mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-09 12:04:15 +08:00
ee6cac3736
Align the function names in the cy8c95x0_pmxops() to follow the struct pinmux_ops members naming schema. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20220916205450.86278-3-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1420 lines
35 KiB
C
1420 lines
35 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* CY8C95X0 20/40/60 pin I2C GPIO port expander with interrupt support
|
|
*
|
|
* Copyright (C) 2022 9elements GmbH
|
|
* Authors: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
* Naresh Solanki <Naresh.Solanki@9elements.com>
|
|
*/
|
|
|
|
#include <linux/acpi.h>
|
|
#include <linux/bitmap.h>
|
|
#include <linux/dmi.h>
|
|
#include <linux/gpio/driver.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/init.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/mod_devicetable.h>
|
|
#include <linux/module.h>
|
|
#include <linux/property.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/regulator/consumer.h>
|
|
|
|
#include <linux/pinctrl/pinctrl.h>
|
|
#include <linux/pinctrl/pinconf.h>
|
|
#include <linux/pinctrl/pinconf-generic.h>
|
|
#include <linux/pinctrl/pinmux.h>
|
|
|
|
/* Fast access registers */
|
|
#define CY8C95X0_INPUT 0x00
|
|
#define CY8C95X0_OUTPUT 0x08
|
|
#define CY8C95X0_INTSTATUS 0x10
|
|
|
|
#define CY8C95X0_INPUT_(x) (CY8C95X0_INPUT + (x))
|
|
#define CY8C95X0_OUTPUT_(x) (CY8C95X0_OUTPUT + (x))
|
|
#define CY8C95X0_INTSTATUS_(x) (CY8C95X0_INTSTATUS + (x))
|
|
|
|
/* Port Select configures the port */
|
|
#define CY8C95X0_PORTSEL 0x18
|
|
/* Port settings, write PORTSEL first */
|
|
#define CY8C95X0_INTMASK 0x19
|
|
#define CY8C95X0_PWMSEL 0x1A
|
|
#define CY8C95X0_INVERT 0x1B
|
|
#define CY8C95X0_DIRECTION 0x1C
|
|
/* Drive mode register change state on writing '1' */
|
|
#define CY8C95X0_DRV_PU 0x1D
|
|
#define CY8C95X0_DRV_PD 0x1E
|
|
#define CY8C95X0_DRV_ODH 0x1F
|
|
#define CY8C95X0_DRV_ODL 0x20
|
|
#define CY8C95X0_DRV_PP_FAST 0x21
|
|
#define CY8C95X0_DRV_PP_SLOW 0x22
|
|
#define CY8C95X0_DRV_HIZ 0x23
|
|
#define CY8C95X0_DEVID 0x2E
|
|
#define CY8C95X0_WATCHDOG 0x2F
|
|
#define CY8C95X0_COMMAND 0x30
|
|
|
|
#define CY8C95X0_PIN_TO_OFFSET(x) (((x) >= 20) ? ((x) + 4) : (x))
|
|
|
|
static const struct i2c_device_id cy8c95x0_id[] = {
|
|
{ "cy8c9520", 20, },
|
|
{ "cy8c9540", 40, },
|
|
{ "cy8c9560", 60, },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, cy8c95x0_id);
|
|
|
|
#define OF_CY8C95X(__nrgpio) ((void *)(__nrgpio))
|
|
|
|
static const struct of_device_id cy8c95x0_dt_ids[] = {
|
|
{ .compatible = "cypress,cy8c9520", .data = OF_CY8C95X(20), },
|
|
{ .compatible = "cypress,cy8c9540", .data = OF_CY8C95X(40), },
|
|
{ .compatible = "cypress,cy8c9560", .data = OF_CY8C95X(60), },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, cy8c95x0_dt_ids);
|
|
|
|
static const struct acpi_gpio_params cy8c95x0_irq_gpios = { 0, 0, true };
|
|
|
|
static const struct acpi_gpio_mapping cy8c95x0_acpi_irq_gpios[] = {
|
|
{ "irq-gpios", &cy8c95x0_irq_gpios, 1, ACPI_GPIO_QUIRK_ABSOLUTE_NUMBER },
|
|
{ }
|
|
};
|
|
|
|
static int cy8c95x0_acpi_get_irq(struct device *dev)
|
|
{
|
|
int ret;
|
|
|
|
ret = devm_acpi_dev_add_driver_gpios(dev, cy8c95x0_acpi_irq_gpios);
|
|
if (ret)
|
|
dev_warn(dev, "can't add GPIO ACPI mapping\n");
|
|
|
|
ret = acpi_dev_gpio_irq_get_by(ACPI_COMPANION(dev), "irq-gpios", 0);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
dev_info(dev, "ACPI interrupt quirk (IRQ %d)\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
static const struct dmi_system_id cy8c95x0_dmi_acpi_irq_info[] = {
|
|
{
|
|
/*
|
|
* On Intel Galileo Gen 1 board the IRQ pin is provided
|
|
* as an absolute number instead of being relative.
|
|
* Since first controller (gpio-sch.c) and second
|
|
* (gpio-dwapb.c) are at the fixed bases, we may safely
|
|
* refer to the number in the global space to get an IRQ
|
|
* out of it.
