Currently, QCA807x doesnt do any kind of validation to see whether it
actually supports the inserted module.
So lets add checks to allow only 1000BaseX and 100BaseFX based modules.
While adding validation, move fiber configuration to insert/remove events
instead of always doing it at config time.
This allows getting rid of the DT property for fiber enable and now only
the upstream sfp phandle is required.
Since we are refactoring fiber related code, lets heavily simplify the
status polling as the current logic is overcomplicated due to previous
wish to support non standard SFP cages that dont have pins properly
connected, that is removed now and only proper SFP cages will work.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In order to start working on IPQESS + DSA drop the old ESSEDMA + AR40xx
driver combo.
Remove the kernel symbols, disable swconfig and drop swconfig package
as they are not needed anymore.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
mac80211 incorrectly processes A-MSDUs contained in A-MPDU frames. This
results in dropped packets and severely impacted throughput.
As a workaround, don't indicate support for A-MSDUs contained in
A-MPDUs. This improves throughput over mesh links by factor 10.
Ref: https://github.com/openwrt/mt76/issues/450
Signed-off-by: David Bauer <mail@david-bauer.net>
If you would like to compile the newest version of U-boot together with the stable
OpenWrt version, which does not have LibreSSL >= 3.5, which was updated
in the master branch by commit 5451b03b7c
("tools/libressl: bump to v3.5.3"), then you need these two patches to
fix it. They are backported from U-boot repository.
This should be backported to stable OpenWrt versions.
Reported-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This issue was reported by @paper42, who is using Void Linux with musl
to compile OpenWrt and its packages and found out it is not possible to
compile U-boot for Turris Omnia (neither any other).
It fixes following output:
```
HOSTCC tools/kwboot
tools/kwboot.c: In function 'kwboot_tty_change_baudrate':
tools/kwboot.c:662:6: error: 'struct termios' has no member named 'c_ospeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:662:21: error: 'struct termios' has no member named 'c_ispeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:690:31: error: 'struct termios' has no member named 'c_ospeed'
690 | if (!_is_within_tolerance(tio.c_ospeed, baudrate, 3))
| ^
tools/kwboot.c:693:31: error: 'struct termios' has no member named 'c_ispeed'
693 | if (!_is_within_tolerance(tio.c_ispeed, baudrate, 3))
|
```
Tested-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Remove upstremed patch:
- 100-tracecmd-add-NO_LIBZSTD-option-to-disable-libzstd.patch
Changes:
c65c02c trace-cmd: Version 3.1.3
14a7aca trace-cmd library: Add API for mapping between host and guests
9191b8e tracecmd extract: Allow using --compression.
d63ae35 trace-cmd report: Add callback for kvm plugin to show guest functions
0c7ef72 trace-cmd library: Add man pages for iterator functions
3cd1b55 trace-cmd library: Add tracecmd_follow_event()
27ea9e1 libtracecmd: Add documentation on tracecmd_set/get_private()
3c544ad libtracecmd: Add a man pages for handling of time stamps
5baf7a3 libtracecmd: Add check-manpages.sh
ee007a1 trace-cmd library: Make tracecmd_filter_match() local
cb04105 tracecmd library documentation: Use star and not underscore for function names
54931be trace-cmd: Do not return zero length name for guest by name
43ffa27 trace-cmd: Close socket descriptor on failed connection
4744ca3 trace-cmd record/agent: Add --notimeout option
e512b22 trace-cmd: Add compile time overrides for libraries
a6fe935 trace-cmd: README: Add note on installing libtracecmd
067f45f trace-cmd: libtracecmd: Fixing linking to C++ code
689a0d4 tracecmd: Add NO_LIBZSTD option to disable libzstd
6bbcd3e trace-cmd report: Use library tracecmd_filter_*() logic
955d05f trace-cmd report: Make filter arguments match their files
82ed4a9 trace-cmd library: Add filtering logic for iterating events
dbd8777 trace-cmd report: Use tracecmd_iterate_events_multi()
