh4q4u8kQ==
=dH7/
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* only build util/async-teardown.c when system build is requested
* target/i386: fix BQL handling of the legacy FERR interrupts
* target/i386: fix memory operand size for CVTPS2PD
* target/i386: Add support for AMX-COMPLEX in CPUID enumeration
* compile plugins on Darwin
* configure and meson cleanups
* drop mkvenv support for Python 3.7 and Debian10
* add wrap file for libblkio
* tweak KVM stubs
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT5t6UUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroMmjwf+MpvVuq+nn+3PqGUXgnzJx5ccA5ne
# O9Xy8+1GdlQPzBw/tPovxXDSKn3HQtBfxObn2CCE1tu/4uHWpBA1Vksn++NHdUf2
# P0yoHxGskJu5iYYTtIcNw5cH2i+AizdiXuEjhfNjqD5Y234cFoHnUApt9e3zBvVO
# cwGD7WpPuSb4g38hHkV6nKcx72o7b4ejDToqUVZJ2N+RkddSqB03fSdrOru0hR7x
# V+lay0DYdFszNDFm05LJzfDbcrHuSryGA91wtty7Fzj6QhR/HBHQCUZJxMB5PI7F
# Zy4Zdpu60zxtSxUqeKgIi7UhNFgMcax2Hf9QEqdc/B4ARoBbboh4q4u8kQ==
# =dH7/
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 07 Sep 2023 07:44:37 EDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (51 commits)
docs/system/replay: do not show removed command line option
subprojects: add wrap file for libblkio
sysemu/kvm: Restrict kvm_pc_setup_irq_routing() to x86 targets
sysemu/kvm: Restrict kvm_has_pit_state2() to x86 targets
sysemu/kvm: Restrict kvm_get_apic_state() to x86 targets
sysemu/kvm: Restrict kvm_arch_get_supported_cpuid/msr() to x86 targets
target/i386: Restrict declarations specific to CONFIG_KVM
target/i386: Allow elision of kvm_hv_vpindex_settable()
target/i386: Allow elision of kvm_enable_x2apic()
target/i386: Remove unused KVM stubs
target/i386/cpu-sysemu: Inline kvm_apic_in_kernel()
target/i386/helper: Restrict KVM declarations to system emulation
hw/i386/fw_cfg: Include missing 'cpu.h' header
hw/i386/pc: Include missing 'cpu.h' header
hw/i386/pc: Include missing 'sysemu/tcg.h' header
Revert "mkvenv: work around broken pip installations on Debian 10"
mkvenv: assume presence of importlib.metadata
Python: Drop support for Python 3.7
configure: remove dead code
meson: list leftover CONFIG_* symbols
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* debug facility improvements
* timebase and decrementer fixes
* record-replay fixes
* TCG fixes
* XIVE model improvements for multichip
-----BEGIN PGP SIGNATURE-----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=BUg6
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20230906' of https://github.com/legoater/qemu into staging
ppc queue :
* debug facility improvements
* timebase and decrementer fixes
* record-replay fixes
* TCG fixes
* XIVE model improvements for multichip
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmT4WKoACgkQUaNDx8/7
# 7KHjOg//bwENCptopnvX5XVTdGLRgBKoMWPkQhWPv4aHYz4t+bxHVWopdMU7i0aL
# hge+ZCCkMKsg2rADczbpWytAvC3vo1Pn4zZhZNQuEvYKIpiWVN6hSflmXWP/bN1I
# AGHlptKvNYKlPfGsmzZ2OZ2yItzrOwKFC/PnPSEc6dxjWfe9hEwzApxaAkOfX8wf
# C+oH8DPvFmh3PH3rI4psCn/xYtxAPW1zosBtgT7Ii1XreABMHLIfIpOmPPh1yF0d
# J7BgBdmxIvsN+syH/vh5jTtU4N/gQVorwyds9MX82Y3j0roxBVVLqH8rFjJA3Jsq
# c/g8WTi1hHiDd8G4m1JcLI1VAhsgh1KhqG9pDaSdQXhP0E4p8N/XjxOR5ro+KxM3
# Dz/Q77VoEKuat+AXg71kc68i11CninhTVSyGnjI80ISWWYvHFQ2Sv8J9U6sS/d0m
# +fo6hed7DDgfXg4OMtedF4HMmc6JAfm9eBzHUoanaoIzX0vX6vetXeMfWh6iceYW
# KNcQuUi3Pvvh/AjE36jusqTkbTleP5Yo4OKNJz4pEP4sU2wQPYU32Lo7Kg7p4WPA
# j+emWmWX4gcn9zTvm2LPYwkdgQ5HgigUJzq9i9qlMqfOOCpRwAsE7V0KxyV0NwDT
# cAAOBCdNm4t94Ni3KEING7xuDzERvJ7H2D6uRQjVsre8cMUO0QE=
# =BUg6
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 06 Sep 2023 06:47:06 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-ppc-20230906' of https://github.com/legoater/qemu: (35 commits)
ppc/xive: Add support for the PC MMIOs
ppc/xive: Handle END triggers between chips with MMIOs
ppc/xive: Introduce a new XiveRouter end_notify() handler
ppc/xive: Use address_space routines to access the machine RAM
target/ppc: Fix the order of kvm_enable judgment about kvmppc_set_interrupt()
hw/ppc/e500: fix broken snapshot replay
target/ppc: Flush inputs to zero with NJ in ppc_store_vscr
target/ppc: Fix LQ, STQ register-pair order for big-endian
tests/avocado: ppc64 reverse debugging tests for pseries and powernv
tests/avocado: reverse-debugging cope with re-executing breakpoints
tests/avocado: boot ppc64 pseries replay-record test to Linux VFS mount
spapr: Fix record-replay machine reset consuming too many events
spapr: Fix machine reset deadlock from replay-record
target/ppc: Fix timebase reset with record-replay
target/ppc: Fix CPU reservation migration for record-replay
hw/ppc: Read time only once to perform decrementer write
hw/ppc: Reset timebase facilities on machine reset
target/ppc: Migrate DECR SPR
hw/ppc: Always store the decrementer value
target/ppc: Sign-extend large decrementer to 64-bits
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
kvm_pc_setup_irq_routing() is only defined for x86 targets (in
hw/i386/kvm/apic.c). Its declaration is pointless on all
other targets.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-14-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_has_pit_state2() is only defined for x86 targets (in
target/i386/kvm/kvm.c). Its declaration is pointless on
all other targets. Have it return a boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-13-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_enabled() before kvm_hv_vpindex_settable()
to let the compiler elide its call.
kvm-stub.c is now empty, remove it.
Suggested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-9-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_enabled() before kvm_enable_x2apic() to let the compiler elide
its call. Cleanup the code by simplifying "!xen_enabled() &&
kvm_enabled()" to just "kvm_enabled()".
Suggested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-8-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
fw_cfg_build_feature_control() uses CPUID_EXT_VMX which is
defined in "target/i386/cpu.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-4-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both pc_piix.c and pc_q35.c files use CPU_VERSION_LEGACY
which is defined in "target/i386/cpu.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-3-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 6f529b7534 ("target/i386: move FERR handling
to target/i386") pc_q35_init() calls tcg_enabled() which
is declared in "sysemu/tcg.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-2-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When encountering an NCQ error, you should not write the NCQ tag to the
SError register. This is completely wrong.
The SError register has a clear definition, where each bit represents a
different error, see PxSERR definition in AHCI 1.3.1.
If we write a random value (like the NCQ tag) in SError, e.g. Linux will
read SError, and will trigger arbitrary error handling depending on the
NCQ tag that happened to be executing.
In case of success, ncq_cb() will call ncq_finish().
In case of error, ncq_cb() will call ncq_err() (which will clear
ncq_tfs->used), and then call ncq_finish(), thus using ncq_tfs->used is
sufficient to tell if finished should get set or not.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-9-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
When there is an error, we need to raise a TFES error irq, see AHCI 1.3.1,
5.3.13.1 SDB:Entry.
If ERR_STAT is set, we jump to state ERR:FatalTaskfile, which will raise
a TFES IRQ unconditionally, regardless if the I bit is set in the FIS or
not.
Thus, we should never raise a normal IRQ after having sent an error IRQ.
It is valid to signal successfully completed commands as finished in the
same SDB FIS that generates the error IRQ. The important thing is that
commands that did not complete successfully (e.g. commands that were
aborted, do not get the finished bit set).
Before this commit, there was never a TFES IRQ raised on NCQ error.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-8-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
For NCQ, PxCI is cleared on command queued successfully.
For non-NCQ, PxCI is cleared on command completed successfully.
Successfully means ERR_STAT, BUSY and DRQ are all cleared.
A command that has ERR_STAT set, does not get to clear PxCI.
See AHCI 1.3.1, section 5.3.8, states RegFIS:Entry and RegFIS:ClearCI,
and 5.3.16.5 ERR:FatalTaskfile.
In the case of non-NCQ commands, not clearing PxCI is needed in order
for host software to be able to see which command slot that failed.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-7-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
According to AHCI 1.3.1 definition of PxSACT:
This field is cleared when PxCMD.ST is written from a '1' to a '0' by
software. This field is not cleared by a COMRESET or a software reset.
According to AHCI 1.3.1 definition of PxCI:
This field is also cleared when PxCMD.ST is written from a '1' to a '0'
by software.
Clearing PxCMD.ST is part of the error recovery procedure, see
AHCI 1.3.1, section "6.2 Error Recovery".
If we don't clear PxCI on error recovery, the previous command will
incorrectly still be marked as pending after error recovery.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-6-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
The AHCI spec states that:
For NCQ, PxCI is cleared on command queued successfully.
For non-NCQ, PxCI is cleared on command completed successfully.
(A non-NCQ command that completes with error does not clear PxCI.)
The current QEMU implementation either clears PxCI in check_cmd(),
or in ahci_cmd_done().
check_cmd() will clear PxCI for a command if handle_cmd() returns 0.
handle_cmd() will return -1 if BUSY or DRQ is set.
The QEMU implementation for NCQ commands will currently not set BUSY
or DRQ, so they will always have PxCI cleared by handle_cmd().
ahci_cmd_done() will never even get called for NCQ commands.
Non-NCQ commands are executed by ide_bus_exec_cmd().
Non-NCQ commands in QEMU are implemented either in a sync or in an async
way.
For non-NCQ commands implemented in a sync way, the command handler will
return true, and when ide_bus_exec_cmd() sees that a command handler
returns true, it will call ide_cmd_done() (which will call
ahci_cmd_done()). For a command implemented in a sync way,
ahci_cmd_done() will do nothing (since busy_slot is not set). Instead,
after ide_bus_exec_cmd() has finished, check_cmd() will clear PxCI for
these commands.
For non-NCQ commands implemented in an async way (using either aiocb or
pio_aiocb), the command handler will return false, ide_bus_exec_cmd()
will not call ide_cmd_done(), instead it is expected that the async
callback function will call ide_cmd_done() once the async command is
done. handle_cmd() will set busy_slot, if and only if BUSY or DRQ is
set, and this is checked _after_ ide_bus_exec_cmd() has returned.
handle_cmd() will return -1, so check_cmd() will not clear PxCI.
When the async callback calls ide_cmd_done() (which will call
ahci_cmd_done()), it will see that busy_slot is set, and
ahci_cmd_done() will clear PxCI.
This seems racy, since busy_slot is set _after_ ide_bus_exec_cmd() has
returned. The callback might come before busy_slot gets set. And it is
quite confusing that ahci_cmd_done() will be called for all non-NCQ
commands when the command is done, but will only clear PxCI in certain
cases, even though it will always write a D2H FIS and raise an IRQ.
Even worse, in the case where ahci_cmd_done() does not clear PxCI, it
still raises an IRQ. Host software might thus read an old PxCI value,
since PxCI is cleared (by check_cmd()) after the IRQ has been raised.
Try to simplify this by always setting busy_slot for non-NCQ commands,
such that ahci_cmd_done() will always be responsible for clearing PxCI
for non-NCQ commands.
For NCQ commands, clear PxCI when we receive the D2H FIS, but before
raising the IRQ, see AHCI 1.3.1, section 5.3.8, states RegFIS:Entry and
RegFIS:ClearCI.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-5-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
The way that BUSY + PxCI is cleared for NCQ (FPDMA QUEUED) commands is
described in SATA 3.5a Gold:
11.15 FPDMA QUEUED command protocol
DFPDMAQ2: ClearInterfaceBsy
"Transmit Register Device to Host FIS with the BSY bit cleared to zero
and the DRQ bit cleared to zero and Interrupt bit cleared to zero to
mark interface ready for the next command."
