meson is a next generation build system designed to have good defaults,
simpler build files, and fast compilation.
It is built upon python and uses ninja for compilation. The latter
provides fast by default (parallel) and problem free compilation.
There are over 40 packages already successfully using meson. The next
commit will convert pkgconf to use meson compilation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
ccaaab1c04 says that this is in the
codebase because of libsigc++, which is not in the codebase anymore.
Neither in base nor in packages. It doesn't seem to be needed by
anything else either. GNOME packages have transitioned to using meson,
which does not use m4 files.
Tested local compile with CONFIG_ALL. No problems seen.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Specifying serial in bootargs is not needed since the commit
ffeb37047e ("procd: update to git HEAD"). It's thanks to the procd
commit 2cfc26f8456a ("inittab: detect active console from kernel if no
console= specified").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
8a60e7e trace: don't leak file descriptor in error path
68df9ac procd: fix container deletion
f16abe0 uxc: add JSON output option for 'list' command
a23c888 jail: prepare for adding process to existing namespace
50da8a4 instance: allow jailed service to join namespace(s)
482d1ab Revert "jail: do not hack /etc/resolv.conf on container rootfs"
1eb4371 jail: start ubus and netifd instances for container with netns
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build cortexa7 subtarget with DSA driver for MDIO-connected Broadcom
BCM53xxx switches. This is needed for the Lamobo R1 aka. BananaPi
BPi-R1 board which comes with such a switch IC.
Remove old swconfig driver from target kernel config as the only board
using it is now supported by the DSA driver.
No changes to device tree are needed as upstream DTS already got a
DSA switch definition and we are just using that upstream source.
Update default network config of the Lamobo R1 to create lan bridge
with all 4 lan ports.
Introduce DEVICE_COMPAT_VERSION for the board to inform users about
having the re-create their network configuration and add device alias
as Bananapi BPi-R1 while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
bump version and remove patches that have been applied
176d701 wtmi: Wait 1s after putting PHYs INTn pin low
2eeccfe wtmi: Change comment describing reset workaround
e8c94a5 wtmi: Count RAM size from both CS0 and CS1
995979e wtmi: Rename macro
e29eb29 wtmi: soc: Fix start_ap_workaround() for TF-A with debug
81245ed wtmi: Use constant name PLAT_MARVELL_MAILBOX_BASE
18ccb83 wtmi: Do a proper UART reset with clock change as described in spec
15ff106 avs: Validate VDD value from OTP
3f33626 fix: clock: a3700: change pwm clock for 600/600 and 1200/750 preset
fb5e436 wtmi: uart: fix UART baudrate divisor calculation
Signed-off-by: sean lee <ilf@live.com>
Multiple profiles create artifacts, these should be stored in the JSON
file as well, allowing downstream tooling to show those files, too.
Artifacts don't have specific filesystems so only the fields `name`,
`type` and `sha256` are available.
Rename env variable names from IMAGE_ to FILE_ prefixes to reflect that
images, kernels and artifacts are added with the same command.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Summary of upstream CHANGELOG:
* Handle DHCPREBIND requests in the DHCPv6 server code.
* Fix bug which caused dnsmasq to lose track of processes forked.
* Major rewrite of the DNS server and domain handling code.
* Revise resource handling for number of concurrent DNS queries.
* Improve efficiency of DNSSEC.
* Connection track mark based DNS query filtering.
* Allow smaller than 64 prefix lengths in synth-domain.
* Make domains generated by --synth-domain appear in replies
when in authoritative mode.
* Ensure CAP_NET_ADMIN capability is available when
conntrack is configured.
* When --dhcp-hostsfile --dhcp-optsfile and --addn-hosts are
given a directory as argument, define the order in which
files within that directory are read.
* Support some wildcard matching of input tags to --tag-if.
Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
Starting with v3 of the vendor firmware for the TP-Link EAP235-Wall v1,
downgrades to firmware versions below v3 as not allowed. Since OpenWrt
uses version 0.0.0 as a default, this causes the factory install to fail
on devices with a recent firmware. This failure is associated by the
following message on the device's serial console:
EAP235/230-Wall forbid fw reverted from 3.x.x to lower version!
Vendor firmware (v3) also uses build and release numbers to compare
images, so identical version numbers are very unlikely to cause issues.
Bump the firmware version to 3.0.0 to ensure users can install OpenWrt
on their devices.
Reported-by: Colton Conor <colton.conor@gmail.com>
Tested-by: Colton Conor <colton.conor@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some devices using the safeloader firmware format require a minimum or
specific version to be set in the soft-version metadata partition.
Currently only custom text values can be provided, but not all device
firmware support this format.