|
|
*/
|
|
.matches = {
|
|
DMI_EXACT_MATCH(DMI_BOARD_NAME, "Galileo"),
|
|
},
|
|
},
|
|
{}
|
|
};
|
|
|
|
#define MAX_BANK 8
|
|
#define BANK_SZ 8
|
|
#define MAX_LINE (MAX_BANK * BANK_SZ)
|
|
|
|
#define CY8C95X0_GPIO_MASK GENMASK(7, 0)
|
|
|
|
/**
|
|
* struct cy8c95x0_pinctrl - driver data
|
|
* @regmap: Device's regmap
|
|
* @irq_lock: IRQ bus lock
|
|
* @i2c_lock: Mutex for the device internal mux register
|
|
* @irq_mask: I/O bits affected by interrupts
|
|
* @irq_trig_raise: I/O bits affected by raising voltage level
|
|
* @irq_trig_fall: I/O bits affected by falling voltage level
|
|
* @irq_trig_low: I/O bits affected by a low voltage level
|
|
* @irq_trig_high: I/O bits affected by a high voltage level
|
|
* @push_pull: I/O bits configured as push pull driver
|
|
* @shiftmask: Mask used to compensate for Gport2 width
|
|
* @nport: Number of Gports in this chip
|
|
* @gpio_chip: gpiolib chip
|
|
* @driver_data: private driver data
|
|
* @regulator: Pointer to the regulator for the IC
|
|
* @dev: struct device
|
|
* @pctldev: pin controller device
|
|
* @pinctrl_desc: pin controller description
|
|
* @name: Chip controller name
|
|
* @tpin: Total number of pins
|
|
*/
|
|
struct cy8c95x0_pinctrl {
|
|
struct regmap *regmap;
|
|
struct mutex irq_lock;
|
|
struct mutex i2c_lock;
|
|
DECLARE_BITMAP(irq_mask, MAX_LINE);
|
|
DECLARE_BITMAP(irq_trig_raise, MAX_LINE);
|
|
DECLARE_BITMAP(irq_trig_fall, MAX_LINE);
|
|
DECLARE_BITMAP(irq_trig_low, MAX_LINE);
|
|
DECLARE_BITMAP(irq_trig_high, MAX_LINE);
|
|
DECLARE_BITMAP(push_pull, MAX_LINE);
|
|
DECLARE_BITMAP(shiftmask, MAX_LINE);
|
|
int nport;
|
|
struct gpio_chip gpio_chip;
|
|
unsigned long driver_data;
|
|
struct regulator *regulator;
|
|
struct device *dev;
|
|
struct pinctrl_dev *pctldev;
|
|
struct pinctrl_desc pinctrl_desc;
|
|
char name[32];
|
|
unsigned int tpin;
|
|
};
|
|
|
|
static const struct pinctrl_pin_desc cy8c9560_pins[] = {
|
|
PINCTRL_PIN(0, "gp00"),
|
|
PINCTRL_PIN(1, "gp01"),
|
|
PINCTRL_PIN(2, "gp02"),
|
|
PINCTRL_PIN(3, "gp03"),
|
|
PINCTRL_PIN(4, "gp04"),
|
|
PINCTRL_PIN(5, "gp05"),
|
|
PINCTRL_PIN(6, "gp06"),
|
|
PINCTRL_PIN(7, "gp07"),
|
|
|
|
PINCTRL_PIN(8, "gp10"),
|
|
PINCTRL_PIN(9, "gp11"),
|
|
PINCTRL_PIN(10, "gp12"),
|
|
PINCTRL_PIN(11, "gp13"),
|
|
PINCTRL_PIN(12, "gp14"),
|
|
PINCTRL_PIN(13, "gp15"),
|
|
PINCTRL_PIN(14, "gp16"),
|
|
PINCTRL_PIN(15, "gp17"),
|
|
|
|
PINCTRL_PIN(16, "gp20"),
|
|
PINCTRL_PIN(17, "gp21"),
|
|
PINCTRL_PIN(18, "gp22"),
|
|
PINCTRL_PIN(19, "gp23"),
|
|
|
|
PINCTRL_PIN(20, "gp30"),
|
|
PINCTRL_PIN(21, "gp31"),
|
|
PINCTRL_PIN(22, "gp32"),
|
|
PINCTRL_PIN(23, "gp33"),
|
|
PINCTRL_PIN(24, "gp34"),
|
|
PINCTRL_PIN(25, "gp35"),
|
|
PINCTRL_PIN(26, "gp36"),
|
|
PINCTRL_PIN(27, "gp37"),
|
|
|
|
PINCTRL_PIN(28, "gp40"),
|
|
PINCTRL_PIN(29, "gp41"),
|
|
PINCTRL_PIN(30, "gp42"),
|
|
PINCTRL_PIN(31, "gp43"),
|
|
PINCTRL_PIN(32, "gp44"),
|
|
PINCTRL_PIN(33, "gp45"),
|
|
PINCTRL_PIN(34, "gp46"),
|
|
PINCTRL_PIN(35, "gp47"),
|
|
|
|
PINCTRL_PIN(36, "gp50"),
|
|
PINCTRL_PIN(37, "gp51"),
|
|
PINCTRL_PIN(38, "gp52"),
|
|
PINCTRL_PIN(39, "gp53"),
|
|
PINCTRL_PIN(40, "gp54"),
|
|
PINCTRL_PIN(41, "gp55"),
|
|
PINCTRL_PIN(42, "gp56"),
|
|
PINCTRL_PIN(43, "gp57"),
|
|
|
|
PINCTRL_PIN(44, "gp60"),
|
|
PINCTRL_PIN(45, "gp61"),
|
|
PINCTRL_PIN(46, "gp62"),
|
|
PINCTRL_PIN(47, "gp63"),
|
|
PINCTRL_PIN(48, "gp64"),
|
|
PINCTRL_PIN(49, "gp65"),
|
|
PINCTRL_PIN(50, "gp66"),
|
|
PINCTRL_PIN(51, "gp67"),
|
|
|
|
PINCTRL_PIN(52, "gp70"),
|
|
PINCTRL_PIN(53, "gp71"),
|
|
PINCTRL_PIN(54, "gp72"),
|
|
PINCTRL_PIN(55, "gp73"),
|
|
PINCTRL_PIN(56, "gp74"),
|
|
PINCTRL_PIN(57, "gp75"),
|
|
PINCTRL_PIN(58, "gp76"),
|
|
PINCTRL_PIN(59, "gp77"),
|
|
};
|
|
|
|
static const char * const cy8c95x0_groups[] = {
|
|
"gp00",
|
|
"gp01",
|
|
"gp02",
|
|
"gp03",
|
|
"gp04",
|
|
"gp05",
|
|
"gp06",
|
|
"gp07",
|
|
|
|
"gp10",
|
|
"gp11",
|
|
"gp12",
|
|
"gp13",
|
|
"gp14",
|
|
"gp15",
|
|
"gp16",
|
|
"gp17",
|
|
|
|
"gp20",
|
|
"gp21",
|
|
"gp22",
|
|
"gp23",
|
|
|
|
"gp30",
|
|
"gp31",
|
|
"gp32",
|
|
"gp33",
|
|
"gp34",
|
|
"gp35",
|
|
"gp36",
|
|
"gp37",
|
|
|
|
"gp40",
|
|
"gp41",
|
|
"gp42",
|
|
"gp43",
|
|
"gp44",
|
|
"gp45",
|
|
"gp46",
|
|
"gp47",
|
|
|
|
"gp50",
|
|
"gp51",
|
|
"gp52",
|
|
"gp53",
|
|
"gp54",
|
|
"gp55",
|
|
"gp56",
|
|
"gp57",
|
|
|
|
"gp60",
|
|
"gp61",
|
|
"gp62",
|
|
"gp63",
|
|
"gp64",
|
|
"gp65",
|
|
"gp66",
|
|
"gp67",
|
|
|
|
"gp70",
|
