linux/drivers/input/misc/kxtj9.c

// SPDX-License-Identifier: GPL-2.0-only
/*
 * Copyright (C) 2011 Kionix, Inc.
 * Written by Chris Hudson <chudson@kionix.com>
 */

#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/input/kxtj9.h>

#define NAME			"kxtj9"
#define G_MAX			8000
/* OUTPUT REGISTERS */
#define XOUT_L			0x06
#define WHO_AM_I		0x0F
/* CONTROL REGISTERS */
#define INT_REL			0x1A
#define CTRL_REG1		0x1B
#define INT_CTRL1		0x1E
#define DATA_CTRL		0x21
/* CONTROL REGISTER 1 BITS */
#define PC1_OFF			0x7F
#define PC1_ON			(1 << 7)
/* Data ready funtion enable bit: set during probe if using irq mode */
#define DRDYE			(1 << 5)
/* DATA CONTROL REGISTER BITS */
#define ODR12_5F		0
#define ODR25F			1
#define ODR50F			2
#define ODR100F		3
#define ODR200F		4
#define ODR400F		5
#define ODR800F		6
/* INTERRUPT CONTROL REGISTER 1 BITS */
/* Set these during probe if using irq mode */
#define KXTJ9_IEL		(1 << 3)
#define KXTJ9_IEA		(1 << 4)
#define KXTJ9_IEN		(1 << 5)
/* INPUT_ABS CONSTANTS */
#define FUZZ			3
#define FLAT			3
/* RESUME STATE INDICES */
#define RES_DATA_CTRL		0
#define RES_CTRL_REG1		1
#define RES_INT_CTRL1		2
#define RESUME_ENTRIES		3

/*
 * The following table lists the maximum appropriate poll interval for each
 * available output data rate.
 */
static const struct {
	unsigned int cutoff;
	u8 mask;
} kxtj9_odr_table[] = {
	{ 3,	ODR800F },
	{ 5,	ODR400F },
	{ 10,	ODR200F },
	{ 20,	ODR100F },
	{ 40,	ODR50F  },
	{ 80,	ODR25F  },
	{ 0,	ODR12_5F},
};

struct kxtj9_data {
	struct i2c_client *client;
	struct kxtj9_platform_data pdata;
	struct input_dev *input_dev;
	unsigned int last_poll_interval;
	u8 shift;
	u8 ctrl_reg1;
	u8 data_ctrl;
	u8 int_ctrl;
};

static int kxtj9_i2c_read(struct kxtj9_data *tj9, u8 addr, u8 *data, int len)
{
	struct i2c_msg msgs[] = {
		{
			.addr = tj9->client->addr,
			.flags = tj9->client->flags,
			.len = 1,
			.buf = &addr,
		},
		{
			.addr = tj9->client->addr,
			.flags = tj9->client->flags | I2C_M_RD,
			.len = len,
			.buf = data,
		},
	};

	return i2c_transfer(tj9->client->adapter, msgs, 2);
}

static void kxtj9_report_acceleration_data(struct kxtj9_data *tj9)
{
	s16 acc_data[3]; /* Data bytes from hardware xL, xH, yL, yH, zL, zH */
	s16 x, y, z;
	int err;

	err = kxtj9_i2c_read(tj9, XOUT_L, (u8 *)acc_data, 6);
	if (err < 0)
		dev_err(&tj9->client->dev, "accelerometer data read failed\n");

	x = le16_to_cpu(acc_data[tj9->pdata.axis_map_x]);
	y = le16_to_cpu(acc_data[tj9->pdata.axis_map_y]);
	z = le16_to_cpu(acc_data[tj9->pdata.axis_map_z]);

	x >>= tj9->shift;
	y >>= tj9->shift;
	z >>= tj9->shift;

	input_report_abs(tj9->input_dev, ABS_X, tj9->pdata.negate_x ? -x : x);
	input_report_abs(tj9->input_dev, ABS_Y, tj9->pdata.negate_y ? -y : y);
	input_report_abs(tj9->input_dev, ABS_Z, tj9->pdata.negate_z ? -z : z);
	input_sync(tj9->input_dev);
}

static irqreturn_t kxtj9_isr(int irq, void *dev)
{
	struct kxtj9_data *tj9 = dev;
	int err;