78a74b1 trace-cmd library: Allow callers to save private data in tracecmd_input handlers
b37903a tracecmd library: Add tracecmd_iterate_events_multi()
d83b662 tracecmd utest: Add test to test using the libraries to read
2cb6cc2 tracecmd library: Add tracecmd_iterate_events()
762839a tracecmd: Use make variable instead of if statement for zlib test
1504f3f trace-cmd: Document new proxy args for {agent,record}
9a1c5d7 trace-cmd record: Keep --proxy from being passed to agents
ef8a8d7 trace-cmd libs: Initialize msg to NULL tracecmd_msg_read_data()
39ec10a trace-cmd: Do not use instance from trace context
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
93f4d52 libtracefs: version 1.5
bc857db libtracefs: Add tracefs_u{ret}probe_alloc to generic man page
db55441 libtracefs: Add tracefs_debug_dir() to generic libtracefs man page
d2d5924 libtracefs: Add test instructions for openSUSE
4a7b475 libtracefs: Fix test suite typo
ee8c644 libtracefs: Add tracefs_tracer_available() helper
799d88e libtracefs: Add API to set custom tracing directory
1bb00d1 libtracefs: allow pthread inclusion overrideable in Makefile
04651d0 libtracefs sqlhist: Allow pointers to match longs
9de59a0 libtracefs: Remove double free attempt of new_event in tracefs_synth_echo_cmd()
0aaa86a libtracefs: Fix use after free in tracefs_synth_alloc()
d2d5340 libtracefs: Add missed_events to record
9aaa8b0 libtracefs: Set the number of CPUs in tracefs_local_events_system()
56a0ba0 libtracefs: Return negative number when tracefs_filter_string_append() fails
c5f849f libtracefs: Set the long size of the tep handle in tracefs_local_events_system()
5c8103e revert: 0de961e74f96 ("libtracefs: Set visibility of parser symbols as 'internal'")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
fda4ad9 libtraceevent: version 1.6.3
d02a61e libtraceevent: Add man pages for tep_plugin_kvm_get/put_func()
6643bf9 libtraceevent: Have kvm_exit/enter be able to show guest function
a596299 libtraceevent: Add tep_print_field() to check-manpages.sh deprecated
065c9cd libtraceevent: Add man page documentation of tep_get_sub_buffer_size()
6e18ecc libtraceevent: Add man page for tep_plugin_add_option()
6738713 libtraceevent: Add some missing functions to generic libtraceevent man page
deefe29 libtraceevent: Include meta data functions in libtraceevent man pages
cf6dd2d libtraceevent: Add tep_get_function_count() to libtraceevent man page
5bfc11e libtraceevent: Add printk documentation to libtraceevent man page
65c767b libtraceevent: Update man page to reflect tep_is_pid_registered() rename
7cd173f libtraceevent: Add check-manpages.sh
fd6efc9 libtraceevent: Documentation: Correct typo in example
5c375b0 libtraceevent: Fixing linking to C++ code
7839fc2 libtraceevent: Makefile - set LIBS as conditional assignment
c5493e7 libtraceevent: Remove double assignment of val in eval_num_arg()
efd3289 libtraceevent: Add warnings if fields are outside the event
Signed-off-by: Nick Hainke <vincent@systemli.org>
4f96e67 Up the release version to 2.66
60ff008 Fix typos in the cap_from_text.3 man page.
281b6e4 Add captrace to .gitignore file
09a2c1d Add an example of using BPF kprobing to trace capability use.
26e3a09 Clean up getpcaps code.
fc804ac getpcaps: catch PID parsing errors.
fc437fd Fix an issue with bash displaying an error.
7db9589 Some more simplifications for building
27e801b Fix for "make clean ; make -j48 test"
Signed-off-by: Nick Hainke <vincent@systemli.org>
This patch is needed to handle interrupts by the second VPE on the Lantiq
ARX100, xRX200, xRX300 and xRX330 SoCs. Switching some ICU interrupts to
the second VPE results in a hang. Currently, the vsmp_init_secondary()
function is responsible for enabling these interrupts. It only enables
Malta-specific interrupts (SW0, SW1, HW4 and HW5).
The MIPS core has 8 interrupts defined. On Lantiq SoCs, hardware
interrupts are wired to an ICU instance. Each VPE has an independent
instance of the ICU. The mapping of the ICU interrupts is shown below:
SW0(IP0) - IPI call,
SW1(IP1) - IPI resched,
HW0(IP2) - ICU 0-31,
HW1(IP3) - ICU 32-63,
HW2(IP4) - ICU 64-95,
HW3(IP5) - ICU 96-127,
HW4(IP6) - ICU 128-159,
HW5(IP7) - timer.