PxCI is currently cleared by handle_cmd(), but we don't write the D2H
FIS to the FIS Receive Area that actually caused PxCI to be cleared.
Similar to how ahci_pio_transfer() calls ahci_write_fis_pio() with an
additional parameter to write a PIO Setup FIS without raising an IRQ,
add a parameter to ahci_write_fis_d2h() so that ahci_write_fis_d2h()
also can write the FIS to the FIS Receive Area without raising an IRQ.
Change process_ncq_command() to call ahci_write_fis_d2h() without
raising an IRQ (similar to ahci_pio_transfer()), such that the FIS
Receive Area is in sync with the PxTFD shadow register.
E.g. Linux reads status and error fields from the FIS Receive Area
directly, so it is wise to keep the FIS Receive Area and the PxTFD
shadow register in sync.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-4-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
Currently, the first time sending an unsupported command
(e.g. READ LOG DMA EXT) will not have ERR_STAT set in the completion.
Sending the unsupported command again, will correctly have ERR_STAT set.
When ide_cmd_permitted() returns false, it calls ide_abort_command().
ide_abort_command() first calls ide_transfer_stop(), which will call
ide_transfer_halt() and ide_cmd_done(), after that ide_abort_command()
sets ERR_STAT in status.
ide_cmd_done() for AHCI will call ahci_write_fis_d2h() which writes the
current status in the FIS, and raises an IRQ. (The status here will not
have ERR_STAT set!).
Thus, we cannot call ide_transfer_stop() before setting ERR_STAT, as
ide_transfer_stop() will result in the FIS being written and an IRQ
being raised.
The reason why it works the second time, is that ERR_STAT will still
be set from the previous command, so when writing the FIS, the
completion will correctly have ERR_STAT set.
Set ERR_STAT before writing the FIS (calling cmd_done), so that we will
raise an error IRQ correctly when receiving an unsupported command.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-3-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
-----BEGIN PGP SIGNATURE-----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=ymmX
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu into staging
aspeed queue:
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmTxsaQACgkQUaNDx8/7
# 7KGXmg//XJNisscl/VWSBaGmH5MbQUAg/QCRalXx1V/lJ8rhE/JqwnWKuoPFd4EN
# iDlh3ufpzxPhHFc9boechuM5ytlrJxpLJoCIJ4sw/4qnO3Dy3Q6BCy1t8Ma62D1u
# oE7cAMHsriJ1uTJNHUTFo72VapTaH2XwFN9lFDuQW45d+WWAXtVJsqvRgFETNmw6
# YYnTTpH2gLTZZFEgOixhWpGLh4Ibc/l8U1VzL0ctQmC11xng0bqk3PAqU9NGzcM5
# MJmEGAxg43CnFu9NJI1nMqC/coi/8PFtrM7HprSwE3H8Jkwncs4ePVT+kZQC+VNQ
# 7EaVkksfEGHlN8XP5+eQDrQ5yT6ve+fbHTLQhwULfeyt0GlQ8h1yewvHCDWo/zw3
# XI1ZyOcNZ2yiaenSUrTPzu0LiqZEJQnzRjPCpgTi1fU08ryEMEaPtr176YDLCguQ
# cpRj4QSZHCrGl/Eo9NlkFP/2rQDKTvCcedKPkYLQtsurSiH/36Oj9YvZycNtZ574
# ortKAtru4YV/rglNX4L8JDhdI+nqvy1liifpJsiS/2KBZDpVFaP8PzGIV40HNy3G
# 8/LVTnaggZaScF3ftHhkg84uQumELS9l2dhsNCL9HqdlrNXLQrVAIR6iuQlpOKBa
# 5S/6h7ZXGOb1qNVQjYp4HCrB7X1KIJYksZ3GdUREf8ot5Ds1FhE=
# =ymmX
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 01 Sep 2023 05:40:52 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu: (26 commits)
hw/sd: Introduce a "sd-card" SPI variant model
hw/sd: Add sd_cmd_SET_BLOCK_COUNT() handler
hw/sd: Add sd_cmd_SEND_TUNING_BLOCK() handler
hw/sd: Add sd_cmd_SEND_RELATIVE_ADDR() handler
hw/sd: Add sd_cmd_ALL_SEND_CID() handler
hw/sd: Add sd_cmd_SEND_OP_CMD() handler
hw/sd: Add sd_cmd_GO_IDLE_STATE() handler
hw/sd: Add sd_cmd_unimplemented() handler
hw/sd: Add sd_cmd_illegal() handler
hw/sd: Introduce sd_cmd_handler type
hw/sd: Move proto_name to SDProto structure
hw/sd: When card is in wrong state, log which spec version is used
hw/sd: When card is in wrong state, log which state it is
hw/sd/sdcard: Return ILLEGAL for CMD19/CMD23 prior SD spec v3.01
aspeed: Get the BlockBackend of FMC0 from the flash device
m25p80: Introduce an helper to retrieve the BlockBackend of a device
aspeed: Create flash devices only when defaults are enabled
hw/ssi: Check for duplicate CS indexes
aspeed/smc: Wire CS lines at reset
hw/ssi: Introduce a ssi_get_cs() helper
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The XIVE interrupt contoller maintains various fields on interrupt
targets in a structure called NVT. Each unit has a NVT cache, backed
by RAM.
When the NVT structure is not local (in RAM) to the chip, the XIVE
interrupt controller forwards the memory operation to the owning chip
using the PC MMIO region configured for this purpose. QEMU does not
need to be so precise since software shouldn't perform any of these
operations. The model implementation is simplified to return the RAM
address of the NVT structure which is then used by pnv_xive_vst_write
or read to perform the operation in RAM.
Remove the last use of pnv_xive_get_remote().
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The notify page of the interrupt controller can either be used to
receive trigger events from the HW controllers (PHB, PSI) or to
reroute interrupts between Interrupt Controllers. In which case, the
VSD table is used to determine the address of the notify page of the
remote IC and the store data is forwarded.
Today, our model grabs the remote VSD (EAS, END, NVT) address using
pnv_xive_get_remote() helper. Be more precise and implement remote END
triggers using a store on the remote IC notify page.
We still have a shortcut in the model for the NVT accesses which we
will address later.
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It will help us model the END triggers on the PowerNV machine, which
can be rerouted to another interrupt controller.
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
to log an error in case of bad configuration of the XIVE tables by the FW.
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It's unnecessary for non-KVM accelerators(TCG, for example),
to call this function, so change the order of kvm_enable() judgment.
The static inline function that returns -1 directly does not work
in TCG's situation.
Signed-off-by: jianchunfu <chunfu.jian@shingroup.cn>
Tested-by: Gautam Menghani <gautam@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
ppce500_reset_device_tree is registered for system reset, but after
c4b075318e this function rerandomizes rng-seed via
qemu_guest_getrandom_nofail. And when loading a snapshot, it tries to read
EVENT_RANDOM that doesn't exist, so we have an error:
qemu-system-ppc: Missing random event in the replay log
To fix this, use qemu_register_reset_nosnapshotload instead of
qemu_register_reset.
Reported-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Fixes: c4b075318e ("hw/ppc: pass random seed to fdt ")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1634
Signed-off-by: Maksim Kostin <maksim.kostin@ispras.ru>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
spapr_machine_reset gets a random number to populate the device-tree
rng seed with. When loading a snapshot for record-replay, the machine
is reset again, and that tries to consume the random event record
again, crashing due to inconsistent record
Fix this by saving the seed to populate the device tree with, and
skipping the rng on snapshot load.
Acked-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the machine is reset to load a new snapshot while being debugged
with replay-record, it is done from another thread, so the CPU does
not run the register setting operations. Set CPU registers directly in
machine reset.
Cc: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Timebase save uses a random number for a legacy vmstate field, which
makes rr snapshot loading unbalanced. The easiest way to deal with this
is just to skip the rng if record-replay is active.
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reading the time more than once to perform an operation always increases
complexity and fragility due to introduced deltas. Simplify the
decrementer write by reading the clock once for the operation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Lower interrupts, delete timers, and set time facility registers
back to initial state on machine reset.
This is not so important for record-replay since timebase and
decrementer are migrated, but it gives a cleaner reset state.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: checkpatch.pl fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When writing a value to the decrementer that raises an exception, the
irq is raised, but the value is not stored so the store doesn't appear
to have changed the register when it is read again.
Always store the write value to the register.
Fixes: e81a982aa5 ("PPC: Clean up DECR implementation")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When storing a large decrementer value with the most significant
implemented bit set, it is to be treated as a negative and sign
extended.
This isn't hit for book3s DEC because of another bug, fixing it
in the next patch exposes this one and can cause additional
problems, so fix this first. It can be hit with HDECR and other
edge triggered types.
Fixes: a8dafa5251 ("target/ppc: Implement large decrementer support for TCG")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: removed extra cpu and pcc variables shadowing local variables ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The decrementer register contains a relative time in timebase units.
When writing to DECR this is converted and stored as an absolute value
in nanosecond units, reading DECR converts back to relative timebase.
The tb<->ns conversion of the relative part can cause rounding such that
a value writen to the decrementer can read back a different, with time
held constant. This is a particular problem for a deterministic icount
and record-replay trace.
Fix this by storing the absolute value in timebase units rather than
nanoseconds. The math before:
store: decr_next = now_ns + decr * ns_per_sec / tb_per_sec
load: decr = (decr_next - now_ns) * tb_per_sec / ns_per_sec
load(store): decr = decr * ns_per_sec / tb_per_sec * tb_per_sec /
ns_per_sec
After:
store: decr_next = now_ns * tb_per_sec / ns_per_sec + decr
load: decr = decr_next - now_ns * tb_per_sec / ns_per_sec
load(store): decr = decr
Fixes: 9fddaa0c0c ("PowerPC merge: real time TB and decrementer - faster and simpler exception handling (Jocelyn Mayer)")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The rule of timers is typically that they should never expire before the
timeout, but some time afterward. Rounding timer intervals up when doing
conversion is the right thing to do.
Under most circumstances it is impossible observe the decrementer
interrupt before the dec register has triggered. However with icount
timing, problems can arise. For example setting DEC to 0 can schedule
the timer for now, causing it to fire before any more instructions
have been executed and DEC is still 0.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These calculations are repeated several times, and they will become
a little more complicated with subsequent changes.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Failing to reset the of_instance_last makes ihandle allocation continue
to increase, which causes record-replay replay fail to match the
recorded trace.
Not resetting claimed_base makes VOF eventually run out of memory after
some resets.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Fixes: fc8c745d50 ("spapr: Implement Open Firmware client interface")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Wire up the H_SET_MODE debug resources to the CIABR and DAWR0 debug
facilities in TCG.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and replace the SDState::spi attribute with a test checking the
SDProto array of commands.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-11-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-10-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-8-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Log illegal commands as GUEST_ERROR.
Note: we are logging back the SDIO commands (CMD5, CMD52-54).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-6-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add 2 command handler arrays in SDProto, for CMD and ACMD.
Have sd_normal_command() / sd_app_command() use these arrays:
if an command handler is registered, call it, otherwise fall
back to current code base.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-5-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Introduce a new structure to hold the bus protocol specific
fields: SDProto. The first field is the protocol name.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-4-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We report the card is in an inconsistent state, but don't precise
in which state it is. Add this information, as it is useful when
debugging problems.
Since we will reuse this code, extract as sd_invalid_state_for_cmd()
helper.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-2-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
CMD19 (SEND_TUNING_BLOCK) and CMD23 (SET_BLOCK_COUNT) were
added in the Physical Layer Simplified Specification v3.01.
When earlier spec version is requested, we should return ILLEGAL.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220509141320.98374-1-philippe.mathieu.daude@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and get rid of an unnecessary drive_get(IF_MTD) call.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It will help in getting rid of some drive_get(IF_MTD) calls by
retrieving the BlockBackend directly from the m25p80 device.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the -nodefaults option is set, flash devices should be created
with :
-blockdev node-name=fmc0,driver=file,filename=./flash.img \
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0 \
To be noted that in this case, the ROM will not be installed and the
initial boot sequence (U-Boot loading) will fetch instructions using
SPI transactions which is significantly slower. That's exactly how HW
operates though.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This to avoid indexes conflicts on the same SSI bus. Adapt machines
using multiple devices on the same bus to avoid breakage.
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, a set of default flash devices is created at machine init
and drives defined on the QEMU command line are associated to the FMC
and SPI controllers in sequence :
-drive file<file>,format=raw,if=mtd
-drive file<file1>,format=raw,if=mtd
The CS lines are wired in the same creation loop. This makes a strong
assumption on the ordering and is not very flexible since only a
limited set of flash devices can be defined : 1 FMC + 1 or 2 SPI,
which is less than what the SoC really supports.