	/* data ready is the only possible interrupt type */
	kxtj9_report_acceleration_data(tj9);

	err = i2c_smbus_read_byte_data(tj9->client, INT_REL);
	if (err < 0)
		dev_err(&tj9->client->dev,
			"error clearing interrupt status: %d\n", err);

	return IRQ_HANDLED;
}

static int kxtj9_update_g_range(struct kxtj9_data *tj9, u8 new_g_range)
{
	switch (new_g_range) {
	case KXTJ9_G_2G:
		tj9->shift = 4;
		break;
	case KXTJ9_G_4G:
		tj9->shift = 3;
		break;
	case KXTJ9_G_8G:
		tj9->shift = 2;
		break;
	default:
		return -EINVAL;
	}

	tj9->ctrl_reg1 &= 0xe7;
	tj9->ctrl_reg1 |= new_g_range;

	return 0;
}

static int kxtj9_update_odr(struct kxtj9_data *tj9, unsigned int poll_interval)
{
	int err;
	int i;

	/* Use the lowest ODR that can support the requested poll interval */
	for (i = 0; i < ARRAY_SIZE(kxtj9_odr_table); i++) {
		tj9->data_ctrl = kxtj9_odr_table[i].mask;
		if (poll_interval < kxtj9_odr_table[i].cutoff)
			break;
	}

	err = i2c_smbus_write_byte_data(tj9->client, CTRL_REG1, 0);
	if (err < 0)
		return err;

	err = i2c_smbus_write_byte_data(tj9->client, DATA_CTRL, tj9->data_ctrl);
	if (err < 0)
		return err;

	err = i2c_smbus_write_byte_data(tj9->client, CTRL_REG1, tj9->ctrl_reg1);
	if (err < 0)
		return err;

	return 0;
}

static int kxtj9_device_power_on(struct kxtj9_data *tj9)
{
	if (tj9->pdata.power_on)
		return tj9->pdata.power_on();

	return 0;
}

static void kxtj9_device_power_off(struct kxtj9_data *tj9)
{
	int err;

	tj9->ctrl_reg1 &= PC1_OFF;
	err = i2c_smbus_write_byte_data(tj9->client, CTRL_REG1, tj9->ctrl_reg1);
	if (err < 0)
		dev_err(&tj9->client->dev, "soft power off failed\n");

	if (tj9->pdata.power_off)
		tj9->pdata.power_off();
}

static int kxtj9_enable(struct kxtj9_data *tj9)
{
	int err;

	err = kxtj9_device_power_on(tj9);
	if (err < 0)
		return err;

	/* ensure that PC1 is cleared before updating control registers */
	err = i2c_smbus_write_byte_data(tj9->client, CTRL_REG1, 0);
	if (err < 0)
		return err;

	/* only write INT_CTRL_REG1 if in irq mode */
	if (tj9->client->irq) {
		err = i2c_smbus_write_byte_data(tj9->client,
						INT_CTRL1, tj9->int_ctrl);
		if (err < 0)
			return err;
	}

	err = kxtj9_update_g_range(tj9, tj9->pdata.g_range);
	if (err < 0)
		return err;

	/* turn on outputs */
	tj9->ctrl_reg1 |= PC1_ON;
	err = i2c_smbus_write_byte_data(tj9->client, CTRL_REG1, tj9->ctrl_reg1);
	if (err < 0)
		return err;

	err = kxtj9_update_odr(tj9, tj9->last_poll_interval);
	if (err < 0)
		return err;

	/* clear initial interrupt if in irq mode */
	if (tj9->client->irq) {
		err = i2c_smbus_read_byte_data(tj9->client, INT_REL);
		if (err < 0) {
			dev_err(&tj9->client->dev,
				"error clearing interrupt: %d\n", err);
			goto fail;
		}
	}

	return 0;

fail:
	kxtj9_device_power_off(tj9);
	return err;
}

static void kxtj9_disable(struct kxtj9_data *tj9)
{
	kxtj9_device_power_off(tj9);
}

static int kxtj9_input_open(struct input_dev *input)
{
	struct kxtj9_data *tj9 = input_get_drvdata(input);

