mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-03 09:04:21 +08:00
a271bf3241
Following the introduction of bridge_atomic_enable in the ingenic drm driver, the crtc is enabled between .prepare and .enable, if it exists. Add it so the backlight is only enabled after the crtc is, to avoid graphical issues. As we're moving the "sleep out" command out of the init sequence into .enable for the ABT, we need to switch the regmap cache to REGCACHE_FLAT to be able to use regmap_set_bits, given this panel registers are write-ony and read as 0. Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com> Signed-off-by: Paul Cercueil <paul@crapouillou.net> [pcercuei: Remove empty line after opening brace] Acked-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220321133651.291592-4-cbranchereau@gmail.com
384 lines
9.7 KiB
C
384 lines
9.7 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Asia Better Technology Ltd. Y030XX067A IPS LCD panel driver
|
|
*
|
|
* Copyright (C) 2020, Paul Cercueil <paul@crapouillou.net>
|
|
* Copyright (C) 2020, Christophe Branchereau <cbranchereau@gmail.com>
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/device.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/media-bus-format.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/spi/spi.h>
|
|
|
|
#include <drm/drm_modes.h>
|
|
#include <drm/drm_panel.h>
|
|
|
|
#define REG00_VBRT_CTRL(val) (val)
|
|
|
|
#define REG01_COM_DC(val) (val)
|
|
|
|
#define REG02_DA_CONTRAST(val) (val)
|
|
#define REG02_VESA_SEL(val) ((val) << 5)
|
|
#define REG02_COMDC_SW BIT(7)
|
|
|
|
#define REG03_VPOSITION(val) (val)
|
|
#define REG03_BSMOUNT BIT(5)
|
|
#define REG03_COMTST BIT(6)
|
|
#define REG03_HPOSITION1 BIT(7)
|
|
|
|
#define REG04_HPOSITION1(val) (val)
|
|
|
|
#define REG05_CLIP BIT(0)
|
|
#define REG05_NVM_VREFRESH BIT(1)
|
|
#define REG05_SLFR BIT(2)
|
|
#define REG05_SLBRCHARGE(val) ((val) << 3)
|
|
#define REG05_PRECHARGE_LEVEL(val) ((val) << 6)
|
|
|
|
#define REG06_TEST5 BIT(0)
|
|
#define REG06_SLDWN BIT(1)
|
|
#define REG06_SLRGT BIT(2)
|
|
#define REG06_TEST2 BIT(3)
|
|
#define REG06_XPSAVE BIT(4)
|
|
#define REG06_GAMMA_SEL(val) ((val) << 5)
|
|
#define REG06_NT BIT(7)
|
|
|
|
#define REG07_TEST1 BIT(0)
|
|
#define REG07_HDVD_POL BIT(1)
|
|
#define REG07_CK_POL BIT(2)
|
|
#define REG07_TEST3 BIT(3)
|
|
#define REG07_TEST4 BIT(4)
|
|
#define REG07_480_LINEMASK BIT(5)
|
|
#define REG07_AMPTST(val) ((val) << 6)
|
|
|
|
#define REG08_SLHRC(val) (val)
|
|
#define REG08_CLOCK_DIV(val) ((val) << 2)
|
|
#define REG08_PANEL(val) ((val) << 5)
|
|
|
|
#define REG09_SUB_BRIGHT_R(val) (val)
|
|
#define REG09_NW_NB BIT(6)
|
|
#define REG09_IPCON BIT(7)
|
|
|
|
#define REG0A_SUB_BRIGHT_B(val) (val)
|
|
#define REG0A_PAIR BIT(6)
|
|
#define REG0A_DE_SEL BIT(7)
|
|
|
|
#define REG0B_MBK_POSITION(val) (val)
|
|
#define REG0B_HD_FREERUN BIT(4)
|
|
#define REG0B_VD_FREERUN BIT(5)
|
|
#define REG0B_YUV2BIN(val) ((val) << 6)
|
|