A better alternative would be to define the flash devices on the
command line using a blockdev attached to a CS line of a SSI bus :
-blockdev node-name=fmc0,driver=file,filename=./flash.img
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0
However, user created flash devices are not correctly wired to their
SPI controller and consequently can not be used by the machine. Fix
that and wire the CS lines of all available devices when the SSI bus
is reset.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Simple routine to retrieve a DeviceState object on a SPI bus using its
CS index. It will be useful for the board to wire the CS lines.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Boards will use this new property to identify the device CS line and
wire the SPI controllers accordingly.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Added support for the buffer organization option in pool buffer control
register.when set to 1,The buffer is split into two parts: Lower 16 bytes
for Tx and higher 16 bytes for Rx.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to the ast2600 datasheet and the linux aspeed i2c driver,
the TXBUF transmission start position should be TXBUF[0] instead
of TXBUF[1],so the arg pool_start is useless,and the address is not
included in TXBUF.So even if Tx Count equals zero,there is at least
1 byte data needs to be transmitted,and M_TX_CMD should not be cleared
at this condition.The driver url is:
https://github.com/AspeedTech-BMC/linux/blob/aspeed-master-v5.15/drivers/i2c/busses/i2c-ast2600.c
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 6054fc73e8 ("aspeed/i2c: Add support for pool buffer transfers")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Fixed inconsistency between the regisiter bit field definition header file
and the ast2600 datasheet. The reg name is I2CD1C:Pool Buffer Control
Register in old register mode and I2CC0C: Master/Slave Pool Buffer Control
Register in new register mode. They share bit field
[12:8]:Transmit Data Byte Count and bit field
[29:24]:Actual Received Pool Buffer Size according to the datasheet.
According to the ast2600 datasheet,the actual Tx count is
Transmit Data Byte Count plus 1, and the max Rx size is
Receive Pool Buffer Size plus 1, both in Pool Buffer Control Register.
The version before forgot to plus 1, and mistake Rx count for Rx size.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 3be3d6ccf2 ("aspeed: i2c: Migrate to registerfields API")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On 32-bit hosts, RAM has a 2047 MB limit. Use a macro to define the
default ram size of machines (AST2600 SoC) that can have 2 GB.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
kvmclock_create() is only implemented in hw/i386/kvm/clock.h.
Restrict the "hw/kvm/clock.h" header to i386 by moving it to
hw/i386/.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230620083228.88796-3-philmd@linaro.org>
We shouldn't call kvmclock_create() when KVM is not available
or disabled:
- check for kvm_enabled() before calling it
- assert KVM is enabled once called
Since the call is elided when KVM is not available, we can
remove the stub (it is never compiled).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230620083228.88796-2-philmd@linaro.org>
In xhci_get_port_bandwidth(), we use a variable-length array to
construct the buffer to send back to the guest. Avoid the VLA
by using dma_memory_set() to directly request the memory system
to fill the guest memory with a string of '80's.
The codebase has very few VLAs, and if we can get rid of them all we
can make the compiler error on new additions. This is a defensive
measure against security bugs where an on-stack dynamic allocation
isn't correctly size-checked (e.g. CVE-2021-3527).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230824164818.2652452-1-peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-14-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-18-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230823065335.1919380-7-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230823065335.1919380-15-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-14-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-14-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
QOM object instance should not modify its class state (because
all other objects instanciated from this class get affected).
Instead of modifying the PMBusDeviceClass 'device_num_pages' field
the first time a instance is initialized (in pmbus_pages_alloc),
introduce a new pmbus_pages_num() helper which returns the page
number from the class without modifying the class state.
The code logic become slighly simplified.
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230523064408.57941-4-philmd@linaro.org>
0x400 is Data Register Break Error (DR_BE),
0x10 is Line Control Register Fifo Enabled (LCR_FEN)
and 0x1 is Send Break (LCR_BRK).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230522153144.30610-7-philmd@linaro.org>
PL011_INT_TX duplicates INT_TX, and PL011_INT_RX INT_RX.
Follow other register fields definitions from this file,
keep the shorter form.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230522153144.30610-6-philmd@linaro.org>
To avoid knowing the register addresses by heart,
display their name along in the trace events.
Since the MMIO region is 4K wide (0x1000 bytes),
displaying the address with 3 digits is enough,
so reduce the address format.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230522153144.30610-5-philmd@linaro.org>
The pl011_read() and pl011_write() handlers shift the offset
argument by 2, so are implemented on a 32-bit boundary.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230710175102.32429-2-philmd@linaro.org>
GLib recommend to use G_SOURCE_REMOVE / G_SOURCE_CONTINUE
for GSourceFunc callbacks. Our FEWatchFunc is a GSourceFunc
returning such value. Use such definitions which are
"more memorable" [*].
[*] https://docs.gtk.org/glib/callback.SourceFunc.html#return-value
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230705133139.54419-5-philmd@linaro.org>
Since commit fa92bd4af7 ("target/xtensa: fix access to
the INTERRUPT SR") these files use QEMU atomic API.
Explicit the header inclusion instead of relying on
implicit and indirect inclusion.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-10-philmd@linaro.org>
The 'fs_dma_ctrl' structure has a MemoryRegion 'mmio' field
which is initialized in etraxfs_dmac_init() calling
memory_region_init_io() and memory_region_add_subregion().
These functions are declared in "exec/memory.h", along with
the MemoryRegion structure. Include the missing header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230619074153.44268-3-philmd@linaro.org>
hw/net/i82596.c access the global 'address_space_memory'
calling the ld/st_phys() API. address_space_memory is
declared in "exec/address-spaces.h". Currently this header
is indirectly pulled in via another header. Explicitly include
it to avoid when refactoring unrelated headers:
hw/net/i82596.c:91:23: error: use of undeclared identifier 'address_space_memory'; did you mean 'address_space_destroy'?
return ldub_phys(&address_space_memory, addr);
^~~~~~~~~~~~~~~~~~~~
address_space_destroy
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230619074153.44268-2-philmd@linaro.org>
By default, C function prototypes declared in headers are visible,
so there is no need to declare them as 'extern' functions.
Remove this redundancy in a single bulk commit; do not modify:
- meson.build (used to check function availability at runtime)
- pc-bios/
- libdecnumber/
- tests/
- *.c
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230605175647.88395-5-philmd@linaro.org>
HAX is deprecated since commits 73741fda6c ("MAINTAINERS: Abort
HAXM maintenance") and 90c167a1da ("docs/about/deprecated: Mark
HAXM in QEMU as deprecated"), released in v8.0.0.
Per the latest HAXM release (v7.8 [*]), the latest QEMU supported
is v7.2:
Note: Up to this release, HAXM supports QEMU from 2.9.0 to 7.2.0.
The next commit (https://github.com/intel/haxm/commit/da1b8ec072)
added:
HAXM v7.8.0 is our last release and we will not accept
pull requests or respond to issues after this.
It became very hard to build and test HAXM. Its previous
maintainers made it clear they won't help. It doesn't seem to be
a very good use of QEMU maintainers to spend their time in a dead
project. Save our time by removing this orphan zombie code.
[*] https://github.com/intel/haxm/releases/tag/v7.8.0
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230831082016.60885-1-philmd@linaro.org>
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
-----BEGIN PGP SIGNATURE-----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=MFh3
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmTwbukZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3ihBD/wK8Iz0KpTAwZBDAodnSZrh
# tQnJAvYFp8CxA4O8sZ9IeWsZh90gzsTCZi0NqUTTzvWCJfxkB7qTPdlJT5IzVxou
# oEUk2aogSJhRA3XRJzqArXsPlnZGSYDbtwKx4VtfCvOCCH08Y7nhnFaRj1oFnR4Q
# 0PE/8YtGXTBxLHrO8U3tomg7zElzOUP8ZVZtb30BOyw1jtfSD03IZR8dzpA43u1E
# Hh418WvVekmwFoFNh8yUeHzbyXMZufzvbJPuDGJ8pPWwIpvSG6chOnKF8jZll+Ur
# DqOsDkGlQgcBR2QwYfSPClrEkX8yahJ95PBfM6giG+DQC7OiElqXqTiUGZcpgUVo
# uSUbzS4YPsxCnyVV6SBXV+f/8hdXBxOSHTgl7OAFa8X9OwWwspxHJ/v2o/2ibnUT
# hTTkFp/w1nQwVEN8xf1DOUpm/J2Wr8UeH4f776daSrfKAol2BKbHb8dOgGLQCwqb
# G+iDcE4bkzRqly6f+uVk8xSEZDd9P1NYoxKV+gNlV1dTspdHVpTC+rXMa8dRw5hI
# 4KgaAslj++Xa229xkjORXCJ1cICRIebYg7+SjvTtGBYsFV7plsCcYb/R9yLmhVCf
# fKHKKaYe9sQJ82apOIkTc+nnW8BQQx6XUmU/A//iZ8JGLk6DpJcZ8f1m/2rVZTsl
# 9+lsmpBf4w+uR4o+Womhfw==
# =MFh3
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 31 Aug 2023 06:43:53 EDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm: (24 commits)
hw/arm: Set number of MPU regions correctly for an505, an521, an524
hw/arm/armv7m: Add mpu-ns-regions and mpu-s-regions properties
target/arm: Do all "ARM_FEATURE_X implies Y" checks in post_init
rtc: Use time_t for passing and returning time offsets
hw/rtc/aspeed_rtc: Use 64-bit offset for holding time_t difference
hw/rtc/twl92230: Use int64_t for sec_offset and alm_sec
hw/rtc/m48t59: Use 64-bit arithmetic in set_alarm()
target/arm: Catch illegal-exception-return from EL3 with bad NSE/NS
Add i.MX7 SRC device implementation
Add i.MX7 missing TZ devices and memory regions
Refactor i.MX7 processor code
Add i.MX6UL missing devices.
Refactor i.MX6UL processor code
Remove i.MX7 IOMUX GPR device from i.MX6UL
target/arm: properly document FEAT_CRC32
target/arm: Implement FEAT_HPDS2 as a no-op
target/arm: Suppress FEAT_TRBE (Trace Buffer Extension)
target/arm: Apply access checks to neoverse-v1 special registers
target/arm: Apply access checks to neoverse-n1 special registers
target/arm: Introduce make_ccsidr64
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The IoTKit, SSE200 and SSE300 all default to 8 MPU regions. The
MPS2/MPS3 FPGA images don't override these except in the case of
AN547, which uses 16 MPU regions.
Define properties on the ARMSSE object for the MPU regions (using the
same names as the documented RTL configuration settings, and
following the pattern we already have for this device of using
all-caps names as the RTL does), and set them in the board code.
We don't actually need to override the default except on AN547,
but it's simpler code to have the board code set them always
rather than tracking which board subtypes want to set them to
a non-default value separately from what that value is.
Tho overall effect is that for mps2-an505, mps2-an521 and mps3-an524
we now correctly use 8 MPU regions, while mps3-an547 stays at its
current 16 regions.
It's possible some guest code wrongly depended on the previous
incorrectly modeled number of memory regions. (Such guest code
should ideally check the number of regions via the MPU_TYPE
register.) The old behaviour can be obtained with additional
-global arguments to QEMU:
For mps2-an521 and mps2-an524:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16 -global sse-200.CPU1_MPU_NS=16 -global sse-200.CPU1_MPU_S=16
For mps2-an505:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16
NB that the way the implementation allows this use of -global
is slightly fragile: if the board code explicitly sets the
properties on the sse-200 object, this overrides the -global
command line option. So we rely on:
- the boards that need fixing all happen to use the SSE defaults
- we can write the board code to only set the property if it
is different from the default, rather than having all boards
explicitly set the property
- the board that does need to use a non-default value happens
to need to set it to the same value (16) we previously used
This works, but there are some kinds of refactoring of the
mps2-tz.c code that would break the support for -global here.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1772
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-4-peter.maydell@linaro.org
M-profile CPUs generally allow configuration of the number of MPU
regions that they have. We don't currently model this, so our
implementations of some of the board models provide CPUs with the
wrong number of regions. RTOSes like Zephyr that hardcode the
expected number of regions may therefore not run on the model if they
are set up to run on real hardware.
Add properties mpu-ns-regions and mpu-s-regions to the ARMV7M object,
matching the ability of hardware to configure the number of Secure
and NonSecure regions separately. Our actual CPU implementation
doesn't currently support that, and it happens that none of the MPS
boards we model set the number of regions differently for Secure vs
NonSecure, so we provide an interface to the boards and SoCs that
won't need to change if we ever do add that functionality in future,
but make it an error to configure the two properties to different
values.
