mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-04 17:44:14 +08:00
c98be0c96d
Fixed multiple spelling errors. Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Carlos E. Garcia <carlos@cgarcia.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
114 lines
4.4 KiB
Plaintext
114 lines
4.4 KiB
Plaintext
|
|
About this document
|
|
===================
|
|
|
|
Some notes about Marvell's NAND controller available in PXA and Armada 370/XP
|
|
SoC (aka NFCv1 and NFCv2), with an emphasis on the latter.
|
|
|
|
NFCv2 controller background
|
|
===========================
|
|
|
|
The controller has a 2176 bytes FIFO buffer. Therefore, in order to support
|
|
larger pages, I/O operations on 4 KiB and 8 KiB pages is done with a set of
|
|
chunked transfers.
|
|
|
|
For instance, if we choose a 2048 data chunk and set "BCH" ECC (see below)
|
|
we'll have this layout in the pages:
|
|
|
|
------------------------------------------------------------------------------
|
|
| 2048B data | 32B spare | 30B ECC || 2048B data | 32B spare | 30B ECC | ... |
|
|
------------------------------------------------------------------------------
|
|
|
|
The driver reads the data and spare portions independently and builds an internal
|
|
buffer with this layout (in the 4 KiB page case):
|
|
|
|
------------------------------------------
|
|
| 4096B data | 64B spare |
|
|
------------------------------------------
|
|
|
|
Also, for the READOOB command the driver disables the ECC and reads a 'spare + ECC'
|
|
OOB, one per chunk read.
|
|
|
|
-------------------------------------------------------------------
|
|
| 4096B data | 32B spare | 30B ECC | 32B spare | 30B ECC |
|
|
-------------------------------------------------------------------
|
|
|
|
So, in order to achieve reading (for instance), we issue several READ0 commands
|
|
(with some additional controller-specific magic) and read two chunks of 2080B
|
|
(2048 data + 32 spare) each.
|
|
The driver accommodates this data to expose the NAND core a contiguous buffer
|
|
(4096 data + spare) or (4096 + spare + ECC + spare + ECC).
|
|
|
|
ECC
|
|
===
|
|
|
|
The controller has built-in hardware ECC capabilities. In addition it is
|
|
configurable between two modes: 1) Hamming, 2) BCH.
|
|
|
|
Note that the actual BCH mode: BCH-4 or BCH-8 will depend on the way
|
|
the controller is configured to transfer the data.
|
|
|
|
In the BCH mode the ECC code will be calculated for each transferred chunk
|
|
and expected to be located (when reading/programming) right after the spare
|
|
bytes as the figure above shows.
|
|
|
|
So, repeating the above scheme, a 2048B data chunk will be followed by 32B
|
|
spare, and then the ECC controller will read/write the ECC code (30B in
|
|
this case):
|
|
|
|
------------------------------------
|
|
| 2048B data | 32B spare | 30B ECC |
|
|
------------------------------------
|
|
|
|
If the ECC mode is 'BCH' then the ECC is *always* 30 bytes long.
|
|
If the ECC mode is 'Hamming' the ECC is 6 bytes long, for each 512B block.
|
|
So in Hamming mode, a 2048B page will have a 24B ECC.
|
|
|
|
Despite all of the above, the controller requires the driver to only read or
|
|
write in multiples of 8-bytes, because the data buffer is 64-bits.
|
|
|
|
OOB
|
|
===
|
|
|
|
Because of the above scheme, and because the "spare" OOB is really located in
|
|
the middle of a page, spare OOB cannot be read or write independently of the
|
|
data area. In other words, in order to read the OOB (aka READOOB), the entire
|
|
page (aka READ0) has to be read.
|
|
|
|
In the same sense, in order to write to the spare OOB the driver has to write
|
|
an *entire* page.
|
|
|
|
Factory bad blocks handling
|
|
===========================
|
|
|
|
Given the ECC BCH requires to layout the device's pages in a split
|
|
data/OOB/data/OOB way, the controller has a view of the flash page that's
|
|
different from the specified (aka the manufacturer's) view. In other words,
|
|
|
|
Factory view:
|
|
|
|
-----------------------------------------------
|
|
| Data |x OOB |
|
|
-----------------------------------------------
|
|
|
|
Driver's view:
|
|
|
|
-----------------------------------------------
|
|
| Data | OOB | Data x | OOB |
|
|
-----------------------------------------------
|
|
|
|
It can be seen from the above, that the factory bad block marker must be
|
|
searched within the 'data' region, and not in the usual OOB region.
|
|
|
|
In addition, this means under regular usage the driver will write such
|
|
position (since it belongs to the data region) and every used block is
|
|
likely to be marked as bad.
|
|
|
|
For this reason, marking the block as bad in the OOB is explicitly
|
|
disabled by using the NAND_BBT_NO_OOB_BBM option in the driver. The rationale
|
|
for this is that there's no point in marking a block as bad, because good
|
|
blocks are also 'marked as bad' (in the OOB BBM sense) under normal usage.
|
|
|
|
Instead, the driver relies on the bad block table alone, and should only perform
|
|
the bad block scan on the very first time (when the device hasn't been used).
|