ntfs-3g/ntfsprogs/mkntfs.8.in

.\" -*- nroff -*-
.\" Copyright (c) 2001,2002 Anton Altaparmakov. All Rights Reserved.
.\" This file may be copied under the terms of the GNU Public License.
.\" Adapted from e2fsprogs-1.19/misc/mke2fs.8.in by Theodore Ts'o.
.\"
.TH MKNTFS 8 "March 2002" "Linux-NTFS version @VERSION@"
.SH NAME
mkntfs \- create a NTFS 1.2 (Windows NT/2000/XP) file system
.SH SYNOPSIS
.B mkntfs
[
.B \-s
.I sector-size
]
[
.B \-c
.I cluster-size
]
[
.B \-L
.I volume-label
]
[
.B \-z
.I mft-zone-multiplier
]
[
.B \-f
|
.B \-Q
]
[
.B -n
]
[
.B \-q
]
[
.B \-v
]
[
.B \-vv
]
[
.B \-C
]
[
.B \-F
]
[
.B \-I
]
[
.B \-V
]
[
.B \-l
]
[
.B \-h
]
.I device
[
.I number-of-sectors
]
.SH DESCRIPTION
.B mkntfs
is used to create a NTFS 1.2 (Windows NT 4.0) file system on a device (usually
a disk partition).
.I device
is the special file corresponding to the device (e.g
.IR /dev/hdXX ).
.I number-of-sectors
is the number of blocks on the device.  If omitted,
.B mkntfs
automagically figures the file system size.
.SH OPTIONS
.TP
.BI \-s " sector-size"
Specify the size of sectors in bytes. Valid sector size values are 256, 512,
1024, 2048 and 4096 bytes per sector. If omitted,
.B mkntfs
.I sector-size
is determined automatically and if that fails a default of 512
bytes per sector is used.
.TP
.BI \-c " cluster-size"
Specify the size of clusters in bytes. Valid cluster size values are powers of
two, with at least 256, and at most 65536 bytes per cluster. If omitted,
.B mkntfs
.I cluster-size
is determined by the volume size. The value is determined as
follows:
.TS
lB lB lB
l l r.
Volume	size	Default cluster
0	- 512MB	512 bytes
512MB	- 1GB	1024 bytes
1GB	- 2GB	2048 bytes
2GB	+	4096 bytes
.TE

Note that the default cluster size is set to be at least equal to the sector
size as a cluster cannot be smaller than a sector. Also, note that values
greater than 4096 have the side effect that compression is disabled on the
volume (due to limitations in the NTFS compression algorithm currently in use
by Windows).
.TP
.BI \-L " volume-label"
Set the volume label for the filesystem.
.TP
.BI \-z " mft-zone-multiplier"
Set the MFT zone multiplier, which determines the size of the MFT zone to use
on the volume. The MFT zone is the area at the beginning of the volume reserved
for the master file table (MFT), which stores the on disk inodes (MFT records).
It is noteworthy that small files are stored entirely within the inode;
thus, if you expect to use the volume for storing large numbers of very small
files, it is useful to set the zone multiplier to a higher value. Note, that
the MFT zone is resized on the fly as required during operation of the NTFS
driver but choosing a good value will reduce fragmentation. Valid values
are 1, 2, 3 and 4. The values have the following meaning:
.TS
lB lB
lB lB
c l.
MFT zone	MFT zone size
multiplier	(% of volume size)
1	12.5% (default)
2	25.0%
3	37.5%
4	50.0%
.TE
.TP
.B \-f
Same as
.BR \-Q .
.TP
.B \-Q
Perform quick format. This will skip both zeroing of the volume and bad sector
checking.
.TP
.B \-n
Causes
.B mkntfs
to not actually create a filesystem, but display what it would do if it were
to create a filesystem. All steps of the format are carried out except the
actual writing to the device.
.TP
.B \-q
Quiet execution; only errors are written to stderr, no output to stdout
occurs at all. Useful if
.B mkntfs
is run in a script.
.TP
.B \-v
Verbose execution.
.TP
.B \-vv
Really verbose execution; includes the verbose output from the
.B \-v
option as well as additional output useful for debugging
.B mkntfs.
.TP
.B \-C
Enable compression on the volume.
.TP
.B \-F
Force
.B mkntfs
to run, even if the specified
.I device
is not a block special device, or appears to be mounted.
.TP
.B \-I
Disable content indexing on the volume. (This is only meaningful on
Windows 2000 and later. Windows NT 4.0 and earlier ignore this as they do
not implement content indexing at all.)
.TP
.B \-V
Print the version number of
.B mkntfs
and exit.
.TP
.B \-l
Print the licensing information of
.B mkntfs
and exit.
.TP
.B \-h
Print the usage information of 
.B mkntfs
and exit.
.SH BUGS
.B mkntfs
writes the backup boot sector to the last sector of the block
.I device
being formatted. However, current versions of the Linux kernel (all versions
up to and including todays 2.4.18) either only report an even number of sectors
when the sector size is below 1024 bytes, which is the case for most hard
drives today (512 bytes sector size) or they return the correct number but
accessing the last sector fails. Either way, this means that when a partition
has an odd number of 512-byte sectors, the last sector is either not reported
to us at all or it is not writable by us and hence the created NTFS volume
will either have the backup boot sector placed one sector ahead of where it
should be or it cannot be written at all. For this reason,
.B mkntfs
marks the NTFS volume dirty, so that when you reboot into Windows, check disk
runs automatically and creates a copy of the backup boot sector in the correct
location. This also has the benefit of catching any bugs in
.B mkntfs
as check disk would find any corrupt structures and repair them, as well as
report them. - If you do see any problems reported, please report the messages
to the author.
.br
There may be other bugs. Please, report them to the author.
.SH AUTHOR
This version of
.B mkntfs
has been written by Anton Altaparmakov <aia21@cantab.net> (if that fails, use
<antona@users.sourceforge.net>).
.SH AVAILABILITY
.B mkntfs
is part of the Linux-NTFS project and is available for download from
http://sourceforge.net/project/showfiles.php?group_id=13956 in source (tar ball
and rpm) and pre-compiled binary (i386 rpm and deb) form.
.SH SEE ALSO
.BR badblocks (8),
.BR ntfsprogs (8)