Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-ID: <20241103133412.73536-19-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Populate this read-only register with some arbitrary values which avoids
U-Boot's get_clocks() to hang().
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-ID: <20241103133412.73536-11-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When compiling a decompiled device tree blob created with dumpdtb, dtc complains
with:
/soc@e0000000/i2c@3000: incorrect #address-cells for I2C bus
/soc@e0000000/i2c@3000: incorrect #size-cells for I2C bus
Fix this by adding the missing device tree properties.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-ID: <20241103133412.73536-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add a utility function and use it to replace very similar
create_initial_mapping functions in 440 based machines.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Add booke206_set_tlb() utility function and use it to replace very
similar create_initial_mapping functions in e500 machines.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Currently any device tree passed with -dtb option in QEMU, was ignored
by the PowerNV code.
Read and pass the passed -dtb to the kernel, thus enabling easier
debugging with custom DTBs.
The existing behaviour when -dtb is 'not' passed, is preserved as-is.
But when a '-dtb' is passed, it completely overrides any dtb nodes or
changes QEMU might have done, such as '-append' arguments to the kernel
(which are mentioned in /chosen/bootargs in the dtb), hence add warning
when -dtb is being used
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Aditya Gupta <adityag@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The DPDES support for doorbell emulation and handling for KVM on PAPR
guests was added in Linux via [1]. Subsequently, a new GSB (Guest State
Buffer) element for DPDES was added in Linux; the same has been missing
in TCG L0 implementation. Add support for DPDES register's APIv2 GSB
element and required handling in `spapr_nested.c`.
Currently, booting a KVM guest inside a QEMU TCG guest fails with the
following crash. The crash occurs while handling the GUEST_RUN_VCPU
hcall made in TCG L0. In the hcall handling path, map_and_getset_state()
calls getset_state(), which, in turn, calls guest_state_request_check()
to validate the GSR (Guest State Request) elements. During this process,
guest_state_request_check() iterates over the GSR elements and receives
a NULL return code from guest_state_element_type_find() for the type
variable corresponding to the DPDES register's elemetn ID (which was
unknown to TCG L0). Subsequently, getset_state() returns H_P3,
ultimately leading to the hcall failure and causing the KVM guest to
crash.
KVM: unknown exit, hardware reason ffffffffffffffea
[ ... KVM register dump ... ]
Fix this by adding the required support in TCG L0 implementation of
APIv2.
[1] https://lore.kernel.org/all/20240605113913.83715-1-gautam@linux.ibm.com/
Fixes: 4a575f9a05 ("spapr: nested: Initialize the GSB elements lookup table.")
Suggested-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Amit Machhiwal <amachhiw@linux.ibm.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Add sPAPR CPU Core definition for Power11
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Aditya Gupta <adityag@linux.ibm.com>
Tested-by: Amit Machhiwal <amachhiw@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 0cac0f1b96 marked pseries-2.12 machines as deprecated
with reasons mentioned in its commit log.
Removing pseries-2.12 specific code with this patch.
While at it, also remove pre-3.0-migration hacks introduced for backward
compatibility which are now turned useless.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 0cac0f1b96 marked pseries-2.12 machines as deprecated
with reasons mentioned in its commit log.
Removing pseries-2.12-sxxm specific code with this patch.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.11 specific code with this patch.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.10 specific code with this patch for now.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.9 specific code with this patch for now.
While at it, also remove the pre-2.10 migration hacks which now become
obsolete.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.8 specific code with this patch for now.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.7 specific code with this patch for now.
While at it, also remove pre-2.8-migration and pci/mmio hacks introduced
for backward compatibility.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.6 specific code with this patch for now.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.5 specific code with this patch for now.
Also drop sPAPRMachineClass::use_ohci_by_default which is now useless.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.4 specific code with this patch for now.
While at it, also remove SpaprMachineClass::dr_lmb_enabled which is
now turned useless.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.3 specific code with this patch for now.
