The current space optmization on enum aarch64_opn_qualifier forced its
encoding using an unsigned char. This "hard-coded" optimization has the
bad consequence of making the array of such enums being completely
unreadable when debugging with GDB because the enum type is lost along
the way.
Keeping this space optimization, and the enum type as well, is possible
when the declaration of the enum is tagged with attribute((packed)).
attribute((packed)) is a GNU extension, and is wrapped in the macro
ATTRIBUTE_PACKED (defined in ansidecl.h), and should be used instead.
The enum aarch64_opnd_qualifiers in include/opcode/aarch64.h needs to
stay in sync with the array of struct operand_qualifier_data which
defines various properties for the different type of operands. For
instance, for:
- registers: the size of the register, the number of elements.
- immediates: lower and upper bits to determine the range of values.
For any arm elf target, disable an old piece of code that forced disassembly to
disassemble for 'unknown architecture' which once upon a time meant it would
disassemble ANY arm instruction. This is no longer true with the addition of
Armv8.1-M Mainline, as there are conflicting encodings for different thumb
instructions.
BFD however can detect what architecture the object file was assembled for
using information in the notes section. So if available, we use that,
otherwise we default to the old 'unknown' behaviour.
With the changes above code, a mode changing 'bx lr' assembled for armv4 with
the option --fix-v4bx will result in an object file that is recognized by bfd
as one for the armv4 architecture. The disassembler now disassembles this
encoding as a BX even for Armv4 architectures, but warns the user when
disassembling for Armv4 that this instruction is only valid from Armv4T
onwards.
Remove the unused and wrongfully defined ARM_ARCH_V8A_CRC, and
define and use a ARM_ARCH_V8R_CRC to make sure instructions enabled by
-march=armv8-r+crc are disassembled correctly.
Patch up some of the tests cases, see a brief explanation for each below.
inst.d:
This test checks the assembly & disassembly of basic instructions in armv3m. I
changed the expected behaviour for teqp, cmnp cmpp and testp instructions to
properly print p when disassembling, whereas before, in the 'unknown' case it
would disassemble these as UNPREDICTABLE as they were changed in later
architectures.
nops.d:
Was missing an -march, added one to make sure we were testing the right
behavior of NOP<c> instructions.
unpredictable.d:
Was missing an -march, added armv6 as that reproduced the behaviour being
tested.
This import name type is formally yet undocumented, but MSVC
produces/supports it, primarily for ARM64EC import libraries.
LLVM/LLD also supports this import name type. Since recently,
llvm-dlltool also uses this type for certain kinds of renamed imports
(that are easy to do in the long style import libraries produced by
GNU dlltool, but require this name type in short import libraries).
This name type contains a third string, in addition to the symbol
name and the DLL name, indicating the actual imported name to
reference in the import tables - which now can be distinct different
from the symbol name on the object file level.
8f23464a5d
and
7b275aa243
show how this import name type was added in LLVM.
Signed-off-by: Martin Storsjö <martin@martin.st>
Rewrite the inline documentation for the characters used in the `args'
member of `struct mips_opcode' to make it consistent in terms of style
and formatting. Discard references to inexistent macros.
Simplify assembly and disassembly of extended mnemonics with operands
with constant ORed bits:
Their instruction template already contains the respective constant
operand bits, as they are significant to distinguish the extended from
their base mnemonic. Operands are ORed into the instruction template.
Therefore it is not necessary to OR the constant bits into the operand
value during assembly in s390_insert_operand.
Additionally the constant operand bits from the instruction template
can be used to mask them from the operand value during disassembly in
s390_print_insn_with_opcode. For now do so for non-length unsigned
integer operands only.
The separate instruction formats need to be retained, as their masks
differ, which is relevant during disassembly to distinguish the base
and extended mnemonics from each other.