|
"gp71",
|
|
"gp72",
|
|
"gp73",
|
|
"gp74",
|
|
"gp75",
|
|
"gp76",
|
|
"gp77",
|
|
};
|
|
|
|
static inline u8 cypress_get_port(struct cy8c95x0_pinctrl *chip, unsigned int pin)
|
|
{
|
|
/* Account for GPORT2 which only has 4 bits */
|
|
return CY8C95X0_PIN_TO_OFFSET(pin) / BANK_SZ;
|
|
}
|
|
|
|
static int cypress_get_pin_mask(struct cy8c95x0_pinctrl *chip, unsigned int pin)
|
|
{
|
|
/* Account for GPORT2 which only has 4 bits */
|
|
return BIT(CY8C95X0_PIN_TO_OFFSET(pin) % BANK_SZ);
|
|
}
|
|
|
|
static bool cy8c95x0_readable_register(struct device *dev, unsigned int reg)
|
|
{
|
|
switch (reg) {
|
|
case 0x24 ... 0x27:
|
|
return false;
|
|
default:
|
|
return true;
|
|
}
|
|
}
|
|
|
|
static bool cy8c95x0_writeable_register(struct device *dev, unsigned int reg)
|
|
{
|
|
switch (reg) {
|
|
case CY8C95X0_INPUT_(0) ... CY8C95X0_INPUT_(7):
|
|
return false;
|
|
case CY8C95X0_DEVID:
|
|
return false;
|
|
case 0x24 ... 0x27:
|
|
return false;
|
|
default:
|
|
return true;
|
|
}
|
|
}
|
|
|
|
static bool cy8c95x0_volatile_register(struct device *dev, unsigned int reg)
|
|
{
|
|
switch (reg) {
|
|
case CY8C95X0_INPUT_(0) ... CY8C95X0_INPUT_(7):
|
|
case CY8C95X0_INTSTATUS_(0) ... CY8C95X0_INTSTATUS_(7):
|
|
case CY8C95X0_INTMASK:
|
|
case CY8C95X0_INVERT:
|
|
case CY8C95X0_PWMSEL:
|
|
case CY8C95X0_DIRECTION:
|
|
case CY8C95X0_DRV_PU:
|
|
case CY8C95X0_DRV_PD:
|
|
case CY8C95X0_DRV_ODH:
|
|
case CY8C95X0_DRV_ODL:
|
|
case CY8C95X0_DRV_PP_FAST:
|
|
case CY8C95X0_DRV_PP_SLOW:
|
|
case CY8C95X0_DRV_HIZ:
|
|
return true;
|
|
default:
|
|
return false;
|
|
}
|
|
}
|
|
|
|
static bool cy8c95x0_precious_register(struct device *dev, unsigned int reg)
|
|
{
|
|
switch (reg) {
|
|
case CY8C95X0_INTSTATUS_(0) ... CY8C95X0_INTSTATUS_(7):
|
|
return true;
|
|
default:
|
|
return false;
|
|
}
|
|
}
|
|
|
|
static const struct reg_default cy8c95x0_reg_defaults[] = {
|
|
{ CY8C95X0_OUTPUT_(0), GENMASK(7, 0) },
|
|
{ CY8C95X0_OUTPUT_(1), GENMASK(7, 0) },
|
|
{ CY8C95X0_OUTPUT_(2), GENMASK(7, 0) },
|
|
{ CY8C95X0_OUTPUT_(3), GENMASK(7, 0) },
|
|
{ CY8C95X0_OUTPUT_(4), GENMASK(7, 0) },
|
|
{ CY8C95X0_OUTPUT_(5), GENMASK(7, 0) },
|
|
{ CY8C95X0_OUTPUT_(6), GENMASK(7, 0) },
|
|
{ CY8C95X0_OUTPUT_(7), GENMASK(7, 0) },
|
|
{ CY8C95X0_PORTSEL, 0 },
|
|
{ CY8C95X0_PWMSEL, 0 },
|
|
};
|
|
|
|
static const struct regmap_config cy8c95x0_i2c_regmap = {
|
|
.reg_bits = 8,
|
|
.val_bits = 8,
|
|
|
|
.reg_defaults = cy8c95x0_reg_defaults,
|
|
.num_reg_defaults = ARRAY_SIZE(cy8c95x0_reg_defaults),
|
|
|
|
.readable_reg = cy8c95x0_readable_register,
|
|
.writeable_reg = cy8c95x0_writeable_register,
|
|
.volatile_reg = cy8c95x0_volatile_register,
|
|
.precious_reg = cy8c95x0_precious_register,
|
|
|
|
.cache_type = REGCACHE_FLAT,
|
|
.max_register = CY8C95X0_COMMAND,
|
|
};
|
|
|
|
static int cy8c95x0_write_regs_mask(struct cy8c95x0_pinctrl *chip, int reg,
|
|
unsigned long *val, unsigned long *mask)
|
|
{
|
|
DECLARE_BITMAP(tmask, MAX_LINE);
|
|
DECLARE_BITMAP(tval, MAX_LINE);
|
|
int write_val;
|
|
int ret = 0;
|
|
int i, off = 0;
|
|
u8 bits;
|
|
|
|
/* Add the 4 bit gap of Gport2 */
|
|
bitmap_andnot(tmask, mask, chip->shiftmask, MAX_LINE);
|
|
bitmap_shift_left(tmask, tmask, 4, MAX_LINE);
|
|
bitmap_replace(tmask, tmask, mask, chip->shiftmask, BANK_SZ * 3);
|
|
|
|
bitmap_andnot(tval, val, chip->shiftmask, MAX_LINE);
|
|
bitmap_shift_left(tval, tval, 4, MAX_LINE);
|
|
bitmap_replace(tval, tval, val, chip->shiftmask, BANK_SZ * 3);
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
for (i = 0; i < chip->nport; i++) {
|
|
/* Skip over unused banks */
|
|
bits = bitmap_get_value8(tmask, i * BANK_SZ);
|
|
if (!bits)
|
|
continue;
|
|
|
|
switch (reg) {
|
|
/* Muxed registers */
|
|
case CY8C95X0_INTMASK:
|
|
case CY8C95X0_PWMSEL:
|
|
case CY8C95X0_INVERT:
|
|
case CY8C95X0_DIRECTION:
|
|
case CY8C95X0_DRV_PU:
|
|
case CY8C95X0_DRV_PD:
|
|
case CY8C95X0_DRV_ODH:
|
|
case CY8C95X0_DRV_ODL:
|
|
case CY8C95X0_DRV_PP_FAST:
|
|
case CY8C95X0_DRV_PP_SLOW:
|
|
case CY8C95X0_DRV_HIZ:
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, i);
|
|
if (ret < 0)
|
|
goto out;
|
|
off = reg;
|
|
break;
|
|
/* Direct access registers */
|
|
case CY8C95X0_INPUT:
|
|
case CY8C95X0_OUTPUT:
|
|
case CY8C95X0_INTSTATUS:
|
|
off = reg + i;
|
|
break;
|
|
default:
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
write_val = bitmap_get_value8(tval, i * BANK_SZ);
|
|
|
|