	return kxtj9_enable(tj9);
}

static void kxtj9_input_close(struct input_dev *dev)
{
	struct kxtj9_data *tj9 = input_get_drvdata(dev);

	kxtj9_disable(tj9);
}

/*
 * When IRQ mode is selected, we need to provide an interface to allow the user
 * to change the output data rate of the part.  For consistency, we are using
 * the set_poll method, which accepts a poll interval in milliseconds, and then
 * calls update_odr() while passing this value as an argument.  In IRQ mode, the
 * data outputs will not be read AT the requested poll interval, rather, the
 * lowest ODR that can support the requested interval.  The client application
 * will be responsible for retrieving data from the input node at the desired
 * interval.
 */

/* Returns currently selected poll interval (in ms) */
static ssize_t kxtj9_get_poll(struct device *dev,
				struct device_attribute *attr, char *buf)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct kxtj9_data *tj9 = i2c_get_clientdata(client);

	return sprintf(buf, "%d\n", tj9->last_poll_interval);
}

/* Allow users to select a new poll interval (in ms) */
static ssize_t kxtj9_set_poll(struct device *dev, struct device_attribute *attr,
						const char *buf, size_t count)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct kxtj9_data *tj9 = i2c_get_clientdata(client);
	struct input_dev *input_dev = tj9->input_dev;
	unsigned int interval;
	int error;

	error = kstrtouint(buf, 10, &interval);
	if (error < 0)
		return error;

	/* Lock the device to prevent races with open/close (and itself) */
	mutex_lock(&input_dev->mutex);

	disable_irq(client->irq);

	/*
	 * Set current interval to the greater of the minimum interval or
	 * the requested interval
	 */
	tj9->last_poll_interval = max(interval, tj9->pdata.min_interval);

	kxtj9_update_odr(tj9, tj9->last_poll_interval);

	enable_irq(client->irq);
	mutex_unlock(&input_dev->mutex);

	return count;
}

static DEVICE_ATTR(poll, S_IRUGO|S_IWUSR, kxtj9_get_poll, kxtj9_set_poll);

static struct attribute *kxtj9_attributes[] = {
	&dev_attr_poll.attr,
	NULL
};

static struct attribute_group kxtj9_attribute_group = {
	.attrs = kxtj9_attributes
};

static void kxtj9_poll(struct input_dev *input)
{
	struct kxtj9_data *tj9 = input_get_drvdata(input);
	unsigned int poll_interval = input_get_poll_interval(input);

	kxtj9_report_acceleration_data(tj9);

	if (poll_interval != tj9->last_poll_interval) {
		kxtj9_update_odr(tj9, poll_interval);
		tj9->last_poll_interval = poll_interval;
	}
}

static void kxtj9_platform_exit(void *data)
{
	struct kxtj9_data *tj9 = data;

	if (tj9->pdata.exit)
		tj9->pdata.exit();
}

static int kxtj9_verify(struct kxtj9_data *tj9)
{
	int retval;

	retval = kxtj9_device_power_on(tj9);
	if (retval < 0)
		return retval;

	retval = i2c_smbus_read_byte_data(tj9->client, WHO_AM_I);
	if (retval < 0) {
		dev_err(&tj9->client->dev, "read err int source\n");
		goto out;
	}

	retval = (retval != 0x07 && retval != 0x08) ? -EIO : 0;

out:
	kxtj9_device_power_off(tj9);
	return retval;
}

static int kxtj9_probe(struct i2c_client *client)
{
	const struct kxtj9_platform_data *pdata =
			dev_get_platdata(&client->dev);
	struct kxtj9_data *tj9;
	struct input_dev *input_dev;
	int err;

	if (!i2c_check_functionality(client->adapter,
				I2C_FUNC_I2C | I2C_FUNC_SMBUS_BYTE_DATA)) {
		dev_err(&client->dev, "client is not i2c capable\n");
		return -ENXIO;
	}

	if (!pdata) {
		dev_err(&client->dev, "platform data is NULL; exiting\n");
		return -EINVAL;
	}

	tj9 = devm_kzalloc(&client->dev, sizeof(*tj9), GFP_KERNEL);
	if (!tj9) {
		dev_err(&client->dev,
			"failed to allocate memory for module data\n");
		return -ENOMEM;
	}