While at it, also remove the dynamic-reconfiguration option which was
introduced to disable it by default for legacy machines until pseries-2.3.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.2 specific code with this patch for now.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Commit 1392617d35 intended to tag pseries-2.1 - 2.11 machines as
deprecated with reasons mentioned in its commit log.
Removing pseries-2.1 specific code with this patch for now.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The BookE decrementer stops at 0, meaning that it won't decremented
towards "negative" values. However, the current logic is inverted: decr
is updated solely when the resulting value would be negative.
Signed-off-by: Clément Chigot <chigot@adacore.com>
Fixes: 8e0a5ac878 ("hw/ppc: Avoid decrementer rounding errors")
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The ADU LPC transfer-size field is 7 bits, but the supported sizes for
LPC access via ADU appear to be 1, 2, 4, 8. The data buffer could
overrun if firmware set an invalid size field, so add checks to reject
them with a message.
Cc: qemu-stable@nongnu.org
Reported-by: Cédric Le Goater <clg@redhat.com>
Resolves: Coverity CID 1558830
Fixes: 24bd283bcc ("ppc/pnv: Implement ADU access to LPC space")
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER8 does not have the ISA IRQ -> SERIRQ routing system of later
CPUs, instead all ISA IRQs are sent to the CPU via a single PSI
interrupt. There is a sanity check in the POWER8 case to ensure the
routing bits have not been set, because that would indicate a
programming error.
Those bits were incorrectly specified because of ppc bit numbering
fun. Coverity detected this as an always-zero expression.
Cc: qemu-stable@nongnu.org
Reported-by: Cédric Le Goater <clg@redhat.com>
Resolves: Coverity CID 1558829 (partially)
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The serirq routing table is split over two registers, the calculation
for the high irqs in the second register did not subtract the irq
offset. This was spotted by Coverity as a shift-by-negative. Fix this
and change the open-coded shifting and masking to use extract32()
function so it's less error-prone.
This went unnoticed because irqs >= 14 are not used in a standard
QEMU/OPAL boot, changing the first QEMU serial-isa irq to 14 to test
does demonstrate serial irqs aren't received, and that this change
fixes that.
Cc: qemu-stable@nongnu.org
Reported-by: Cédric Le Goater <clg@redhat.com>
Resolves: Coverity CID 1558829 (partially)
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
hw/char/serial currently contains the implementation of both TYPE_SERIAL and
TYPE_SERIAL_MM. According to serial_class_init(), TYPE_SERIAL is an internal
class while TYPE_SERIAL_MM is used by numerous machine types directly. Let's
move the latter into its own module which makes the dependencies more obvious
and the code more tidy.
The includes and the dependencies have been converted mechanically except in the
hw/char directories which were updated manually. The result was compile-tested.
Now, only hw/char makes direct use of TYPE_SERIAL:
# grep -r -e "select SERIAL" | grep -v SERIAL_
hw/char/Kconfig: select SERIAL
hw/char/Kconfig: select SERIAL
hw/char/Kconfig: select SERIAL
hw/char/Kconfig: select SERIAL
hw/char/Kconfig: select SERIAL
# grep -r -e "/serial\\.h"
include/hw/char/serial-mm.h:#include "hw/char/serial.h"
hw/char/serial-pci-multi.c:#include "hw/char/serial.h"
hw/char/serial.c:#include "hw/char/serial.h"
hw/char/serial-isa.c:#include "hw/char/serial.h"
hw/char/serial-pci.c:#include "hw/char/serial.h"
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Link: https://lore.kernel.org/r/20240905073832.16222-4-shentey@gmail.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The includes where updated based on compile errors. Now, the inclusion of the
header roughly matches Kconfig dependencies:
# grep -r -e "select SERIAL_ISA"
hw/ppc/Kconfig: select SERIAL_ISA
hw/isa/Kconfig: select SERIAL_ISA
hw/sparc64/Kconfig: select SERIAL_ISA
hw/i386/Kconfig: select SERIAL_ISA
hw/i386/Kconfig: select SERIAL_ISA # for serial_hds_isa_init()
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Link: https://lore.kernel.org/r/20240905073832.16222-3-shentey@gmail.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch is part of a series that moves towards a consistent use of
g_assert_not_reached() rather than an ad hoc mix of different
assertion mechanisms.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-ID: <20240919044641.386068-30-pierrick.bouvier@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch is part of a series that moves towards a consistent use of
g_assert_not_reached() rather than an ad hoc mix of different
assertion mechanisms.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-ID: <20240919044641.386068-13-pierrick.bouvier@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently, both qemu_devices_reset() and MachineClass::reset() use
ShutdownCause for the reason of the reset. However, the Resettable
interface uses ResetState, so ShutdownCause needs to be translated to
ResetType somewhere. Translating it qemu_devices_reset() makes adding
new reset types harder, as they cannot always be matched to a single
ShutdownCause here, and devices may need to check the ResetType to
determine what to reset and if to reset at all.
