mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-14 14:34:28 +08:00
8bb97bab3f
Add i2c_device_id table for the vl53l0x-i2c driver, helps in device instantiation using i2c_new_client_device() or from userspace in cases where device-tree based description is not possible now, like device(s) on a gbphy i2c adapter created by greybus. Signed-off-by: Vaishnav M A <vaishnav@beagleboard.org> Link: https://lore.kernel.org/r/20201018195102.GA814713@ubuntu Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
253 lines
6.0 KiB
C
253 lines
6.0 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Support for ST VL53L0X FlightSense ToF Ranging Sensor on a i2c bus.
|
|
*
|
|
* Copyright (C) 2016 STMicroelectronics Imaging Division.
|
|
* Copyright (C) 2018 Song Qiang <songqiang1304521@gmail.com>
|
|
* Copyright (C) 2020 Ivan Drobyshevskyi <drobyshevskyi@gmail.com>
|
|
*
|
|
* Datasheet available at
|
|
* <https://www.st.com/resource/en/datasheet/vl53l0x.pdf>
|
|
*
|
|
* Default 7-bit i2c slave address 0x29.
|
|
*
|
|
* TODO: FIFO buffer, continuous mode, range selection, sensor ID check.
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/iio/iio.h>
|
|
|
|
#define VL_REG_SYSRANGE_START 0x00
|
|
|
|
#define VL_REG_SYSRANGE_MODE_MASK GENMASK(3, 0)
|
|
#define VL_REG_SYSRANGE_MODE_SINGLESHOT 0x00
|
|
#define VL_REG_SYSRANGE_MODE_START_STOP BIT(0)
|
|
#define VL_REG_SYSRANGE_MODE_BACKTOBACK BIT(1)
|
|
#define VL_REG_SYSRANGE_MODE_TIMED BIT(2)
|
|
#define VL_REG_SYSRANGE_MODE_HISTOGRAM BIT(3)
|
|
|
|
#define VL_REG_SYSTEM_INTERRUPT_CONFIG_GPIO 0x0A
|
|
#define VL_REG_SYSTEM_INTERRUPT_GPIO_NEW_SAMPLE_READY BIT(2)
|
|
|
|
#define VL_REG_SYSTEM_INTERRUPT_CLEAR 0x0B
|
|
|
|
#define VL_REG_RESULT_INT_STATUS 0x13
|
|
#define VL_REG_RESULT_RANGE_STATUS 0x14
|
|
#define VL_REG_RESULT_RANGE_STATUS_COMPLETE BIT(0)
|
|
|
|
struct vl53l0x_data {
|
|
struct i2c_client *client;
|
|
struct completion completion;
|
|
};
|
|
|
|
static irqreturn_t vl53l0x_handle_irq(int irq, void *priv)
|
|
{
|
|
struct iio_dev *indio_dev = priv;
|
|
struct vl53l0x_data *data = iio_priv(indio_dev);
|
|
|
|
complete(&data->completion);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int vl53l0x_configure_irq(struct i2c_client *client,
|
|
struct iio_dev *indio_dev)
|
|
{
|
|
struct vl53l0x_data *data = iio_priv(indio_dev);
|
|
int ret;
|
|
|
|
ret = devm_request_irq(&client->dev, client->irq, vl53l0x_handle_irq,
|
|
IRQF_TRIGGER_FALLING, indio_dev->name, indio_dev);
|
|
if (ret) {
|
|
dev_err(&client->dev, "devm_request_irq error: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = i2c_smbus_write_byte_data(data->client,
|
|
VL_REG_SYSTEM_INTERRUPT_CONFIG_GPIO,
|
|
VL_REG_SYSTEM_INTERRUPT_GPIO_NEW_SAMPLE_READY);
|
|
if (ret < 0)
|
|
dev_err(&client->dev, "failed to configure IRQ: %d\n", ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void vl53l0x_clear_irq(struct vl53l0x_data *data)
|
|
{
|
|
struct device *dev = &data->client->dev;
|
|
int ret;
|
|
|
|
ret = i2c_smbus_write_byte_data(data->client,
|
|
VL_REG_SYSTEM_INTERRUPT_CLEAR, 1);
|
|
if (ret < 0)
|
|
dev_err(dev, "failed to clear error irq: %d\n", ret);
|
|
|
|
ret = i2c_smbus_write_byte_data(data->client,
|
|
VL_REG_SYSTEM_INTERRUPT_CLEAR, 0);
|
|
if (ret < 0)
|
|
dev_err(dev, "failed to clear range irq: %d\n", ret);
|
|
|
|
ret = i2c_smbus_read_byte_data(data->client, VL_REG_RESULT_INT_STATUS);
|
|
if (ret < 0 || ret & 0x07)
|
|
dev_err(dev, "failed to clear irq: %d\n", ret);
|
|
}
|
|
|
|
static int vl53l0x_read_proximity(struct vl53l0x_data *data,
|
|
const struct iio_chan_spec *chan,
|
|
int *val)
|
|
{
|
|
struct i2c_client *client = data->client;
|
|
u16 tries = 20;
