mirror of
https://git.busybox.net/buildroot.git
synced 2024-11-27 07:23:30 +08:00
f816a35b18
This updates LEGO MINDSTORMS EV3 to Linux kernel 4.19 and U-Boot 2018.11. This kernel brings Bluetooth support, so some Bluez packages are also added. Also, we now have proper device tree support, so a few things are rearranged in the flash and SD card images since the DTB is no longer appended to the kernel image. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> |
||
|---|---|---|
| .. | ||
| busybox.fragment | ||
| genimage.cfg | ||
| linux.fragment | ||
| post-image.sh | ||
| readme.txt | ||
Lego Mindstorms EV3
Intro
=====
This is the buildroot basic board support for the Lego Mindstorms EV3
programmable brick.
The Lego Mindstorms EV3 brick comprises a Texas Instruments AM1808 SoC, with
an ARM 926EJ-S main processor running at 300 MHz.
See:
- https://en.wikipedia.org/wiki/Lego_Mindstorms_EV3
- http://www.lego.com/en-us/mindstorms/products/ev3/31313-mindstorms-ev3/
- http://www.ti.com/product/am1808
How it works
============
Boot process :
--------------
The EV3 boots from an EEPROM. This loads whatever is on the built-in 16MB flash
(usually U-Boot) and runs it. The U-Boot from the official LEGO firmware and
mainline U-Boot will attempt to boot a Linux kernel from the external µSD card.
It will try to load a uImage (and optional boot.scr) from the first µSD card
partition, which must be formatted with a FAT filesystem. If no µSD is found or
it does not contain a uImage file, then the EV3 will boot the uImage from the
built-in 16MB flash.
How to build it
===============
Configure Buildroot
-------------------
The lego_ev3_defconfig configuration provides basic support to boot on the Lego
Mindstorms EV3 programmable brick:
$ make lego_ev3_defconfig
Build everything
----------------
Note: you will need to have access to the network, since Buildroot will
download the packages' sources.
$ make
Result of the build
-------------------
After building, you should obtain this tree:
output/images/
├── boot.vfat
├── flash.bin
├── rootfs.ext2
├── rootfs.ext3 -> rootfs.ext2
├── rootfs.squashfs
├── sdcard.img
├── u-boot.bin
├── uImage -> uImage.da850-lego-ev3
└── uImage.da850-lego-ev3
Installation
============
You can use either flash.bin or the sdcard.img. To load flash.bin, use the
official Lego Mindstorms EV3 programming software firmware update tool to load
the image. To use sdcard.img, use a disk writing tool such as Etcher or dd to
write the image to the µSD card.
NOTE: The sdcard.img created by lego_ev3_defconfig won't boot if the official
LEGO firmware is installed on the EV3 (it has an old version of U-Boot that
doesn't know about device tree). You must either set the kernel configuration
option to append the device tree to the kernel or you can create a boot.scr
that chainloads a newer U-Boot or you can install a newer U-Boot in the flash
memory (just flashing u-boot.bin is enough).
Finish
======
To have a serial console, you will need a proper USB to Lego serial port
adapter plugged into the EV3 sensors port 1.
See:
- http://botbench.com/blog/2013/08/15/ev3-creating-console-cable/
- http://botbench.com/blog/2013/08/05/mindsensors-ev3-usb-console-adapter/
The serial port config to use is 115200/8-N-1.
Bluetooth
=========
To enable Bluetooth:
# modprobe hci_uart
# /usr/libexec/bluetooth/bluetoothd &
# bluetoothctl
[bluetooth]# power on