We add ssl_cipher_get_overhead() as an internal function, to avoid
having too much ciphersuite-specific knowledge in DTLS_get_data_mtu()
itself. It's going to need adjustment for TLSv1.3... but then again, so
is fairly much *all* of the SSL_CIPHER handling. This bit is in the noise.
Reviewed-by: Rich Salz <rsalz@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
ssl_set_handshake_header2() was only ever a temporary name while we had
to have ssl_set_handshake_header() for code that hadn't been converted to
WPACKET yet. No code remains that needed that so we can rename it.
Reviewed-by: Rich Salz <rsalz@openssl.org>
Remove the old ssl_set_handshake_header() implementations. Later we will
rename ssl_set_handshake_header2() to ssl_set_handshake_header().
Reviewed-by: Rich Salz <rsalz@openssl.org>
We actually construct a HelloVerifyRequest in two places with common code
pulled into a single function. This one commit handles both places.
Reviewed-by: Rich Salz <rsalz@openssl.org>
DTLS can handle out of order record delivery. Additionally since
handshake messages can be bigger than will fit into a single packet, the
messages can be fragmented across multiple records (as with normal TLS).
That means that the messages can arrive mixed up, and we have to
reassemble them. We keep a queue of buffered messages that are "from the
future", i.e. messages we're not ready to deal with yet but have arrived
early. The messages held there may not be full yet - they could be one
or more fragments that are still in the process of being reassembled.
The code assumes that we will eventually complete the reassembly and
when that occurs the complete message is removed from the queue at the
point that we need to use it.
However, DTLS is also tolerant of packet loss. To get around that DTLS
messages can be retransmitted. If we receive a full (non-fragmented)
message from the peer after previously having received a fragment of
that message, then we ignore the message in the queue and just use the
non-fragmented version. At that point the queued message will never get
removed.
Additionally the peer could send "future" messages that we never get to
in order to complete the handshake. Each message has a sequence number
(starting from 0). We will accept a message fragment for the current
message sequence number, or for any sequence up to 10 into the future.
However if the Finished message has a sequence number of 2, anything
greater than that in the queue is just left there.
So, in those two ways we can end up with "orphaned" data in the queue
that will never get removed - except when the connection is closed. At
that point all the queues are flushed.
An attacker could seek to exploit this by filling up the queues with
lots of large messages that are never going to be used in order to
attempt a DoS by memory exhaustion.
I will assume that we are only concerned with servers here. It does not
seem reasonable to be concerned about a memory exhaustion attack on a
client. They are unlikely to process enough connections for this to be
an issue.
A "long" handshake with many messages might be 5 messages long (in the
incoming direction), e.g. ClientHello, Certificate, ClientKeyExchange,
CertificateVerify, Finished. So this would be message sequence numbers 0
to 4. Additionally we can buffer up to 10 messages in the future.
Therefore the maximum number of messages that an attacker could send
that could get orphaned would typically be 15.
The maximum size that a DTLS message is allowed to be is defined by
max_cert_list, which by default is 100k. Therefore the maximum amount of
"orphaned" memory per connection is 1500k.
Message sequence numbers get reset after the Finished message, so
renegotiation will not extend the maximum number of messages that can be
orphaned per connection.
As noted above, the queues do get cleared when the connection is closed.
Therefore in order to mount an effective attack, an attacker would have
to open many simultaneous connections.
Issue reported by Quan Luo.
CVE-2016-2179
Reviewed-by: Richard Levitte <levitte@openssl.org>
Run util/openssl-format-source on ssl/
Some comments and hand-formatted tables were fixed up
manually by disabling auto-formatting.
Reviewed-by: Rich Salz <rsalz@openssl.org>
DTLSv1_client_method() is deprecated, but it was the only way to obtain
DTLS1_BAD_VER support. The SSL_OP_CISCO_ANYCONNECT hack doesn't work with
DTLS_client_method(), and it's relatively non-trivial to make it work without
expanding the hack into lots of places.
So deprecate SSL_OP_CISCO_ANYCONNECT with DTLSv1_client_method(), and make
it work with SSL_CTX_set_{min,max}_proto_version(DTLS1_BAD_VER) instead.
Reviewed-by: Rich Salz <rsalz@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
Fix some indentation at the same time
Reviewed-by: Matt Caswell <matt@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/1292)
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/1264)
Based on an orignal commit by GitHub user BertramScharpf. Rebased and
updated to take account of all the updates since this was first raised.
GH PR#62
Reviewed-by: Rich Salz <rsalz@openssl.org>
To enable heartbeats for DTLS, configure with enable-heartbeats.
Heartbeats for TLS have been completely removed.
This addresses RT 3647
Reviewed-by: Richard Levitte <levitte@openssl.org>
Adds a set of tests for the newly rewritten DTLSv1_listen function.
The test pokes various packets at the function and then checks
the return value and the data written out to ensure it is what we
would have expected.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
The recently rewriten DTLSv1_listen code does not support fragmented
ClientHello messages because fragment reassembly requires server state
which is against the whole point of DTLSv1_listen. This change adds some
partial support for fragmented ClientHellos. It requires that the cookie
must be within the initial fragment. That way any non-initial ClientHello
fragments can be dropped and fragment reassembly is not required.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
The DTLSv1_listen function exposed details of the underlying BIO
abstraction and did not properly allow for IPv6. This commit changes the
"peer" argument to be a BIO_ADDR and makes it a first class function
(rather than a ctrl) to ensure proper type checking.
