mirror of
https://github.com/openwrt/openwrt.git
synced 2024-11-27 03:43:37 +08:00
kirkwood: add support for ipTIME NAS1
ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC. Specifications: * SoC: 88F6281 * RAM: 256 MiB * Flash: SPI NOR 16 MiB * SATA: 1x 3Gb/s * Ethernet: 1x 1GbE * USB: 1x 2.0 * Fan: 2 speed level * UART: JP1 (115200 8N1) * Pinout: [3V3] (TXD) (RXD) (GND) Notes: * There are several variants of the model name: "NAS-I", "NASI", "NAS1". Here "NAS1" is adopted for consistent naming scheme. * The reset button is also a USB copy button in stock FW, but in this patch the former is the only default behavior. Installation via web interface: 1. Flash sysupgrade image through the stock web interface. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit is contained in:
Sungbo Eo
parent
0c568d044f
commit
957f9adeb1
@ -295,6 +295,11 @@ define Build/install-dtb
|
||||
)
|
||||
endef
|
||||
|
||||
define Build/iptime-naspkg
|
||||
$(STAGING_DIR_HOST)/bin/iptime-naspkg $(1) $@ $@.new
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/jffs2
|
||||
rm -rf $(KDIR_TMP)/$(DEVICE_NAME)/jffs2 && \
|
||||
mkdir -p $(KDIR_TMP)/$(DEVICE_NAME)/jffs2/$$(dirname $(1)) && \
|
||||
|
||||
@ -22,6 +22,7 @@ kirkwood_setup_interfaces()
|
||||
globalscale,sheevaplug|\
|
||||
iom,iconnect-1.1|\
|
||||
iom,ix2-200|\
|
||||
iptime,nas1|\
|
||||
netgear,readynas-duo-v2|\
|
||||
raidsonic,ib-nas62x0|\
|
||||
seagate,blackarmor-nas220|\
|
||||
@ -55,6 +56,10 @@ kirkwood_setup_macs()
|
||||
local label_mac=""
|
||||
|
||||
case "$board" in
|
||||
iptime,nas1)
|
||||
lan_mac=$(mtd_get_mac_binary u-boot 0x3ffa8)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
linksys,e4200-v2|\
|
||||
linksys,ea3500|\
|
||||
linksys,ea4500)
|
||||
|
||||
@ -27,6 +27,10 @@ preinit_set_mac_address() {
|
||||
ip link set dev port3 address $(macaddr_add $mac 2) 2>/dev/null
|
||||
ip link set dev port4 address $(macaddr_add $mac 3) 2>/dev/null
|
||||
;;
|
||||
iptime,nas1)
|
||||
mac=$(mtd_get_mac_binary u-boot 0x3ffa8)
|
||||
ip link set dev eth0 address $mac 2>/dev/null
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
|
||||
@ -1,6 +1,7 @@
|
||||
RAMFS_COPY_BIN='fw_printenv fw_setenv strings'
|
||||
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||
|
||||
PART_NAME=firmware
|
||||
REQUIRE_IMAGE_METADATA=1
|
||||
|
||||
platform_check_image() {
|
||||
@ -33,6 +34,9 @@ platform_do_upgrade() {
|
||||
return 1
|
||||
fi
|
||||
;;
|
||||
iptime,nas1)
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
linksys,e4200-v2|\
|
||||
linksys,ea3500|\
|
||||
linksys,ea4500)
|
||||
|
||||
@ -122,6 +122,7 @@ CONFIG_HARDIRQS_SW_RESEND=y
|
||||
CONFIG_HAS_DMA=y
|
||||
CONFIG_HAS_IOMEM=y
|
||||
CONFIG_HAS_IOPORT_MAP=y
|
||||
CONFIG_HWMON=y
|
||||
CONFIG_HW_RANDOM=y
|
||||
CONFIG_HW_RANDOM_OMAP=y
|
||||
CONFIG_HZ_FIXED=0
|
||||
@ -163,6 +164,9 @@ CONFIG_MTD_NAND_ECC_SW_HAMMING=y
|
||||
# CONFIG_MTD_NAND_MARVELL is not set
|
||||
CONFIG_MTD_NAND_ORION=y
|
||||
CONFIG_MTD_RAW_NAND=y
|
||||
CONFIG_MTD_SPI_NOR=y
|
||||
CONFIG_MTD_SPLIT_FIRMWARE=y
|
||||
CONFIG_MTD_SPLIT_UIMAGE_FW=y
|
||||
CONFIG_MTD_UBI=y
|
||||
CONFIG_MTD_UBI_BEB_LIMIT=20
|
||||
CONFIG_MTD_UBI_BLOCK=y
|
||||
@ -248,6 +252,7 @@ CONFIG_SPARSE_IRQ=y
|
||||
CONFIG_SPI=y
|
||||
# CONFIG_SPI_ARMADA_3700 is not set
|
||||
CONFIG_SPI_MASTER=y
|
||||
CONFIG_SPI_MEM=y
|
||||
CONFIG_SPI_ORION=y
|
||||
CONFIG_SPLIT_PTLOCK_CPUS=999999
|
||||
CONFIG_SRAM=y
|
||||
@ -259,6 +264,7 @@ CONFIG_THERMAL=y
|
||||
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
|
||||
CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
|
||||
CONFIG_THERMAL_GOV_STEP_WISE=y
|
||||
CONFIG_THERMAL_HWMON=y
|
||||
CONFIG_THERMAL_OF=y
|
||||
CONFIG_TICK_CPU_ACCOUNTING=y
|
||||
CONFIG_TIMER_OF=y
|
||||
|
||||
231
target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-nas1.dts
Normal file
231
target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-nas1.dts
Normal file
@ -0,0 +1,231 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "kirkwood.dtsi"
|
||||
#include "kirkwood-6281.dtsi"
|
||||
|
||||
/ {
|
||||
model = "ipTIME NAS1";
|
||||
compatible = "iptime,nas1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_ready;
|
||||
led-failsafe = &led_ready;
|
||||
led-running = &led_ready;
|
||||
led-upgrade = &led_ready;
|
||||
};
|
||||
|
||||
chosen {
|
||||
/*
|
||||
* "root" argument from the stock bootloader should be ignored
|
||||
* as it'll prevent the kernel from finding the correct rootfs.
