Commit Graph

25288 Commits

Author SHA1 Message Date
Adrian Schmutzler
7b8eca902e tegra: switch to kernel 5.10
This target has testing support for kernel 5.10 for four months now.
Time to switch the default.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2021-10-18 21:32:36 +02:00
Rafał Miłecki
287257d676 bcm53xx: enable Linksys EA6300 & EA9200 builds
Both should be supported since:
1. Adding NVMEM driver for NVRAM
2. Using NVRAM info for determining active firmware partition

Linksys EA9500 uses very similar design and works fine.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-18 16:09:36 +02:00
Felix Fietkau
a1ac8728f8 ramips: remove kmod-mt7663-firmware-sta from device packages
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-17 16:07:03 +02:00
Rosen Penev
5b3d62247c ramips: fix dtc warnings for telco-electronics_x1
In all other dts files, the entire block is not edited like this.
They're edited separately.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-10-17 15:21:37 +02:00
Luis Araneda
88537e76ec zynq: switch to kernel 5.10
Use kernel 5.10 by default

compile-tested: all devices from target (wth ALL_KMODS)
run-tested: Digilent Zybo Z7-20

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
16ba7ca8be zynq: kernel: update config for 5.10
Update config with make kernel_oldconfig

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
861ff4d080 zynq: kernel: copy config from 5.4 to 5.10
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
97a427412a zynq: kernel: remove wireless extensions symbols
This fixes compilation of several wireless drivers that
require support for the old wireless extension to work.
One example is kmod-hermes.

The symbols are set to "y" on generic configuration.
But they were wrongly disabled on the target-specific
configuration.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
b898e869e2 zynq: kernel: refresh config
using "make kernel_oldconfig"

Several configs are now part of generic

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Daniel Golle
3a93704a63
mediatek: add EEPROM data for BPi-R64 2.4GHz wmac
EEPROM data extracted from vendor image found at
http://forum.banana-pi.org/t/bpi-r64-mt7622-mac80211-wifi-driver/10246/77
http://forum.banana-pi.org/uploads/short-url/jworbyBYpvrw9VQ2sx92B9z6DWS.bin

MAC address in the EEPROM has been zero'd which results in random
address on boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-15 00:12:30 +01:00
Felix Fietkau
f2e1e156c0 kernel: backport a rewrite of the mips eBPF JIT implementation
This adds support for eBPF JIT for 32 bit targets and significantly improves
correctness.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-14 20:29:51 +02:00
Paul Spooren
e07cc46991 x86/64: enable MMIO_CMDLINE_DEVICES for firecracker support
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.

Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.

Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-12 19:22:19 -10:00
Paul Spooren
4056a40160 armvirt: enable MMIO_CMDLINE_DEVICES for firecracker support
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.

Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.

Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-12 19:22:08 -10:00
Christian Lamparter
80b7a8a7f5 Revert "gpio-cdev: add nu801 userspace driver"
This reverts commit f536f5ebdd.

As Hauke commented, this causes builder failures on 5.4 kernels.
This revert includes changes to the mx100 kernel modules
dependency as well as the uci led definitions.

Tested-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 23:15:05 +02:00
Szabolcs Hubai
81d694e30b ipq40xx: use zImage for GL.iNet GL-B1300, GL-S1300 to shrink below 4096k
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.

While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage

Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.

The gzip compressed version would be 4116k.

[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-10-10 16:47:41 +02:00
Chris Blake
fe9e5fbd75 x86: add support for Meraki MX100
This commit will add support for the Meraki MX100 in OpenWRT.

Specs:
* CPU: Intel Xeon E3-1200 Series 1.5GHz 2C/4T
* Memory: 4GB DDR3 1600 ECC
* Storage: 1GB USB NAND, 1TB SATA HDD
* Wireless: None
* Wired: 10x 1Gb RJ45, 2x 1Gb SFP

UART:
The UART header is named CONN11 and is found in the
center of the mainboard. The pinout from Pin 1 (marked
with a black triangle) to pin 4 is below:
Pin 1: VCC
Pin 2: TX
Pin 3: RX
Pin 4: GND
Note that VCC is not required for UART on this device.

Booting:
1. Flash/burn one of the images from this repo to a
flash drive.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Hook up UART to the MX100, plug in the USB drive,
and then power up the device.
4. At the BIOS prompt, quickly press F7 and then
scroll to the Save & Exit tab.
5. Scroll down to Boot Override, and select the
UEFI entry for your jumpdrive.

Note: UEFI booting will fail if the SATA cable for
the HDD is plugged in.
The issue is explained under the Flashing instructions.