This affects the following extended mnemonics:
- vfaebs, vfaehs, vfaefs
- vfaezb, vfaezh, vfaezf
- vfaezbs, vfaezhs, vfaezfs
- vstrcbs, vstrchs, vstrcfs
- vstrczb, vstrczh, vstrczf
- vstrczbs, vstrczhs, vstrczfs
- wcefb, wcdgb
- wcelfb, wcdlgb
- wcfeb, wcgdb
- wclfeb, wclgdb
- wfisb, wfidb, wfixb
- wledb, wflrd, wflrx
include/
* opcode/s390.h (S390_OPERAND_OR1, S390_OPERAND_OR2,
S390_OPERAND_OR8): Remove.
opcodes/
* s390-opc.c (U4_OR1_24, U4_OR2_24, U4_OR8_28): Remove.
(INSTR_VRR_VVV0U1, INSTR_VRR_VVV0U2, INSTR_VRR_VVV0U3): Define
as INSTR_VRR_VVV0U0 while retaining respective insn fmt mask.
(INSTR_VRR_VV0UU8): Define as INSTR_VRR_VV0UU while retaining
respective insn fmt mask.
(INSTR_VRR_VVVU0VB1, INSTR_VRR_VVVU0VB2, INSTR_VRR_VVVU0VB3):
Define as INSTR_VRR_VVVU0VB while retaining respective insn fmt
mask.
* s390-dis.c (s390_print_insn_with_opcode): Mask constant
operand bits set in insn template of non-length unsigned
integer operands.
gas/
* config/tc-s390.c (s390_insert_operand): Do not OR constant
operand value bits.
Signed-off-by: Jens Remus <jremus@linux.ibm.com>
LoongArch: Add macros to get opcode and register of instructions appropriately
Currently, we get opcode of an instruction by manipulate the binary with
it's mask, it's a bit of a pain. Now a macro is defined to do this and a
macro to get the RD and RJ registers which is applicable to most instructions
of LoongArch are added.
This patch supports Zcmp instruction 'cm.mva01s' and 'cm.mvsa01'.
All disassemble instructions use the sreg format.
Co-Authored by: Charlie Keaney <charlie.keaney@embecosm.com>
Co-Authored by: Mary Bennett <mary.bennett@embecosm.com>
Co-Authored by: Nandni Jamnadas <nandni.jamnadas@embecosm.com>
Co-Authored by: Sinan Lin <sinan.lin@linux.alibaba.com>
Co-Authored by: Simon Cook <simon.cook@embecosm.com>
Co-Authored by: Shihua Liao <shihua@iscas.ac.cn>
Co-Authored by: Yulong Shi <yulong@iscas.ac.cn>
gas/ChangeLog:
PR 32036
* NEWS: Updated.
* config/tc-riscv.c (validate_riscv_insn): New operators.
(riscv_ip): Ditto.
* testsuite/gas/riscv/zcmp-mv.d: New test.
* testsuite/gas/riscv/zcmp-mv.s: New test.
include/ChangeLog:
PR 32036
* opcode/riscv-opc.h (MATCH_CM_MVA01S): New opcode.
(MASK_CM_MVA01S): New mask.
(MATCH_CM_MVSA01): New opcode.
(MASK_CM_MVSA01): New mask.
(DECLARE_INSN): New declarations.
* opcode/riscv.h (OP_MASK_SREG1): New mask.
(OP_SH_SREG1): New operand code.
(OP_MASK_SREG2): New mask.
(OP_SH_SREG2): New operand code.
(X_A0): New reg number.
(X_A1): Ditto.
(X_S7): Ditto.
(RISCV_SREG_0_7): New macro function.
opcodes/ChangeLog:
PR 32036
* riscv-dis.c (riscv_zcmp_get_sregno): New function.
(print_insn_args): New operators.
* riscv-opc.c (match_sreg1_not_eq_sreg2): New match function.
The recent change to detect duplicate enum values and return ECTF_DUPLICATE
when found turns out to perturb a great many callers. In particular, the
pahole-created kernel BTF has the same problem we historically did, and
gleefully emits duplicated enum constants in profusion. Handling the
resulting duplicate errors from BTF -> CTF converters reasonably is
unreasonably difficult (it amounts to forcing them to skip some types or
reimplement the deduplicator).