ret = regmap_update_bits(chip->regmap, off, bits, write_val);
|
|
if (ret < 0)
|
|
goto out;
|
|
}
|
|
out:
|
|
mutex_unlock(&chip->i2c_lock);
|
|
|
|
if (ret < 0)
|
|
dev_err(chip->dev, "failed writing register %d: err %d\n", off, ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_read_regs_mask(struct cy8c95x0_pinctrl *chip, int reg,
|
|
unsigned long *val, unsigned long *mask)
|
|
{
|
|
DECLARE_BITMAP(tmask, MAX_LINE);
|
|
DECLARE_BITMAP(tval, MAX_LINE);
|
|
DECLARE_BITMAP(tmp, MAX_LINE);
|
|
int read_val;
|
|
int ret = 0;
|
|
int i, off = 0;
|
|
u8 bits;
|
|
|
|
/* Add the 4 bit gap of Gport2 */
|
|
bitmap_andnot(tmask, mask, chip->shiftmask, MAX_LINE);
|
|
bitmap_shift_left(tmask, tmask, 4, MAX_LINE);
|
|
bitmap_replace(tmask, tmask, mask, chip->shiftmask, BANK_SZ * 3);
|
|
|
|
bitmap_andnot(tval, val, chip->shiftmask, MAX_LINE);
|
|
bitmap_shift_left(tval, tval, 4, MAX_LINE);
|
|
bitmap_replace(tval, tval, val, chip->shiftmask, BANK_SZ * 3);
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
for (i = 0; i < chip->nport; i++) {
|
|
/* Skip over unused banks */
|
|
bits = bitmap_get_value8(tmask, i * BANK_SZ);
|
|
if (!bits)
|
|
continue;
|
|
|
|
switch (reg) {
|
|
/* Muxed registers */
|
|
case CY8C95X0_INTMASK:
|
|
case CY8C95X0_PWMSEL:
|
|
case CY8C95X0_INVERT:
|
|
case CY8C95X0_DIRECTION:
|
|
case CY8C95X0_DRV_PU:
|
|
case CY8C95X0_DRV_PD:
|
|
case CY8C95X0_DRV_ODH:
|
|
case CY8C95X0_DRV_ODL:
|
|
case CY8C95X0_DRV_PP_FAST:
|
|
case CY8C95X0_DRV_PP_SLOW:
|
|
case CY8C95X0_DRV_HIZ:
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, i);
|
|
if (ret < 0)
|
|
goto out;
|
|
off = reg;
|
|
break;
|
|
/* Direct access registers */
|
|
case CY8C95X0_INPUT:
|
|
case CY8C95X0_OUTPUT:
|
|
case CY8C95X0_INTSTATUS:
|
|
off = reg + i;
|
|
break;
|
|
default:
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
ret = regmap_read(chip->regmap, off, &read_val);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
read_val &= bits;
|
|
read_val |= bitmap_get_value8(tval, i * BANK_SZ) & ~bits;
|
|
bitmap_set_value8(tval, read_val, i * BANK_SZ);
|
|
}
|
|
|
|
/* Fill the 4 bit gap of Gport2 */
|
|
bitmap_shift_right(tmp, tval, 4, MAX_LINE);
|
|
bitmap_replace(val, tmp, tval, chip->shiftmask, MAX_LINE);
|
|
|
|
out:
|
|
mutex_unlock(&chip->i2c_lock);
|
|
|
|
if (ret < 0)
|
|
dev_err(chip->dev, "failed reading register %d: err %d\n", off, ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_gpio_direction_input(struct gpio_chip *gc, unsigned int off)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
u8 port = cypress_get_port(chip, off);
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
int ret;
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = regmap_write_bits(chip->regmap, CY8C95X0_DIRECTION, bit, bit);
|
|
if (ret)
|
|
goto out;
|
|
|
|
if (test_bit(off, chip->push_pull)) {
|
|
/*
|
|
* Disable driving the pin by forcing it to HighZ. Only setting the
|
|
* direction register isn't sufficient in Push-Pull mode.
|
|
*/
|
|
ret = regmap_write_bits(chip->regmap, CY8C95X0_DRV_HIZ, bit, bit);
|
|
if (ret)
|
|
goto out;
|
|
|
|
__clear_bit(off, chip->push_pull);
|
|
}
|
|
|
|
out:
|
|
mutex_unlock(&chip->i2c_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_gpio_direction_output(struct gpio_chip *gc,
|
|
unsigned int off, int val)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
u8 port = cypress_get_port(chip, off);
|
|
u8 outreg = CY8C95X0_OUTPUT_(port);
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
int ret;
|
|
|
|
/* Set output level */
|
|
ret = regmap_write_bits(chip->regmap, outreg, bit, val ? bit : 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
/* Select port... */
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* ...then direction */
|
|
ret = regmap_write_bits(chip->regmap, CY8C95X0_DIRECTION, bit, 0);
|
|
|
|
out:
|
|
mutex_unlock(&chip->i2c_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_gpio_get_value(struct gpio_chip *gc, unsigned int off)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
u8 inreg = CY8C95X0_INPUT_(cypress_get_port(chip, off));
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
u32 reg_val;
|
|
int ret;
|
|
|
|
ret = regmap_read(chip->regmap, inreg, ®_val);
|
|
if (ret < 0) {
|
|
/*
|
|
* NOTE:
|
|
* Diagnostic already emitted; that's all we should
|
|
* do unless gpio_*_value_cansleep() calls become different
|
|
* from their nonsleeping siblings (and report faults).