	tj9->client = client;
	tj9->pdata = *pdata;

	if (pdata->init) {
		err = pdata->init();
		if (err < 0)
			return err;
	}

	err = devm_add_action_or_reset(&client->dev, kxtj9_platform_exit, tj9);
	if (err)
		return err;

	err = kxtj9_verify(tj9);
	if (err < 0) {
		dev_err(&client->dev, "device not recognized\n");
		return err;
	}

	i2c_set_clientdata(client, tj9);

	tj9->ctrl_reg1 = tj9->pdata.res_12bit | tj9->pdata.g_range;
	tj9->last_poll_interval = tj9->pdata.init_interval;

	input_dev = devm_input_allocate_device(&client->dev);
	if (!input_dev) {
		dev_err(&client->dev, "input device allocate failed\n");
		return -ENOMEM;
	}

	input_set_drvdata(input_dev, tj9);
	tj9->input_dev = input_dev;

	input_dev->name = "kxtj9_accel";
	input_dev->id.bustype = BUS_I2C;

	input_dev->open = kxtj9_input_open;
	input_dev->close = kxtj9_input_close;

	input_set_abs_params(input_dev, ABS_X, -G_MAX, G_MAX, FUZZ, FLAT);
	input_set_abs_params(input_dev, ABS_Y, -G_MAX, G_MAX, FUZZ, FLAT);
	input_set_abs_params(input_dev, ABS_Z, -G_MAX, G_MAX, FUZZ, FLAT);

	if (client->irq <= 0) {
		err = input_setup_polling(input_dev, kxtj9_poll);
		if (err)
			return err;
	}

	err = input_register_device(input_dev);
	if (err) {
		dev_err(&client->dev,
			"unable to register input polled device %s: %d\n",
			input_dev->name, err);
		return err;
	}

	if (client->irq) {
		/* If in irq mode, populate INT_CTRL_REG1 and enable DRDY. */
		tj9->int_ctrl |= KXTJ9_IEN | KXTJ9_IEA | KXTJ9_IEL;
		tj9->ctrl_reg1 |= DRDYE;

		err = devm_request_threaded_irq(&client->dev, client->irq,
						NULL, kxtj9_isr,
						IRQF_TRIGGER_RISING |
							IRQF_ONESHOT,
						"kxtj9-irq", tj9);
		if (err) {
			dev_err(&client->dev, "request irq failed: %d\n", err);
			return err;
		}

		err = devm_device_add_group(&client->dev,
					    &kxtj9_attribute_group);
		if (err) {
			dev_err(&client->dev, "sysfs create failed: %d\n", err);
			return err;
		}
	}

	return 0;
}

static int kxtj9_suspend(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct kxtj9_data *tj9 = i2c_get_clientdata(client);
	struct input_dev *input_dev = tj9->input_dev;

	mutex_lock(&input_dev->mutex);

	if (input_device_enabled(input_dev))
		kxtj9_disable(tj9);

	mutex_unlock(&input_dev->mutex);
	return 0;
}

static int kxtj9_resume(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct kxtj9_data *tj9 = i2c_get_clientdata(client);
	struct input_dev *input_dev = tj9->input_dev;

	mutex_lock(&input_dev->mutex);

	if (input_device_enabled(input_dev))
		kxtj9_enable(tj9);

	mutex_unlock(&input_dev->mutex);
	return 0;
}

static DEFINE_SIMPLE_DEV_PM_OPS(kxtj9_pm_ops, kxtj9_suspend, kxtj9_resume);

static const struct i2c_device_id kxtj9_id[] = {
	{ NAME, 0 },
	{ },
};

MODULE_DEVICE_TABLE(i2c, kxtj9_id);

static struct i2c_driver kxtj9_driver = {
	.driver = {
		.name	= NAME,
		.pm	= pm_sleep_ptr(&kxtj9_pm_ops),
	},
	.probe		= kxtj9_probe,
	.id_table	= kxtj9_id,
};

module_i2c_driver(kxtj9_driver);

MODULE_DESCRIPTION("KXTJ9 accelerometer driver");
MODULE_AUTHOR("Chris Hudson <chudson@kionix.com>");
MODULE_LICENSE("GPL");