Modify the device info struct to allow for more well-defined types of
soft-version overwrites, and provide a few macros for easy value
initialisation. Requires all existing values to be updated to match the
new structure.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[Adapt TL-WA1201-V2 entry too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes from 4.7.0:
Fix one high (OCSP verification issue) and two low vulnerabilities
Improve compatibility layer
Other improvements and fixes
For detailed changes refer to https://github.com/wolfSSL/wolfssl/releases
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Changes from 5.4 to 5.10:
-------------------------
- patches from 5.4 are all upstream for 5.10 execpt for
0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
- disable block device data integrity (DIF/DIX/T10) in default config
(CONFIG_BLK_DEV_INTEGRITY)
This feature is only supported by:
- Enterprise SAS/SCSI HBAs and Disks
- Software raid
- NVMEs with metadata capabilities (most don't have this)
None of which are part of any octeontx boards.
- arm64 TEXT_OFFSET (0x80000) has been removed after 5.4
This will break Uimages with kernel load addresses that aren't 2MiB
aligned any longer. Resulting in the kernel silently fail to boot.
For Gatworks newport boards for example, the uimage kernel load
and execute address is 0x20080000. These need to be changed to
0x20000000 when running kernels beyond 5.4.
Tested-on: Gateworks Newport GW64xx
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Linksyses Audi EA3500 and Viper E4200/E4500 have too small kernel
partition size when kernel 5.10 is used. This patch change kernel
partition to maximum size allowed by u-boot.
Kernel size is overlapping rootfs now, like mvebu Linksyses and stock
partition table. It fix back to stock via sysupgrade, which was broken
since 18.06.
Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
like commit 78c1ed6. Without this,Some USB port on H3 baseboard
can' work. So, need enable MUSB support on this target.
Signed-off-by: Zhao Yu <574249312@qq.com>
This patch fixes the forwarding behavior of bridge in bridge
configurations with DSA.
Without it, the configuration of the upper bridge might overwrite
settings of the lower bridge. For example, a vlan-aware bridge
with DSA interfaces in it might be offloaded to the DSA hardware. If the
bridge interface itself gets slave of a different bridge without vlan
filtering, the vlan filtering setting of the lower bridge is overwritten
by the upper bridge, which results in an incorrect hardware
configuration.
This was backported from kernel 5.7.
Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/
Fixes: FS#3996
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:
./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
These options are selectable when some of the kernel debug options like
KERNEL_SOFTLOCKUP_DETECTOR are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The LOCKUP_DETECTOR configuration option split into the
SOFTLOCKUP_DETECTOR and HARDLOCKUP_DETECTOR configuration option some
time ago. The HARDLOCKUP_DETECTOR option is only working on some
architectures, but SOFTLOCKUP_DETECTOR should work everywhere. Replace
KERNEL_LOCKUP_DETECTOR with KERNEL_SOFTLOCKUP_DETECTOR.
LOCKUP_DETECTOR will be selected by SOFTLOCKUP_DETECTOR automatically.
Fixes: b951f53fba ("build: Add additional kernel debug options")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move kernel version to 5.10 as has been tested by many users
with positive feedback.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[Tested on: ipq8064/g10; ipq8065/nbg6817]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ipq-wifi-netgear_wac510 package is not selected by any device and would
be empty anyway. The default board-2.bin from ath10k-board-qca4019 is
therefore used for this device and the package doesn't provide any visible
features.
Fixes: b126d9c3a3 ("ipq40xx: add netgear wac510 support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The structured soft-version partition has a field which contains a
(source) revision number. Factory images used to include this, but
it was accidentaly removed during an earlier refactoring.
Include the source revision number again in the generated soft-version
partition. Additionaly, also show this revision number when printing
image info.
Fixes: 1a211af2cb ("firmware-utils: tplink-safeloader: refactor meta-partition generation")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
1. Add support for Marvell CN9130 SoC
2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115
3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series
4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
When doing parallel build on a fast machine with bottleneck in i/o,
m_xt.so may start linking faster than dynsyms.list gets populated,
resulting in error:
ld:dynsyms.list:0: syntax error in dynamic list
Fix this by adding dynsyms.list as make dependency to m_xt.so
Described also here:
https://bugs.openwrt.org/index.php?do=details&task_id=3353
Change from v1:
- add dynsysms.list dependancy only when shared libs are enabled
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Fixes: FS#3353
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
It's been brewing on my cortexa9 subtarget (Turris Omnia) for months.
Perfectly stable.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
[modify subject to match previous updates]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This was missed because scancode license scanner was confused by a
slightly different than expected license text (96,75% license score).
License text included "file" instead of "library" in the main part of
the licensing info. It also used "The GNU C Library" instead of the
standard "This library" in 2nd and 3rd paragraphs.
The first paragraph clearly mentions LGPL-2.1-or-later and the use of
"file" instead of "library" should not affect licensing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