(The property name on the CPU is the somewhat misnamed-for-M-profile
"pmsav7-dregion", so we don't follow that naming convention for
the properties here. The TRM doesn't say what the CPU configuration
variable names are, so we pick something, and follow the lowercase
convention we already have for properties here.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-3-peter.maydell@linaro.org
In the aspeed_rtc device we store a difference between two time_t
values in an 'int'. This is not really correct when time_t could
be 64 bits. Enlarge the field to 'int64_t'.
This is a migration compatibility break for the aspeed boards.
While we are changing the vmstate, remove the accidental
duplicate of the offset field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
In the twl92230 device, use int64_t for the two state fields
sec_offset and alm_sec, because we set these to values that
are either time_t or differences between two time_t values.
These fields aren't saved in vmstate anywhere, so we can
safely widen them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In the m48t59 device we almost always use 64-bit arithmetic when
dealing with time_t deltas. The one exception is in set_alarm(),
which currently uses a plain 'int' to hold the difference between two
time_t values. Switch to int64_t instead to avoid any possible
overflow issues.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The SRC device is normally used to start the secondary CPU.
When running Linux directly, QEMU is emulating a PSCI interface that UBOOT
is installing at boot time and therefore the fact that the SRC device is
unimplemented is hidden as Qemu respond directly to PSCI requets without
using the SRC device.
But if you try to run a more bare metal application (maybe uboot itself),
then it is not possible to start the secondary CPU as the SRC is an
unimplemented device.
This patch adds the ability to start the secondary CPU through the SRC
device so that you can use this feature in bare metal applications.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ce9a0162defd2acee5dc7f8a674743de0cded569.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add various memory segments
- OCRAM
- OCRAM EPDC
- OCRAM PXP
- OCRAM S
- ROM
- CAAM
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: f887a3483996ba06d40bd62ffdfb0ecf68621987.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for all i.MX7 devices in i.MX7 header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 59e195d33e4d486a8d131392acd46633c8c10ed7.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add 4 missing PWM devices
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 59e4dc56e14eccfefd379275ec19048dff9c10b3.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for most i.MX6UL devices in i.MX6UL header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: d579043fbd4e4b490370783fda43fc02c8e9be75.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
i.MX7 IOMUX GPR device is not equivalent to i.MX6UL IOMUXC GPR device.
In particular, register 22 is not present on i.MX6UL and this is actualy
The only register that is really emulated in the i.MX7 IOMUX GPR device.
Note: The i.MX6UL code is actually also implementing the IOMUX GPR device
as an unimplemented device at the same bus adress and the 2 instantiations
were actualy colliding. So we go back to the unimplemented device for now.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 48681bf51ee97646479bb261bee19abebbc8074e.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to use virtio backends we need to initialize RAM for the
xen-mapcache (which is responsible for mapping guest memory using foreign
mapping) to work. Calculate and add hi/low memory regions based on
machine->ram_size.
Use the constants defined in public header arch-arm.h to be aligned with the xen
toolstack.
While using this machine, the toolstack should then pass real ram_size using
"-m" arg. If "-m" is not given, create a QEMU machine without IOREQ and other
emulated devices like TPM and VIRTIO. This is done to keep this QEMU machine
usable for /etc/init.d/xencommons.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
In order to use virtio backends we need to allocate virtio-mmio
parameters (irq and base) and register corresponding buses.
Use the constants defined in public header arch-arm.h to be
aligned with the toolstack. So the number of current supported
virtio-mmio devices is 10.
For the interrupts triggering use already existing on Arm
device-model hypercall.
The toolstack should then insert the same amount of device nodes
into guest device-tree.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
'bool is_write' style is obsolete from throttle framework, adapt
fsdev to the new style.
Cc: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20230728022006.1098509-9-pizhenwei@bytedance.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
In hw/acpi/aml-build.c:build_pptt() function, the code assumes that the
ACPI processor id equals to the cpu index, for example if we have 8
cpus, then the ACPI processor id should be in range 0-7.
However, in hw/loongarch/acpi-build.c:build_madt() function we broke the
assumption. If we have 8 cpus again, the ACPI processor id in MADT table
would be in range 1-8. It violates the following description taken from
ACPI spec 6.4 table 5.138:
If the processor structure represents an actual processor, this field
must match the value of ACPI processor ID field in the processor’s entry
in the MADT.
It will break the latest Linux 6.5-rc6 with the
following error message:
ACPI PPTT: PPTT table found, but unable to locate core 7 (8)
Invalid BIOS PPTT
Here 7 is the last cpu index, 8 is the ACPI processor id learned from
MADT.
With this patch, Linux can properly detect SMT threads when "-smp
8,sockets=1,cores=4,threads=2" is passed:
Thread(s) per core: 2
Core(s) per socket: 2
Socket(s): 2
The detection of number of sockets is still wrong, but that is out of
scope of the commit.
Signed-off-by: Jiajie Chen <c@jia.je>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20230820105658.99123-2-c@jia.je>
Signed-off-by: Song Gao <gaosong@loongson.cn>
For edge triggered irq, qemu_irq_pulse is used to inject irq. It will
set irq with high level and low level soon to simluate pulse irq.
For edge triggered irq, irq is injected and set as pending at rising
level, do not clear irq at lowering level. LoongArch pch interrupt will
clear irq for lowering level irq, there will be problem. ACPI ged deivce
is edge-triggered irq, it is used for cpu/memory hotplug.
This patch fixes memory hotplug issue on LoongArch virt machine.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230707091557.1474790-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement the callback for getting the architecture-dependent CPU
ID, the cpu ID is physical id described in ACPI MADT table, this
will be used for cpu hotplug.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230824005007.2000525-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Allow virt machine to be used with la132 instead of la464.
Co-authored-by: Jiajie Chen <c@jia.je>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230822032724.1353391-11-gaosong@loongson.cn>
Message-Id: <20230822071959.35620-5-philmd@linaro.org>
The check for nd->model being NULL was originally required, but in
commit e11f463295 ("s390x/virtio: use qemu_check_nic_model()")
the corresponding code had been replaced by a call to the function
qemu_check_nic_model() - and this in turn calls qemu_find_nic_model()
which contains the same check for nd->model being NULL again. So we
can remove this from the calling site now.
Message-Id: <20230804073525.11857-1-thuth@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Output message are slightly modified to ease selection with wildcards
and to report extra parameters.
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20230804080415.56852-1-clg@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
On MIPS, kvm_arch_get_default_type() returns a negative value when an
error occurred so handle the case. Also, let other machines return
negative values when errors occur and declare returning a negative
value as the correct way to propagate an error that happened when
determining KVM type.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-5-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
kvm_arch_get_default_type() returns the default KVM type. This hook is
particularly useful to derive a KVM type that is valid for "none"
machine model, which is used by libvirt to probe the availability of
KVM.
For MIPS, the existing mips_kvm_type() is reused. This function ensures
the availability of VZ which is mandatory to use KVM on the current
QEMU.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-2-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added doc comment for new function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Implement nRF51 DETECT signal in the GPIO peripheral.
The reference manual makes mention of a per-pin DETECT signal, but these
are not exposed to the user. See https://devzone.nordicsemi.com/f/nordic-q-a/39858/gpio-per-pin-detect-signal-available
for more information. Currently, I don't see a reason to model these.
Signed-off-by: Chris Laplante <chris@laplante.io>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230728160324.1159090-2-chris@laplante.io
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a last minute PR for RISC-V.
The main goal is to fix
https://gitlab.com/qemu-project/qemu/-/issues/1823
which is a regression that means the aclint option
cannot be enabled.
While we are here we also fixup KVM issue.
* KVM: fix mvendorid size
* Fixup aclint check
-----BEGIN PGP SIGNATURE-----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=x8Fl
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230811-3' of https://github.com/alistair23/qemu into staging
Sixth RISC-V PR for 8.1
This is a last minute PR for RISC-V.
The main goal is to fix
https://gitlab.com/qemu-project/qemu/-/issues/1823
which is a regression that means the aclint option
cannot be enabled.
While we are here we also fixup KVM issue.
* KVM: fix mvendorid size
* Fixup aclint check
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmTWfK0ACgkQr3yVEwxT
# gBNDTw/9EnIjXKBCwSejcL3xYpwTDbUbwou3dkkSjnEkhmxvPPM3H0pWet+xYlPg
# Lgt9b9clHZAjqGoHFxEdU8fS0MY4Jq5jDAinsS2TK6czLPBe5EEhyVjoDH5iRhTX
# AymK1XgwQ2kAuw2lhcb74GDboajkC7hNhr2Km1hLtpYV7bCW/efAUSO7adG4KBlB
# SCu06s9VdFtINW0mVN249JvRVQ1408HCQ5gwA0lLVdXhfHluVidwOjc//ELtdnQn
# SeHdX1V+e+3fiYuqmr2UHaJXp9s0ZInOyLIDBPA97SOUdaO/oy+siZYRk25yV99h
# Ec7tpNnYJjzppmc++GlzTNpUWVEBM6j+QyD7ioEj4yAGkMEjUlgLcImyGng1TT4i
# uvABg91uzJyBoUga3GhZYt/sPW00Jft4VYH3QvGOOwjarIor8K0J7sox8eIOfEs4
# JqCIYX4kas+DwK4+i8WyjMeuihWFJ5ipKR7Gwhbe5uQ5szTXFYIT4TZH/78BWozI
# dMu5HOyu5+l9yCy39NP7FjNJ6VQKBYGvlkUr5rLRS0yQWGThaK8wIBMXcuZCW96p
# hSy/pratHQYaIRr0ZiqRcNyFNsTMua/C2DMPcjQR1ci8xdj010DoriyS0Vsh88xq
# pVgC6gYn59gDUdBx0gB/ZSMu4O+F/+Z5htnucoTxvwpKxUU48Lg=
# =x8Fl
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 11 Aug 2023 11:23:41 AM PDT
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20230811-3' of https://github.com/alistair23/qemu:
hw/riscv/virt.c: change 'aclint' TCG check
target/riscv/kvm.c: fix mvendorid size in vcpu_set_machine_ids()
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The 'aclint' property is being conditioned with tcg acceleration in
virt_machine_class_init(). But acceleration code starts later than the
class init of the board, meaning that tcg_enabled() will be always be
false during class_init(), and the option is never being declared even
when declaring TCG accel:
$ ./build/qemu-system-riscv64 -M virt,accel=tcg,aclint=on
qemu-system-riscv64: Property 'virt-machine.aclint' not found
Fix it by moving the check from class_init() to machine_init(). Tune the
description to mention that the option is TCG only.
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Fixes: c0716c81b ("hw/riscv/virt: Restrict ACLINT to TCG")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1823
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230811160224.440697-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
two fixes that seem very safe and important enough to sneak
in before the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmTWXvIPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpe7sH/0KteOBt324LUYZ+4NR6EQE5KDsCANGiySBK
r0B6lhcFHvNd2ej0g2hW7lL6nVVCQBkJLLzfNIR/aHkeCmOttfbhv4eF4S6Ho27d
DpkXCPZRT6F11gY7G1swFapNS/f0P7F5LGRjq4sbuw3FpyHBz0DqCQ0GOab2Qorq
VfuOfA01nYGNzHOKrEL7k9Io55oqPVcAe+5TaipNCQ4nW82i32ItTyFjQFdLIAay
qY4HEwP9vPuVwWNdQjXJNfirLMO5GQfEbyKDAjap2sL25zAV2w+mgn7xg/xkTfM6
iMX2m14lKRMy2hr8dEVh/XdLf7loAN1jSE8/Wdt+PEaexolqxCM=
=1GLE
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
pci: last minute bugfixes
two fixes that seem very safe and important enough to sneak
in before the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmTWXvIPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpe7sH/0KteOBt324LUYZ+4NR6EQE5KDsCANGiySBK
# r0B6lhcFHvNd2ej0g2hW7lL6nVVCQBkJLLzfNIR/aHkeCmOttfbhv4eF4S6Ho27d
# DpkXCPZRT6F11gY7G1swFapNS/f0P7F5LGRjq4sbuw3FpyHBz0DqCQ0GOab2Qorq
# VfuOfA01nYGNzHOKrEL7k9Io55oqPVcAe+5TaipNCQ4nW82i32ItTyFjQFdLIAay
# qY4HEwP9vPuVwWNdQjXJNfirLMO5GQfEbyKDAjap2sL25zAV2w+mgn7xg/xkTfM6
# iMX2m14lKRMy2hr8dEVh/XdLf7loAN1jSE8/Wdt+PEaexolqxCM=
# =1GLE
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 11 Aug 2023 09:16:50 AM PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu:
pci: Fix the update of interrupt disable bit in PCI_COMMAND register
hw/pci-host: Allow extended config space access for Designware PCIe host
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The PCI_COMMAND register is located at offset 4 within
the PCI configuration space and occupies 2 bytes. The
interrupt disable bit is at the 10th bit, which corresponds
to the byte at offset 5 in the PCI configuration space.