|
|
#define REG0C_CONTRAST_R(val) (val)
|
|
#define REG0C_DOUBLEREAD BIT(7)
|
|
|
|
#define REG0D_CONTRAST_G(val) (val)
|
|
#define REG0D_RGB_YUV BIT(7)
|
|
|
|
#define REG0E_CONTRAST_B(val) (val)
|
|
#define REG0E_PIXELCOLORDRIVE BIT(7)
|
|
|
|
#define REG0F_ASPECT BIT(0)
|
|
#define REG0F_OVERSCAN(val) ((val) << 1)
|
|
#define REG0F_FRAMEWIDTH(val) ((val) << 3)
|
|
|
|
#define REG10_BRIGHT(val) (val)
|
|
|
|
#define REG11_SIG_GAIN(val) (val)
|
|
#define REG11_SIGC_CNTL BIT(6)
|
|
#define REG11_SIGC_POL BIT(7)
|
|
|
|
#define REG12_COLOR(val) (val)
|
|
#define REG12_PWCKSEL(val) ((val) << 6)
|
|
|
|
#define REG13_4096LEVEL_CNTL(val) (val)
|
|
#define REG13_SL4096(val) ((val) << 4)
|
|
#define REG13_LIMITER_CONTROL BIT(7)
|
|
|
|
#define REG14_PANEL_TEST(val) (val)
|
|
|
|
#define REG15_NVM_LINK0 BIT(0)
|
|
#define REG15_NVM_LINK1 BIT(1)
|
|
#define REG15_NVM_LINK2 BIT(2)
|
|
#define REG15_NVM_LINK3 BIT(3)
|
|
#define REG15_NVM_LINK4 BIT(4)
|
|
#define REG15_NVM_LINK5 BIT(5)
|
|
#define REG15_NVM_LINK6 BIT(6)
|
|
#define REG15_NVM_LINK7 BIT(7)
|
|
|
|
struct y030xx067a_info {
|
|
const struct drm_display_mode *display_modes;
|
|
unsigned int num_modes;
|
|
u16 width_mm, height_mm;
|
|
u32 bus_format, bus_flags;
|
|
};
|
|
|
|
struct y030xx067a {
|
|
struct drm_panel panel;
|
|
struct spi_device *spi;
|
|
struct regmap *map;
|
|
|
|
const struct y030xx067a_info *panel_info;
|
|
|
|
struct regulator *supply;
|
|
struct gpio_desc *reset_gpio;
|
|
};
|
|
|
|
static inline struct y030xx067a *to_y030xx067a(struct drm_panel *panel)
|
|
{
|
|
return container_of(panel, struct y030xx067a, panel);
|
|
}
|
|
|
|
static const struct reg_sequence y030xx067a_init_sequence[] = {
|
|
{ 0x00, REG00_VBRT_CTRL(0x7f) },
|
|
{ 0x01, REG01_COM_DC(0x3c) },
|
|
{ 0x02, REG02_VESA_SEL(0x3) | REG02_DA_CONTRAST(0x1f) },
|
|
{ 0x03, REG03_VPOSITION(0x0a) },
|
|
{ 0x04, REG04_HPOSITION1(0xd2) },
|
|
{ 0x05, REG05_CLIP | REG05_NVM_VREFRESH | REG05_SLBRCHARGE(0x2) },
|
|
{ 0x06, REG06_NT },
|
|
{ 0x07, 0 },
|
|
{ 0x08, REG08_PANEL(0x1) | REG08_CLOCK_DIV(0x2) },
|
|
{ 0x09, REG09_SUB_BRIGHT_R(0x20) },
|
|
{ 0x0a, REG0A_SUB_BRIGHT_B(0x20) },
|
|
{ 0x0b, REG0B_HD_FREERUN | REG0B_VD_FREERUN },
|
|
{ 0x0c, REG0C_CONTRAST_R(0x00) },
|
|
{ 0x0d, REG0D_CONTRAST_G(0x00) },
|
|
{ 0x0e, REG0E_CONTRAST_B(0x10) },
|
|
{ 0x0f, 0 },
|
|
{ 0x10, REG10_BRIGHT(0x7f) },
|
|
{ 0x11, REG11_SIGC_CNTL | REG11_SIG_GAIN(0x3f) },
|
|
{ 0x12, REG12_COLOR(0x20) | REG12_PWCKSEL(0x1) },
|
|
{ 0x13, REG13_4096LEVEL_CNTL(0x8) },
|
|
{ 0x14, 0 },
|
|
{ 0x15, 0 },
|
|
};
|
|
|
|
static int y030xx067a_prepare(struct drm_panel *panel)
|
|
{
|
|
struct y030xx067a *priv = to_y030xx067a(panel);
|
|
struct device *dev = &priv->spi->dev;
|
|
int err;
|
|
|
|
err = regulator_enable(priv->supply);
|
|
if (err) {
|
|
dev_err(dev, "Failed to enable power supply: %d\n", err);
|
|
return err;
|
|
}
|
|
|
|
/* Reset the chip */
|
|
gpiod_set_value_cansleep(priv->reset_gpio, 1);
