openssh/PROTOCOL

This documents OpenSSH's deviations and extensions to the published SSH
protocol.

Note that OpenSSH's sftp and sftp-server implement revision 3 of the SSH
filexfer protocol described in:

http://www.openssh.com/txt/draft-ietf-secsh-filexfer-02.txt

Features from newer versions of the draft are not supported, unless
explicitly implemented as extensions described below.

1. transport: Protocol 2 MAC algorithm "umac-64@openssh.com"

This is a new transport-layer MAC method using the UMAC algorithm
(rfc4418). This method is identical to the "umac-64" method documented
in:

http://www.openssh.com/txt/draft-miller-secsh-umac-01.txt

2. transport: Protocol 2 compression algorithm "zlib@openssh.com"

This transport-layer compression method uses the zlib compression
algorithm (identical to the "zlib" method in rfc4253), but delays the
start of compression until after authentication has completed. This
avoids exposing compression code to attacks from unauthenticated users.

The method is documented in:

http://www.openssh.com/txt/draft-miller-secsh-compression-delayed-00.txt

3. connection: Channel write close extension "eow@openssh.com"

The SSH connection protocol (rfc4254) provides the SSH_MSG_CHANNEL_EOF
message to allow an endpoint to signal its peer that it will send no
more data over a channel. Unfortunately, there is no symmetric way for
an endpoint to request that its peer should cease sending data to it
while still keeping the channel open for the endpoint to send data to
the peer.

This is desirable, since it saves the transmission of data that would
otherwise need to be discarded and it allows an endpoint to signal local
processes of the condition, e.g. by closing the corresponding file
descriptor.

OpenSSH implements a channel extension message to perform this
signalling: "eow@openssh.com" (End Of Write). This message is sent by an
endpoint when the local output of a channel is closed or experiences a
write error. The message is formatted as follows:

	byte		SSH_MSG_CHANNEL_REQUEST
	uint32		recipient channel
	string		"eow@openssh.com"
	boolean		FALSE

On receiving this message, the peer SHOULD cease sending data of
the channel and MAY signal the process from which the channel data
originates (e.g. by closing its read file descriptor).

As with the symmetric SSH_MSG_CHANNEL_EOF message, the channel does
remain open after a "eow@openssh.com" has been sent and more data may
still be sent in the other direction. This message does not consume
window space and may be sent even if no window space is available.

4. sftp: Reversal of arguments to SSH_FXP_SYMLINK

When OpenSSH's sftp-server was implemented, the order of the arguments
to the SSH_FXP_SYMLINK method was inadvertendly reversed. Unfortunately,
the reversal was not noticed until the server was widely deployed. Since
fixing this to follow the specification would cause incompatibility, the
current order was retained. For correct operation, clients should send
SSH_FXP_SYMLINK as follows:

	uint32		id
	string		targetpath
	string		linkpath

5. sftp: Server extension announcement in SSH_FXP_VERSION

OpenSSH's sftp-server lists the extensions it supports using the
standard extension announcement mechanism in the SSH_FXP_VERSION server
hello packet:

	uint32		3		/* protocol version */
	string		ext1-name
	string		ext1-version
	string		ext2-name
	string		ext2-version
	...
	string		extN-name
	string		extN-version

Each extension reports its integer version number as an ASCII encoded
string, e.g. "1". The version will be incremented if the extension is
ever changed in an incompatible way. The server MAY advertise the same
extension with multiple versions (though this is unlikely). Clients MUST
check the version number before attemping to use the extension.

6. sftp: Extension request "posix-rename@openssh.com"

This operation provides a rename operation with POSIX semantics, which
are different to those provided by the standard SSH_FXP_RENAME in
draft-ietf-secsh-filexfer-02.txt. This request is implemented as a
SSH_FXP_EXTENDED request with the following format:

	uint32		id
	string		"posix-rename@openssh.com"
	string		oldpath
	string		newpath

On receiving this request the server will perform the POSIX operation
rename(oldpath, newpath) and will respond with a SSH_FXP_STATUS message.
This extension is advertised in the SSH_FXP_VERSION hello with version
"1".

7. sftp: Extension requests "statvfs@openssh.com" and
         "fstatvfs@openssh.com"

These requests correspond to the statvfs and fstatvfs POSIX system
interfaces. The "statvfs@openssh.com" request operates on an explicit
pathname, and is formatted as follows:

	uint32		id
	string		"statvfs@openssh.com"
	string		path

The "fstatvfs@openssh.com" operates on an open filehandle:

	uint32		id
	string		"fstatvfs@openssh.com"
	string		handle

These requests return a SSH_FXP_STATUS reply on failure. On success they
return the following SSH_FXP_EXTENDED_REPLY reply:

	uint32		id
	uint32		f_bsize		/* file system block size */
	uint32		f_frsize	/* fundamental fs block size */
	uint64		f_blocks	/* number of blocks (unit f_frsize) */
	uint64		f_bfree		/* free blocks in file system */
	uint64		f_bavail	/* free blocks for non-root */
	uint64		f_files		/* total file inodes */
	uint64		f_ffree		/* free file inodes */
	uint64		f_favail	/* free file inodes for to non-root */
	uint32		f_fsid		/* file system id */
	uint32		f_flag		/* bit mask of f_flag values */
	uint32		f_namemax	/* maximum filename length */

The values of the f_flag bitmask are as follows:

	#define SSH_FXE_STATVFS_ST_RDONLY	0x1	/* read-only */
	#define SSH_FXE_STATVFS_ST_NOSUID	0x2	/* no setuid */

$Id: PROTOCOL,v 1.1 2008/05/19 06:11:56 djm Exp $