linux/Documentation/kbuild/modules.txt

Building External Modules

This document describes how to build an out-of-tree kernel module.

=== Table of Contents

	=== 1 Introduction
	=== 2 How to Build External Modules
	   --- 2.1 Command Syntax
	   --- 2.2 Options
	   --- 2.3 Targets
	   --- 2.4 Building Separate Files
	=== 3. Creating a Kbuild File for an External Module
	   --- 3.1 Shared Makefile
	   --- 3.2 Separate Kbuild file and Makefile
	   --- 3.3 Binary Blobs
	   --- 3.4 Building Multiple Modules
	=== 4. Include Files
	   --- 4.1 Kernel Includes
	   --- 4.2 Single Subdirectory
	   --- 4.3 Several Subdirectories
	=== 5. Module Installation
	   --- 5.1 INSTALL_MOD_PATH
	   --- 5.2 INSTALL_MOD_DIR
	=== 6. Module Versioning
	   --- 6.1 Symbols From the Kernel (vmlinux + modules)
	   --- 6.2 Symbols and External Modules
	   --- 6.3 Symbols From Another External Module
	=== 7. Tips & Tricks
	   --- 7.1 Testing for CONFIG_FOO_BAR



=== 1. Introduction

"kbuild" is the build system used by the Linux kernel. Modules must use
kbuild to stay compatible with changes in the build infrastructure and
to pick up the right flags to "gcc." Functionality for building modules
both in-tree and out-of-tree is provided. The method for building
either is similar, and all modules are initially developed and built
out-of-tree.

Covered in this document is information aimed at developers interested
in building out-of-tree (or "external") modules. The author of an
external module should supply a makefile that hides most of the
complexity, so one only has to type "make" to build the module. This is
easily accomplished, and a complete example will be presented in
section 3.


=== 2. How to Build External Modules

To build external modules, you must have a prebuilt kernel available
that contains the configuration and header files used in the build.
Also, the kernel must have been built with modules enabled. If you are
using a distribution kernel, there will be a package for the kernel you
are running provided by your distribution.

An alternative is to use the "make" target "modules_prepare." This will
make sure the kernel contains the information required. The target
exists solely as a simple way to prepare a kernel source tree for
building external modules.

NOTE: "modules_prepare" will not build Module.symvers even if
CONFIG_MODVERSIONS is set; therefore, a full kernel build needs to be
executed to make module versioning work.

--- 2.1 Command Syntax

	The command to build an external module is:

		$ make -C <path_to_kernel_src> M=$PWD

	The kbuild system knows that an external module is being built
	due to the "M=<dir>" option given in the command.

	To build against the running kernel use:

		$ make -C /lib/modules/`uname -r`/build M=$PWD

	Then to install the module(s) just built, add the target
	"modules_install" to the command:

		$ make -C /lib/modules/`uname -r`/build M=$PWD modules_install

--- 2.2 Options

	($KDIR refers to the path of the kernel source directory.)

	make -C $KDIR M=$PWD

	-C $KDIR
		The directory where the kernel source is located.
		"make" will actually change to the specified directory
		when executing and will change back when finished.

	M=$PWD
		Informs kbuild that an external module is being built.
		The value given to "M" is the absolute path of the
		directory where the external module (kbuild file) is
		located.

--- 2.3 Targets

	When building an external module, only a subset of the "make"
	targets are available.

	make -C $KDIR M=$PWD [target]

	The default will build the module(s) located in the current
	directory, so a target does not need to be specified. All
	output files will also be generated in this directory. No
	attempts are made to update the kernel source, and it is a
	precondition that a successful "make" has been executed for the
	kernel.

	modules
		The default target for external modules. It has the
		same functionality as if no target was specified. See
		description above.

	modules_install
		Install the external module(s). The default location is
		/lib/modules/<kernel_release>/extra/, but a prefix may
		be added with INSTALL_MOD_PATH (discussed in section 5).

	clean
		Remove all generated files in the module directory only.

	help
		List the available targets for external modules.

--- 2.4 Building Separate Files

	It is possible to build single files that are part of a module.
	This works equally well for the kernel, a module, and even for
	external modules.