In our testing environment, the guest driver may directly
updates the byte at offset 5 in the PCI configuration space.
The backtrace looks like as following:
at hw/pci/pci.c:1442
at hw/virtio/virtio-pci.c:605
val=5, len=1) at hw/pci/pci_host.c:81
In this situation, the range_covers_byte function called
by the pci_default_write_config function will return false,
resulting in the inability to handle the interrupt disable
update event.
To fix this issue, we can use the ranges_overlap function
instead of range_covers_byte to determine whether the interrupt
bit has been updated.
Signed-off-by: Guoyi Tu <tugy@chinatelecom.cn>
Signed-off-by: yuanminghao <yuanmh12@chinatelecom.cn>
Message-Id: <ce2d0437-8faa-4d61-b536-4668f645a959@chinatelecom.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: b6981cb57b ("pci: interrupt disable bit support")
In pcie_bus_realize(), a root bus is realized as a PCIe bus and a non-root
bus is realized as a PCIe bus if its parent bus is a PCIe bus. However,
the child bus "dw-pcie" is realized before the parent bus "pcie" which is
the root PCIe bus. Thus, the extended configuration space is not accessible
on "dw-pcie". The issue can be resolved by adding the
PCI_BUS_EXTENDED_CONFIG_SPACE flag to "pcie" before "dw-pcie" is realized.
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Message-Id: <20230809102257.25121-1-jason.chien@sifive.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Signed-off-by: Jason Chien <<a href="mailto:jason.chien@sifive.com" target="_blank">jason.chien@sifive.com</a>><br>
The Reclaim Unit Update operation in I/O Management Receive does not
verify the presence of a configured endurance group prior to accessing
it.
Fix this.
Cc: qemu-stable@nongnu.org
Fixes: 73064edfb8 ("hw/nvme: flexible data placement emulation")
Reviewed-by: Jesper Wendel Devantier <j.devantier@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_directive_receive() does not check if an endurance group has been
configured (set) prior to testing if flexible data placement is enabled
or not.
Fix this.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1815
Fixes: 73064edfb8 ("hw/nvme: flexible data placement emulation")
Reviewed-by: Jesper Wendel Devantier <j.devantier@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The nvme CRC64 generator expects the caller to pass inverted seed value.
Pass inverted crc value for metadata buffer.
Cc: qemu-stable@nongnu.org
Fixes: 44219b6029 ("hw/nvme: 64-bit pi support")
Signed-off-by: Ankit Kumar <ankit.kumar@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Hi,
Here is a collection of ui, dump and chardev fixes that are worth for 8.1.
thanks
-----BEGIN PGP SIGNATURE-----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=ANQg
-----END PGP SIGNATURE-----
Merge tag 'fixes-pull-request' of https://gitlab.com/marcandre.lureau/qemu into staging
Fixes for 8.1
Hi,
Here is a collection of ui, dump and chardev fixes that are worth for 8.1.
thanks
# -----BEGIN PGP SIGNATURE-----
#
# iQJQBAABCAA6FiEEh6m9kz+HxgbSdvYt2ujhCXWWnOUFAmTRWDscHG1hcmNhbmRy
# ZS5sdXJlYXVAcmVkaGF0LmNvbQAKCRDa6OEJdZac5eUrD/9BvqJ87XSKchV01jji
# PmA+yFyI0JSG68oYbNPYJXxkLWdRCKp6GGcT8h1yiVtGH/SVey9spxDqbV+sK0uW
# FmqIcmSBbjI4A6+Mne07Iyd0QtgL9H6YNenRXDFLIXLh84HP47Dg9vfgx4AsRY7O
# efcCdi43/PoJOelVfn9wIkP/8DU4pZV6IsdtdUxZ3rtu/zwjW61rLzuxtLcAoCIE
# rAYiTp699NH5fKBbMzm3puK4hpaPLj4GuGPrSaWVSCcgARqi7LWpgZC5i+a6FUfS
# eWzK8WkdvHIPaUPRNl70LTWPKVxJ4PdSxFlIKgiH0bnpXHBvJnO2y1v4jaiGI0y2
# WSHKJWY513zTF4B+pMdQLjNiLotkiqtAXHw5rrjPTuVHxi1N5w6Z/BvWOSAvs8V6
# ijYmjksNoqwfpbPRTyu8psLcmj3fo2UIjQ739PgLN2lfC8d+nzdx4PIIq/ybQdZZ
# 7QBJGhxP33Ou8c3ok43Jz3go6w0WOKM0ucG1K1iTVxQ27leMKTO5Zsm2TShG2pMG
# CY6d/dumID8+G7sho8TmtTDjC5ZBkY5e27etkS+P4p+Buc60lqDrL+u6UadxWNZ1
# 3ifsQ1PhVTRuhZUJNMcX1Qo3PuEfAOH1ZuCbvXpubHwcUr4o/ZqlVrMaJtYB3ueo
# 7SX8YistmktaEeN+Y50qoiEVgg==
# =ANQg
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 07 Aug 2023 01:46:51 PM PDT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
* tag 'fixes-pull-request' of https://gitlab.com/marcandre.lureau/qemu:
ui/gtk: set scanout mode in gd_egl/gd_gl_area_scanout_texture
hw/i386/vmmouse:add relative packet flag for button status
dump: kdump-zlib data pages not dumped with pvtime/aarch64
virtio-gpu: reset gfx resources in main thread
virtio-gpu: free BHs, by implementing unrealize
chardev: report the handshake error
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The buttons value use macros instead of direct numbers.
If request relative mode, have to add this for
guest vmmouse driver to judge this is a relative packet.
otherwise,vmmouse driver will not match
the condition 'status & VMMOUSE_RELATIVE_PACKET',
and can't report events on the correct(relative) input device,
result to relative mode unuseful.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Message-ID: <20230413081526.2229916-1-zhouzongmin@kylinos.cn>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Calling OpenGL from different threads can have bad consequences if not
carefully reviewed. It's not generally supported. In my case, I was
debugging a crash in glDeleteTextures from OPENGL32.DLL, where I asked
qemu for gl=es, and thus ANGLE implementation was expected. libepoxy did
resolution of the global pointer for glGenTexture to the GLES version
from the main thread. But it resolved glDeleteTextures to the GL
version, because it was done from a different thread without correct
context. Oops.
Let's stick to the main thread for GL calls by using a BH.
Note: I didn't use atomics for reset_finished check, assuming the BQL
will provide enough of sync, but I might be wrong.
Acked-by: Dongwon Kim <dongwon.kim@intel.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230726173929.690601-3-marcandre.lureau@redhat.com>
The clock and data values were logged swapped. Correct the trace event
text to match what is logged. Also fix a typo in a comment nearby.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
As of prior to this patch, the controller checks the value of CC.IOCQES
and CC.IOSQES prior to enabling the controller. As reported by Ben in
GitLab issue #1691, this is not spec compliant. The controller should
only check these values when queues are created.
This patch moves these checks to nvme_create_cq(). We do not need to
check it in nvme_create_sq() since that will error out if the completion
queue is not already created.
Also, since the controller exclusively supports SQEs of size 64 bytes
and CQEs of size 16 bytes, hard code that.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1691
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
As reported by Trend Micro's Zero Day Initiative, an oob memory read
vulnerability exists in nvme_fdp_events(). The host-provided offset is
not verified.
Fix this.
This is only exploitable when Flexible Data Placement mode (fdp=on) is
enabled.
Fixes: CVE-2023-4135
Fixes: 73064edfb8 ("hw/nvme: flexible data placement emulation")
Reported-by: Trend Micro's Zero Day Initiative
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The board firmware handles this correctly following the Open Firmware
standard which we missed. This fixes 64 bit BARs when using VOF.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <20230721221320.1311E7456AB@zero.eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The board firmware names devices by their class so match that for
common devices. Also make sure the /rtas node has a name. This is
needed because VOF otherwise does not include it in results got by
nextprop which is how AmigaOS queries it and fails if no name property
is found.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <808ade37aa141563d1ee349254151672bf7a5d59.1689725688.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The register offset of the ROM BAR is 0x30 not 0x28. This fixes the
reg property entry of the ROM region in the device tree.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <6abd73b1211f9d0776dfa5d71d6294f17eecb426.1689725688.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The original non-free board firmware sets the command register of the
USB functions to 7 and some guests rely on this for working USB. Match
what the board firmware does when using VOF instead.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <06a2b864431425f23d1f2b5abf0c027819ac11c6.1689725688.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
For symmetric algorithms, the length of ciphertext must be as same
as the plaintext.
The missing verification of the src_len and the dst_len in
virtio_crypto_sym_op_helper() may lead buffer overflow/divulged.
This patch is originally written by Yiming Tao for QEMU-SECURITY,
resend it(a few changes of error message) in qemu-devel.
Fixes: CVE-2023-3180
Fixes: 04b9b37edda("virtio-crypto: add data queue processing handler")
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: Mauro Matteo Cascella <mcascell@redhat.com>
Cc: Yiming Tao <taoym@zju.edu.cn>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20230803024314.29962-2-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The values in "msg" are assembled in host endian byte order (the other
field are also not swapped), so we must not swap the __addr_head here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-6-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
The values in "addr" are populated locally in this function in host
endian byte order, so we must not swap the index_l field here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-5-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
On big endian hosts, we need to reverse the bitfield order in the
struct VTDInvDescIEC, just like it is already done for the other
bitfields in the various structs of the intel-iommu device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-4-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The code already tries to do some endianness handling here, but
currently fails badly:
- While it already swaps the data when logging errors / tracing, it fails
to byteswap the value before e.g. accessing entry->irte.present
- entry->irte.source_id is swapped with le32_to_cpu(), though this is
a 16-bit value
- The whole union is apparently supposed to be swapped via the 64-bit
data[2] array, but the struct is a mixture between 32 bit values
(the first 8 bytes) and 64 bit values (the second 8 bytes), so this
cannot work as expected.
Fix it by converting the struct to two proper 64-bit bitfields, and
by swapping the values only once for everybody right after reading
the data from memory.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-3-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
After reading the guest memory with dma_memory_read(), we have
to make sure that we byteswap the little endian data to the host's
byte order.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-2-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
When the vhost-user reconnect to the backend, the notifer should be
cleanup. Otherwise, the fd resource will be exhausted.
Fixes: f9a09ca3ea ("vhost: add support for configure interrupt")
Signed-off-by: Li Feng <fengli@smartx.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20230731121018.2856310-2-fengli@smartx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=2224964
In migration with VF failover, Windows guest and ACPI hot
unplug we do not need to satisfy config requests, otherwise
the guest immediately detects the device and brings up its
driver. Many network VF's are stuck on the guest PCI bus after
the migration.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-Id: <20230728084049.191454-1-yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio_queue_packed_set_last_avail_idx() is used by vhost devices to set
the internal queue indices to what has been reported by the vhost
back-end through GET_VRING_BASE. For packed virtqueues, this
32-bit value is expected to contain both the device's internal avail and
used indices, as well as their respective wrap counters.
To get the used index, we shift the 32-bit value right by 16, and then
apply a mask of 0x7ffff. That seems to be a typo, because it should be
0x7fff; first of all, the virtio specification says that the maximum
queue size for packed virt queues is 2^15, so the indices cannot exceed
2^15 - 1 anyway, making 0x7fff the correct mask. Second, the mask
clearly is wrong from context, too, given that (A) `idx & 0x70000` must
be 0 at this point (`idx` is 32 bit and was shifted to the right by 16
already), (B) `idx & 0x8000` is the used_wrap_counter, so should not be
part of the used index, and (C) `vq->used_idx` is a `uint16_t`, so
cannot fit the 0x70000 part of the mask anyway.
This most likely never produced any guest-visible bugs, though, because
for a vhost device, qemu will probably not evaluate the used index
outside of virtio_queue_packed_get_last_avail_idx(), where we
reconstruct the 32-bit value from avail and used indices and their wrap
counters again. There, it does not matter whether the highest bit of
the used_idx is the used index wrap counter, because we put the wrap
counter exactly in that position anyway.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-Id: <20230721134945.26967-1-hreitz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: German Maglione <gmaglione@redhat.com>
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20230721072820.75797-1-david.edmondson@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
ACPI spec (since 2.0a) says
"
A device object must contain either an _HID object or
an _ADR object, but can contain both.