|
|
*/
|
|
return 0;
|
|
}
|
|
|
|
return !!(reg_val & bit);
|
|
}
|
|
|
|
static void cy8c95x0_gpio_set_value(struct gpio_chip *gc, unsigned int off,
|
|
int val)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
u8 outreg = CY8C95X0_OUTPUT_(cypress_get_port(chip, off));
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
|
|
regmap_write_bits(chip->regmap, outreg, bit, val ? bit : 0);
|
|
}
|
|
|
|
static int cy8c95x0_gpio_get_direction(struct gpio_chip *gc, unsigned int off)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
u8 port = cypress_get_port(chip, off);
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
u32 reg_val;
|
|
int ret;
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
ret = regmap_read(chip->regmap, CY8C95X0_DIRECTION, ®_val);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
mutex_unlock(&chip->i2c_lock);
|
|
|
|
if (reg_val & bit)
|
|
return GPIO_LINE_DIRECTION_IN;
|
|
|
|
return GPIO_LINE_DIRECTION_OUT;
|
|
out:
|
|
mutex_unlock(&chip->i2c_lock);
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_gpio_get_pincfg(struct cy8c95x0_pinctrl *chip,
|
|
unsigned int off,
|
|
unsigned long *config)
|
|
{
|
|
enum pin_config_param param = pinconf_to_config_param(*config);
|
|
u8 port = cypress_get_port(chip, off);
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
unsigned int reg;
|
|
u32 reg_val;
|
|
u16 arg = 0;
|
|
int ret;
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
|
|
/* Select port */
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
switch (param) {
|
|
case PIN_CONFIG_BIAS_PULL_UP:
|
|
reg = CY8C95X0_DRV_PU;
|
|
break;
|
|
case PIN_CONFIG_BIAS_PULL_DOWN:
|
|
reg = CY8C95X0_DRV_PD;
|
|
break;
|
|
case PIN_CONFIG_BIAS_DISABLE:
|
|
reg = CY8C95X0_DRV_HIZ;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
|
|
reg = CY8C95X0_DRV_ODL;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_OPEN_SOURCE:
|
|
reg = CY8C95X0_DRV_ODH;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_PUSH_PULL:
|
|
reg = CY8C95X0_DRV_PP_FAST;
|
|
break;
|
|
case PIN_CONFIG_INPUT_ENABLE:
|
|
reg = CY8C95X0_DIRECTION;
|
|
break;
|
|
case PIN_CONFIG_MODE_PWM:
|
|
reg = CY8C95X0_PWMSEL;
|
|
break;
|
|
case PIN_CONFIG_OUTPUT:
|
|
reg = CY8C95X0_OUTPUT_(port);
|
|
break;
|
|
case PIN_CONFIG_OUTPUT_ENABLE:
|
|
reg = CY8C95X0_DIRECTION;
|
|
break;
|
|
|
|
case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
|
|
case PIN_CONFIG_BIAS_BUS_HOLD:
|
|
case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
|
|
case PIN_CONFIG_DRIVE_STRENGTH:
|
|
case PIN_CONFIG_DRIVE_STRENGTH_UA:
|
|
case PIN_CONFIG_INPUT_DEBOUNCE:
|
|
case PIN_CONFIG_INPUT_SCHMITT:
|
|
case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
|
|
case PIN_CONFIG_MODE_LOW_POWER:
|
|
case PIN_CONFIG_PERSIST_STATE:
|
|
case PIN_CONFIG_POWER_SOURCE:
|
|
case PIN_CONFIG_SKEW_DELAY:
|
|
case PIN_CONFIG_SLEEP_HARDWARE_STATE:
|
|
case PIN_CONFIG_SLEW_RATE:
|
|
default:
|
|
ret = -ENOTSUPP;
|
|
goto out;
|
|
}
|
|
/*
|
|
* Writing 1 to one of the drive mode registers will automatically
|
|
* clear conflicting set bits in the other drive mode registers.
|
|
*/
|
|
ret = regmap_read(chip->regmap, reg, ®_val);
|
|
if (reg_val & bit)
|
|
arg = 1;
|
|
|
|
*config = pinconf_to_config_packed(param, (u16)arg);
|
|
out:
|
|
mutex_unlock(&chip->i2c_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_gpio_set_pincfg(struct cy8c95x0_pinctrl *chip,
|
|
unsigned int off,
|
|
unsigned long config)
|
|
{
|
|
u8 port = cypress_get_port(chip, off);
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
unsigned long param = pinconf_to_config_param(config);
|
|
unsigned int reg;
|
|
int ret;
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
|
|
/* Select port */
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
switch (param) {
|
|
case PIN_CONFIG_BIAS_PULL_UP:
|
|
__clear_bit(off, chip->push_pull);
|
|
reg = CY8C95X0_DRV_PU;
|
|
break;
|
|
case PIN_CONFIG_BIAS_PULL_DOWN:
|
|
__clear_bit(off, chip->push_pull);
|
|
reg = CY8C95X0_DRV_PD;
|
|
break;
|
|
case PIN_CONFIG_BIAS_DISABLE:
|
|
__clear_bit(off, chip->push_pull);
|
|
reg = CY8C95X0_DRV_HIZ;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
|
|
__clear_bit(off, chip->push_pull);
|
|
reg = CY8C95X0_DRV_ODL;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_OPEN_SOURCE:
|
|
__clear_bit(off, chip->push_pull);
|
|
reg = CY8C95X0_DRV_ODH;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_PUSH_PULL:
|
|
__set_bit(off, chip->push_pull);
|
|
reg = CY8C95X0_DRV_PP_FAST;
|
|
break;
|
|
case PIN_CONFIG_MODE_PWM:
|
|
reg = CY8C95X0_PWMSEL;
|
|
break;
|
|
default:
|
|
ret = -ENOTSUPP;
|
|
goto out;
|
|
}
|
|
/*
|
|
* Writing 1 to one of the drive mode registers will automatically
|
|
* clear conflicting set bits in the other drive mode registers.
|
|
*/
|
|
ret = regmap_write_bits(chip->regmap, reg, bit, bit);
|
|
|
|
out:
|
|
mutex_unlock(&chip->i2c_lock);
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_gpio_get_multiple(struct gpio_chip *gc,
|
|
unsigned long *mask, unsigned long *bits)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
|
|
return cy8c95x0_read_regs_mask(chip, CY8C95X0_INPUT, bits, mask);
|
|
}
|
|
|
|
static void cy8c95x0_gpio_set_multiple(struct gpio_chip *gc,
|
|
unsigned long *mask, unsigned long *bits)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
|
|
cy8c95x0_write_regs_mask(chip, CY8C95X0_OUTPUT, bits, mask);
|
|
}
|
|
|
|
