mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-18 09:44:18 +08:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
57 lines
2.6 KiB
Plaintext
57 lines
2.6 KiB
Plaintext
Hollis Blanchard <hollis@austin.ibm.com>
|
|
5 Jun 2002
|
|
|
|
This document describes the system (including self-modifying code) used in the
|
|
PPC Linux kernel to support a variety of PowerPC CPUs without requiring
|
|
compile-time selection.
|
|
|
|
Early in the boot process the ppc32 kernel detects the current CPU type and
|
|
chooses a set of features accordingly. Some examples include Altivec support,
|
|
split instruction and data caches, and if the CPU supports the DOZE and NAP
|
|
sleep modes.
|
|
|
|
Detection of the feature set is simple. A list of processors can be found in
|
|
arch/ppc/kernel/cputable.c. The PVR register is masked and compared with each
|
|
value in the list. If a match is found, the cpu_features of cur_cpu_spec is
|
|
assigned to the feature bitmask for this processor and a __setup_cpu function
|
|
is called.
|
|
|
|
C code may test 'cur_cpu_spec[smp_processor_id()]->cpu_features' for a
|
|
particular feature bit. This is done in quite a few places, for example
|
|
in ppc_setup_l2cr().
|
|
|
|
Implementing cpufeatures in assembly is a little more involved. There are
|
|
several paths that are performance-critical and would suffer if an array
|
|
index, structure dereference, and conditional branch were added. To avoid the
|
|
performance penalty but still allow for runtime (rather than compile-time) CPU
|
|
selection, unused code is replaced by 'nop' instructions. This nop'ing is
|
|
based on CPU 0's capabilities, so a multi-processor system with non-identical
|
|
processors will not work (but such a system would likely have other problems
|
|
anyways).
|
|
|
|
After detecting the processor type, the kernel patches out sections of code
|
|
that shouldn't be used by writing nop's over it. Using cpufeatures requires
|
|
just 2 macros (found in include/asm-ppc/cputable.h), as seen in head.S
|
|
transfer_to_handler:
|
|
|
|
#ifdef CONFIG_ALTIVEC
|
|
BEGIN_FTR_SECTION
|
|
mfspr r22,SPRN_VRSAVE /* if G4, save vrsave register value */
|
|
stw r22,THREAD_VRSAVE(r23)
|
|
END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
|
|
#endif /* CONFIG_ALTIVEC */
|
|
|
|
If CPU 0 supports Altivec, the code is left untouched. If it doesn't, both
|
|
instructions are replaced with nop's.
|
|
|
|
The END_FTR_SECTION macro has two simpler variations: END_FTR_SECTION_IFSET
|
|
and END_FTR_SECTION_IFCLR. These simply test if a flag is set (in
|
|
cur_cpu_spec[0]->cpu_features) or is cleared, respectively. These two macros
|
|
should be used in the majority of cases.
|
|
|
|
The END_FTR_SECTION macros are implemented by storing information about this
|
|
code in the '__ftr_fixup' ELF section. When do_cpu_ftr_fixups
|
|
(arch/ppc/kernel/misc.S) is invoked, it will iterate over the records in
|
|
__ftr_fixup, and if the required feature is not present it will loop writing
|
|
nop's from each BEGIN_FTR_SECTION to END_FTR_SECTION.
|