This patch enables all interrupt lines on the second VPE.
This problem affects multithreaded SoCs with a custom interrupt controller.
SOCs with 1004Kc core and newer use the MIPS GIC. At this point, I am aware
that the Realtek RTL839x and RTL930x SoCs may need a similar fix. In the
future, this may be replaced with some generic solution.
Tested on Lantiq xRX200.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.
Fixes: #8577
Signed-off-by: Mark King <mark@vemek.co>
The workaround for an already-enabled R4K timer used a non-existent
macro CAUSE_DC. Fix compiling by using the actual macro CAUSEF_DC.
Fixes: b7aab19585 ("realtek: SMP handling of R4K timer interrupts")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Until now there has been no good explanation why we mess with the R4K
timer on SMP. After extensive testing and looking at the SDK code it
becomes clear what it is all about.
When we disable the CEVT_R4K module (we will do with the new timer
driver) the R4K timer hardware still fires interrupts on the secondary
CPU. To get around this we have two options:
- Disable IRQ 7
- Stop the counter completely
This patch selects option two because this is the root of evil.. To be
on the safe side we will do it only in case the CEVT_R4K module is
disabled.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The scope of the SMP startup structure is wrong. It is created on the
stack and not as a global variable. This can lead to startup failures.
Fixes: 3f41360eb7 ("realtek: use upstream recommendation for CPU start")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Use tools:latest container with prebuilt host tools to speedup kernel
compilation in kernel workflow.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add a simple script to make it easier to install a prebuilt tools tar.
Currently it will be used by our tools container and kernel workflow on
github.
Simple script that take a tar that contains prebuilt host tools, extract
them and refresh the timestamps to skip recompilation of such host
tools.
By default it refresh timestamps of build_dir/host and
staging_dir/host/stamp.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently each Kernel compilation takes about 30 minutes of which 20
minutes are used to compile our tools. While the toolchain is downloaded
and instantly ready the tools are missing.
This commit starts uploading a Docker container including compiled tools
which are ready to use. It is automatically updated whenever any tools
are changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Co-Developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add option to compile all host tools even if not needed.
This can be useful to prepare a universal precompiled host tools
archive to use in another buildroot and speedup compilation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
While experimenting with the AUTOREMOVE option in search of a way to use
prebuilt host tools in different buildroot, it was discovered that the
md5 generated by find_md5 in depends.mk is not reproducible.
Currently the hash is generated by the path of the file in addition to
the file mod time. Out of confusion, probably, there was an idea that
such command was used on the package build_dir. Reality is that this
command is run on the package files. (Makefile, patches, src)
This is problematic because the package Makefile (for example) change at
each git clone and base the hash on the Makefile mtime doesn't really
reflect if the Makefile actually changes across a buildroot or not.
A better approach is to generate an hash of each file and then generate
an hash on the sort hash list. This way we remove the problem of git
clone setting a wrong mtime while keeping the integrity of checking if a
file changed for the package as any change will result in a different
hash.
Introduce a new kind of find_md5 function, find_md5_reproducible that
apply this new logic and limit it only with AUTOREMOVE option set to
prevent any kind of slowdown due to additional hash generation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
cmake's find_package looks at host paths first for some reason. Switch
to using pkgconfig for the search, matching other modules.
Fixes: 3848cf458e ("tools/cmake: Build without some included libs")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Instead of using a fresh Linux installation which is setup every time
use the Buildbot container which is used for our own Buildbot
infrastructure, too.
While at it also tidy up the workflow to make it more consistent with
other workflow.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Co-Developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
As also ramips/mt7621 now has a user of the ubnt-ledbar driver, make
the package available on all targets by removing the dependency on
@TARGET_mediatek_mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches from mtk-openwrt-feeds (MTK SDK) to support reading
t-phy settings affecting PCIe as well as USB2 and USB3 from efuse.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
efuse is used to store board-specific settings of some of the in-SoC
peripherals. Add it to device tree, so it gets probed on boot and can
be accessed by other drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow byte-wise access to mtk-efuse as some drivers require that.
Patch imported from mtk-openwrt-feeds (MTK SDK).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The corresponding kmod package is marked as HIDDEN and selected by all
other kernel modules that need it, so the kconfig side will be in sync
without manual selection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