static int cy8c95x0_add_pin_ranges(struct gpio_chip *gc)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
struct device *dev = chip->dev;
|
|
int ret;
|
|
|
|
ret = gpiochip_add_pin_range(gc, dev_name(dev), 0, 0, chip->tpin);
|
|
if (ret)
|
|
dev_err(dev, "failed to add GPIO pin range\n");
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int cy8c95x0_setup_gpiochip(struct cy8c95x0_pinctrl *chip)
|
|
{
|
|
struct gpio_chip *gc = &chip->gpio_chip;
|
|
|
|
gc->direction_input = cy8c95x0_gpio_direction_input;
|
|
gc->direction_output = cy8c95x0_gpio_direction_output;
|
|
gc->get = cy8c95x0_gpio_get_value;
|
|
gc->set = cy8c95x0_gpio_set_value;
|
|
gc->get_direction = cy8c95x0_gpio_get_direction;
|
|
gc->get_multiple = cy8c95x0_gpio_get_multiple;
|
|
gc->set_multiple = cy8c95x0_gpio_set_multiple;
|
|
gc->set_config = gpiochip_generic_config,
|
|
gc->can_sleep = true;
|
|
gc->add_pin_ranges = cy8c95x0_add_pin_ranges;
|
|
|
|
gc->base = -1;
|
|
gc->ngpio = chip->tpin;
|
|
|
|
gc->parent = chip->dev;
|
|
gc->owner = THIS_MODULE;
|
|
gc->names = NULL;
|
|
|
|
gc->label = dev_name(chip->dev);
|
|
|
|
return devm_gpiochip_add_data(chip->dev, gc, chip);
|
|
}
|
|
|
|
static void cy8c95x0_irq_mask(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
irq_hw_number_t hwirq = irqd_to_hwirq(d);
|
|
|
|
set_bit(hwirq, chip->irq_mask);
|
|
gpiochip_disable_irq(gc, hwirq);
|
|
}
|
|
|
|
static void cy8c95x0_irq_unmask(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
irq_hw_number_t hwirq = irqd_to_hwirq(d);
|
|
|
|
gpiochip_enable_irq(gc, hwirq);
|
|
clear_bit(hwirq, chip->irq_mask);
|
|
}
|
|
|
|
static void cy8c95x0_irq_bus_lock(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
|
|
mutex_lock(&chip->irq_lock);
|
|
}
|
|
|
|
static void cy8c95x0_irq_bus_sync_unlock(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
DECLARE_BITMAP(ones, MAX_LINE);
|
|
DECLARE_BITMAP(irq_mask, MAX_LINE);
|
|
DECLARE_BITMAP(reg_direction, MAX_LINE);
|
|
|
|
bitmap_fill(ones, MAX_LINE);
|
|
|
|
cy8c95x0_write_regs_mask(chip, CY8C95X0_INTMASK, chip->irq_mask, ones);
|
|
|
|
/* Switch direction to input if needed */
|
|
cy8c95x0_read_regs_mask(chip, CY8C95X0_DIRECTION, reg_direction, chip->irq_mask);
|
|
bitmap_or(irq_mask, chip->irq_mask, reg_direction, MAX_LINE);
|
|
bitmap_complement(irq_mask, irq_mask, MAX_LINE);
|
|
|
|
/* Look for any newly setup interrupt */
|
|
cy8c95x0_write_regs_mask(chip, CY8C95X0_DIRECTION, ones, irq_mask);
|
|
|
|
mutex_unlock(&chip->irq_lock);
|
|
}
|
|
|
|
static int cy8c95x0_irq_set_type(struct irq_data *d, unsigned int type)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
irq_hw_number_t hwirq = irqd_to_hwirq(d);
|
|
unsigned int trig_type;
|
|
|
|
switch (type) {
|
|
case IRQ_TYPE_EDGE_RISING:
|
|
case IRQ_TYPE_EDGE_FALLING:
|
|
case IRQ_TYPE_EDGE_BOTH:
|
|
trig_type = type;
|
|
break;
|
|
case IRQ_TYPE_LEVEL_HIGH:
|
|
trig_type = IRQ_TYPE_EDGE_RISING;
|
|
break;
|
|
case IRQ_TYPE_LEVEL_LOW:
|
|
trig_type = IRQ_TYPE_EDGE_FALLING;
|
|
break;
|
|
default:
|
|
dev_err(chip->dev, "irq %d: unsupported type %d\n", d->irq, type);
|
|
return -EINVAL;
|
|
}
|
|
|
|
assign_bit(hwirq, chip->irq_trig_fall, trig_type & IRQ_TYPE_EDGE_FALLING);
|
|
assign_bit(hwirq, chip->irq_trig_raise, trig_type & IRQ_TYPE_EDGE_RISING);
|
|
assign_bit(hwirq, chip->irq_trig_low, type == IRQ_TYPE_LEVEL_LOW);
|
|
assign_bit(hwirq, chip->irq_trig_high, type == IRQ_TYPE_LEVEL_HIGH);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void cy8c95x0_irq_shutdown(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc);
|
|
irq_hw_number_t hwirq = irqd_to_hwirq(d);
|
|
|
|
clear_bit(hwirq, chip->irq_trig_raise);
|
|
clear_bit(hwirq, chip->irq_trig_fall);
|
|
clear_bit(hwirq, chip->irq_trig_low);
|
|
clear_bit(hwirq, chip->irq_trig_high);
|
|
}
|
|
|
|
static const struct irq_chip cy8c95x0_irqchip = {
|
|
.name = "cy8c95x0-irq",
|
|
.irq_mask = cy8c95x0_irq_mask,
|
|
.irq_unmask = cy8c95x0_irq_unmask,
|
|
.irq_bus_lock = cy8c95x0_irq_bus_lock,
|
|
.irq_bus_sync_unlock = cy8c95x0_irq_bus_sync_unlock,
|
|
.irq_set_type = cy8c95x0_irq_set_type,
|
|
.irq_shutdown = cy8c95x0_irq_shutdown,
|
|
.flags = IRQCHIP_IMMUTABLE,
|
|
GPIOCHIP_IRQ_RESOURCE_HELPERS,
|
|
};
|
|
|
|
static bool cy8c95x0_irq_pending(struct cy8c95x0_pinctrl *chip, unsigned long *pending)
|
|
{
|
|
DECLARE_BITMAP(ones, MAX_LINE);
|
|
DECLARE_BITMAP(cur_stat, MAX_LINE);
|
|
DECLARE_BITMAP(new_stat, MAX_LINE);
|
|
DECLARE_BITMAP(trigger, MAX_LINE);
|
|
|
|
bitmap_fill(ones, MAX_LINE);
|
|
|
|
/* Read the current interrupt status from the device */
|
|
if (cy8c95x0_read_regs_mask(chip, CY8C95X0_INTSTATUS, trigger, ones))
|
|
return false;
|
|
|
|
/* Check latched inputs */
|
|
if (cy8c95x0_read_regs_mask(chip, CY8C95X0_INPUT, cur_stat, trigger))
|
|
return false;
|
|
|
|
/* Apply filter for rising/falling edge selection */
|
|
bitmap_replace(new_stat, chip->irq_trig_fall, chip->irq_trig_raise,
|
|
cur_stat, MAX_LINE);
|
|
|
|
bitmap_and(pending, new_stat, trigger, MAX_LINE);
|
|
|
|
return !bitmap_empty(pending, MAX_LINE);
|
|
}
|
|
|
|
static irqreturn_t cy8c95x0_irq_handler(int irq, void *devid)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = devid;
|
|
struct gpio_chip *gc = &chip->gpio_chip;
|
|
DECLARE_BITMAP(pending, MAX_LINE);
|
|
int nested_irq, level;
|
|
bool ret;
|
|
|
|
ret = cy8c95x0_irq_pending(chip, pending);
|
|
if (!ret)
|
|
return IRQ_RETVAL(0);
|