So let's step back a bit. What we care about mostly is that the
deduplicator treat enums with conflicting enumeration constants as
conflicting types: programs that want to look up enumeration constant ->
value mappings using the new APIs to do so might well want the same checks
to apply to any ctf_add_* operations they carry out (and since they're
*using* the new APIs, added at the same time as this restriction was
imposed, there is likely to be no negative consequence of this).
So we want some way to allow processes that know about duplicate detection
to opt into it, while allowing everyone else to stay clear of it: but we
want ctf_link to get this behaviour even if its caller has opted out.
So add a new concept to the API: dict-wide CTF flags, set via
ctf_dict_set_flag, obtained via ctf_dict_get_flag. They are not bitflags
but simple arbitrary integers and an on/off value, stored in an unspecified
manner (the one current flag, we translate into an LCTF_* flag value in the
internal ctf_dict ctf_flags word). If you pass in an invalid flag or value
you get a new ECTF_BADFLAG error, so the caller can easily tell whether
flags added in future are valid with a particular libctf or not.
We check this flag in ctf_add_enumerator, and set it around the link
(including on child per-CU dicts). The newish enumerator-iteration test is
souped up to check the semantics of the flag as well.
The fact that the flag can be set and unset at any time has curious
consequences. You can unset the flag, insert a pile of duplicates, then set
it and expect the new duplicates to be detected, not only by
ctf_add_enumerator but also by ctf_lookup_enumerator. This means we now
have to maintain the ctf_names and conflicting_enums enum-duplication
tracking as new enums are added, not purely as the dict is opened.
Move that code out of init_static_types_internal and into a new
ctf_track_enumerator function that addition can also call.
(None of this affects the file format or serialization machinery, which has
to be able to handle duplicate enumeration constants no matter what.)
include/
* ctf-api.h (CTF_ERRORS) [ECTF_BADFLAG]: New.
(ECTF_NERR): Update.
(CTF_STRICT_NO_DUP_ENUMERATORS): New flag.
(ctf_dict_set_flag): New function.
(ctf_dict_get_flag): Likewise.
libctf/
* ctf-impl.h (LCTF_STRICT_NO_DUP_ENUMERATORS): New flag.
(ctf_track_enumerator): Declare.
* ctf-dedup.c (ctf_dedup_emit_type): Set it.
* ctf-link.c (ctf_create_per_cu): Likewise.
(ctf_link_deduplicating_per_cu): Likewise.
(ctf_link): Likewise.
(ctf_link_write): Likewise.
* ctf-subr.c (ctf_dict_set_flag): New function.
(ctf_dict_get_flag): New function.
* ctf-open.c (init_static_types_internal): Move enum tracking to...
* ctf-create.c (ctf_track_enumerator): ... this new function.
(ctf_add_enumerator): Call it.
* libctf.ver: Add the new functions.
* testsuite/libctf-lookup/enumerator-iteration.c: Test them.
This erorr doesn't just indicate that there is no parent dictionary
(that's routine, and true of all dicts that are parents themselves)
but that a parent is *needed* but wasn't found.
include/
* ctf-api.h (_CTF_ERRORS) [ECTF_NOPARENT]: Improve error message.
ld/
* testsuite/ld-ctf/diag-parname.d: Adjust.
Add the MT ASE instruction operand types and encodings to the microMIPS
opcode table and enable the assembly of these instructions in GAS from
MIPSr2 onwards. Update the binutils and GAS testsuites accordingly.
References:
"MIPS Architecture for Programmers, Volume IV-f: The MIPS MT Module for
the microMIPS32 Architecture", MIPS Technologies, Inc., Document Number:
MD00768, Revision 1.12, July 16, 2013
Co-Authored-By: Maciej W. Rozycki <macro@redhat.com>
The semantics of the regular MIPS "+t" operand code is exactly the same
as that of the "E" operand code, so replace the former with the latter
in the single MFTC0 instruction with implicit 'sel' == 0 encoding where
it's used, matching the encoding with explicit 'sel' as well as other
instructions.
As from commit ab90248154 ("Add structures to describe MIPS
operands"), <https://sourceware.org/ml/binutils/2013-07/msg00135.html>,
the use of numerous regular MIPS and microMIPS OP_SH and OP_MASK macros
has been removed.
