This patch adds initial 64-bit insn assembler/disassembler support.
The only instruction added is "pnop" along with the automatic aligning
of prefix instruction so they do not cross 64-byte boundaries.
include/
* dis-asm.h (WIDE_OUTPUT): Define.
* opcode/ppc.h (prefix_opcodes, prefix_num_opcodes): Declare.
(PPC_OPCODE_POWERXX, PPC_GET_PREFIX, PPC_GET_SUFFIX),
(PPC_PREFIX_P, PPC_PREFIX_SEG): Define.
opcodes/
* ppc-dis.c (ppc_opts): Add "future" entry.
(PREFIX_OPCD_SEGS): Define.
(prefix_opcd_indices): New array.
(disassemble_init_powerpc): Initialize prefix_opcd_indices.
(lookup_prefix): New function.
(print_insn_powerpc): Handle 64-bit prefix instructions.
* ppc-opc.c (PREFIX_OP, PREFIX_FORM, SUFFIX_MASK, PREFIX_MASK),
(PMRR, POWERXX): Define.
(prefix_opcodes): New instruction table.
(prefix_num_opcodes): New constant.
binutils/
* objdump.c (disassemble_bytes): Set WIDE_OUTPUT in flags.
gas/
* config/tc-ppc.c (ppc_setup_opcodes): Handle prefix_opcodes.
(struct insn_label_list): New.
(insn_labels, free_insn_labels): New variables.
(ppc_record_label, ppc_clear_labels, ppc_start_line_hook): New funcs.
(ppc_frob_label, ppc_new_dot_label): Move functions earlier in file
and call ppc_record_label.
(md_assemble): Handle 64-bit prefix instructions. Align labels
that are on the same line as a prefix instruction.
* config/tc-ppc.h (tc_frob_label, ppc_frob_label): Move to
later in the file.
(md_start_line_hook): Define.
(ppc_start_line_hook): Declare.
* testsuite/gas/ppc/prefix-align.d,
* testsuite/gas/ppc/prefix-align.s: New test.
* testsuite/gas/ppc/ppc.exp: Run new test.
This patch fixes a problem with disassembly of branch instructions
for processors complying with PowerPC ISA versions prior to version
2.0, ie. those that use "y" bit branch taken hints. Many of the
extended bcctr and bclr mnemonics that should have disassembled with a
"-" suffix, ie. not taken, did not display the "-" due to the ordering
in powerpc_opcodes. I believe it's been that way from the original
85dcf36d72 commit of ppc-opc.c.
I've also added a BH field (optional) to a few opcodes. This gives
better disassembly in raw mode, showing the branch taken hint in the
mnemonic as is done for bc. It would be reasonable to add a BH
field to all bcctr, bclr, and bctar extended mnemonics but that runs
into a small difficulty: Currently we print all or none of the
optional operands. That means for example that "bgectr cr2" would
display as "bgectr cr2,0" if a BH field is added to bgectr.
* ppc-opc.c (XLBH_MASK): Subtract off BH field from BB_MASK.
(powerpc_opcodes): Reorder bcctr and bclr extended mnemonics
to favour printing of "-" branch hint when using the "y" bit.
Allow BH field on bc{ctr,lr,tar}{,l}{-,+}.
"mtfsb0 4*cr7+lt" doesn't make all that much sense, but unfortunately
glibc uses just that instead of "mtfsb0 28" to clear the fpscr xe bit.
So for backwards compatibility accept cr field expressions when
assembling mtfsb operands, but disassemble to a plain number.
PR 24390
include/
* opcode/ppc.h (PPC_OPERAND_CR_REG): Comment.
opcodes/
* ppc-opc.c (BTF): Define.
(powerpc_opcodes): Use for mtfsb*.
* ppc-dis.c (print_insn_powerpc): Print fields with both
PPC_OPERAND_CR_REG and PPC_OPERAND_CR_BIT as a plain number.
gas/
* testsuite/gas/ppc/476.d: Update mtfsb*.
* testsuite/gas/ppc/a2.d: Likewise.