Flashing:
1. Ensure the MX100 is powered down, and not plugged
into power.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Using the Mini USB female port found by the SATA
port on the motherboard,
flash one of the images to the system. Example:
`dd if=image of=/dev/sdb conv=fdatasync` where sdb
is the USB device for the MX100's NAND.
4. Unplug the Mini USB, hook up UART to the MX100,
and then power up the device.
5. At the BIOS prompt, quickly press F7 and then
scroll to the Boot tab.
6. Change the boot order and set UEFI: USB DISK 2.0
as first, and USB DISK 2.0 as second.
Disable the other boot options.
7. Go to Save & Exit, and then select Save Changes and
Reset

Note that OpenWRT will fail to boot in UEFI mode when
the SATA hard drive is plugged in. To fix this, boot
with the SATA disk unplugged and then run the following
command:
`sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg`
Once the above is ran, OpenWRT will boot when the HDD
is plugged into SATA. The reason this happens is the
UEFI implementation for the MX100 will always set
anything on SATA to HD0 instead of the onboard USB
storage, so we have to accomidate it since OpenWRT's
GRUB does not support detecting a boot disk via UUID.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2021-10-10 16:47:41 +02:00
Christian Lamparter
e166ee4ff1 apm821xx: disable and move kernel CONFIG_ symbols
try to reduce the kernel size by disabling and moving
options from the common kernel configuration to the
SATA target that doesn't have the constraints.

For NAND this has become necessary because as with 5.10
some devices outgrew their kernels. Though, in my tests
this didn't help much: just a smidgen over 100kib was
saved on the  uncompressed kernel.

... running make kernel_oldconfig also removed some
other config symbols, mostly those that already set
from elsewhere or became obsolete in the meantime.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:47:41 +02:00
Christian Lamparter
44f89614c6 apm821xx: disable MX60(W) due to kernel size
disables the MX60(W) from being built by the builders for now.
But there's an effort to bring it back:
<https://github.com/openwrt/openwrt/pull/4617>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:47:03 +02:00
Linus Walleij
4293fc32b7 gemini: splash banner on framebuffer console
The D-Link DIR-685 has a small screen with a framebuffer
console, so if we have this, when we start, display the
banner on this framebuffer console so the user know they
are running OpenWRT as root filesystem.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-10-10 16:44:15 +02:00
Christian Lamparter
7a6a349445 apm821xx: WNDAP620 + WNDAP660: reorganize partitions for 5.10
Due to 5.10 increased kernel size, the current 4MiB-ish kernel
partition got too small. Luckily, netgear's uboot environment
is setup to read 0x60000 bytes from the kernel partition location.

... While at it: also do some cleanups in the DTS in there.

The original (re-)installation described in
commit d82d84694e ("apm821xx: add support for the Netgear WNDAP620 and WNDAP660")
seemed to be still working for now. What I noticed though
is that the bigger initramfs images needed to use a different
destination address (1000000) to prevent it overwriting
itself during decompression. i.e:
 # tftp 1000000 openwrt-...-wndap620-initramfs-kernel.bin
 # bootm

However, in case of the WNDAP620+660 the factory.img image can be
written directly to the flash through uboot.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:44:15 +02:00
Paul Spooren
4ee9b3f462 apm821xx: switch to Kernel 5.10
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-10 16:44:15 +02:00
Christian Lamparter
2a6cab09b9 apm821xx: move CONFIG_DMA* to the generic apm821xx config
Both NAND and SATA targets need the DMA engine in one way
or another.

Due to a kernel config refresh various existing symbols
got removed from the apm821xx main config file as well.
(That being said, they are still included because the
built-in crpyto4xx depends on these.)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:44:15 +02:00
John Audia
b5893a4128 kernel: bump 5.4 to 5.4.152
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:12:55 +01:00
John Audia
416eef7209 kernel: bump 5.4 to 5.4.151
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:12:10 +01:00
John Audia
e672d1b387 kernel: bump 5.10 to 5.10.72
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:09:22 +01:00
John Audia
20bc450771 kernel: bump 5.10 to 5.10.71
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:09:22 +01:00
Adrian Schmutzler
91eed5d9fb rockchip: rename "Rock Pi 4" to "Rock Pi 4A"
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.

For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-10 00:57:56 +02:00
Adrian Schmutzler
0c2aa7c003 rockchip: switch to kernel 5.10
This target has testing support for more than half a year now.
Time to switch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-10 00:51:39 +02:00
Ansuel Smith
5ae2e78639 kernel: drop support for mtd-mac-address
Now that we have fully switched to nvmem interface we can drop
the use of mtd-mac-address patches as it's not used anymore and
the new nvmem implementation should be used for any new device.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-10-09 21:14:54 +02:00
Robert Marko
46646efc38 mvebu: mochabin: correct LED labels in DTS
LED labels got reversed by accident, so fix it to the usual color:led_name format.

