Check for hot plug capability earlier to avoid removing devices attached
during the initialization process.
Run qemu with an unattached drive:
-drive file=$FILE,if=none,id=drive0 \
-device pcie-root-port,id=rp0,slot=3,bus=pcie.0,hotplug=off
Hotplug a block device:
device_add virtio-blk-pci,id=blk0,drive=drive0,bus=rp0
If hotplug fails on plug_cb, drive0 will be deleted.
Fixes: 0501e1aa1d ("hw/pci/pcie: Forbid hot-plug if it's disabled on the slot")
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Julia Suvorova <jusual@redhat.com>
Message-Id: <20200604125947.881210-1-jusual@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The file tests/qtest/bios-tables-test-allowed-diff.h is currently only
assigned to the qtest section according MAINTAINERS. However, this file
normally only gets updated when the ACPI tables changed - something the
qtest maintainers don't have much clue of. Thus this file should rather
be assigned to the ACPI maintainers instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200607052022.12222-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add support for free page reporting. The idea is to function very similar
to how the balloon works in that we basically end up madvising the page as
not being used. However we don't really need to bother with any deflate
type logic since the page will be faulted back into the guest when it is
read or written to.
This provides a new way of letting the guest proactively report free
pages to the hypervisor, so the hypervisor can reuse them. In contrast to
inflate/deflate that is triggered via the hypervisor explicitly.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Message-Id: <20200527041407.12700.73735.stgit@localhost.localdomain>
We need to make certain to advertise support for page poison reporting if
we want to actually get data on if the guest will be poisoning pages.
Add a value for reporting the poison value being used if page poisoning is
enabled in the guest. With this we can determine if we will need to skip
free page reporting when it is enabled in the future.
The value currently has no impact on existing balloon interfaces. In the
case of existing balloon interfaces the onus is on the guest driver to
reapply whatever poison is in place.
When we add free page reporting the poison value is used to determine if
we can perform in-place page reporting. The expectation is that a reported
page will already contain the value specified by the poison, and the
reporting of the page should not change that value.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Message-Id: <20200527041400.12700.33251.stgit@localhost.localdomain>
We took a reference when realizing, so let's drop that reference when
unrealizing.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Fixes: c13c4153f7 ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Cc: qemu-stable@nongnu.org
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200520100439.19872-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Checking against guest features is wrong. We allocated data structures
based on host features. We can rely on "free_page_bh" as an indicator
whether to un-do stuff instead.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Fixes: c13c4153f7 ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Cc: qemu-stable@nongnu.org
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200520100439.19872-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In case we don't have an iothread, we mark the feature as abscent but
still add the queue. 'free_page_bh' remains set to NULL.
qemu-system-i386 \
-M microvm \
-nographic \
-device virtio-balloon-device,free-page-hint=true \
-nographic \
-display none \
-monitor none \
-serial none \
-qtest stdio
Doing a "write 0xc0000e30 0x24
0x030000000300000003000000030000000300000003000000030000000300000003000000"
We will trigger a SEGFAULT. Let's move the check and bail out.
While at it, move the static initializations to instance_init().
free_page_report_status and block_iothread are implicitly set to the
right values (0/false) already, so drop the initialization.
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Fixes: c13c4153f7 ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Cc: qemu-stable@nongnu.org
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200520100439.19872-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
TPM2, DSDT tables were generated using
tests/data/acpi/rebuild-expected-aml.sh
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20200609125409.24179-6-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Test tables specific to the TPM-TIS instantiation.
The TPM2 is added in the framework. Also the DSDT
is updated with the TPM. The new function should be
be usable for CRB as well, later one.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200609125409.24179-5-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
bios-tables-test executes SeaBIOS. Indeed FW is needed to
fetch tables from QEMU and put them into the guest RAM. Also
the FW patches cross table pointers. At some point, SeaBIOS
ends up calling the TPM2_CC_HierarchyControl command with
TPM2_ST_SESSIONS tag, most probably steming from
tpm_set_failure/tpm20_hierarchycontrol SeaBIOS call path.
This causes an assert() in the qtest tpm emulation code.