This patch moves this translation up in the call stack to
qemu_system_reset() and updates all MachineClass children to use the
ResetType instead.
Message-ID: <20240904103722.946194-2-jmarcin@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Juraj Marcin <jmarcin@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Since the "2 | 3+" expression can be simplified as "2+",
it is pointless to mention the GPLv3 license.
Add the corresponding SPDX identifier to remove all doubt.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
PowerMac is spelled as PowerMAC (Media Access Control) in some places.
This is misleading.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2297
Signed-off-by: Tejas Vipin <tejasvipin76@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
The machine calls serial_hds_isa_init() which is provided by serial-isa.c,
guarded by SERIAL_ISA.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240814181534.218964-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The ppc_hash64_hpt_base() and ppc_hash64_hpt_mask() functions are
mostly used by mmu-hash64.c only but there is one call to
ppc_hash64_hpt_mask() in hw/ppc/spapr_vhyp_mmu.c.in a helper function
that can be moved to mmu-hash64.c which allows these functions to be
removed from the header.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
SPI controller device model supports a connection to a single SPI responder.
This provide access to SPI seeproms, TPM, flash device and an ADC controller.
All SPI function control is mapped into the SPI register space to enable full
control by firmware. In this commit SPI configuration component is modelled
which contains all SPI configuration and status registers as well as the hold
registers for data to be sent or having been received.
An existing QEMU SSI framework is used and SSI_BUS is created.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
[np: Fix FDT macro compile for qtest]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Recent POWER CPUs can operate in "LPAR per core" or "LPAR per thread"
modes. In per-core mode, some SPRs and IPI doorbells are shared between
threads in a core. In per-thread mode, supervisor and user state is
not shared between threads.
OpenPOWER systems after POWER8 use LPAR per thread mode, and it is
required for KVM. Enterprise systems use LPAR per core mode, as they
partition the machine by core.
Implement a lpar-per-core machine option for powernv machines. This
is fixed true for POWER8 machines, and defaults off for P9 and P10.
With this change, powernv8 SMT now works sufficiently to run Linux,
with a single socket. Multi-threaded KVM guests still have problems,
as does multi-socket Linux boot.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The PC unit in the processor core contains xscom registers that provide
low level status and control of the CPU.
This implements "direct controls", sufficient for skiboot firmware,
which uses it to send NMI IPIs between CPUs.
POWER10 is sufficiently different from POWER9 (particularly with respect
to QME and special wakeup) that it is not trivial to implement POWER9
support by reusing the code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power CPUs have an execution control facility that can pause, resume,
and cause NMIs, among other things. Add a function that will nmi a CPU
and resume it if it was paused, in preparation for implementing the
control facility.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Big-core implementation is complete, so expose it as a machine
property that may be set with big-core=on option on powernv9 and
powernv10 machines.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