Similarly as from commit c3c0747817 ("Use operand structures for
MIPS16"), <https://sourceware.org/ml/binutils/2013-07/msg00136.html>,
the use of numerous MIPS16 OP_SH and OP_MASK macros has been removed.
And as from commit 9e12b7a2b0 ("Rewrite main mips_ip parsing loop"),
<https://sourceware.org/ml/binutils/2013-07/msg00139.html>, none of the
OP_OP macros are used anymore.
Discard all the unused macros then and only keep the small subset that
is still referred. This simplifies maintenance and removes the need to
keep the artificial arrangement where some regular MIPS and microMIPS
macros expand to 0 and are kept for compatibility with the opposite ISA
mode only, as it used to be required before the commit referred.
The "-t", "-u", "-v", and "-w" operand types refer 'rt' operand, which
is the target register rather than the source register. Additionally
the "-x" and "-y" R6 operand types refer 'rs' rather than 'rt' operand
of the BOVC/BNVC and the BEQC/BNEC instructions respectively. Also the
"-x" operand type does not permit 'rs' to be the same as 'rt'.
Correct inline documentation in opcode/mips.h accordingly.
Enforce some checks on the newly added subclass flags:
- If a subclass is set of one insn of an iclass, every insn of that
iclass must have non-zero subclass field.
- For all other iclasses, the subclass bits are zero for all insns.
include/
* opcode/aarch64.h (enum aarch64_insn_class): Identify the
maximum iclass enum value.
opcodes/
* aarch64-gen.c (iclass_has_subclasses_p): New array of bool.
(read_table): Enforce checks on subclass flags.
The existing iclass information tells us the general shape and purpose
of the instructions. In some cases, however, we need to further disect
the iclass on the basis of other finer-grain information. E.g., for the
purpose of SCFI, we need to know whether a given insn with iclass of
ldst_* is a load or a store. Similarly, whether a particular arithmetic
insn is an add or sub or mov, etc.
This patch defines new flags to demarcate the insns. Also provide an
access function for subclass lookup.
Later, we will enforce (in aarch64-gen.c) that if an iclass has at least
one instruction with a non-zero subclass, all instructions of the iclass
must have a non-zero subclass information. If none of the defined
subclasses are applicable (or not required for SCFI purposes),
F_SUBCLASS_OTHER can be used for such instructions.
include/
* opcode/aarch64.h (F_SUBCLASS): New flag.
(F_SUBCLASS_OTHER): Likewise.
(F_LDST_LOAD): Likewise.
(F_LDST_STORE): Likewise.
(F_ARITH_ADD): Likewise.
(F_ARITH_SUB): Likewise.
(F_ARITH_MOV): Likewise.
(F_BRANCH_CALL): Likewise.
(F_BRANCH_RET): Likewise.
(F_DP_TAG_ONLY): Likewise.
(aarch64_opcode_subclass_p): New definition.
This patch adds support for following sme2.1 zero instructions and
the spec is available here [1].
1. ZERO (single-vector).
2. ZERO (double-vector).
3. ZERO (quad-vector).
The VECTOR GROUP symbols VGx2 and VGx4 are optional for the assembler
for most of the sme and sve instructions. But for few of the sme2.1
zero instruction variants VECTOR GROUP symbols VGx2 and VGx4 are mandatory.
To address this a bit "F_VG_REQ" is introduced in this patch, on setting
F_VG_REQ bit in flags of aarch64_opcode forces the assembler to accept
instruction operand only having VECTOR GROUP symbols.
[1]: https://developer.arm.com/documentation/ddi0602/2024-03/SME-Instructions?lang=en
This patch adds support for following sme2.1 luti2 and luti4 instructions, spec is
available here [1]
1. LUTI2 (two registers) strided.
2. LUTI2 (four registers) strided.
3. LUTI4 (two registers) strided.
4. LUTI4 (four registers) strided.
[1]: https://developer.arm.com/documentation/ddi0602/2024-03/SME-Instructions?lang=en
This also amends the incorrect comment:
offset3 (intrepreted as FP = CFA + offset2)
If RA tracking is enabled, the offset to recover FP is at the third
index. The SFrame format (V2) has assumption that if FP is saved on
stack, RA must have been saved as well. This is true for the currently
supported arch Aarch64. For AMD64, RA tracking per SFrame FRE is not
necessary.