|
|
usleep_range(1000, 20000);
|
|
gpiod_set_value_cansleep(priv->reset_gpio, 0);
|
|
usleep_range(1000, 20000);
|
|
|
|
err = regmap_multi_reg_write(priv->map, y030xx067a_init_sequence,
|
|
ARRAY_SIZE(y030xx067a_init_sequence));
|
|
if (err) {
|
|
dev_err(dev, "Failed to init registers: %d\n", err);
|
|
goto err_disable_regulator;
|
|
}
|
|
|
|
return 0;
|
|
|
|
err_disable_regulator:
|
|
regulator_disable(priv->supply);
|
|
return err;
|
|
}
|
|
|
|
static int y030xx067a_unprepare(struct drm_panel *panel)
|
|
{
|
|
struct y030xx067a *priv = to_y030xx067a(panel);
|
|
|
|
gpiod_set_value_cansleep(priv->reset_gpio, 1);
|
|
regulator_disable(priv->supply);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int y030xx067a_enable(struct drm_panel *panel)
|
|
{
|
|
struct y030xx067a *priv = to_y030xx067a(panel);
|
|
|
|
regmap_set_bits(priv->map, 0x06, REG06_XPSAVE);
|
|
|
|
if (panel->backlight) {
|
|
/* Wait for the picture to be ready before enabling backlight */
|
|
msleep(120);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int y030xx067a_disable(struct drm_panel *panel)
|
|
{
|
|
struct y030xx067a *priv = to_y030xx067a(panel);
|
|
|
|
regmap_clear_bits(priv->map, 0x06, REG06_XPSAVE);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int y030xx067a_get_modes(struct drm_panel *panel,
|
|
struct drm_connector *connector)
|
|
{
|
|
struct y030xx067a *priv = to_y030xx067a(panel);
|
|
const struct y030xx067a_info *panel_info = priv->panel_info;
|
|
struct drm_display_mode *mode;
|
|
unsigned int i;
|
|
|
|
for (i = 0; i < panel_info->num_modes; i++) {
|
|
mode = drm_mode_duplicate(connector->dev,
|
|
&panel_info->display_modes[i]);
|
|
if (!mode)
|
|
return -ENOMEM;
|
|
|
|
drm_mode_set_name(mode);
|
|
|
|
mode->type = DRM_MODE_TYPE_DRIVER;
|
|
if (panel_info->num_modes == 1)
|
|
mode->type |= DRM_MODE_TYPE_PREFERRED;
|
|
|
|
drm_mode_probed_add(connector, mode);
|
|
}
|
|
|
|
connector->display_info.bpc = 8;
|
|
connector->display_info.width_mm = panel_info->width_mm;
|
|
connector->display_info.height_mm = panel_info->height_mm;
|
|
|
|
drm_display_info_set_bus_formats(&connector->display_info,
|
|
&panel_info->bus_format, 1);
|
|
connector->display_info.bus_flags = panel_info->bus_flags;
|
|
|
|
return panel_info->num_modes;
|
|
}
|
|
|
|
static const struct drm_panel_funcs y030xx067a_funcs = {
|
|
.prepare = y030xx067a_prepare,
|
|
.unprepare = y030xx067a_unprepare,
|
|
.enable = y030xx067a_enable,
|
|
.disable = y030xx067a_disable,
|
|
.get_modes = y030xx067a_get_modes,
|
|
};
|
|
|
|
static const struct regmap_config y030xx067a_regmap_config = {
|
|
.reg_bits = 8,
|
|
.val_bits = 8,
|
|
.max_register = 0x15,
|
|
.cache_type = REGCACHE_FLAT,
|
|
};
|
|
|
|
static int y030xx067a_probe(struct spi_device *spi)
|
|
{
|
|
struct device *dev = &spi->dev;
|
|
struct y030xx067a *priv;
|
|
int err;
|
|
|
|
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
|
if (!priv)
|
|
return -ENOMEM;