The instruction mask bits should never overlap any of the operands,
nor should operand bits overlap, but some operands weren't checked.
This patch arranges to check the omitted operands, using a mask
returned by the operand->insert function. Some tweaking of various
insert functions is needed to support this: The error case must set
field bits.
Since I was looking at the insert functions, I tidied some dead code
and simplified some of the powerpc_operands entries.
gas/
* config/tc-ppc.c (insn_validate): Don't ignore mask in
PPC_OPSHIFT_INV case. Call the insert function to calculate
a mask.
opcodes/
* ppc-opc.c (insert_arx, insert_ary, insert_rx, insert_ry, insert_ls),
(insert_evuimm1_ex0, insert_evuimm2_ex0, insert_evuimm4_ex0),
(insert_evuimm8_ex0, insert_evuimm_lt8, insert_evuimm_lt16),
(insert_rD_rS_even, insert_off_lsp, insert_off_spe2, insert_Ddd):
Don't return zero on error, insert mask bits instead.
(insert_sd4h, extract_sd4h, insert_sd4w, extract_sd4w): Delete.
(insert_sh6, extract_sh6): Delete dead code.
(insert_sprbat, insert_sprg): Use unsigned comparisions.
(powerpc_operands <OIMM>): Set shift count rather than using
PPC_OPSHIFT_INV.
<SE_SDH, SE_SDW>: Likewise. Don't use insert/extract functions.
Most optional operands to powerpc instructions use a default value of
zero, but there are a few exceptions. Those have been handled by
PPC_OPERAND_OPTIONAL_VALUE and an entry in the powerpc_operands table
for the default value, smuggled in the shift field. This patch
changes that to using the operand extract function to provide non-zero
defaults.
I've also moved the code determining whether optional operands are
provided or omitted, to the point the first optional operand is seen,
and allowed for the possibility of optional base register operands
in a future patch.
The patch does change the error you get on invalid assembly like
ld 3,4
You'll now see "missing operand" rather than
"syntax error; end of line, expected `('".
gas/
* config/tc-ppc.c (md_assemble): Delay counting of optional
operands until one is encountered. Allow for the possibility
of optional base regs, ie. PPC_OPERAND_PARENS. Call
ppc_optional_operand_value with extra args.
include/
* opcode/ppc.h (struct powerpc_operand): Correct "insert" comment.
Mention use of "extract" function to provide default value.
(PPC_OPERAND_OPTIONAL_VALUE): Delete.
(ppc_optional_operand_value): Rewrite to use extract function.
opcodes/
* ppc-dis.c (operand_value_powerpc): Init "invalid".
(skip_optional_operands): Count optional operands, and update
ppc_optional_operand_value call.
* ppc-opc.c (extract_dxdn): Remove ATTRIBUTE_UNUSED from used arg.
(extract_vlensi): Likewise.
(extract_fxm): Return default value for missing optional operand.
(extract_ls, extract_raq, extract_tbr): Likewise.
(insert_sxl, extract_sxl): New functions.
(insert_esync, extract_esync): Remove Power9 handling and simplify.
(powerpc_operands <FXM4, TBR>): Delete PPC_OPERAND_OPTIONAL_VALUE
flag and extra entry.
(powerpc_operands <SXL>): Likewise, and use insert_sxl and
extract_sxl.
PowerPC has replaced use of "long" for insns with "int64_t", in
preparation for 64-bit power10 insns.
* ppc-opc.c (insert_sprbat): Correct function parameter and
return type.
(extract_sprbat): Likewise, variable too.
This is a relatively straightforward patch to improve support for the
IBM Gekko and IBM Broadway processors. Broadway is functionally
equivalent to the IBM 750CL, while Gekko's functionality is a subset
of theirs. The patch simplifies this reality and adds -mgekko and
-mbroadway as aliases for -m750cl. I didn't feel it was worth wasting
a PPC_OPCODE_* bit to differentiate Gekko. The patch adds a number of
simplified mnemonics for special purpose register access. Notably,
Broadway adds 4 additional IBAT and DBAT registers but these are not
assigned sequential SPR numbers.
gas/
* config/tc-ppc.c (md_show_usage): Add -mgekko and -mbroadway.
