mirror of
https://git.busybox.net/buildroot.git
synced 2024-11-23 05:23:39 +08:00
configs/globalscale_espressobin: new defconfig
Basic support for the Marvell ESPRESSObin, by Globalscale Technologies. http://espressobin.net The kernel config has been extended with a fragment to enable switchcore support, DSA drivers, and VLAN filtering in the bridge. To make use of this you need a custom libnl based application, or the iproute2 suite rather than the brctl tools, which don't support the VLAN filtering. Signed-off-by: Joachim Nilsson <troglobit@gmail.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit is contained in:
Joachim Nilsson
Thomas Petazzoni
parent
d0fb813539
commit
1c714bf757
@ -198,6 +198,7 @@ friendlyarm_nanopi_a64_defconfig: { extends: .defconfig }
|
||||
friendlyarm_nanopi_neo2_defconfig: { extends: .defconfig }
|
||||
friendlyarm_nanopi_neo_plus2_defconfig: { extends: .defconfig }
|
||||
galileo_defconfig: { extends: .defconfig }
|
||||
globalscale_espressobin_defconfig: { extends: .defconfig }
|
||||
grinn_chiliboard_defconfig: { extends: .defconfig }
|
||||
grinn_liteboard_defconfig: { extends: .defconfig }
|
||||
hifive_unleashed_defconfig: { extends: .defconfig }
|
||||
|
||||
@ -1271,6 +1271,10 @@ F: package/libuhttpd/
|
||||
F: package/libuwsc/
|
||||
F: package/rtty/
|
||||
|
||||
N: Joachim Nilsson <troglobit@gmail.com>
|
||||
F: configs/globalscale_espressobin_defconfig
|
||||
F: board/globalscale/espressobin/
|
||||
|
||||
N: Joao Pinto <jpinto@synopsys.com>
|
||||
F: board/synopsys/vdk/
|
||||
F: configs/snps_aarch64_vdk_defconfig
|
||||
|
||||
11
board/globalscale/espressobin/genimage.cfg
Normal file
11
board/globalscale/espressobin/genimage.cfg
Normal file
@ -0,0 +1,11 @@
|
||||
# Minimal image, no U-boot since v3/v5 cannot boot from sdcard, see
|
||||
# readme.txt for details on configuring the on-board u-boot.
|
||||
image sdcard.img {
|
||||
hdimage {
|
||||
}
|
||||
|
||||
partition rootfs {
|
||||
partition-type = 0x83
|
||||
image = "rootfs.ext4"
|
||||
}
|
||||
}
|
||||
14
board/globalscale/espressobin/linux-extras.config
Normal file
14
board/globalscale/espressobin/linux-extras.config
Normal file
@ -0,0 +1,14 @@
|
||||
#
|
||||
# The Espressobin has a switchcore with full support in the kernel.
|
||||
# This fragment enables DSA and its drivers, inclding VLAN aware bridge
|
||||
# support to allow users to easily set up a LAN switch + WAN interface.
|
||||
#
|
||||
CONFIG_NET_DSA=m
|
||||
CONFIG_VLAN_8021Q=y
|
||||
|
||||
CONFIG_BRIDGE=m
|
||||
CONFIG_BRIDGE_IGMP_SNOOPING=y
|
||||
CONFIG_BRIDGE_VLAN_FILTERING=y
|
||||
|
||||
CONFIG_NET_DSA_MV88E6XXX=m
|
||||
CONFIG_NET_DSA_MV88E6XXX_PTP=y
|
||||
90
board/globalscale/espressobin/readme.txt
Normal file
90
board/globalscale/espressobin/readme.txt
Normal file
@ -0,0 +1,90 @@
|
||||
Marvell ESPRESSObin
|
||||
===================
|
||||
|
||||
This default configuration allows you to quickly get up and running with
|
||||
the Marvell ESPRESSObin board by Globalscale Technologies Inc.
|
||||
|
||||
The ESPRESSObin is based on the Marvell Armada 88F3720 SoC, coupled with
|
||||
a Marvell 88E6341 switch core "Topaz", with three exposed gigabit ports.
|
||||
|
||||
_________________________
|
||||
|# U W L L U #|
|
||||
|# S A A A S #|
|
||||
|# B N N N B #|
|
||||
|# 0 1 #|
|
||||
|# Mini #|
|
||||
|# -PCI #|
|
||||
|# #|
|
||||
|# 5 #|
|
||||
|#__V___usb_PWR_SATA__SW_#|
|
||||
|
||||
Fig 1: Overview of board
|
||||
|
||||
Notice difference in Ethernet port layout compared to the Globalscale
|
||||
docs. They order the ports; LAN2, LAN1, WAN (left to right in figure
|
||||
above). For more information, see http://espressobin.net
|
||||
|
||||
|
||||
Building
|
||||
--------
|
||||
|
||||
$ make globalscale_espressobin_defconfig
|
||||
$ make
|
||||
|
||||
This generates the kernel image, the devicetree binary, the rootfs as a
|
||||
tar.gz, and a filesystem image containing everything.
