Many source files have doubled words (eg "the the", "to to",
and so on). Most of these can simply be removed, but a couple
were actual mis-spellings (eg "to to" instead of "to do").
There was even one triple word score "to to to" :-)
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Specify the upper limit of refcount_order to be 6 (that is,
refcount_bits = 64). Any larger value does not make much sense when all
offsets, sizes, cluster counts etc. "only" have a width of 64 bit as
well, and very large values would be very difficult to support.
Therefore, just cap it at the largest reasonable value.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A refblock entry may have a different size than 16 bits, it may even be
smaller than a byte. Correct the refcount_block_entries calculation
accordingly.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The current version of the qcow2 specification recommends to save the backing
file name in the end of the first cluster. It follows that the backing file
name can be saved somewhere in the image, but the first cluster, which
contradicts the current QEMU implementation.
The patch makes the backing file name required to be placed after the header
extensions in the first image cluster.
Signed-off-by: Maria Kustova <maria.k@catit.be>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The 'refcount_bits' term used in the description of refcount block entry is
not defined in the specification. The definition is added in the
'refcount_order' section where refcount_bits was used as 'width in bits'.
Signed-off-by: Maria Kustova <maria.k@catit.be>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The qcow2 specification does not explicitly state so far that every
snapshot table entry is aligned to 8 bytes. QEMU, in contrast, does this
alignment, thus it should be properly documented (which this patch
does).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds an incompatible bit indicating corruption to qcow2. Any image
with this bit set may not be written to unless for repairing (and
subsequently clearing the bit if the repair has been successful).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The lazy refcounts bit indicates that this image can take advantage of
the dirty bit and that refcount updates can be postponed.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The dirty bit will make it possible to perform lazy refcount updates,
where the image file is not kept consistent all the time. Upon opening
a dirty image file, it is necessary to perform a consistency check and
repair any incorrect refcounts.
Therefore the dirty bit must be an incompatible feature bit. We don't
want old programs accessing a file with stale refcounts.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This updates the qcow2 specification to cover version 3. It contains the
following changes:
- Added compatible/incompatible/auto-clear feature bits plus an optional
feature name table to allow useful error messages even if an older
version doesn't know some feature at all.
- Configurable refcount width. If you don't want to use internal
snapshots, make refcounts one bit and save cache space and I/O.
- Zero cluster flags. This allows discard even with a backing file that
doesn't contain zeros. It is also useful for copy-on-read/image
streaming, as you'll want to keep sparseness without accessing the
remote image for an unallocated cluster all the time.
- Fixed internal snapshot metadata to use 64 bit VM state size. You
can't save a snapshot of a VM with >= 4 GB RAM today.
- Extended internal snapshot metadata to contain the disk size, so that
resizing images that have snapshots can be allowed in the future.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds a description of the qcow2 file format to the docs/ directory.
Besides documenting what's there, which is never wrong, the document should
provide a good basis for the discussion of format extensions (called "qcow3"
in previous discussions)
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