* doc/as.texi (Target PowerPC options): Add -mgekko and -mbroadway.
* doc/c-ppc.texi (PowerPC-Opts): Likewise.
* testsuite/gas/ppc/broadway.d,
* testsuite/gas/ppc/broadway.s: New test for broadway.
* testsuite/gas/ppc/ppc.exp: Run new test.
include/
* opcode/ppc.h (PPC_OPCODE_750): Adjust comment.
opcodes/
* ppc-dis.c (ppc_opts): Add -mgekko and -mbroadway.
(powerpc_init_dialect): Handle bfd_mach_ppc_750.
* ppc-opc.c (insert_sprbat, extract_sprbat): New functions to
support disjointed BAT.
(powerpc_operands): Allow extra bit in SPRBAT_MASK. Add SPRGQR.
(XSPRGQR_MASK, GEKKO, BROADWAY): Define.
(powerpc_opcodes): Add 750cl extended mnemonics for spr access.
opcodes/
* ppc-opc.c (vle_opcodes): Add e_lmvsprw, e_lmvgprw,
e_lmvsrrw, e_lmvcsrrw and e_lmvcsrrw as official mnemonics for
VLE multimple load/store instructions. Old e_ldm* variants are
kept as aliases.
Add missing e_lmvmcsrrw and e_stmvmcsrrw.
gas/
* testsuite/gas/ppc/vle-mult-ld-st-insns.s: New file: Tests the
support for the VLE multiple load/store instructions.
* testsuite/gas/ppc/vle-mult-ld-st-insns.d: New file: Test
driver.
* testsuite/gas/ppc/ppc.exp: Run it.
* ppc-opc.c: Formatting and comment fixes. Move insert and
extract functions earlier, deleting forward declarations.
(insert_nbi, insert_raq, insert_rbx): Expand use of RT_MASK and
RA_MASK.
PPC_OPCODE_* renumbered to fill the gaps left by previous patches,
and reordered chronologically just because. I kept PPC_OPCODE_TMR
because presumably it might be used in future APUinfo for e6500.
include/
* opcode/ppc.h (PPC_OPCODE_*): Renumber and order chronologically.
(PPC_OPCODE_SPE): Comment on this and other bits used for APUinfo.
opcodes/
* ppc-dis.c (ppc_opts): Formatting. Set PPC_OPCODE_TMR for e6500.
* ppc-opc.c (powerpc_opcodes <mftmr, mttmr>): Remove now
unnecessary E6500.
This bit is also useless as it can be replaced with PPC_OPCODE_POWER9.
Defining the VSX2 and VSX3 selection based on cpu bits also lets the
assembler/disassembler distinguish between the power7 VSX opcodes and
the power8 ones. Note that this change means -mvsx now reverts back
to just adding the power7 VSX insns.
include/
* opcode/ppc.h (PPC_OPCODE_VSX3): Delete.
opcodes/
* ppc-dis.c (ppc_opts): Remove PPC_OPCODE_VSX3.
* ppc-opc.c (PPCVSX2): Define as PPC_OPCODE_POWER8.
(PPCVSX3): Define as PPC_OPCODE_POWER9.
This bit is worse than useless. Using it prevents the assembler and
disassembler distinguishing between opcodes added for power8 and those
added for power9.
include/
* opcode/ppc.h (PPC_OPCODE_ALTIVEC2): Delete.
opcodes/
* ppc-dis.c (ppc_opts): Remove PPC_OPCODE_ALTIVEC2.
* ppc-opc.c (PPCVEC2): Define as PPC_OPCODE_POWER8|PPC_OPCODE_E6500.
(PPCVEC3): Define as PPC_OPCODE_POWER9.
PPC_OPCODE_440 being set for ppc476 meant that many opcodes needed to
be deprecated for ppc476. There are far fewer to add specially for
ppc476 if PPC_OPCODE_440 is not set for ppc476.