	Example (The module foo.ko, consist of bar.o and baz.o):
		make -C $KDIR M=$PWD bar.lst
		make -C $KDIR M=$PWD baz.o
		make -C $KDIR M=$PWD foo.ko
		make -C $KDIR M=$PWD ./


=== 3. Creating a Kbuild File for an External Module

In the last section we saw the command to build a module for the
running kernel. The module is not actually built, however, because a
build file is required. Contained in this file will be the name of
the module(s) being built, along with the list of requisite source
files. The file may be as simple as a single line:

	obj-m := <module_name>.o

The kbuild system will build <module_name>.o from <module_name>.c,
and, after linking, will result in the kernel module <module_name>.ko.
The above line can be put in either a "Kbuild" file or a "Makefile."
When the module is built from multiple sources, an additional line is
needed listing the files:

	<module_name>-y := <src1>.o <src2>.o ...

NOTE: Further documentation describing the syntax used by kbuild is
located in Documentation/kbuild/makefiles.txt.

The examples below demonstrate how to create a build file for the
module 8123.ko, which is built from the following files:

	8123_if.c
	8123_if.h
	8123_pci.c
	8123_bin.o_shipped	<= Binary blob

--- 3.1 Shared Makefile

	An external module always includes a wrapper makefile that
	supports building the module using "make" with no arguments.
	This target is not used by kbuild; it is only for convenience.
	Additional functionality, such as test targets, can be included
	but should be filtered out from kbuild due to possible name
	clashes.

	Example 1:
		--> filename: Makefile
		ifneq ($(KERNELRELEASE),)
		# kbuild part of makefile
		obj-m  := 8123.o
		8123-y := 8123_if.o 8123_pci.o 8123_bin.o

		else
		# normal makefile
		KDIR ?= /lib/modules/`uname -r`/build

		default:
			$(MAKE) -C $(KDIR) M=$$PWD

		# Module specific targets
		genbin:
			echo "X" > 8123_bin.o_shipped

		endif

	The check for KERNELRELEASE is used to separate the two parts
	of the makefile. In the example, kbuild will only see the two
	assignments, whereas "make" will see everything except these
	two assignments. This is due to two passes made on the file:
	the first pass is by the "make" instance run on the command
	line; the second pass is by the kbuild system, which is
	initiated by the parameterized "make" in the default target.

--- 3.2 Separate Kbuild File and Makefile

	In newer versions of the kernel, kbuild will first look for a
	file named "Kbuild," and only if that is not found, will it
	then look for a makefile. Utilizing a "Kbuild" file allows us
	to split up the makefile from example 1 into two files:

	Example 2:
		--> filename: Kbuild
		obj-m  := 8123.o
		8123-y := 8123_if.o 8123_pci.o 8123_bin.o

		--> filename: Makefile
		KDIR ?= /lib/modules/`uname -r`/build

		default:
			$(MAKE) -C $(KDIR) M=$$PWD

		# Module specific targets
		genbin:
			echo "X" > 8123_bin.o_shipped

	The split in example 2 is questionable due to the simplicity of
	each file; however, some external modules use makefiles
	consisting of several hundred lines, and here it really pays
	off to separate the kbuild part from the rest.

	The next example shows a backward compatible version.

	Example 3:
		--> filename: Kbuild
		obj-m  := 8123.o
		8123-y := 8123_if.o 8123_pci.o 8123_bin.o

		--> filename: Makefile
		ifneq ($(KERNELRELEASE),)
		# kbuild part of makefile
		include Kbuild

		else
		# normal makefile
		KDIR ?= /lib/modules/`uname -r`/build

		default:
			$(MAKE) -C $(KDIR) M=$$PWD

		# Module specific targets
		genbin:
			echo "X" > 8123_bin.o_shipped

		endif

	Here the "Kbuild" file is included from the makefile. This
	allows an older version of kbuild, which only knows of
	makefiles, to be used when the "make" and kbuild parts are
	split into separate files.

--- 3.3 Binary Blobs

	Some external modules need to include an object file as a blob.
	kbuild has support for this, but requires the blob file to be
	named <filename>_shipped. When the kbuild rules kick in, a copy
	of <filename>_shipped is created with _shipped stripped off,
	giving us <filename>. This shortened filename can be used in
	the assignment to the module.

