mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-14 20:34:10 +08:00
ipq40xx: add support for EnGenius EMD1
SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (1 port) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMD1. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [removed BOARD_NAME] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit is contained in:
Yen-Ting-Shen
Christian Lamparter
parent
52b8c7a892
commit
51f3035978
@ -28,6 +28,7 @@ ALLWIFIBOARDS:= \
|
||||
aruba_ap-303 \
|
||||
avm_fritzrepeater-1200 \
|
||||
dlink_dap2610 \
|
||||
engenius_emd1 \
|
||||
ezviz_cs-w3-wd1200g-eup \
|
||||
linksys_ea8300 \
|
||||
qxwlan_e2600ac
|
||||
@ -96,6 +97,7 @@ endef
|
||||
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
|
||||
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
|
||||
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
|
||||
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
|
||||
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
||||
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
|
||||
|
||||
BIN
package/firmware/ipq-wifi/board-engenius_emd1.qca4019
Normal file
BIN
package/firmware/ipq-wifi/board-engenius_emd1.qca4019
Normal file
Binary file not shown.
@ -49,6 +49,7 @@ ipq40xx_setup_interfaces()
|
||||
avm,fritzrepeater-1200|\
|
||||
dlink,dap-2610 |\
|
||||
engenius,eap1300|\
|
||||
engenius,emd1|\
|
||||
meraki,mr33|\
|
||||
netgear,ex6100v2|\
|
||||
netgear,ex6150v2|\
|
||||
@ -108,6 +109,10 @@ ipq40xx_setup_macs()
|
||||
lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
engenius,emd1)
|
||||
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
engenius,ens620ext)
|
||||
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
lan_mac=$(macaddr_add "$wan_mac" 1)
|
||||
|
||||
@ -91,6 +91,10 @@ case "$FIRMWARE" in
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
|
||||
;;
|
||||
engenius,emd1)
|
||||
caldata_extract "0:ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr)
|
||||
;;
|
||||
engenius,ens620ext)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
|
||||
@ -166,6 +170,10 @@ case "$FIRMWARE" in
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
|
||||
;;
|
||||
engenius,emd1)
|
||||
caldata_extract "0:ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1)
|
||||
;;
|
||||
engenius,ens620ext)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)
|
||||
|
||||
@ -0,0 +1,233 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "EnGenius EMD1";
|
||||
compatible = "engenius,emd1";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
switch_lan_bmp = <0x20>;
|
||||
switch_wan_bmp = <0x00>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
qcom,num_gmac = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "emd1:white:power";
|
||||
gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "emd1:red:wlan2g";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "emd1:blue:wlan5g";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
mesh {
|
||||
label = "emd1:orange:mesh";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio54", "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition0@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
partition1@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
partition2@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
partition3@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition4@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition5@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition6@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
partition7@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition8@180000 {
|
||||
label = "userconfig";
|
||||
reg = <0x00180000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
partition9@200000 {
|
||||
compatible = "denx,fit";
|
||||
label = "firmware";
|
||||
reg = <0x200000 0x01e00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <1 0x20>;
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "EnGenius-EMD1";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "EnGenius-EMD1";
|
||||
};
|
||||
@ -278,6 +278,19 @@ define Device/engenius_eap1300
|
||||
endef
|
||||
TARGET_DEVICES += engenius_eap1300
|
||||
|
||||
define Device/engenius_emd1
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EMD1
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
SOC := qcom-ipq4018
|
||||
IMAGE_SIZE := 30720k
|
||||
IMAGES := sysupgrade.bin factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE)
|
||||
endef
|
||||
TARGET_DEVICES += engenius_emd1
|
||||
|
||||
define Device/engenius_ens620ext
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -785,11 +785,41 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -20,6 +20,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
|
||||
+ qcom-ipq4018-ea6350v3.dtb \
|
||||
+ qcom-ipq4018-eap1300.dtb \
|
||||
+ qcom-ipq4018-emd1.dtb \
|
||||
+ qcom-ipq4018-ens620ext.dtb \
|
||||
+ qcom-ipq4018-ex6100v2.dtb \
|
||||
+ qcom-ipq4018-ex6150v2.dtb \
|
||||
|
||||
Loading…
Reference in New Issue
Block a user