As the goal here is not to boot SeaBIOS completely but just
let it grab the ACPI tables and consolidate them, let's just
remove the assert().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200609125409.24179-4-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add placeholders for TPM and DSDT reference tables for
Q35 TPM-TIS tests and ignore them for the time being.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200609125409.24179-3-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Include sockets and channel headers to that the header is
self-contained.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20200609125409.24179-2-eric.auger@redhat.com>
Add a TPM2 ACPI table if a TPM2.0 sysbus device has been
dynamically instantiated.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200601095737.32671-4-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We plan to build the TPM2 table on ARM too. In order to reuse the
generation code, let's move build_tpm2() to aml-build.c.
No change in the implementation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200601095737.32671-3-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In preparation of its move to the generic acpi code,
let's convert build_tpm2() to use build_append API. This
latter now is prefered in place of direct ACPI struct field
settings with manual endianness conversion.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200601095737.32671-2-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Do not build a TCPA table for TPM 2 anymore but create the log area when
building the TPM2 table. The TCPA table is only needed for TPM 1.2.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Also adds support for multiple LPT devices.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200515150421.25479-8-kraxel@redhat.com>
The _STA method dates back to the days where we had a static DSDT. The
device is listed in the DSDT table unconditionally and the _STA method
checks a bit in the isa bridge pci config space to figure whenever a
given is isa device is present or not, then evaluates to 0x0f (present)
or 0x00 (absent).
These days the DSDT is generated by qemu anyway, so if a device is not
present we can simply drop it from the DSDT instead.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200515150421.25479-7-kraxel@redhat.com>
The code uses the isa_serial_io array to figure what the device uid is.
Side effect is that acpi antries are not limited to port 1+2 any more,
we'll also get entries for ports 3+4.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200515150421.25479-6-kraxel@redhat.com>
The _STA method dates back to the days where we had a static DSDT. The
device is listed in the DSDT table unconditionally and the _STA method
checks a bit in the isa bridge pci config space to figure whenever a
given is isa device is present or not, then evaluates to 0x0f (present)
or 0x00 (absent).
These days the DSDT is generated by qemu anyway, so if a device is not
present we can simply drop it from the DSDT instead.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200515150421.25479-5-kraxel@redhat.com>
Use a single io range for _CRS instead of two,
following what real hardware does.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200515150421.25479-4-kraxel@redhat.com>
Update expected SRAT files for the change to account for NVDIMM NUMA
nodes in the SRAT.
AML diffs:
tests/data/acpi/pc/SRAT.dimmpxm:
Message-Id: <20200606000911.9896-4-vishal.l.verma@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
NVDIMMs can belong to their own proximity domains, as described by the
NFIT. In such cases, the SRAT needs to have Memory Affinity structures
in the SRAT for these NVDIMMs, otherwise Linux doesn't populate node
data structures properly during NUMA initialization. See the following
for an example failure case.
https://lore.kernel.org/linux-nvdimm/20200416225438.15208-1-vishal.l.verma@intel.com/
Introduce a new helper, nvdimm_build_srat(), and call it for both the
i386 and arm versions of 'build_srat()' to augment the SRAT with
memory affinity information for NVDIMMs.
The relevant command line options to exercise this are below. Nodes 0-1
contain CPUs and regular memory, and nodes 2-3 are the NVDIMM address
space.
-object memory-backend-ram,id=mem0,size=2048M
-numa node,nodeid=0,memdev=mem0,
-numa cpu,node-id=0,socket-id=0
-object memory-backend-ram,id=mem1,size=2048M
-numa node,nodeid=1,memdev=mem1,
-numa cpu,node-id=1,socket-id=1
-numa node,nodeid=2,
-object memory-backend-file,id=nvmem0,share,mem-path=nvdimm-0,size=16384M,align=1G
-device nvdimm,memdev=nvmem0,id=nv0,label-size=2M,node=2
-numa node,nodeid=3,
-object memory-backend-file,id=nvmem1,share,mem-path=nvdimm-1,size=16384M,align=1G
-device nvdimm,memdev=nvmem1,id=nv1,label-size=2M,node=3
Cc: Jingqi Liu <jingqi.liu@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jingqi Liu <jingqi.liu@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Message-Id: <20200606000911.9896-3-vishal.l.verma@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In anticipation of a change to the SRAT generation in qemu, add the AML
file to diffs-allowed.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Message-Id: <20200606000911.9896-2-vishal.l.verma@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI spec says:
For all accesses to MSI-X Table and MSI-X PBA fields, software must use
aligned full DWORD or aligned full QWORD transactions; otherwise, the
result is undefined.
