mirror of
https://github.com/openwrt/openwrt.git
synced 2024-11-29 21:06:33 +08:00
ath79: add support for TP-Link RE350K v1
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit is contained in:
Piotr Dymacz
parent
82dbcd8bf2
commit
db91418766
@ -18,6 +18,7 @@ ath79_setup_interfaces()
|
||||
pcs,cap324|\
|
||||
pisen,wmm003n|\
|
||||
pqi,air-pen|\
|
||||
tplink,re350k-v1|\
|
||||
tplink,re450-v2|\
|
||||
tplink,tl-mr10u|\
|
||||
tplink,tl-mr3020-v1|\
|
||||
|
||||
@ -141,6 +141,10 @@ case "$FIRMWARE" in
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
||||
;;
|
||||
tplink,re350k-v1)
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +2)
|
||||
;;
|
||||
ubnt,unifiac-lite|\
|
||||
ubnt,unifiac-mesh|\
|
||||
ubnt,unifiac-mesh-pro|\
|
||||
|
||||
173
target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts
Normal file
173
target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts
Normal file
@ -0,0 +1,173 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca9557.dtsi"
|
||||
|
||||
/ {
|
||||
model = "TP-Link RE350K v1";
|
||||
compatible = "tplink,re350k-v1", "qca,qca9558";
|
||||
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &power;
|
||||
led-running = &power;
|
||||
led-upgrade = &power;
|
||||
mdio-gpio0 = &mdio2;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
app-config {
|
||||
label = "app-config";
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
led {
|
||||
label = "led";
|
||||
linux,code = <BTN_1>;
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power: power {
|
||||
label = "tp-link:green:power";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan2g-green {
|
||||
label = "tp-link:green:wlan2g";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan2g-red {
|
||||
label = "tp-link:red:wlan2g";
|
||||
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan5g-green {
|
||||
label = "tp-link:green:wlan5g";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan5g-red {
|
||||
label = "tp-link:red:wlan5g";
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio2: mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio 18 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
phy0: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
|
||||
phy-mode = "rgmii-rxid";
|
||||
at803x-disable-smarteee;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
pll-data = <0x9e000000 0x80000101 0x80001313>;
|
||||
phy-handle = <&phy0>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
|
||||
rxdv-delay = <2>;
|
||||
rxd-delay = <2>;
|
||||
txen-delay = <0>;
|
||||
txd-delay = <0>;
|
||||
rgmii-enabled = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "tplink,firmware";
|
||||
label = "firmware";
|
||||
reg = <0x020000 0xd70000>;
|
||||
};
|
||||
|
||||
config: partition@d90000 {
|
||||
label = "config";
|
||||
reg = <0xd90000 0x260000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
};
|
||||
@ -109,6 +109,22 @@ define Device/tplink_archer-c7-v5
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c7-v5
|
||||
|
||||
define Device/tplink_re350k-v1
|
||||
$(Device/tplink)
|
||||
ATH_SOC := qca9558
|
||||
IMAGE_SIZE := 13760k
|
||||
DEVICE_TITLE := TP-Link RE350K v1
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
||||
TPLINK_BOARD_ID := RE350K-V1
|
||||
TPLINK_HWID := 0x0
|
||||
TPLINK_HWREV := 0
|
||||
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header -O
|
||||
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \
|
||||
check-size $$$$(IMAGE_SIZE) | append-metadata
|
||||
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
||||
endef
|
||||
TARGET_DEVICES += tplink_re350k-v1
|
||||
|
||||
define Device/tplink_re450-v2
|
||||
$(Device/tplink)
|
||||
ATH_SOC := qca9563
|
||||
|
||||
@ -1144,6 +1144,38 @@ static struct device_info boards[] = {
|
||||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the RE350K v1 */
|
||||
{
|
||||
.id = "RE350K-V1",
|
||||
.vendor = "",
|
||||
.support_list =
|
||||
"SupportList:\n"
|
||||
"{product_name:RE350K,product_ver:1.0.0,special_id:00000000,product_region:US}\n",
|
||||
.support_trail = '\x00',
|
||||
.soft_ver = NULL,
|
||||
|
||||
/** We're using a dynamic kernel/rootfs split here */
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"firmware", 0x20000, 0xd70000},
|
||||
{"partition-table", 0xd90000, 0x02000},
|
||||
{"default-mac", 0xda0000, 0x00020},
|
||||
{"pin", 0xda0100, 0x00020},
|
||||
{"product-info", 0xda1100, 0x01000},
|
||||
{"soft-version", 0xdb0000, 0x01000},
|
||||
{"support-list", 0xdb1000, 0x01000},
|
||||
{"profile", 0xdb2000, 0x08000},
|
||||
{"user-config", 0xdc0000, 0x10000},
|
||||
{"default-config", 0xdd0000, 0x10000},
|
||||
{"device-id", 0xde0000, 0x00108},
|
||||
{"radio", 0xff0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the RE355 */
|
||||
{
|
||||
.id = "RE355",
|
||||
|
||||
Loading…
Reference in New Issue
Block a user