"
_ADR is used when device is attached to an ennumerable bus,
however hostbridge is not and uses dedicated _HID for
discovery, drop _ADR field.
It doesn't seem that having _ADR has a negative effects
OSes manage to tolerate that, but there is no point of
having it there. (only pc/q35 has it hostbridge description,
while others (microvm/arm) don't)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230720133858.1974024-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it seems that Windows is unable to handle variable references
making it choke up when accessing ASUN during _DSM call
when device is hotplugged (it lists package elements as DataAlias
but despite that later on it misbehaves) with following error
shown up in AMLI debugger (WS2012r2):
Store(ShiftLeft(One,Arg1="ASUN",) AMLI_ERROR(c0140008): Unexpected argument type
ValidateArgTypes: expected Arg1 to be type Integer (Type=String)
Similar outcome with WS2022.
Issue is not fatal but as result acpi-index/"PCI Label ID" property
is either not shown in device details page or shows incorrect value.
Fix it by doing assignment of BSEL/ASUN values to package
elements manually after package declaration.
Fix was tested with: WS2012r2, WS2022, RHEL9
Fixes: 467d099a29 (x86: acpi: _DSM: use Package to pass parameters)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230720133858.1974024-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The QEMU CI fails in virtio-scmi test occasionally. As reported by
Thomas Huth, this happens most likely when the system is loaded and it
fails with the following error:
qemu-system-aarch64: ../../devel/qemu/hw/pci/msix.c:659:
msix_unset_vector_notifiers: Assertion `dev->msix_vector_use_notifier && dev->msix_vector_release_notifier' failed.
../../devel/qemu/tests/qtest/libqtest.c:200: kill_qemu() detected QEMU death from signal 6 (Aborted) (core dumped)
As discovered by Fabiano Rosas, the cause is a duplicate invocation of
msix_unset_vector_notifiers via duplicate vu_scmi_stop calls:
msix_unset_vector_notifiers
virtio_pci_set_guest_notifiers
vu_scmi_stop
vu_scmi_disconnect
...
qemu_chr_write_buffer
msix_unset_vector_notifiers
virtio_pci_set_guest_notifiers
vu_scmi_stop
vu_scmi_set_status
...
qemu_cleanup
While vu_scmi_stop calls are protected by vhost_dev_is_started()
check, it's apparently not enough. vhost-user-blk and vhost-user-gpio
use an extra protection, see f5b22d06fb (vhost: recheck dev state in
the vhost_migration_log routine) for the motivation. Let's use the
same in vhost-user-scmi, which fixes the failure above.
Fixes: a5dab090e1 ("hw/virtio: Add boilerplate for vhost-user-scmi device")
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Message-Id: <20230720101037.2161450-1-mzamazal@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
At several locations we compute the granule from the config
page_size_mask using ctz() and then format it in traces using
BIT(). As the page_size_mask is 64b we should use ctz64 and
BIT_ULL() for formatting. We failed to be consistent.
Note the page_size_mask is garanteed to be non null. The spec
mandates the device to set at least one bit, so ctz64 cannot
return 64. This is garanteed by the fact the device
initializes the page_size_mask to qemu_target_page_mask()
and then the page_size_mask is further constrained by
virtio_iommu_set_page_size_mask() callback which can't
result in a new mask being null. So if Coverity complains
round those ctz64/BIT_ULL with CID 1517772 this is a false
positive
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Fixes: 94df5b2180 ("virtio-iommu: Fix 64kB host page size VFIO device assignment")
Message-Id: <20230718182136.40096-1-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
In build_cdat_table() we do:
*cdat_table = g_malloc0(sizeof(*cdat_table) * CXL_USP_CDAT_NUM_ENTRIES);
This is wrong because:
- cdat_table has type CDATSubHeader ***
- so *cdat_table has type CDATSubHeader **
- so the array we're allocating here should be items of type CDATSubHeader *
- but we pass sizeof(*cdat_table), which is sizeof(CDATSubHeader **),
implying that we're allocating an array of CDATSubHeader **
It happens that sizeof(CDATSubHeader **) == sizeof(CDATSubHeader *)
so nothing blows up, but this should be sizeof(**cdat_table).
Avoid this excessively hard-to-understand code by using
g_new0() instead, which will do the type checking for us.
While we're here, we can drop the useless check against failure,
as g_malloc0() and g_new0() never fail.
This fixes Coverity issue CID 1508120.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230718101327.1111374-1-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the virtio_iommu_handle_command() when a PROBE request is handled,
output_size takes a value greater than the tail size and on a subsequent
iteration we can get a stack out-of-band access. Initialize the
output_size on each iteration.
The issue was found with ASAN. Credits to:
Yiming Tao(Zhejiang University)
Gaoning Pan(Zhejiang University)
Fixes: 1733eebb9e ("virtio-iommu: Implement RESV_MEM probe request")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Mauro Matteo Cascella <mcascell@redhat.com>
Cc: qemu-stable@nongnu.org
Message-Id: <20230717162126.11693-1-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230730180329.851576-1-sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Fuzzing showed that a guest could bind an interdomain port to itself, by
guessing the next port to be allocated and putting that as the 'remote'
port number. By chance, that works because the newly-allocated port has
type EVTCHNSTAT_unbound. It shouldn't.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230801175747.145906-4-dwmw2@infradead.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Coverity points out (CID 1508128) a bounds checking error. We need to check
for gsi >= IOAPIC_NUM_PINS, not just greater-than.
Also fix up an assert() that has the same problem, that Coverity didn't see.
Fixes: 4f81baa33e ("hw/xen: Support GSI mapping to PIRQ")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230801175747.145906-2-dwmw2@infradead.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The IDE unplug function needs to reset the entire PCI device, to make
sure all state is initialized to defaults. This is done by calling
pci_device_reset, which resets not only the chip specific registers, but
also all PCI state. This fixes "unplug" in a Xen HVM domU with the
modular legacy xenlinux PV drivers.
Commit ee358e919e ("hw/ide/piix: Convert reset handler to
DeviceReset") changed the way how the the disks are unplugged. Prior
this commit the PCI device remained unchanged. After this change,
piix_ide_reset is exercised after the "unplug" command, which was not
the case prior that commit. This function resets the command register.
As a result the ata_piix driver inside the domU will see a disabled PCI
device. The generic PCI code will reenable the PCI device. On the qemu
side, this runs pci_default_write_config/pci_update_mappings. Here a
changed address is returned by pci_bar_address, this is the address
which was truncated in piix_ide_reset. In case of a Xen HVM domU, the
address changes from 0xc120 to 0xc100. This truncation was a bug in
piix_ide_reset, which was fixed in commit 230dfd9257 ("hw/ide/piix:
properly initialize the BMIBA register"). If pci_xen_ide_unplug had used
pci_device_reset, the PCI registers would have been properly reset, and
commit ee358e919e would have not introduced a regression for this
specific domU environment.
While the unplug is supposed to hide the IDE disks, the changed BMIBA
address broke the UHCI device. In case the domU has an USB tablet
configured, to recive absolute pointer coordinates for the GUI, it will
cause a hang during device discovery of the partly discovered USB hid
device. Reading the USBSTS word size register will fail. The access ends
up in the QEMU piix-bmdma device, instead of the expected uhci device.
Here a byte size request is expected, and a value of ~0 is returned. As
a result the UCHI driver sees an error state in the register, and turns
off the UHCI controller.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230720072950.20198-1-olaf@aepfle.de>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity points out (CID 1513106, 1513107) that MemoryListener is a
192 byte struct which we are passing around by value. Switch to
passing a const pointer into xen_register_ioreq() and then to
xen_do_ioreq_register(). We can also make the file-scope
MemoryListener variables const, since nothing changes them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230718101057.1110979-1-peter.maydell@linaro.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Commit 1898293990 ("xen-block: Use specific blockdev driver")
introduced a new error path, without taking care of allocated
resources.
So only allocate the qdicts after the error check, and free both
`filename` and `driver` when we are about to return and thus taking
care of both success and error path.
Coverity only spotted the leak of qdicts (*_layer variables).
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: Coverity CID 1508722, 1398649
Fixes: 1898293990 ("xen-block: Use specific blockdev driver")
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230704171819.42564-1-anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity was unhappy (CID 1508359) because we didn't check the return of
init_walk_op() in transaction_commit(), despite doing so at every other
call site.
Strictly speaking, this is a false positive since it can never fail. It
only fails for invalid user input (transaction ID or path), and both of
those are hard-coded to known sane values in this invocation.
But Coverity doesn't know that, and neither does the casual reader of the
code.
Returning an error here would be weird, since the transaction *is*
committed by this point; all the walk_op is doing is firing watches on
the newly-committed changed nodes. So make it a g_assert(!ret), since
it really should never happen.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20076888f6bdf06a65aafc5cf954260965d45b97.camel@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Use the stl/ldl pci dma api for writing/reading doorbells. This removes
the explicit endian conversions.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Apache license is considered by some to be not compatible
with GPLv2+. Since QEMU as combined work is GPLv2-only,
these two files should be made compatible.
Reported-by: "Daniel P. Berrangé" <berrange@redhat.com>
Link: https://lore.kernel.org/qemu-devel/ZEpKXncC%2Fe6FKRe9@redhat.com/
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-By: canokeys.org (http://canokeys.org) <contact@canokeys.org>
Acked-by: YuanYang Meng <mkfssion@mkfssion.com>
Signed-off-by: Hongren (Zenithal) Zheng <i@zenithal.me>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
hw/sd/sdhci: Default I/O ops to little endian
hw/mips/loongson3-virt: Only use default USB if available
hw/char/escc: Implement loopback mode to allow self-testing
target/mips: Avoid overruns and shifts by negative number
target/sparc: Handle FPRS correctly on big-endian hosts
target/tricore: Rename tricore_feature to avoid clash with libcapstone
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmS/4ksACgkQ4+MsLN6t
wN6OSg//cZY9C6fRXNNaIqkmnhjbaV6KLtjE7mOKp0RUyh3aN0dtTwWIjdJc0O5C
iipHESYhcbHTiN/TxK0zXg4KgtKmtwqGsa3QTXGdTlSkTY/dMNioSpb7p82becu0
fhCvGRLJ97j7/mhebiBNT/urrcG5h3n7CjA5IoFMMA4f+cajsGZHwmq5TTzc2ehy
4FuchjFUw+cgqU1peNYoqt2dfnxFg0EgKBSRikl8MyPf9lFzTlXOKbgd+qppG6hI
2fAUHyMqBkU22sAoK0eB0077LjgjPPQfmn8UPGkpGD5QZQcvBRNArg4fyHxCKTS7
zOsO1Qc+4D2l2RJlIHgct2pmcHdT29TlTn2T4Lg900Hm09KelZh1XF+1BemCC13z
cGWjPcYozvGFFiHlhazINtbGpB6XaP/Z3OwroRHRn+Mn3ss+FaU+j/p+4YlEVyFi
4yoEyjhNma6/hssmstifSQsaOf6XthzpS+XdKNB6G1b2WuRSc1Z59b2gcPBTwbXY
B52lfI61nzSrP9pLuS8c/6hQXQvADIEndeWEcWZ50h3WW2Cemj9jTDVgfjWC4Vg9
wV2U6NeTr+g54cSU5vcKiZrqsQHUoLiKbZFRJkXF7EEMbOErIQnyIS5l8xf71Pay
YPxuPf1VprRiR07d+ZaA+wmEaBxLCUPEl1CEuu5NPVA9S4yIIWE=
=F+Wb
-----END PGP SIGNATURE-----
Merge tag 'misc-fixes-20230725' of https://github.com/philmd/qemu into staging
Misc patches queue
hw/sd/sdhci: Default I/O ops to little endian
hw/mips/loongson3-virt: Only use default USB if available
hw/char/escc: Implement loopback mode to allow self-testing
target/mips: Avoid overruns and shifts by negative number
target/sparc: Handle FPRS correctly on big-endian hosts
target/tricore: Rename tricore_feature to avoid clash with libcapstone
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmS/4ksACgkQ4+MsLN6t
# wN6OSg//cZY9C6fRXNNaIqkmnhjbaV6KLtjE7mOKp0RUyh3aN0dtTwWIjdJc0O5C
# iipHESYhcbHTiN/TxK0zXg4KgtKmtwqGsa3QTXGdTlSkTY/dMNioSpb7p82becu0
# fhCvGRLJ97j7/mhebiBNT/urrcG5h3n7CjA5IoFMMA4f+cajsGZHwmq5TTzc2ehy
# 4FuchjFUw+cgqU1peNYoqt2dfnxFg0EgKBSRikl8MyPf9lFzTlXOKbgd+qppG6hI
# 2fAUHyMqBkU22sAoK0eB0077LjgjPPQfmn8UPGkpGD5QZQcvBRNArg4fyHxCKTS7
# zOsO1Qc+4D2l2RJlIHgct2pmcHdT29TlTn2T4Lg900Hm09KelZh1XF+1BemCC13z
# cGWjPcYozvGFFiHlhazINtbGpB6XaP/Z3OwroRHRn+Mn3ss+FaU+j/p+4YlEVyFi
# 4yoEyjhNma6/hssmstifSQsaOf6XthzpS+XdKNB6G1b2WuRSc1Z59b2gcPBTwbXY
# B52lfI61nzSrP9pLuS8c/6hQXQvADIEndeWEcWZ50h3WW2Cemj9jTDVgfjWC4Vg9
# wV2U6NeTr+g54cSU5vcKiZrqsQHUoLiKbZFRJkXF7EEMbOErIQnyIS5l8xf71Pay
# YPxuPf1VprRiR07d+ZaA+wmEaBxLCUPEl1CEuu5NPVA9S4yIIWE=
# =F+Wb
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 25 Jul 2023 15:55:07 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'misc-fixes-20230725' of https://github.com/philmd/qemu:
target/tricore: Rename tricore_feature
target/sparc: Handle FPRS correctly on big-endian hosts
target/mips: Avoid shift by negative number in page_table_walk_refill()
target/mips: Pass directory/leaf shift values to walk_directory()
target/mips/mxu: Avoid overrun in gen_mxu_q8adde()
target/mips/mxu: Avoid overrun in gen_mxu_S32SLT()
target/mips/mxu: Replace magic array size by its definition
hw/char/escc: Implement loopback mode
hw/mips: Improve the default USB settings in the loongson3-virt machine
hw/sd/sdhci: Do not force sdhci_mmio_*_ops onto all SD controllers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change is cosmetic. A comment is added explaining why we need to check for
the availability of function 0 when we hotplug a device.