Fixes: 78cf3e53b1 ("mvebu: add Globalscale MOCHAbin")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-09 19:27:11 +02:00
Adrian Schmutzler
fb76d543b6 kirkwood: switch to kernel 5.10
This target has testing support for more than half a year now.
Time to switch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-09 18:44:55 +02:00
Daniel Golle
7ab94288e0
oxnas: switch to Linux 5.10
Linux 5.10 has been there as testing kernel for a while now.
Do the switch and drop config and patches for Linux 5.4.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-09 16:48:45 +01:00
Daniel Golle
401d7ebf2c
mediatek: enable configfs for DT overlay on mt7622 and mt7623
Enable kernel options to allow loading device tree overlay via configfs
at runtime. This is useful for devboards like the BPi-R2 and BPi-R64
which got RasbPi-compatible 40-pin GPIO header which allow all sorts
of extensions.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-09 16:48:34 +01:00
Birger Koblitz
cda0460ad3 realtek: add legacy realtek GPIO driver for rtl9300 support
The otto GPIO driver does not work with rtl9300 SoCs. Add
the legacy driver again and use that by default in the 9300 .dtsi

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
4c83dae801 realtek: enable Aquantia PHY support
Enables Aquantia PHY support in the kernel

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
76f60470a1 realtek: Fix bug when accessing external PHYs on SoCs older than Revision C
RTL8393 SoCs older than Revision C hang on accesses to PHYs with PHY address
larger or equal to the CPU-port (52). This will make scanning the MDIO bus
hang forever. Since the RTL8390 platform does not support more than
52 PHYs, return -EIO for phy addresses >= 52. Note that the RTL8390 family
of SoCs has a fixed mapping between port number and PHY-address.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
88936e7e82 realtek: cleanup PHY driver
Removes unnecessary output from the RTL PHY drivers.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
1cfd45ae0b realtek: Add debugfs support for RTL9300
Adds support for debugfs on RTL9300, in particular the drop counters.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
1f402512ae realtek: Add SoC-specific routing offload implementation
Adds SoC specific routing offload implementations for
RTL8380/90 and RTL9300. RTL83xx supports merely nexthop
routing, RTL9300 full host and prefix routes.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
03e1d93e07 realtek: add driver support for routing offload
Add generic support for listening to FIB and Event notifier updates and
use this information to hook into the L3 hardware capabilities of the
RTL SoCs.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
35b3c4c212 kernel: Add AQR113C and AQR813 support
This hack adds support for the Aquantia 4th generation, 10GBit
PHYs AQR113C and AQR813.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
ee6f483a62 realtek: Improve MDIO bus probing for RTL9300
Improve handling of multi-gig ports on the RTL9300 when probing
the MDIO bus.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
9ae927febd realtek: Fix bug in VLAN ingress and egress filtering
The ingress filter registers use 2 bits for each port to define the filtering
state, whereas the egress filter uses 1 bit. So for for the ingress filter
the register offset for a given port is:
(port >> 4) << 4: since there are 16 entries in a register of 32 bits
and for the egress filter:
(port >> 5) << 4: since there are 32 entries in a register of 32 bits

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
28e972b2ea realtek: Configure initial L2 learning setup
Configure a sane L2 learning configuration upon DSA driver load so that the
switch can start learning L2 addresses. Also configure the correct flood masks
for broadcast and unknown unicast traffice.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
9d9bf16aa8 realtek: Add phylink configuration routines for RTL93xx
This adds RTL93xx-specific MAC configuration routines that allow also configuration
of 10GBit links for phylink. There is support for the Realtek-specific HISGMI
protocol.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
a96b73a890 realtek: Packet Inspection Engine support for RTL930x SoCs
Adds the RTL930x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
2d8d81fe28 realtek: Packet Inspection Engine support for RTL839x SoCs
Adds the RTL839x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
87b3bd07a4 realtek: Packet Inspection Engine support for RTL838x SoCs
Adds the RTL838x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
54805fc911 realtek: Add driver support for TC offloading
This adds support for offloading TC flower by using the Packet Inspection Engine
of the RTL-SoCs. Basic infrastructure support is provide with callbacks to the
tc subsystem and support for HW packet counters.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
a6678accbd realtek: Add port to smi-bus address mapping
All RTL SoCs addresss PHYs via their port number, which is mapped to an
SMI address. Add support for configuring this mapping via the .dts on all
SoCs apart from the 839x, where the mapping to the 64 ports is fixed.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00