|
|
|
ret = 0;
|
|
for_each_set_bit(level, pending, MAX_LINE) {
|
|
/* Already accounted for 4bit gap in GPort2 */
|
|
nested_irq = irq_find_mapping(gc->irq.domain, level);
|
|
|
|
if (unlikely(nested_irq <= 0)) {
|
|
dev_warn_ratelimited(gc->parent, "unmapped interrupt %d\n", level);
|
|
continue;
|
|
}
|
|
|
|
if (test_bit(level, chip->irq_trig_low))
|
|
while (!cy8c95x0_gpio_get_value(gc, level))
|
|
handle_nested_irq(nested_irq);
|
|
else if (test_bit(level, chip->irq_trig_high))
|
|
while (cy8c95x0_gpio_get_value(gc, level))
|
|
handle_nested_irq(nested_irq);
|
|
else
|
|
handle_nested_irq(nested_irq);
|
|
|
|
ret = 1;
|
|
}
|
|
|
|
return IRQ_RETVAL(ret);
|
|
}
|
|
|
|
static int cy8c95x0_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
return chip->tpin;
|
|
}
|
|
|
|
static const char *cy8c95x0_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
|
|
unsigned int group)
|
|
{
|
|
return cy8c95x0_groups[group];
|
|
}
|
|
|
|
static int cy8c95x0_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
|
|
unsigned int group,
|
|
const unsigned int **pins,
|
|
unsigned int *num_pins)
|
|
{
|
|
*pins = &cy8c9560_pins[group].number;
|
|
*num_pins = 1;
|
|
return 0;
|
|
}
|
|
|
|
static const char *cy8c95x0_get_fname(unsigned int selector)
|
|
{
|
|
if (selector == 0)
|
|
return "gpio";
|
|
else
|
|
return "pwm";
|
|
}
|
|
|
|
static void cy8c95x0_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
|
|
unsigned int pin)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev);
|
|
DECLARE_BITMAP(mask, MAX_LINE);
|
|
DECLARE_BITMAP(pwm, MAX_LINE);
|
|
|
|
bitmap_zero(mask, MAX_LINE);
|
|
__set_bit(pin, mask);
|
|
|
|
if (cy8c95x0_read_regs_mask(chip, CY8C95X0_PWMSEL, pwm, mask)) {
|
|
seq_puts(s, "not available");
|
|
return;
|
|
}
|
|
|
|
seq_printf(s, "MODE:%s", cy8c95x0_get_fname(test_bit(pin, pwm)));
|
|
}
|
|
|
|
static const struct pinctrl_ops cy8c95x0_pinctrl_ops = {
|
|
.get_groups_count = cy8c95x0_pinctrl_get_groups_count,
|
|
.get_group_name = cy8c95x0_pinctrl_get_group_name,
|
|
.get_group_pins = cy8c95x0_pinctrl_get_group_pins,
|
|
#ifdef CONFIG_OF
|
|
.dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
|
|
.dt_free_map = pinconf_generic_dt_free_map,
|
|
#endif
|
|
.pin_dbg_show = cy8c95x0_pin_dbg_show,
|
|
};
|
|
|
|
static const char *cy8c95x0_get_function_name(struct pinctrl_dev *pctldev, unsigned int selector)
|
|
{
|
|
return cy8c95x0_get_fname(selector);
|
|
}
|
|
|
|
static int cy8c95x0_get_functions_count(struct pinctrl_dev *pctldev)
|
|
{
|
|
return 2;
|
|
}
|
|
|
|
static int cy8c95x0_get_function_groups(struct pinctrl_dev *pctldev, unsigned int selector,
|
|
const char * const **groups,
|
|
unsigned int * const num_groups)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
*groups = cy8c95x0_groups;
|
|
*num_groups = chip->tpin;
|
|
return 0;
|
|
}
|
|
|
|
static int cy8c95x0_pinmux_cfg(struct cy8c95x0_pinctrl *chip,
|
|
unsigned int val,
|
|
unsigned long off)
|
|
{
|
|
u8 port = cypress_get_port(chip, off);
|
|
u8 bit = cypress_get_pin_mask(chip, off);
|
|
int ret;
|
|
|
|
/* Select port */
|
|
ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = regmap_write_bits(chip->regmap, CY8C95X0_PWMSEL, bit, val ? bit : 0);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Set direction to output & set output to 1 so that PWM can work */
|
|
ret = regmap_write_bits(chip->regmap, CY8C95X0_DIRECTION, bit, bit);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return regmap_write_bits(chip->regmap, CY8C95X0_OUTPUT_(port), bit, bit);
|
|
}
|
|
|
|
static int cy8c95x0_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
|
|
unsigned int group)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev);
|
|
int ret;
|
|
|
|
mutex_lock(&chip->i2c_lock);
|
|
ret = cy8c95x0_pinmux_cfg(chip, selector, group);
|
|
mutex_unlock(&chip->i2c_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static const struct pinmux_ops cy8c95x0_pmxops = {
|
|
.get_functions_count = cy8c95x0_get_functions_count,
|
|
.get_function_name = cy8c95x0_get_function_name,
|
|
.get_function_groups = cy8c95x0_get_function_groups,
|
|
.set_mux = cy8c95x0_set_mux,
|
|
.strict = true,
|
|
};
|
|
|
|
static int cy8c95x0_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
|
|
unsigned long *config)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
return cy8c95x0_gpio_get_pincfg(chip, pin, config);
|
|
}
|
|
|
|
static int cy8c95x0_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
|
|
unsigned long *configs, unsigned int num_configs)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev);
|
|
int ret = 0;
|
|
int i;
|
|
|
|
for (i = 0; i < num_configs; i++) {
|
|
ret = cy8c95x0_gpio_set_pincfg(chip, pin, configs[i]);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static const struct pinconf_ops cy8c95x0_pinconf_ops = {
|
|
.pin_config_get = cy8c95x0_pinconf_get,
|
|
.pin_config_set = cy8c95x0_pinconf_set,
|
|
.is_generic = true,
|
|
};
|
|
|
|
static int cy8c95x0_irq_setup(struct cy8c95x0_pinctrl *chip, int irq)
|
|
{
|
|
struct gpio_irq_chip *girq = &chip->gpio_chip.irq;
|
|
DECLARE_BITMAP(pending_irqs, MAX_LINE);
|
|
int ret;
|
|
|
|
mutex_init(&chip->irq_lock);
|
|
|
|
bitmap_zero(pending_irqs, MAX_LINE);
|
|
|
|
/* Read IRQ status register to clear all pending interrupts */
|
|
ret = cy8c95x0_irq_pending(chip, pending_irqs);
|
|
if (ret) {
|
|
dev_err(chip->dev, "failed to clear irq status register\n");