|
|
u8 buffer[12];
|
|
int ret;
|
|
|
|
ret = i2c_smbus_write_byte_data(client, VL_REG_SYSRANGE_START, 1);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (data->client->irq) {
|
|
reinit_completion(&data->completion);
|
|
|
|
ret = wait_for_completion_timeout(&data->completion, HZ/10);
|
|
if (ret < 0)
|
|
return ret;
|
|
else if (ret == 0)
|
|
return -ETIMEDOUT;
|
|
|
|
vl53l0x_clear_irq(data);
|
|
} else {
|
|
do {
|
|
ret = i2c_smbus_read_byte_data(client,
|
|
VL_REG_RESULT_RANGE_STATUS);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (ret & VL_REG_RESULT_RANGE_STATUS_COMPLETE)
|
|
break;
|
|
|
|
usleep_range(1000, 5000);
|
|
} while (--tries);
|
|
if (!tries)
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
ret = i2c_smbus_read_i2c_block_data(client, VL_REG_RESULT_RANGE_STATUS,
|
|
12, buffer);
|
|
if (ret < 0)
|
|
return ret;
|
|
else if (ret != 12)
|
|
return -EREMOTEIO;
|
|
|
|
/* Values should be between 30~1200 in millimeters. */
|
|
*val = (buffer[10] << 8) + buffer[11];
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct iio_chan_spec vl53l0x_channels[] = {
|
|
{
|
|
.type = IIO_DISTANCE,
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
|
|
BIT(IIO_CHAN_INFO_SCALE),
|
|
},
|
|
};
|
|
|
|
static int vl53l0x_read_raw(struct iio_dev *indio_dev,
|
|
const struct iio_chan_spec *chan,
|
|
int *val, int *val2, long mask)
|
|
{
|
|
struct vl53l0x_data *data = iio_priv(indio_dev);
|
|
int ret;
|
|
|
|
if (chan->type != IIO_DISTANCE)
|
|
return -EINVAL;
|
|
|
|
switch (mask) {
|
|
case IIO_CHAN_INFO_RAW:
|
|
ret = vl53l0x_read_proximity(data, chan, val);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return IIO_VAL_INT;
|
|
case IIO_CHAN_INFO_SCALE:
|
|
*val = 0;
|
|
*val2 = 1000;
|
|
|
|
return IIO_VAL_INT_PLUS_MICRO;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
static const struct iio_info vl53l0x_info = {
|
|
.read_raw = vl53l0x_read_raw,
|
|
};
|
|
|
|
static int vl53l0x_probe(struct i2c_client *client)
|
|
{
|
|
struct vl53l0x_data *data;
|
|
struct iio_dev *indio_dev;
|
|
|
|
indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
|
|
if (!indio_dev)
|
|
return -ENOMEM;
|
|
|
|
data = iio_priv(indio_dev);
|
|
data->client = client;
|
|
i2c_set_clientdata(client, indio_dev);
|
|
|
|
if (!i2c_check_functionality(client->adapter,
|
|
I2C_FUNC_SMBUS_READ_I2C_BLOCK |
|
|
I2C_FUNC_SMBUS_BYTE_DATA))
|
|
return -EOPNOTSUPP;
|
|
|
|
indio_dev->name = "vl53l0x";
|
|
indio_dev->info = &vl53l0x_info;
|
|
indio_dev->channels = vl53l0x_channels;
|
|
indio_dev->num_channels = ARRAY_SIZE(vl53l0x_channels);
|
|
indio_dev->modes = INDIO_DIRECT_MODE;
|
|
|
|
/* usage of interrupt is optional */
|
|
if (client->irq) {
|
|
int ret;
|
|
|
|
init_completion(&data->completion);
|
|
|
|
ret = vl53l0x_configure_irq(client, indio_dev);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return devm_iio_device_register(&client->dev, indio_dev);
|
|
}
|
|
|
|
static const struct i2c_device_id vl53l0x_id[] = {
|
|
{ "vl53l0x", 0},
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, vl53l0x_id);
|
|
|
|
static const struct of_device_id st_vl53l0x_dt_match[] = {
|
|
{ .compatible = "st,vl53l0x", },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, st_vl53l0x_dt_match);
|
|
|
|
static struct i2c_driver vl53l0x_driver = {
|
|
.driver = {
|
|
.name = "vl53l0x-i2c",
|
|
.of_match_table = st_vl53l0x_dt_match,
|
|
},
|
|
.probe_new = vl53l0x_probe,
|
|
.id_table = vl53l0x_id,
|
|
};
|
|
module_i2c_driver(vl53l0x_driver);
|
|
|
|
MODULE_AUTHOR("Song Qiang <songqiang1304521@gmail.com>");
|
|
MODULE_DESCRIPTION("ST vl53l0x ToF ranging sensor driver");
|
|
MODULE_LICENSE("GPL v2");
|