In future, when extending support for more architectures, this will
likely need to be revisited.
include/
* sframe.h: Make the comments clearer by enumerating what
happens per-ABI.
Add wrapper_symbol to bfd_link_hash_entry and set it to true for wrapper
symbol. Set wrap_status to wrapper if wrapper_symbol is true in LTO.
Note: Calling unwrap_hash_lookup to check for the wrapper symbol works
only when there is a definition for the wrapped symbol since references
to the wrapped symbol have been redirected to the wrapper symbol.
bfd/
PR ld/31956
* linker.c (bfd_wrapped_link_hash_lookup): Set wrapper_symbol
for wrapper symbol.
include/
PR ld/31956
* bfdlink.h (bfd_link_hash_entry): Add wrapper_symbol.
ld/
PR ld/31956
* plugin.c (get_symbols): Set wrap_status to wrapper if
wrapper_symbol is set.
* testsuite/ld-plugin/lto.exp: Run PR ld/31956 tests.
* testsuite/ld-plugin/pr31956a.c: New file.
* testsuite/ld-plugin/pr31956b.c: Likewise.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
This patch adds support for followign SVE2p1 instruction, spec is available here [1].
1. PMOV (to vector)
2. PMOV (to predicate)
Both pmov (to vector) and pmov (to predicate) have destination scalable vector
register and source scalable vector register respectively as an operand with no
suffix and optional index. To handle this case we have added 8 new operands in
this patch.
AARCH64_OPND_SVE_Zn0_INDEX, /* Zn[index], bits [9:5]. */
AARCH64_OPND_SVE_Zn1_17_INDEX, /* Zn[index], bits [9:5,17]. */
AARCH64_OPND_SVE_Zn2_18_INDEX, /* Zn[index], bits [9:5,18:17]. */
AARCH64_OPND_SVE_Zn3_22_INDEX, /* Zn[index], bits [9:5,18:17,22]. */
AARCH64_OPND_SVE_Zd0_INDEX, /* Zn[index], bits [4:0]. */
AARCH64_OPND_SVE_Zd1_17_INDEX, /* Zn[index], bits [4:0,17]. */
AARCH64_OPND_SVE_Zd2_18_INDEX, /* Zn[index], bits [4:0,18:17]. */
AARCH64_OPND_SVE_Zd3_22_INDEX, /* Zn[index], bits [4:0,18:17,22]. */
Since the index of the <Zd> operand is optional, the index part is
dropped in disassembly in both the cases of "no index" or "zero index".
As per spec: PMOV <Zd>{[<imm>]}, <Pn>.D
PMOV <Pn>.D, <Zd>{[<imm>]}
Example1:
Assembly: pmov z5[0], p6.d
Disassembly: pmov z5, p6.d
Assembly: pmov z5, p6.d
Disassembly: pmov z5, p6.d
Example2:
Assembly: pmov p4.b, z5[0]
Disassembly: pmov p4.b, z5
Assembly: pmov p4.b, z5
Disassembly: pmov p4.b, z5
[1]: https://developer.arm.com/documentation/ddi0602/2024-03/SVE-Instructions?lang=en
AArch64 defines new registers for the feature step2 (Enhanced Software Step
Extension). step2 is an Armv9.5-A feature.
This patch also adds relevant tests. Regression tested on aarch64-none-elf,
and no regression found.
AArch64 defines new registers for the feature spmu2 (System Performance
Monitors Extension version 2). spmu2 is an Armv9.5-A feature.
This patch also adds relevant tests. Regression tested on aarch64-none-elf,
and no regression found.
AArch64 defines new registers for the feature e3dse (Delegated SError
exceptions for EL3): vdisr_el3 and vdisr_el3. e3dse is an Armv9.5-A
feature.
This patch also adds relevant tests. Regression tested on aarch64-none-elf,
and no regression found.