	Throughout this section, 8123_bin.o_shipped has been used to
	build the kernel module 8123.ko; it has been included as
	8123_bin.o.

		8123-y := 8123_if.o 8123_pci.o 8123_bin.o

	Although there is no distinction between the ordinary source
	files and the binary file, kbuild will pick up different rules
	when creating the object file for the module.

--- 3.4 Building Multiple Modules

	kbuild supports building multiple modules with a single build
	file. For example, if you wanted to build two modules, foo.ko
	and bar.ko, the kbuild lines would be:

		obj-m := foo.o bar.o
		foo-y := <foo_srcs>
		bar-y := <bar_srcs>

	It is that simple!


=== 4. Include Files

Within the kernel, header files are kept in standard locations
according to the following rule:

	* If the header file only describes the internal interface of a
	  module, then the file is placed in the same directory as the
	  source files.
	* If the header file describes an interface used by other parts
	  of the kernel that are located in different directories, then
	  the file is placed in include/linux/.

	  NOTE: There are two notable exceptions to this rule: larger
	  subsystems have their own directory under include/, such as
	  include/scsi; and architecture specific headers are located
	  under arch/$(ARCH)/include/.

--- 4.1 Kernel Includes

	To include a header file located under include/linux/, simply
	use:

		#include <linux/module.h>

	kbuild will add options to "gcc" so the relevant directories
	are searched.

--- 4.2 Single Subdirectory

	External modules tend to place header files in a separate
	include/ directory where their source is located, although this
	is not the usual kernel style. To inform kbuild of the
	directory, use either ccflags-y or CFLAGS_<filename>.o.

	Using the example from section 3, if we moved 8123_if.h to a
	subdirectory named include, the resulting kbuild file would
	look like:

		--> filename: Kbuild
		obj-m := 8123.o

		ccflags-y := -Iinclude
		8123-y := 8123_if.o 8123_pci.o 8123_bin.o

	Note that in the assignment there is no space between -I and
	the path. This is a limitation of kbuild: there must be no
	space present.

--- 4.3 Several Subdirectories

	kbuild can handle files that are spread over several directories.
	Consider the following example:

	.
	|__ src
	|   |__ complex_main.c
	|   |__ hal
	|	|__ hardwareif.c
	|	|__ include
	|	    |__ hardwareif.h
	|__ include
	    |__ complex.h

	To build the module complex.ko, we then need the following
	kbuild file:

		--> filename: Kbuild
		obj-m := complex.o
		complex-y := src/complex_main.o
		complex-y += src/hal/hardwareif.o

		ccflags-y := -I$(src)/include
		ccflags-y += -I$(src)/src/hal/include

	As you can see, kbuild knows how to handle object files located
	in other directories. The trick is to specify the directory
	relative to the kbuild file's location. That being said, this
	is NOT recommended practice.

	For the header files, kbuild must be explicitly told where to
	look. When kbuild executes, the current directory is always the
	root of the kernel tree (the argument to "-C") and therefore an
	absolute path is needed. $(src) provides the absolute path by
	pointing to the directory where the currently executing kbuild
	file is located.


=== 5. Module Installation

Modules which are included in the kernel are installed in the
directory:

	/lib/modules/$(KERNELRELEASE)/kernel/

And external modules are installed in:

	/lib/modules/$(KERNELRELEASE)/extra/

--- 5.1 INSTALL_MOD_PATH

	Above are the default directories but as always some level of
	customization is possible. A prefix can be added to the
	installation path using the variable INSTALL_MOD_PATH:

		$ make INSTALL_MOD_PATH=/frodo modules_install
		=> Install dir: /frodo/lib/modules/$(KERNELRELEASE)/kernel/

	INSTALL_MOD_PATH may be set as an ordinary shell variable or,
	as shown above, can be specified on the command line when
	calling "make." This has effect when installing both in-tree
	and out-of-tree modules.

--- 5.2 INSTALL_MOD_DIR

	External modules are by default installed to a directory under
	/lib/modules/$(KERNELRELEASE)/extra/, but you may wish to
	locate modules for a specific functionality in a separate
	directory. For this purpose, use INSTALL_MOD_DIR to specify an
	alternative name to "extra."