|
||||
|
||||
All build artifacts are located in `output/images/`
|
||||
|
||||
|
||||
Booting
|
||||
-------
|
||||
|
||||
To boot, you need a UART connection, using the on-board micro USB port
|
||||
set to 115200 8N1.
|
||||
|
||||
By default, the ESPRESSObin comes with a pre-flashed U-Boot set up to
|
||||
load the kernel, device-tree and rootfs from SPI NOR flash. The board
|
||||
jumpers can be changed to boot from different sources, see the quick
|
||||
start guide for each board revision for details:
|
||||
|
||||
- ftp://downloads.globalscaletechnologies.com/Downloads/Espressobin/ESPRESSObin%20V5/
|
||||
- ftp://downloads.globalscaletechnologies.com/Downloads/Espressobin/ESPRESSObin%20V7/
|
||||
|
||||
Note: the v5, and earlier, cannot boot from sdcard, so you have to set
|
||||
up the factory U-Boot to boot into Buildroot:
|
||||
|
||||
1. Flash rootfs image to sdcard drive, your `of=` device may differ:
|
||||
|
||||
$ sudo dd if=output/images/sdcard.img of=/dev/mmcblk0 bs=1M
|
||||
$ sync
|
||||
|
||||
2. Boot board from SPI NOR, interrupt boot by pressing any key ...
|
||||
3. Check with `printenv` that the default setup is OK, otherwise ensure
|
||||
the following are set, and define `bootcmd` for automatic boot:
|
||||
|
||||
> setenv kernel_addr 0x5000000
|
||||
> setenv fdt_addr 0x1800000
|
||||
> setenv fdt_name boot/armada-3720-espressobin.dtb
|
||||
> setenv console console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000
|
||||
> setenv bootcmd 'mmc dev 0; ext4load mmc 0:1 $kernel_addr $image_name;ext4load mmc 0:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk0p1 rw rootwait; booti $kernel_addr - $fdt_addr'
|
||||
|
||||
4. Call the boot command, or `reset` the board to start:
|
||||
|
||||
> run bootcmd
|
||||
|
||||
|
||||
Networking
|
||||
----------
|
||||
|
||||
To enable Ethernet networking, load the `mv88e6xxx` kernel module, and
|
||||
bring up each respective interface needed:
|
||||
|
||||
# modprobe mv88e6xxx
|
||||
# ifconfig wan up
|
||||
|
||||
A more advanced scenario is setting up switching between the ports using
|
||||
the Linux bridge. The kernel switchdev layer, and DSA driver, ensure
|
||||
switch functions are "offloaded" to the HW switch, i.e., all traffic
|
||||
between LAN ports never reach the CPU. For this you need the iproute2
|
||||
suite of tools.
|
||||
26
configs/globalscale_espressobin_defconfig
Normal file
26
configs/globalscale_espressobin_defconfig
Normal file
@ -0,0 +1,26 @@
|
||||
BR2_aarch64=y
|
||||
BR2_cortex_a53=y
|
||||
BR2_ARM_FPU_VFPV4=y
|
||||
|
||||
# Linux headers same as kernel, a 5.6 series
|
||||
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_6=y
|
||||
|
||||
# Kernel
|
||||
BR2_LINUX_KERNEL=y
|
||||
BR2_LINUX_KERNEL_CUSTOM_VERSION=y
|
||||
BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.6.11"
|
||||
BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
|
||||
BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="board/globalscale/espressobin/linux-extras.config"
|
||||
BR2_LINUX_KERNEL_DTS_SUPPORT=y
|
||||
BR2_LINUX_KERNEL_INTREE_DTS_NAME="marvell/armada-3720-espressobin marvell/armada-3720-espressobin-emmc marvell/armada-3720-espressobin-v7 marvell/armada-3720-espressobin-v7-emmc"
|
||||
BR2_LINUX_KERNEL_INSTALL_TARGET=y
|
||||
|
||||
# Filesystem
|
||||
BR2_TARGET_GENERIC_ISSUE="Welcome to Buildroot for the Marvell ESPRESSObin"
|
||||
BR2_TARGET_ROOTFS_EXT2=y
|
||||
BR2_TARGET_ROOTFS_EXT2_4=y
|
||||
BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
|
||||
BR2_TARGET_ROOTFS_TAR_GZIP=y
|
||||
BR2_PACKAGE_HOST_GENIMAGE=y
|
||||
BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh"
|
||||
BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/globalscale/espressobin/genimage.cfg"
|
||||
Loading…
Reference in New Issue
Block a user