The new -march=armv9.5-a flag enables access to the
mandatory cpa, lut and faminmax extensions.
Existing test cases for features are extended to verify they
work without additional flags.
This patch update the cas instruction in Zabha extension [1],
when both Zabha and Zacas extension enabled.
[1] https://github.com/riscv/riscv-zabha/tags
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): New extension case.
gas/ChangeLog:
* testsuite/gas/riscv/zabha-32.d: New instructions.
* testsuite/gas/riscv/zabha.d: Ditto.
* testsuite/gas/riscv/zabha.s: Ditto.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_AMOCAS_B): New opcodes.
(MASK_AMOCAS_B): Ditto.
(MATCH_AMOCAS_H): Ditto.
(MASK_AMOCAS_H): Ditto.
(DECLARE_INSN): New instructions.
* opcode/riscv.h (enum riscv_insn_class): New class case.
opcodes/ChangeLog:
* riscv-opc.c: New instructions.
This patch fixes encoding and syntax for sve2p1 instructions ld[1-4]q/st[1-4]q
as mentioned below, for the issues reported here.
https://sourceware.org/pipermail/binutils/2024-February/132408.html
1) Previously all the ld[1-4]q/st[1-4]q instructions are wrongly added as
predicated instructions and this issue is fixed in this patch by replacing
"SVE2p1_INSNC" with "SVE2p1_INSN" macro.
2) Wrong first operand in all the ld[1-4]q/st[1-4]q instructions is fixed
by replacing "SVE_Zt" with "SVE_ZtxN".
3) Wrong operand qualifiers in ld1q and st1q instructions are also fixed in
this patch.
4) In ld1q/st1q the index in the second argument is optional and if index
is xzr and is skipped in the assembly, the index field is ignored by the
disassembler.
Fixing above mentioned issues helps with following:
1) ld1q and st1q first register operand accepts enclosed figure braces.
2) ld2q, ld3q, ld4q, st2q, st3q, and st4q instructions accepts wrapping
sequence of vector registers.
For the instructions ld[2-4]q/st[2-4]q, tests for wrapping sequence of vector
registers are added along with short-form of operands for non-wrapping sequence.
I have added test using following logic:
ld2q {Z0.Q, Z1.Q}, p0/Z, [x0, #0, MUL VL] //raw insn encoding (all zeroes)
ld2q {Z31.Q, Z0.Q}, p0/Z, [x0, #0, MUL VL] // encoding of <Zt1>
ld2q {Z0.Q, Z1.Q}, p7/Z, [x0, #0, MUL VL] // encoding of <Pg>
ld2q {Z0.Q, Z1.Q}, p0/Z, [x30, #0, MUL VL] // encoding of <Xm>
ld2q {Z0.Q, Z1.Q}, p0/Z, [x0, #-16, MUL VL] // encoding of <imm> (low value)
ld2q {Z0.Q, Z1.Q}, p0/Z, [x0, #14, MUL VL] // encoding of <imm> (high value)
ld2q {Z31.Q, Z0.Q}, p7/Z, [x30, #-16, MUL VL] // encoding of all fields (all ones)
ld2q {Z30.Q, Z31.Q}, p1/Z, [x3, #-2, MUL VL] // random encoding.
For all the above form of instructions the hyphenated form is preferred for
disassembly if there are more than two registers in the list, and the register
numbers are monotonically increasing in increments of one.
This patch fixes the syntax of sve2p1 "extq" instruction by modifying the operands
count to 4. A new operand AARCH64_OPND_SVE_UIMM4 is defined to handle the 4th
argument an 4-bit unsigned immediate of extq instruction. The instruction encoding
is updated to use constraint C_SCAN_MOVPRFX, to enable "extq" instruction to immediately
precede in program order by a MOVPRFX instruction. Also removed the unused operand
AARCH64_OPND_SVE_Zm_imm4.