		$ make INSTALL_MOD_DIR=gandalf -C $KDIR \
		       M=$PWD modules_install
		=> Install dir: /lib/modules/$(KERNELRELEASE)/gandalf/


=== 6. Module Versioning

Module versioning is enabled by the CONFIG_MODVERSIONS tag, and is used
as a simple ABI consistency check. A CRC value of the full prototype
for an exported symbol is created. When a module is loaded/used, the
CRC values contained in the kernel are compared with similar values in
the module; if they are not equal, the kernel refuses to load the
module.

Module.symvers contains a list of all exported symbols from a kernel
build.

--- 6.1 Symbols From the Kernel (vmlinux + modules)

	During a kernel build, a file named Module.symvers will be
	generated. Module.symvers contains all exported symbols from
	the kernel and compiled modules. For each symbol, the
	corresponding CRC value is also stored.

	The syntax of the Module.symvers file is:
		<CRC>	    <Symbol>	       <module>

		0x2d036834  scsi_remove_host   drivers/scsi/scsi_mod

	For a kernel build without CONFIG_MODVERSIONS enabled, the CRC
	would read 0x00000000.

	Module.symvers serves two purposes:
	1) It lists all exported symbols from vmlinux and all modules.
	2) It lists the CRC if CONFIG_MODVERSIONS is enabled.

--- 6.2 Symbols and External Modules

	When building an external module, the build system needs access
	to the symbols from the kernel to check if all external symbols
	are defined. This is done in the MODPOST step. modpost obtains
	the symbols by reading Module.symvers from the kernel source
	tree. If a Module.symvers file is present in the directory
	where the external module is being built, this file will be
	read too. During the MODPOST step, a new Module.symvers file
	will be written containing all exported symbols that were not
	defined in the kernel.

--- 6.3 Symbols From Another External Module

	Sometimes, an external module uses exported symbols from
	another external module. kbuild needs to have full knowledge of
	all symbols to avoid spitting out warnings about undefined
	symbols. Three solutions exist for this situation.

	NOTE: The method with a top-level kbuild file is recommended
	but may be impractical in certain situations.

	Use a top-level kbuild file
		If you have two modules, foo.ko and bar.ko, where
		foo.ko needs symbols from bar.ko, you can use a
		common top-level kbuild file so both modules are
		compiled in the same build. Consider the following
		directory layout:

		./foo/ <= contains foo.ko
		./bar/ <= contains bar.ko

		The top-level kbuild file would then look like:

		#./Kbuild (or ./Makefile):
			obj-y := foo/ bar/

		And executing

			$ make -C $KDIR M=$PWD

		will then do the expected and compile both modules with
		full knowledge of symbols from either module.

	Use an extra Module.symvers file
		When an external module is built, a Module.symvers file
		is generated containing all exported symbols which are
		not defined in the kernel. To get access to symbols
		from bar.ko, copy the Module.symvers file from the
		compilation of bar.ko to the directory where foo.ko is
		built. During the module build, kbuild will read the
		Module.symvers file in the directory of the external
		module, and when the build is finished, a new
		Module.symvers file is created containing the sum of
		all symbols defined and not part of the kernel.

	Use "make" variable KBUILD_EXTRA_SYMBOLS
		If it is impractical to copy Module.symvers from
		another module, you can assign a space separated list
		of files to KBUILD_EXTRA_SYMBOLS in your build file.
		These files will be loaded by modpost during the
		initialization of its symbol tables.


=== 7. Tips & Tricks

--- 7.1 Testing for CONFIG_FOO_BAR

	Modules often need to check for certain CONFIG_ options to
	decide if a specific feature is included in the module. In
	kbuild this is done by referencing the CONFIG_ variable
	directly.

		#fs/ext2/Makefile
		obj-$(CONFIG_EXT2_FS) += ext2.o

		ext2-y := balloc.o bitmap.o dir.o
		ext2-$(CONFIG_EXT2_FS_XATTR) += xattr.o

	External modules have traditionally used "grep" to check for
	specific CONFIG_ settings directly in .config. This usage is
	broken. As introduced before, external modules should use
	kbuild for building and can therefore use the same methods as
	in-tree modules when testing for CONFIG_ definitions.