* sh3-rom.c (_initialize_sh3_rom): Get rid of specific _WINDOWS
conditional for help with connections through parallel ports,
given that the actual code for downloading through a parallel port
is not conditionalized.
* sh-tdep.c: Remove WIN32_WCE conditional. The wince sh target is
unmaintaned, and probably on its way to obsolescence.
arch-utils.{h,c}. The ``set architecutre'' and ``set endian''
commands (part of the move) were implemented to use add_set_enum_cmd()
so that ``set architecture <tab>'' works.
be consistent with GCC.
(FPUL_REGNUM, etc): Renumber to match list changes.
(ADDR_BITS_REMOVE): Delete.
* sh-tdep.c (sh_reg_names, sh3_reg_names, sh3e_reg_names):
Rearrange to match REGISTER_NAMES.
* sh3-rom.c (sh3_regnames, sh3e_regnames): Ditto.
PR 9457
like EST visionICE that send back an ACK after each S-record.
* monitor.c (monitor_wait_srec_ack): New function.
(monitor_load): Pass monitor_wait_srec_ack to load_srec
if the monitor's MO_SREC_ACK flag is set.
* monitor.h: Define MO_SREC_ACK flag.
* remote-est.c (est_cmds): Add MO_SREC_ACK flag.
* sh3-rom.c (sh3_load): Accomodate change in load_srec prototype.
* srec.h: Add WAITACK parameter to load_srec prototype.
* sh-tdep.c (set processor): New command to set specific
processor type.
(sh_reg_names, sh3_reg_names): Arrays of register names for
SH and SH3 processors.
(sh_set_processor_type): New function.
* sh3-rom.c (sh3_open): Call it.
(sh3_regname): Add names of all the bank registers.
(sh3_supply_register): Clean up formatting.
* config/sh/tm-sh.h (NUM_REGS, NUM_REALREGS): Increase to include
bank registers.
(REGISTER_NAMES): Add names of bank registers.
(FP15_REGNUM): Define.
(REGISTER_VIRTUAL_TYPE): Use it.
* monitor.c: Clean up some comments.
S-record download code into srec.c.
* srec.c srec.h: New files. Contain S-record loading routines
formerly in monitor.c.
* serial.c serial.h: New routine just like fprintf, but uses
serial_t instead of FILE *.
* sh-tdep.c (frame_find_saved_regs init_extra_frame_info):
Don't add four to saved pc (makes things match manual). Also, fix
bug where we didn't get pc from stack frame correctly.
* config/sh/tm-sh.h (SAVED_PC_AFTER_CALL): Don't add four to
saved pc. Real hardware does this for you.
* sh3-rom.c (sh3_load): New routine. Sets up for download then
calls generic S-record loader.
* config/h8300/h8300.mt, config/h8500/h8500.mt,
config/m68k/monitor.mt, config/pa/hppapro.mt, config/sh/sh.mt:
Add srec.o to TDEPFILES.
with the obvious extension. (monitor_read_memory_single): Use
regexp for getmem.resp_delim because of parsing ambiguities caused
by certain monitors. (monitor_read_memory): Use new regexp stuff
to parse getmem.resp_delim.
* sh3-rom.c: Finish off table. Use new regexp capability for
getmem commands.
sh3 monitor support.
* monitor.c: Cleanup regexp compilation stuff to make it easier
to use several regexps.
* monitor.h: Get rid of struct rom_cmd_data. It's no longer used.
* config/m68k/tm-monitor.h: Don't redefine NUM_REGS here. It just
causes GDB to crash.