|
|
|
|
priv->spi = spi;
|
|
spi_set_drvdata(spi, priv);
|
|
|
|
priv->map = devm_regmap_init_spi(spi, &y030xx067a_regmap_config);
|
|
if (IS_ERR(priv->map)) {
|
|
dev_err(dev, "Unable to init regmap\n");
|
|
return PTR_ERR(priv->map);
|
|
}
|
|
|
|
priv->panel_info = of_device_get_match_data(dev);
|
|
if (!priv->panel_info)
|
|
return -EINVAL;
|
|
|
|
priv->supply = devm_regulator_get(dev, "power");
|
|
if (IS_ERR(priv->supply))
|
|
return dev_err_probe(dev, PTR_ERR(priv->supply),
|
|
"Failed to get power supply\n");
|
|
|
|
priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
|
|
if (IS_ERR(priv->reset_gpio))
|
|
return dev_err_probe(dev, PTR_ERR(priv->reset_gpio),
|
|
"Failed to get reset GPIO\n");
|
|
|
|
drm_panel_init(&priv->panel, dev, &y030xx067a_funcs,
|
|
DRM_MODE_CONNECTOR_DPI);
|
|
|
|
err = drm_panel_of_backlight(&priv->panel);
|
|
if (err)
|
|
return err;
|
|
|
|
drm_panel_add(&priv->panel);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void y030xx067a_remove(struct spi_device *spi)
|
|
{
|
|
struct y030xx067a *priv = spi_get_drvdata(spi);
|
|
|
|
drm_panel_remove(&priv->panel);
|
|
drm_panel_disable(&priv->panel);
|
|
drm_panel_unprepare(&priv->panel);
|
|
}
|
|
|
|
static const struct drm_display_mode y030xx067a_modes[] = {
|
|
{ /* 60 Hz */
|
|
.clock = 14400,
|
|
.hdisplay = 320,
|
|
.hsync_start = 320 + 10,
|
|
.hsync_end = 320 + 10 + 37,
|
|
.htotal = 320 + 10 + 37 + 33,
|
|
.vdisplay = 480,
|
|
.vsync_start = 480 + 84,
|
|
.vsync_end = 480 + 84 + 20,
|
|
.vtotal = 480 + 84 + 20 + 16,
|
|
.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
|
|
},
|
|
{ /* 50 Hz */
|
|
.clock = 12000,
|
|
.hdisplay = 320,
|
|
.hsync_start = 320 + 10,
|
|
.hsync_end = 320 + 10 + 37,
|
|
.htotal = 320 + 10 + 37 + 33,
|
|
.vdisplay = 480,
|
|
.vsync_start = 480 + 84,
|
|
.vsync_end = 480 + 84 + 20,
|
|
.vtotal = 480 + 84 + 20 + 16,
|
|
.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
|
|
},
|
|
};
|
|
|
|
static const struct y030xx067a_info y030xx067a_info = {
|
|
.display_modes = y030xx067a_modes,
|
|
.num_modes = ARRAY_SIZE(y030xx067a_modes),
|
|
.width_mm = 69,
|
|
.height_mm = 51,
|
|
.bus_format = MEDIA_BUS_FMT_RGB888_3X8_DELTA,
|
|
.bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE | DRM_BUS_FLAG_DE_LOW,
|
|
};
|
|
|
|
static const struct of_device_id y030xx067a_of_match[] = {
|
|
{ .compatible = "abt,y030xx067a", .data = &y030xx067a_info },
|
|
{ /* sentinel */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, y030xx067a_of_match);
|
|
|
|
static struct spi_driver y030xx067a_driver = {
|
|
.driver = {
|
|
.name = "abt-y030xx067a",
|
|
.of_match_table = y030xx067a_of_match,
|
|
},
|
|
.probe = y030xx067a_probe,
|
|
.remove = y030xx067a_remove,
|
|
};
|
|
module_spi_driver(y030xx067a_driver);
|
|
|
|
MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
|
|
MODULE_AUTHOR("Christophe Branchereau <cbranchereau@gmail.com>");
|
|
MODULE_LICENSE("GPL v2");
|