CC: mst@redhat.com
CC: mjt@tls.msk.ru
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The firmware of the m68k next-cube machine uses the loopback mode
for self-testing the hardware and currently fails during this step.
By implementing the loopback mode, we can make the firmware pass
to the next step.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230716153519.31722-1-huth@tuxfamily.org>
It's possible to compile QEMU without the USB devices (e.g. when using
"--without-default-devices" as option for the "configure" script).
To be still able to run the loongson3-virt machine in default mode with
such a QEMU binary, we have to check here for the availability of the
OHCI controller first before instantiating the USB devices.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230714104903.284845-1-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Since commit c0a55a0c9d "hw/sd/sdhci: Support big endian SD host controller
interfaces" sdhci_common_realize() forces all SD card controllers to use either
sdhci_mmio_le_ops or sdhci_mmio_be_ops, depending on the "endianness" property.
However, there are device models which use different MMIO ops: TYPE_IMX_USDHC
uses usdhc_mmio_ops and TYPE_S3C_SDHCI uses sdhci_s3c_mmio_ops.
Forcing sdhci_mmio_le_ops breaks SD card handling on the "sabrelite" board, for
example. Fix this by defaulting the io_ops to little endian and switch to big
endian in sdhci_common_realize() only if there is a matchig big endian variant
available.
Fixes: c0a55a0c9d ("hw/sd/sdhci: Support big endian SD host controller
interfaces")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <20230709080950.92489-1-shentey@gmail.com>
The implementation of the SMMUv3 has multiple places where it reads a
data structure from the guest and directly operates on it without
doing a guest-to-host endianness conversion. Since all SMMU data
structures are little-endian, this means that the SMMU doesn't work
on a big-endian host. In particular, this causes the Avocado test
machine_aarch64_virt.py:Aarch64VirtMachine.test_alpine_virt_tcg_gic_max
to fail on an s390x host.
Add appropriate byte-swapping on reads and writes of guest in-memory
data structures so that the device works correctly on big-endian
hosts.
As part of this we constrain queue_read() to operate only on Cmd
structs and queue_write() on Evt structs, because in practice these
are the only data structures the two functions are used with, and we
need to know what the data structure is to be able to byte-swap its
parts correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230717132641.764660-1-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
* Fix LMUL check to use VLEN
* Fix typo field in NUMA error_report
* check priv_ver before auto-enable zca/zcd/zcf
* Fix disas output of upper immediates
* tidy CPU firmware section
-----BEGIN PGP SIGNATURE-----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=MOsI
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230719-1' of https://github.com/alistair23/qemu into staging
Fourth RISC-V PR for 8.1
* Fix LMUL check to use VLEN
* Fix typo field in NUMA error_report
* check priv_ver before auto-enable zca/zcd/zcf
* Fix disas output of upper immediates
* tidy CPU firmware section
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmS3akMACgkQr3yVEwxT
# gBPQ/BAArrieEkrRco3tIQJFZqTLfII28M0cYdwN+gjMAkL6RlauCh5yKkc+gsGy
# bhhpr0AE+EzrjKfJgdyMQe2ZH08WEpoAfJHAmLTSm2ktgIlnDAjyJtVksZ3FSwfG
# MRK3v0CChyOav3EfDZzK9jcaXeaSSfjCIG8JW3enoZxf2TnpoXlsCIQdRTnMw7Um
# C73BWoOGOfixFehywHBnkkAPo/nkQPofELrRKNTlefAIsH1RcgYw+s3IgCIuYxJN
# zCjM1y6ye1aiaQhKcNJiLoiP4Eq2R6vUuL8RKWkXqTP3QBZUqKMPnRVgI+W0qRAj
# 9DS+l37zMdxytovQ4gmIqnENT8ty9bholOtWM8nI54subJBplQhkRednG3RBFYjH
# hqbsakcHfE1lyyNI7WoBpO8UMtnOad6eBNmMOM48VduSdNuBZN3ksoRVomnJTlCY
# nq1ZdteywHEZ3uBqk3k/4yzKH+jLj0McPz5FswxsMIGScVjd6H8rMYmM95r1He4k
# YTJ8GwnOTBs1tFxOz5DaM3BVfq5hrzB0SbpDHMOdQHNXnqkyfvSd/QWeXfnY09Ux
# kbNvSpzjn7wWRSP7s4KMcTmas4oGtPS2dheREB/gmoC1ubrfuhbzduDNXJt+omuC
# GDcn9cpouyE/Vp/358PuEe1gW9GFMH0CbYBJ66P0hI/76iPfwLY=
# =MOsI
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 19 Jul 2023 05:44:51 BST
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20230719-1' of https://github.com/alistair23/qemu:
target/riscv: Fix LMUL check to use VLEN
hw/riscv: Fix typo field in error_report
target/riscv/cpu.c: check priv_ver before auto-enable zca/zcd/zcf
riscv/disas: Fix disas output of upper immediates
docs/system/target-riscv.rst: tidy CPU firmware section
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 2fda0726e5 ("hw/nvme: fix missing endian conversions for
doorbell buffers"), we fixed shadow doorbells for big-endian guests
running on little endian hosts. But I did not fix little-endian guests
on big-endian hosts. Fix this.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1765
Fixes: 3f7fe8de3d ("hw/nvme: Implement shadow doorbell buffer support")
Cc: qemu-stable@nongnu.org
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
"smp.cpus" means the number of online CPUs and "smp.max_cpus" means the
total number of CPUs.
riscv_numa_get_default_cpu_node_id() checks "smp.cpus" and the
"available CPUs" description in the next error message also indicates
online CPUs.
So report "smp.cpus" in error_report() instand of "smp.max_cpus".
Since "smp.cpus" is "unsigned int", use "%u".
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230718080712.503333-1-zhao1.liu@linux.intel.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If QEMU is built with --without-default-devices, the s390-flic-kvm
device is missing and QEMU aborts when started with the KVM accelerator.
Make sure it's available by selecting S390_FLIC_KVM in Kconfig.
Consequently, this also fixes an abort in tests/qtest/migration-test.
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20230711151440.716822-1-clg@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Replace 'width' and 'height' in QemuDmaBuf with 'backing_widht'
and 'backing_height' as these commonly indicate the size of the
whole surface (e.g. guest's Xorg extended display). Then use
'width' and 'height' for sub region in there (e.g. guest's
scanouts).
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20230713040444.32267-1-dongwon.kim@intel.com>
The primary guest scanout shows the booting screen right after reboot
but additional guest displays (i.e. max_ouptuts > 1) will keep displaying
the old frames until the guest virtio gpu driver gets initialized, which
could cause some confusion. A better way is to to replace the surface with
a place holder that tells the display is not active during the reset of
virtio-gpu device.
And to immediately update the surface with the place holder image after
the switch, displaychangelistener_gfx_switch needs to be called with
'update == TRUE' in dpy_gfx_replace_surface when the new surface is NULL.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20230627224451.11739-1-dongwon.kim@intel.com>
Commit 9462ff4695 ("virtio-gpu/win32: allocate shareable 2d
resources/images") introduces a division, which can lead to crashes when
"height" is 0.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1744
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Add a check in the bit-set operation to write the backstore
only if the affected bit is 0 before.
With this in place, there will be no need for callers to
do the checking in order to avoid unnecessary writes.
Signed-off-by: Tong Ho <tong.ho@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This extends the slots of xhci to 64, since the default xhci_sysbus
just supports one slot.
Signed-off-by: Wang Yuquan <wangyuquan1236@phytium.com.cn>
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230710063750.473510-2-wangyuquan1236@phytium.com.cn
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ppi command line option for the TIS device on sysbus never worked
and caused an immediate segfault. Remove support for it since it also
needs support in the firmware and needs testing inside the VM.
Reproducer with the ppi=on option passed:
qemu-system-aarch64 \
-machine virt,gic-version=3 \
-m 4G \
-nographic -no-acpi \
-chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-device,tpmdev=tpm0,ppi=on
[...]
Segmentation fault (core dumped)
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230713171955.149236-1-stefanb@linux.ibm.com
scsi_clear_unit_attention() now only handles REPORTED LUNS DATA HAS
CHANGED.
This only happens when we handle REPORT LUNS commands, so let's rename
the function in scsi_clear_reported_luns_changed() and call it only in
scsi_target_emulate_report_luns().
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-ID: <20230712134352.118655-4-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous commit moved the unit attention clearing when we create
the request. So now we can clean scsi_clear_unit_attention() to handle
only the case of the REPORT LUNS command: this is the only case in
which a UNIT ATTENTION is cleared without having been reported.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-ID: <20230712134352.118655-3-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs") split
calls to scsi_req_new() and scsi_req_enqueue() in the virtio-scsi device.
No ill effects were observed until commit 8cc5583abe ("virtio-scsi: Send
"REPORTED LUNS CHANGED" sense data upon disk hotplug events") added a
unit attention that was easy to trigger with device hotplug and
hot-unplug.
Because the two calls were separated, all requests in the batch were
prepared calling scsi_req_new() to report a sense. The first one
submitted would report the right sense and reset it to NO_SENSE, while
the others reported CHECK_CONDITION with no sense data. This caused
SCSI errors in Linux.
To solve this issue, let's fetch the unit attention as early as possible
when we prepare the request, so that only the first request in the batch
will use the unit attention SCSIReqOps and the others will not report
CHECK CONDITION.
Fixes: 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs")
Fixes: 8cc5583abe ("virtio-scsi: Send "REPORTED LUNS CHANGED" sense data upon disk hotplug events")
Reported-by: Thomas Huth <thuth@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2176702
Co-developed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-ID: <20230712134352.118655-2-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is useful to extend the number of available PCIe devices to KVM guests
for passthrough scenarios and also to expose these models to a different
(big endian) architecture. Introduce a new config PCIE_DEVICES to select
models, Intel Ethernet adapters and one USB controller. These devices all
support MSI-X which is a requirement on s390x as legacy INTx are not
supported.
Cc: Matthew Rosato <mjrosato@linux.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20230712080146.839113-1-clg@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to the 82371FB documentation (82371FB.pdf, 2.3.9. BMIBA-BUS
MASTER INTERFACE BASE ADDRESS REGISTER, April 1997), the register is
32bit wide. To properly reset it to default values, all 32bit need to be
cleared. Bit #0 "Resource Type Indicator (RTE)" needs to be enabled.