This issues was reported here:
https://sourceware.org/pipermail/binutils/2024-February/132408.html
This patch fixes the syntax of sve2p1 "dupq" instruction by modifying the way
2nd operand does the encoding and decoding using the [<imm>] value.
dupq makes use of already existing aarch64_ins_sve_index and aarch64_ext_sve_index
inserter and extractor functions. The definitions of aarch64_ins_sve_index_imm (inserter)
and aarch64_ext_sve_index_imm (extractor) is removed in this patch.
This issues was reported here:
https://sourceware.org/pipermail/binutils/2024-February/132408.html
LoongArch defines hardware watchpoint functions for fetch operations.
After the software configures the watchpoints for fetch, the processor
hardware will monitor the access addresses of the fetch operations and
trigger a watchpoint exception when the watchpoint setting conditions
are met.
Hardware watchpoints for fetch operations is used to implement hardware
breakpoint function on LoongArch. Refer to the following document for
hardware breakpoint.
https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#control-and-status-registers-related-to-watchpoints
A simple test is as follows:
lihui@bogon:~$ cat test.c
#include <stdio.h>
int a = 0;
int main()
{
printf("start test\n");
a = 1;
printf("a = %d\n", a);
printf("end test\n");
return 0;
}
lihui@bogon:~$ gcc -g test.c -o test
without this patch:
lihui@bogon:~$ gdb test
...
(gdb) start
...
Temporary breakpoint 1, main () at test.c:5
5 printf("start test\n");
(gdb) hbreak 8
No hardware breakpoint support in the target.
with this patch:
lihui@bogon:~$ gdb test
...
(gdb) start
...
Temporary breakpoint 1, main () at test.c:5
5 printf("start test\n");
(gdb) hbreak 8
Hardware assisted breakpoint 2 at 0x1200006ec: file test.c, line 8.
(gdb) c
Continuing.
start test
a = 1
Breakpoint 2, main () at test.c:8
8 printf("end test\n");
(gdb) c
Continuing.
end test
[Inferior 1 (process 25378) exited normally]
Signed-off-by: Hui Li <lihui@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
LoongArch defines hardware watchpoint functions for load/store
operations. After the software configures the watchpoints for
load/store, the processor hardware will monitor the access
addresses of the load/store operations and trigger watchpoint
exception when the watchpoint setting conditions are met.
After this patch, watch/rwatch/awatch command are supported. Refer to the
following document for hardware watchpoint.
https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#control-and-status-registers-related-to-watchpoints
A simple test is as follows:
lihui@bogon:~$ cat test.c
#include <stdio.h>
int a = 0;
int main()
{
printf("start test\n");
a = 1;
printf("a = %d\n", a);
printf("end test\n");
return 0;
}
lihui@bogon:~$ gcc -g test.c -o test
without this patch:
lihui@bogon:~$ gdb test
...
(gdb) start
...
Temporary breakpoint 1, main () at test.c:5
5 printf("start test\n");
(gdb) awatch a
Target does not support this type of hardware watchpoint.
...
with this patch:
lihui@bogon:~$ gdb test
...
(gdb) start
...
Temporary breakpoint 1, main () at test.c:5
5 printf("start test\n");
(gdb) awatch a
Hardware access (read/write) watchpoint 2: a
(gdb) c
Continuing.
start test
Hardware access (read/write) watchpoint 2: a
Old value = 0
New value = 1
main () at test.c:7
7 printf("a = %d\n", a);
(gdb) c
Continuing.
Hardware access (read/write) watchpoint 2: a
Value = 1
0x00000001200006e0 in main () at test.c:7
7 printf("a = %d\n", a);
(gdb) c
Continuing.
a = 1
end test
[Inferior 1 (process 22250) exited normally]
Signed-off-by: Hui Li <lihui@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
This includes:
- FEAT_SME_F8F32 (+sme-f8f32)
- FEAT_SME_F8F16 (+sme-f8f16)
The FP16 addition/subtraction instructions originally added by
FEAT_SME_F16F16 haven't been added to Binutils yet. They are also
required to be enabled if FEAT_SME_F8F16 is present, so they are
included in this patch.