However, since MSI-X was converted to use memory API, QEMU
started blocking qword transactions, only allowing DWORD
ones. Guests do not seem to use QWORD accesses, but let's
be spec compliant.
Fixes: 95524ae8dc ("msix: convert to memory API")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In Makefile.objs, the ui/ directory is restricted to system-mode:
43 ifeq ($(CONFIG_SOFTMMU),y)
...
65 common-obj-y += ui/
66 common-obj-m += ui/
...
82 endif # CONFIG_SOFTMMU
Restrict the ui/ stub added in commit 2df9f5718d to only build
it for system-mode emulation.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200522172510.25784-14-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These stubs are not required when configured with --disable-system.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200522172510.25784-7-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These objects are not required when configured with --disable-system.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200522172510.25784-6-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In the next commit we are going to remove some objects from the
util-obj-y variable (objects which are not used by user-mode,
when configured with --disable-system).
Then some system-mode tests are going to fail, due to the missing
objects:
$ make check-unit -k
LINK tests/test-iov
/usr/bin/ld: tests/test-iov.o: in function `iov_from_buf':
include/qemu/iov.h:49: undefined reference to `iov_from_buf_full'
make: *** [rules.mak:124: tests/test-iov] Error 1
LINK tests/test-timed-average
/usr/bin/ld: tests/test-timed-average.o: in function `account':
tests/test-timed-average.c:27: undefined reference to `timed_average_account'
make: *** [rules.mak:124: tests/test-timed-average] Error 1
LINK tests/test-util-filemonitor
/usr/bin/ld: tests/test-util-filemonitor.o: in function `qemu_file_monitor_test_event_loop':
tests/test-util-filemonitor.c:83: undefined reference to `main_loop_wait'
make: *** [rules.mak:124: tests/test-util-filemonitor] Error 1
LINK tests/test-util-sockets
/usr/bin/ld: tests/test-util-sockets.o: in function `test_socket_fd_pass_name_good':
tests/test-util-sockets.c:91: undefined reference to `socket_connect'
make: *** [rules.mak:124: tests/test-util-sockets] Error 1
LINK tests/test-base64
/usr/bin/ld: tests/test-base64.o: in function `test_base64_good':
tests/test-base64.c:35: undefined reference to `qbase64_decode'
collect2: error: ld returned 1 exit status
make: *** [rules.mak:124: tests/test-base64] Error 1
LINK tests/test-bufferiszero
/usr/bin/ld: tests/test-bufferiszero.o: in function `test_1':
tests/test-bufferiszero.c:31: undefined reference to `buffer_is_zero'
make: *** [rules.mak:124: tests/test-bufferiszero] Error 1
make: Target 'check-unit' not remade because of errors.
Instead, restrict these tests to system-mode, by using the
$(CONFIG_SOFTMMU) variable.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200522172510.25784-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Avoid building TCG when building only tools:
./configure --enable-tools --disable-system --disable-user
This saves us from running the soft-float tests enabled since
commit 7617010250.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200522172510.25784-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Do not build the virtiofsd helper when configured with
--disable-system.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200522172510.25784-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Fixes: https://bugs.launchpad.net/bugs/1876373
This code path in mmap occurs when a page size is decreased with mremap. When a section of pages is shrunk, qemu calls mmap_reserve on the pages that were released. However, it has the diff operation reversed, subtracting the larger old_size from the smaller new_size. Instead, it should be subtracting the smaller new_size from the larger old_size. You can also see in the previous line of the change that this mmap_reserve call only occurs when old_size > new_size.
Bug: https://bugs.launchpad.net/qemu/+bug/1876373
Signed-off-by: Jonathan Marler <johnnymarler@gmail.com>
Reviewded-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200502161225.14346-1-johnnymarler@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Convert the insns in the one-register-and-immediate group to decodetree.
In the new decode, our asimd_imm_const() function returns a 64-bit value
rather than a 32-bit one, which means we don't need to treat cmode=14 op=1
as a special case in the decoder (it is the only encoding where the two
halves of the 64-bit value are different).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-10-peter.maydell@linaro.org
Convert the VCVT fixed-point conversion operations in the
Neon 2-regs-and-shift group to decodetree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-9-peter.maydell@linaro.org