|
||||
*/
|
||||
bootargs-append = " console=ttyS0,115200 root=";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x00000000 0x10000000>;
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
pinctrl-0 = <&pmx_led>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
hdd {
|
||||
label = "blue:hdd";
|
||||
gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "ata1";
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "blue:usb";
|
||||
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ehci_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
led_ready: ready {
|
||||
label = "blue:ready";
|
||||
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
pinctrl-0 = <&pmx_button>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset-copy {
|
||||
label = "Reset/Copy Button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power {
|
||||
label = "Power Button";
|
||||
linux,code = <KEY_POWER>;
|
||||
gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-fan {
|
||||
compatible = "gpio-fan";
|
||||
|
||||
pinctrl-0 = <&pmx_fan>;
|
||||
pinctrl-names = "default";
|
||||
gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio1 10 GPIO_ACTIVE_HIGH>;
|
||||
/* We don't know the exact rpm, just use dummy values here. */
|
||||
gpio-fan,speed-map = <0 0>, <1 1>, <2 2>;
|
||||
#cooling-cells = <2>;
|
||||
};
|
||||
|
||||
gpio-poweroff {
|
||||
compatible = "gpio-poweroff";
|
||||
gpios = <&pca9536 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
regulators {
|
||||
compatible = "simple-bus";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
pinctrl-0 = <&pmx_usb_vbus>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
regulator@1 {
|
||||
compatible = "regulator-fixed";
|
||||
reg = <1>;
|
||||
regulator-name = "USB Power";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
pmx_led: pmx-led {
|
||||
marvell,pins = "mpp35", "mpp45", "mpp46";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_fan: pmx-fan {
|
||||
marvell,pins = "mpp41", "mpp42";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_usb_vbus: pmx-usb-vbus {
|
||||
marvell,pins = "mpp43";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_button: pmx-button {
|
||||
marvell,pins = "mpp44", "mpp48";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <20000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
compatible = "openwrt,uimage", "denx,uimage";
|
||||
openwrt,offset = <0x400>;
|
||||
label = "firmware";
|
||||
reg = <0x40000 0xf80000>;
|
||||
};
|
||||
|
||||
partition@fc0000 {
|
||||
label = "config";
|
||||
reg = <0xfc0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&rtc {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
|
||||
pca9536: gpio@41 {
|
||||
compatible = "nxp,pca9536";
|
||||
reg = <0x41>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ehci_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
ethphyb: ethernet-phy@b {
|
||||
reg = <0x0b>;
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð1port {
|
||||
phy-handle = <ðphyb>;
|
||||
phy-connection-type = "rgmii-id";
|
||||
};
|
||||
|
||||
&sata {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
nr-ports = <1>;
|
||||
|
||||
sata-port@0 {
|
||||
reg = <0>;
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
};
|
||||
@ -184,6 +184,21 @@ define Device/iom_ix2-200
|
||||
endef
|
||||
TARGET_DEVICES += iom_ix2-200
|
||||
|
||||
define Device/iptime_nas1
|
||||
DEVICE_VENDOR := ipTIME
|
||||
DEVICE_MODEL := NAS1
|
||||
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
|
||||
kmod-gpio-button-hotplug kmod-gpio-pca953x kmod-hwmon-drivetemp \
|
||||
kmod-hwmon-gpiofan kmod-usb-ledtrig-usbport -uboot-envtools
|
||||
KERNEL := $$(KERNEL) | iptime-naspkg nas1
|
||||
BLOCKSIZE := 256k
|
||||
IMAGE_SIZE := 15872k
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
||||
check-size | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += iptime_nas1
|
||||
|
||||
define Device/linksys
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_PACKAGES := kmod-mwl8k wpad-basic-wolfssl kmod-gpio-button-hotplug
|
||||
|
||||
Loading…
Reference in New Issue
Block a user