The initial change wrote just the lower 8 bit, leaving parts of the "Bus
Master Interface Base Address" address at bit 15:4 unchanged.
Fixes: e6a71ae327 ("Add support for 82371FB (Step A1) and Improved support for 82371SB (Function 1)")
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230712074721.14728-1-olaf@aepfle.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The main loop thread can consume 100% CPU when using --device
virtio-blk-pci,iothread=<iothread>. ppoll() constantly returns but
reading virtqueue host notifiers fails with EAGAIN. The file descriptors
are stale and remain registered with the AioContext because of bugs in
the virtio-blk dataplane start/stop code.
The problem is that the dataplane start/stop code involves drain
operations, which call virtio_blk_drained_begin() and
virtio_blk_drained_end() at points where the host notifier is not
operational:
- In virtio_blk_data_plane_start(), blk_set_aio_context() drains after
vblk->dataplane_started has been set to true but the host notifier has
not been attached yet.
- In virtio_blk_data_plane_stop(), blk_drain() and blk_set_aio_context()
drain after the host notifier has already been detached but with
vblk->dataplane_started still set to true.
I would like to simplify ->ioeventfd_start/stop() to avoid interactions
with drain entirely, but couldn't find a way to do that. Instead, this
patch accepts the fragile nature of the code and reorders it so that
vblk->dataplane_started is false during drain operations. This way the
virtio_blk_drained_begin() and virtio_blk_drained_end() calls don't
touch the host notifier. The result is that
virtio_blk_data_plane_start() and virtio_blk_data_plane_stop() have
complete control over the host notifier and stale file descriptors are
no longer left in the AioContext.
This patch fixes the 100% CPU consumption in the main loop thread and
correctly moves host notifier processing to the IOThread.
Fixes: 1665d9326f ("virtio-blk: implement BlockDevOps->drained_begin()")
Reported-by: Lukáš Doktor <ldoktor@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Lukas Doktor <ldoktor@redhat.com>
Message-id: 20230704151527.193586-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Let's support device unplug by forwarding the unplug_request_check()
callback to the virtio-mem device.
Further, disallow changing the requested-size once an unplug request is
pending.
Disallowing requested-size changes handles corner cases such as
(1) pausing the VM (2) requesting device unplug and (3) adjusting the
requested size. If the VM would plug memory (due to the requested size
change) before processing the unplug request, we would be in trouble.
Message-ID: <20230711153445.514112-8-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
In many cases, blindly unplugging a virtio-mem device is problematic. We
can only safely remove a device once:
* The guest is not expecting to be able to read unplugged memory
(unplugged-inaccessible == on)
* The virtio-mem device does not have memory plugged (size == 0)
* The virtio-mem device does not have outstanding requests to the VM to
plug memory (requested-size == 0)
So let's add a callback to the virtio-mem device class to check for that.
We'll wire-up virtio-mem-pci next.
Message-ID: <20230711153445.514112-7-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's support unplug requests for virtio-md-pci devices that provide
a unplug_request_check() callback.
We'll wire that up for virtio-mem-pci next.
Message-ID: <20230711153445.514112-6-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
While we fence unplug requests from the outside, the VM can still
trigger unplug of virtio based memory devices, for example, in Linux
doing on a virtio-mem-pci device:
# echo 0 > /sys/bus/pci/slots/3/power
While doing that is not really expected to work without harming the
guest OS (e.g., removing a virtio-mem device while it still provides
memory), let's make sure that we properly handle it on the QEMU side.
We'll add support for unplugging of virtio-mem devices in some
configurations next.
Message-ID: <20230711153445.514112-5-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use our new helper functions. Note that virtio-pmem-pci is not
enabled for arm and, therefore, not compiled in.
Message-ID: <20230711153445.514112-4-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's factor out (un)plug handling, to be reused from arm/virt code.
Provide stubs for the case that CONFIG_VIRTIO_MD is not selected because
neither virtio-mem nor virtio-pmem is enabled. While this cannot
currently happen for x86, it will be possible for arm/virt.
Message-ID: <20230711153445.514112-3-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's add a new abstract "virtio memory device" type, and use it as
parent class of virtio-mem-pci and virtio-pmem-pci.
Message-ID: <20230711153445.514112-2-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
To achieve desired "x-ignore-shared" functionality, we should not
discard all RAM when realizing the device and not mess with
preallocation/postcopy when loading device state. In essence, we should
not touch RAM content.
As "x-ignore-shared" gets set after realizing the device, we cannot
rely on that. Let's simply skip discarding of RAM on incoming migration.
Note that virtio_mem_post_load() will call
virtio_mem_restore_unplugged() -- unless "x-ignore-shared" is set. So
once migration finished we'll have a consistent state.
The initial system reset will also not discard any RAM, because
virtio_mem_unplug_all() will not call virtio_mem_unplug_all() when no
memory is plugged (which is the case before loading the device state).
Note that something like VM templating -- see commit b17fbbe55c
("migration: allow private destination ram with x-ignore-shared") -- is
currently incompatible with virtio-mem and ram_block_discard_range() will
warn in case a private file mapping is supplied by virtio-mem.
For VM templating with virtio-mem, it makes more sense to either
(a) Create the template without the virtio-mem device and hotplug a
virtio-mem device to the new VM instances using proper own memory
backend.
(b) Use a virtio-mem device that doesn't provide any memory in the
template (requested-size=0) and use private anonymous memory.
Message-ID: <20230706075612.67404-5-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Already when starting QEMU we perform one system reset that ends up
triggering virtio_mem_unplug_all() with no actual memory plugged yet.
That, in turn will trigger ram_block_discard_range() and perform some
other actions that are not required in that case.
Let's optimize virtio_mem_unplug_all() for the case that no memory is
plugged. This will be beneficial for x-ignore-shared support as well.
Message-ID: <20230706075612.67404-3-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's avoid iterating over all devices and simply track it in the
DeviceMemoryState.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-11-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's move memory_device_check_addable() and basic checks out of
memory_device_get_free_addr() directly into memory_device_pre_plug().
Separating basic checks from address assignment is cleaner and
prepares for further changes.
As all memory device users now use memory_devices_init(), and that
function enforces that the size is 0, we can drop the check for an empty
region.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-10-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
There are no remaining users in the tree. Libvirt never used that
property and a quick internet search revealed no other users.
Further, we renamed that property already in commit f2ffbe2b7d
("pc: rename "hotplug memory" terminology to "device memory"") without
anybody complaining.
So let's just get rid of it.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-9-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We're already looking at machine->device_memory when calling
build_srat_memory(), so let's simply avoid going via
PC_MACHINE_DEVMEM_REGION_SIZE to get the size and rely on
machine->device_memory directly.
Once machine->device_memory is set, we know that the size > 0. The code now
looks much more similar the hw/arm/virt-acpi-build.c variant.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-8-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use our new helper and stop always allocating ms->device_memory.
Once allcoated, we're sure that the size > 0 and that the base was
initialized.
Adjust the code in pc_memory_init() to check for machine->device_memory
instead of pcmc->has_reserved_memory and machine->device_memory->base.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-7-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use our new helper. While at it, use VIRT_HIGHMEM_BASE.
Cc: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Cc: Song Gao <gaosong@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-6-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use our new helper and stop always allocating ms->device_memory.
There is no difference in common memory-device code anymore between
ms->device_memory being NULL or the size being 0. So we only have to
teach spapr code that ms->device_memory isn't always around.
We can now modify two maxram_size checks to rely on ms->device_memory
for detecting whether we have memory devices.
Cc: Daniel Henrique Barboza <danielhb413@gmail.com>
Cc: "Cédric Le Goater" <clg@kaod.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Greg Kurz <groug@kaod.org>
Cc: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-5-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use our new helper. We'll add the subregion to system RAM now
earlier. That shouldn't matter, because the system RAM memory region should
already be alive at that point.
Cc: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-4-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's intrduce a new helper that we will use to replace existing memory
device setup code during machine initialization. We'll enforce that the
size has to be > 0.
Once all machines were converted, we'll only allocate ms->device_memory
if the size > 0.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-3-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's unify the error messages, such that we can simply stop allocating
ms->device_memory if the size would be 0 (and there are no memory
devices ever).
The case of "not supported by the machine" should barely pop up either
way: if the machine doesn't support memory devices, it usually doesn't
call the pre_plug handler ...
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-2-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
vhost-user-gpu: edid
vhost-user-scmi device
vhost-vdpa: _F_CTRL_RX and _F_CTRL_RX_EXTRA support for svq
cleanups, fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmSsjYMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp2vYH/20u6TAMssE/UAJoUU0ypbJkbHjDqiqDeuZN
qDYazLUWIJTUbDnSfXAiRcdJuukEpEFcoHa9O6vgFE/SNod51IrvsJR9CbZxNmk6
D+Px9dkMckDE/yb8f6hhcHsi7/1v04I0oSXmJTVYxWSKQhD4Km6x8Larqsh0u4yd
n6laZ+VK5H8sk6QvI5vMz+lYavACQVryiWV/GAigP21B0eQK79I5/N6y0q8/axD5
cpeTzUF+m33SfLfyd7PPmibCQFYrHDwosynSnr3qnKusPRJt2FzWkzOiZgbtgE2L
UQ/S4sYTBy8dZJMc0wTywbs1bSwzNrkQ+uS0v74z9wCUYTgvQTA=
=RsOh
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
pc,pci,virtio: cleanups, fixes, features
vhost-user-gpu: edid
vhost-user-scmi device
vhost-vdpa: _F_CTRL_RX and _F_CTRL_RX_EXTRA support for svq
cleanups, fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmSsjYMPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp2vYH/20u6TAMssE/UAJoUU0ypbJkbHjDqiqDeuZN
# qDYazLUWIJTUbDnSfXAiRcdJuukEpEFcoHa9O6vgFE/SNod51IrvsJR9CbZxNmk6
# D+Px9dkMckDE/yb8f6hhcHsi7/1v04I0oSXmJTVYxWSKQhD4Km6x8Larqsh0u4yd
# n6laZ+VK5H8sk6QvI5vMz+lYavACQVryiWV/GAigP21B0eQK79I5/N6y0q8/axD5
# cpeTzUF+m33SfLfyd7PPmibCQFYrHDwosynSnr3qnKusPRJt2FzWkzOiZgbtgE2L
# UQ/S4sYTBy8dZJMc0wTywbs1bSwzNrkQ+uS0v74z9wCUYTgvQTA=
# =RsOh
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 11 Jul 2023 12:00:19 AM BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (66 commits)
vdpa: Allow VIRTIO_NET_F_CTRL_RX_EXTRA in SVQ
vdpa: Restore packet receive filtering state relative with _F_CTRL_RX_EXTRA feature
vdpa: Allow VIRTIO_NET_F_CTRL_RX in SVQ
vdpa: Avoid forwarding large CVQ command failures
vdpa: Accessing CVQ header through its structure
vhost: Fix false positive out-of-bounds
vdpa: Restore packet receive filtering state relative with _F_CTRL_RX feature
vdpa: Restore MAC address filtering state
vdpa: Use iovec for vhost_vdpa_net_load_cmd()
pcie: Specify 0 for ARI next function numbers
pcie: Use common ARI next function number
include/hw/virtio: document some more usage of notifiers
include/hw/virtio: add kerneldoc for virtio_init
include/hw/virtio: document virtio_notify_config
hw/virtio: fix typo in VIRTIO_CONFIG_IRQ_IDX comments
include/hw: document the device_class_set_parent_* fns
include: attempt to document device_class_set_props
vdpa: Fix possible use-after-free for VirtQueueElement
pcie: Add hotplug detect state register to cmask
virtio-iommu: Rework the traces in virtio_iommu_set_page_size_mask()
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
QEMU uses vhost_svq_translate_addr() to translate addresses
between the QEMU's virtual address and the SVQ IOVA. In order
to validate this translation, QEMU checks whether the translated
range falls within the mapped range.
Yet the problem is that, the value of `needle_last`, which is calculated
by `needle.translated_addr + iovec[i].iov_len`, should represent the
exclusive boundary of the translated range, rather than the last
inclusive addresses of the range. Consequently, QEMU fails the check
when the translated range matches the size of the mapped range.
This patch solves this problem by fixing the `needle_last` value to
the last inclusive address of the translated range.
Note that this bug cannot be triggered at the moment, because QEMU
is unable to translate such a big range due to the truncation of
the CVQ command in vhost_vdpa_net_handle_ctrl_avail().
Fixes: 34e3c94eda ("vdpa: Add custom IOTLB translations to SVQ")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <ee31c5420ffc8e6a29705ddd30badb814ddbae1d.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