* ppc-dis.c (ppc_opts <476>): Remove PPC_OPCODE_440.
* ppc-opc.c (MULHW): Add PPC_OPCODE_476.
(powerpc_opcodes): Adjust PPC440, PPC464 and PPC476 insns to suit
removal of PPC_OPCODE_440 from ppc476 cpu selection bits.
PR 21248
* ppc-opc.c (powerpc_opcodes): Enable mfivor32, mfivor33,
mtivor32, and mtivor33 for e6500. Move mfibatl and mfibatu after
those spr mnemonics they alias. Similarly for mtibatl, mtibatu.
Certain insns have restrictions on fields. For example, the insn
mentioned in the PR, lqarx, must specify an even general purpose
register as its destination and that register cannot appear in
either of the base or index reg fields. This holds even when the RA0
field is 0 (meaning a zero rather than r0).
PR 21124
* ppc-opc.c (extract_esync, extract_ls, extract_ral, extract_ram)
(extract_raq, extract_ras, extract_rbx): New functions.
(powerpc_operands): Use opposite corresponding insert function.
(Q_MASK): Define.
(powerpc_opcodes): Apply Q_MASK to all quad insns with even
register restriction.
This stops powerpc gas blithely accepting such nonsense as
"addi %f4,%cr3,%r31".
PR 21118
gas/
* NEWS: Mention powerpc register checks.
* config/tc-ppc.c (struct pd_reg): Make value a short. Add flags.
(pre_defined_registers): Delete fpscr and pmr entries. Set
register type in flags.
(cr_names): Set type in flags.
(reg_name_search): Return pointer to struct pd_reg rather than value.
(register_name): Adjust to suit. Set X_md from flags.
(ppc_parse_name): Likewise.
(ppc_optimize_expr): New function.
(md_assemble): Verify expresion reg flags match operand.
* config/tc-ppc.h (md_optimize_expr): Define.
(ppc_optimize_expr): Declare.
include/
* opcode/ppc.h (PPC_OPERAND_*): Reassign values, regs first.
(PPC_OPERAND_SPR, PPC_OPERAND_GQR): Define.
opcodes/
* ppc-opc.c (powerpc_operands): Flag SPR, SPRG and TBR entries
with PPC_OPERAND_SPR. Flag PSQ and PSQM with PPC_OPERAND_GQR.
cmp[l][o] get an optional L field only when generating 32-bit code.
dcbf, tlbie and tlbiel keep their optional L field, ditto for R field
of tbegin. cmprb, tsr., wlcr[all] and mtsle all change to a
compulsory L field.
L field of dcbf and wclr is 2 bits.
PR 20641
include/
* opcode/ppc.h (PPC_OPERAND_OPTIONAL32): Define.
opcodes/
* ppc-opc.c (L): Make compulsory.
(LOPT): New, optional form of L.
(HTM_R): Define as LOPT.
(L0, L1): Delete.
(L32OPT): New, optional for 32-bit L.
(L2OPT): New, 2-bit L for dcbf.
(SVC_LEC): Update.
(L2): Define.
(insert_l0, extract_l0, insert_l1, extract_l2): Delete.
(powerpc_opcodes <cmpli, cmpi, cmpl, cmp>): Use L32OPT.
<dcbf>: Use L2OPT.
<tlbiel, tlbie>: Use LOPT.
<wclr, wclrall>: Use L2.
gas/
* config/tc-ppc.c (md_assemble): Handle PPC_OPERAND_OPTIONAL32.
* testsuite/gas/ppc/power8.s: Provide tbegin. operand.
* testsuite/gas/ppc/power9.d: Update cmprb disassembly.
VLE is an encoding, not a particular processor architecture, so it
isn't really proper to select insns based on PPC_OPCODE_VLE. For
example
{"evaddw", VX (4, 512), VX_MASK, PPCSPE|PPCVLE, PPCNONE, {RS, RA, RB}},
{"vaddubs", VX (4, 512), VX_MASK, PPCVEC|PPCVLE, PPCNONE, {VD, VA, VB}},
shows two insns that have the same encoding, both available with VLE.