Reviewed-by: Richard Levitte <levitte@openssl.org>
The control commands that previously took a struct sockaddr * have
been changed to take a BIO_ADDR * instead.
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
PACKET contents should be read-only. To achieve this, also
- constify two user callbacks
- constify BUF_reverse.
Reviewed-by: Rich Salz <rsalz@openssl.org>
This was done by the following
find . -name '*.[ch]' | /tmp/pl
where /tmp/pl is the following three-line script:
print unless $. == 1 && m@/\* .*\.[ch] \*/@;
close ARGV if eof; # Close file to reset $.
And then some hand-editing of other files.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
This is an internal facility, never documented, not for
public consumption. Move it into ssl (where it's only used
for DTLS).
I also made the typedef's for pqueue and pitem follow our style: they
name structures, not pointers.
Reviewed-by: Richard Levitte <levitte@openssl.org>
The protocol selection code is now consolidated in a few consecutive
short functions in a single file and is table driven. Protocol-specific
constraints that influence negotiation are moved into the flags
field of the method structure. The same protocol version constraints
are now applied in all code paths. It is now much easier to add
new protocol versions without reworking the protocol selection
logic.
In the presence of "holes" in the list of enabled client protocols
we no longer select client protocols below the hole based on a
subset of the constraints and then fail shortly after when it is
found that these don't meet the remaining constraints (suiteb, FIPS,
security level, ...). Ideally, with the new min/max controls users
will be less likely to create "holes" in the first place.
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
if we have a malloc |x = OPENSSL_malloc(...)| sometimes we check |x|
for NULL and sometimes we treat it as a boolean |if(!x) ...|. Standardise
the approach in libssl.
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
This OPENSSL_assert in (d)tls1_hearbeat is trivially always going to be
true because it is testing the sum of values that have been set as
constants just a few lines above and nothing has changed them. Therefore
remove this.
Reviewed-by: Rich Salz <rsalz@openssl.org>
The function dtls1_link_min_mtu() was only used within d1_lib.c so make
it static.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
The SSL variable |in_handshake| seems misplaced. It would be better to have
it in the STATEM structure.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Adding the new state machine broke the DTLSv1_listen code because
calling SSL_in_before() was erroneously returning true after DTLSv1_listen
had successfully completed. This change ensures that SSL_in_before returns
false.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Change various state machine functions to use the prefix ossl_statem
instead.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Pull out the state machine into a separate sub directory. Also moved some
functions which were nothing to do with the state machine but were in state
machine files. Pulled all the SSL_METHOD definitions into one place...most
of those files had very little left in them any more.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
The DTLSv1_listen code set the state value explicitly to move into init.
Change to use state_set_in_init() instead.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Note that this commit constifies a user callback parameter and therefore
will break compilation for applications using this callback. But unless
they are abusing write access to the buffer, the fix is trivial.
Reviewed-by: Andy Polyakov <appro@openssl.org>
The existing implementation of DTLSv1_listen() is fundamentally flawed. This
function is used in DTLS solutions to listen for new incoming connections
from DTLS clients. A client will send an initial ClientHello. The server
will respond with a HelloVerifyRequest containing a unique cookie. The
client the responds with a second ClientHello - which this time contains the
cookie.
Once the cookie has been verified then DTLSv1_listen() returns to user code,
which is typically expected to continue the handshake with a call to (for
example) SSL_accept().
Whilst listening for incoming ClientHellos, the underlying BIO is usually in
an unconnected state. Therefore ClientHellos can come in from *any* peer.
The arrival of the first ClientHello without the cookie, and the second one
with it, could be interspersed with other intervening messages from
different clients.
The whole purpose of this mechanism is as a defence against DoS attacks. The
idea is to avoid allocating state on the server until the client has
verified that it is capable of receiving messages at the address it claims
to come from. However the existing DTLSv1_listen() implementation completely
fails to do this. It attempts to super-impose itself on the standard state
machine and reuses all of this code. However the standard state machine
expects to operate in a stateful manner with a single client, and this can
cause various problems.
A second more minor issue is that the return codes from this function are
quite confused, with no distinction made between fatal and non-fatal errors.
Most user code treats all errors as non-fatal, and simply retries the call
to DTLSv1_listen().
This commit completely rewrites the implementation of DTLSv1_listen() and
provides a stand alone implementation that does not rely on the existing
state machine. It also provides more consistent return codes.
Reviewed-by: Andy Polyakov <appro@openssl.org>
There are many places (nearly 50) where we malloc and then memset.
Add an OPENSSL_zalloc routine to encapsulate that.
(Missed one conversion; thanks Richard)
Also fixes GH328
Reviewed-by: Richard Levitte <levitte@openssl.org>
Just as with the OPENSSL_malloc calls, consistently use sizeof(*ptr)
for memset and memcpy. Remove needless casts for those functions.
For memset, replace alternative forms of zero with 0.
Reviewed-by: Richard Levitte <levitte@openssl.org>
For a local variable:
TYPE *p;
Allocations like this are "risky":
p = OPENSSL_malloc(sizeof(TYPE));
if the type of p changes, and the malloc call isn't updated, you
could get memory corruption. Instead do this:
p = OPENSSL_malloc(sizeof(*p));
Also fixed a few memset() calls that I noticed while doing this.
Reviewed-by: Richard Levitte <levitte@openssl.org>