This includes all the instructions under the following features:
- FEAT_FP8FMA (+fp8fma)
- FEAT_FP8DOT4 (+fp8dot4)
- FEAT_FP8DOT2 (+fp8dot2)
- FEAT_SSVE_FP8FMA (+ssve-fp8fma)
- FEAT_SSVE_FP8DOT4 (+ssve-fp8dot4)
- FEAT_SSVE_FP8DOT2 (+ssve-fp8dot2)
Introduces instructions for the SME2 lutv2 extension for AArch64. They
are documented in the following document:
* ARM DDI0602
For both luti4 instructions, we introduced an operand called
SME_Znx2_BIT_INDEX. We use the existing function parse_vector_reg_list
for parsing but modified that function so that it can accept operands
without qualifiers and rejects instructions that have operands with
qualifiers but are not supposed to have operands with qualifiers.
For disassembly, we modified print_register_list so that it could
accept register lists without qualifiers.
For one luti4 instruction, we introduced a SME_Zdnx4_STRIDED. It is
similar to SME_Ztx4_STRIDED and we could use existing code for parsing,
encoding, and disassembly.
For movt instruction, we introduced an operand called SME_ZT0_INDEX2_12.
This is a ZT0 register with a bit index encoded in [13:12]. It is
similar to SME_ZT0_INDEX.
We also introduced an iclass named sme_size_12_b so that we can encode
size bits [13:12] correctly when only 'b' is allowed as qualifier.
Three new functions for looking up the enum type containing a given
enumeration constant, and optionally that constant's value.
The simplest, ctf_lookup_enumerator, looks up a root-visible enumerator by
name in one dict: if the dict contains multiple such constants (which is
possible for dicts created by older versions of the libctf deduplicator),
ECTF_DUPLICATE is returned.
The next simplest, ctf_lookup_enumerator_next, is an iterator which returns
all enumerators with a given name in a given dict, whether root-visible or
not.
The most elaborate, ctf_arc_lookup_enumerator_next, finds all
enumerators with a given name across all dicts in an entire CTF archive,
whether root-visible or not, starting looking in the shared parent dict;
opened dicts are cached (as with all other ctf_arc_*lookup functions) so
that repeated use does not incur repeated opening costs.
All three of these return enumerator values as int64_t: unfortunately, API
compatibility concerns prevent us from doing the same with the other older
enum-related functions, which all return enumerator constant values as ints.
We may be forced to add symbol-versioning compatibility aliases that fix the
other functions in due course, bumping the soname for platforms that do not
support such things.
ctf_arc_lookup_enumerator_next is implemented as a nested ctf_archive_next
iterator, and inside that, a nested ctf_lookup_enumerator_next iterator
within each dict. To aid in this, add support to ctf_next_t iterators for
iterators that are implemented in terms of two simultaneous nested iterators
at once. (It has always been possible for callers to use as many nested or
semi-overlapping ctf_next_t iterators as they need, which is one of the
advantages of this style over the _iter style that calls a function for each
thing iterated over: the iterator change here permits *ctf_next_t iterators
themselves* to be implemented by iterating using multiple other iterators as
part of their internal operation, transparently to the caller.)
Also add a testcase that tests all these functions (which is fairly easy
because ctf_arc_lookup_enumerator_next is implemented in terms of
ctf_lookup_enumerator_next) in addition to enumeration addition in
ctf_open()ed dicts, ctf_add_enumerator duplicate enumerator addition, and
conflicting enumerator constant deduplication.
include/
* ctf-api.h (ctf_lookup_enumerator): New.
(ctf_lookup_enumerator_next): Likewise.
(ctf_arc_lookup_enumerator_next): Likewise.
libctf/
* libctf.ver: Add them.
* ctf-impl.h (ctf_next_t) <ctn_next_inner>: New.
* ctf-util.c (ctf_next_copy): Copy it.
(ctf_next_destroy): Destroy it.
* ctf-lookup.c (ctf_lookup_enumerator): New.
(ctf_lookup_enumerator_next): New.
* ctf-archive.c (ctf_arc_lookup_enumerator_next): New.
* testsuite/libctf-lookup/enumerator-iteration.*: New test.
* testsuite/libctf-lookup/enum-ctf-2.c: New test CTF, used by the
above.