Enabling both with VLE means we can't disassemble the second variant
even if -Maltivec is given rather than -Mspe. Also, we don't check
user assembly against the processor type as well as we could.
Another problem is that when using the VLE encoding, insns from the
main ppc opcode table are not available, except those using opcode 4
and 31. Correcting this revealed two errors in the ld testsuite,
use of "nop" and "rfmci" when -mvle.
This patch fixes those problems in the opcode table, and removes
PPCNONE. I find a plain 0 distracts less from other values.
In addition, I've implemented code to recognize some machine values
from the apuinfo note present in ppc32 objects. It's not a complete
disambiguation since we're lacking info to detect newer chips, but
what we have should help with disassembly.
include/
* elf/ppc.h (APUINFO_SECTION_NAME, APUINFO_LABEL, PPC_APUINFO_ISEL,
PPC_APUINFO_PMR, PPC_APUINFO_RFMCI, PPC_APUINFO_CACHELCK,
PPC_APUINFO_SPE, PPC_APUINFO_EFS, PPC_APUINFO_BRLOCK,
PPC_APUINFO_VLE: Define.
opcodes/
* ppc-dis.c (ppc_opts): Delete extraneous parentheses. Default
cpu for "vle" to e500.
* ppc-opc.c (ALLOW8_SPRG): Remove PPC_OPCODE_VLE.
(NO371, PPCSPE, PPCISEL, PPCEFS, MULHW, DCBT_EO): Likewise.
(PPCNONE): Delete, substitute throughout.
(powerpc_opcodes): Remove PPCVLE from "flags". Add to "deprecated"
except for major opcode 4 and 31.
(vle_opcodes <se_rfmci>): Add PPCRFMCI to flags.
bfd/
* cpu-powerpc.c (powerpc_compatible): Allow bfd_mach_ppc_vle entry
to match other 32-bit archs.
* elf32-ppc.c (_bfd_elf_ppc_set_arch): New function.
(ppc_elf_object_p): Call it.
(ppc_elf_special_sections): Use APUINFO_SECTION_NAME. Fix
overlong line.
(APUINFO_SECTION_NAME, APUINFO_LABEL): Don't define here.
* elf64-ppc.c (ppc64_elf_object_p): Call _bfd_elf_ppc_set_arch.
* bfd-in.h (_bfd_elf_ppc_at_tls_transform,
_bfd_elf_ppc_at_tprel_transform): Move to..
* elf-bfd.h: ..here.
(_bfd_elf_ppc_set_arch): Declare.
* bfd-in2.h: Regenerate.
gas/
* config/tc-ppc.c (PPC_APUINFO_ISEL, PPC_APUINFO_PMR,
PPC_APUINFO_RFMCI, PPC_APUINFO_CACHELCK, PPC_APUINFO_SPE,
PPC_APUINFO_EFS, PPC_APUINFO_BRLOCK, PPC_APUINFO_VLE): Don't define.
(ppc_setup_opcodes): Check vle disables powerpc_opcodes overridden
by vle_opcodes, and that vle flag doesn't enable opcodes. Don't
add vle_opcodes twice.
(ppc_cleanup): Use APUINFO_SECTION_NAME and APUINFO_LABEL.
ld/
* testsuite/ld-powerpc/apuinfo1.s: Delete nop.
* testsuite/ld-powerpc/apuinfo-vle2.s: New.
* testsuite/ld-powerpc/powerpc.exp: Use apuinfo-vle2.s.
This is a workaround for a gcc bug.
PR 19359
* ppc-opc.c (insert_fxm): Remove "ignored" from error message.
(powerpc_opcodes): Remove single-operand mfcr.
The idea being to put instructions that have the same encoding adjacent
to each other.
* opcodes/ppc-opc.c (powerpc_opcodes): Sort power9 insns by
major opcode/xop.