|
|
return ret;
|
|
}
|
|
|
|
/* Mask all interrupts */
|
|
bitmap_fill(chip->irq_mask, MAX_LINE);
|
|
|
|
gpio_irq_chip_set_chip(girq, &cy8c95x0_irqchip);
|
|
|
|
/* This will let us handle the parent IRQ in the driver */
|
|
girq->parent_handler = NULL;
|
|
girq->num_parents = 0;
|
|
girq->parents = NULL;
|
|
girq->default_type = IRQ_TYPE_NONE;
|
|
girq->handler = handle_simple_irq;
|
|
girq->threaded = true;
|
|
|
|
ret = devm_request_threaded_irq(chip->dev, irq,
|
|
NULL, cy8c95x0_irq_handler,
|
|
IRQF_ONESHOT | IRQF_SHARED | IRQF_TRIGGER_HIGH,
|
|
dev_name(chip->dev), chip);
|
|
if (ret) {
|
|
dev_err(chip->dev, "failed to request irq %d\n", irq);
|
|
return ret;
|
|
}
|
|
dev_info(chip->dev, "Registered threaded IRQ\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cy8c95x0_setup_pinctrl(struct cy8c95x0_pinctrl *chip)
|
|
{
|
|
struct pinctrl_desc *pd = &chip->pinctrl_desc;
|
|
|
|
pd->pctlops = &cy8c95x0_pinctrl_ops;
|
|
pd->confops = &cy8c95x0_pinconf_ops;
|
|
pd->pmxops = &cy8c95x0_pmxops;
|
|
pd->name = dev_name(chip->dev);
|
|
pd->pins = cy8c9560_pins;
|
|
pd->npins = chip->tpin;
|
|
pd->owner = THIS_MODULE;
|
|
|
|
chip->pctldev = devm_pinctrl_register(chip->dev, pd, chip);
|
|
if (IS_ERR(chip->pctldev))
|
|
return dev_err_probe(chip->dev, PTR_ERR(chip->pctldev),
|
|
"can't register controller\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cy8c95x0_detect(struct i2c_client *client,
|
|
struct i2c_board_info *info)
|
|
{
|
|
struct i2c_adapter *adapter = client->adapter;
|
|
int ret;
|
|
const char *name;
|
|
|
|
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
|
|
return -ENODEV;
|
|
|
|
ret = i2c_smbus_read_byte_data(client, CY8C95X0_DEVID);
|
|
if (ret < 0)
|
|
return ret;
|
|
switch (ret & GENMASK(7, 4)) {
|
|
case 0x20:
|
|
name = cy8c95x0_id[0].name;
|
|
break;
|
|
case 0x40:
|
|
name = cy8c95x0_id[1].name;
|
|
break;
|
|
case 0x60:
|
|
name = cy8c95x0_id[2].name;
|
|
break;
|
|
default:
|
|
return -ENODEV;
|
|
}
|
|
|
|
dev_info(&client->dev, "Found a %s chip at 0x%02x.\n", name, client->addr);
|
|
strscpy(info->type, name, I2C_NAME_SIZE);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cy8c95x0_probe(struct i2c_client *client)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip;
|
|
struct regulator *reg;
|
|
int ret;
|
|
|
|
chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
|
|
if (!chip)
|
|
return -ENOMEM;
|
|
|
|
chip->dev = &client->dev;
|
|
|
|
/* Set the device type */
|
|
chip->driver_data = (unsigned long)device_get_match_data(&client->dev);
|
|
if (!chip->driver_data)
|
|
chip->driver_data = i2c_match_id(cy8c95x0_id, client)->driver_data;
|
|
if (!chip->driver_data)
|
|
return -ENODEV;
|
|
|
|
i2c_set_clientdata(client, chip);
|
|
|
|
chip->tpin = chip->driver_data & CY8C95X0_GPIO_MASK;
|
|
chip->nport = DIV_ROUND_UP(CY8C95X0_PIN_TO_OFFSET(chip->tpin), BANK_SZ);
|
|
|
|
switch (chip->tpin) {
|
|
case 20:
|
|
strscpy(chip->name, cy8c95x0_id[0].name, I2C_NAME_SIZE);
|
|
break;
|
|
case 40:
|
|
strscpy(chip->name, cy8c95x0_id[1].name, I2C_NAME_SIZE);
|
|
break;
|
|
case 60:
|
|
strscpy(chip->name, cy8c95x0_id[2].name, I2C_NAME_SIZE);
|
|
break;
|
|
default:
|
|
return -ENODEV;
|
|
}
|
|
|
|
reg = devm_regulator_get(&client->dev, "vdd");
|
|
if (IS_ERR(reg)) {
|
|
if (PTR_ERR(reg) == -EPROBE_DEFER)
|
|
return -EPROBE_DEFER;
|
|
} else {
|
|
ret = regulator_enable(reg);
|
|
if (ret) {
|
|
dev_err(&client->dev, "failed to enable regulator vdd: %d\n", ret);
|
|
return ret;
|
|
}
|
|
chip->regulator = reg;
|
|
}
|
|
|
|
chip->regmap = devm_regmap_init_i2c(client, &cy8c95x0_i2c_regmap);
|
|
if (IS_ERR(chip->regmap)) {
|
|
ret = PTR_ERR(chip->regmap);
|
|
goto err_exit;
|
|
}
|
|
|
|
bitmap_zero(chip->push_pull, MAX_LINE);
|
|
bitmap_zero(chip->shiftmask, MAX_LINE);
|
|
bitmap_set(chip->shiftmask, 0, 20);
|
|
mutex_init(&chip->i2c_lock);
|
|
|
|
if (dmi_first_match(cy8c95x0_dmi_acpi_irq_info)) {
|
|
ret = cy8c95x0_acpi_get_irq(&client->dev);
|
|
if (ret > 0)
|
|
client->irq = ret;
|
|
}
|
|
|
|
if (client->irq) {
|
|
ret = cy8c95x0_irq_setup(chip, client->irq);
|
|
if (ret)
|
|
goto err_exit;
|
|
}
|
|
|
|
ret = cy8c95x0_setup_pinctrl(chip);
|
|
if (ret)
|
|
goto err_exit;
|
|
|
|
ret = cy8c95x0_setup_gpiochip(chip);
|
|
if (ret)
|
|
goto err_exit;
|
|
|
|
return 0;
|
|
|
|
err_exit:
|
|
if (!IS_ERR_OR_NULL(chip->regulator))
|
|
regulator_disable(chip->regulator);
|
|
return ret;
|
|
}
|
|
|
|
static void cy8c95x0_remove(struct i2c_client *client)
|
|
{
|
|
struct cy8c95x0_pinctrl *chip = i2c_get_clientdata(client);
|
|
|
|
if (!IS_ERR_OR_NULL(chip->regulator))
|
|
regulator_disable(chip->regulator);
|
|
}
|
|
|
|
static const struct acpi_device_id cy8c95x0_acpi_ids[] = {
|
|
{ "INT3490", 40, },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(acpi, cy8c95x0_acpi_ids);
|
|
|
|
static struct i2c_driver cy8c95x0_driver = {
|
|
.driver = {
|
|
.name = "cy8c95x0-pinctrl",
|
|
.of_match_table = cy8c95x0_dt_ids,
|
|
.acpi_match_table = cy8c95x0_acpi_ids,
|
|
},
|
|
.probe_new = cy8c95x0_probe,
|
|
.remove = cy8c95x0_remove,
|
|
.id_table = cy8c95x0_id,
|
|
.detect = cy8c95x0_detect,
|
|
};
|
|
module_i2c_driver(cy8c95x0_driver);
|
|
|
|
MODULE_AUTHOR("Patrick Rudolph <patrick.rudolph@9elements.com>");
|
|
MODULE_AUTHOR("Naresh Solanki <naresh.solanki@9elements.com>");
|
|
MODULE_DESCRIPTION("Pinctrl driver for CY8C95X0");
|
|
MODULE_LICENSE("GPL");
|