mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-17 01:04:19 +08:00
08a0a4f987
Maxim Integrated MAX3355E chip integrates a charge pump and comparators to enable a system with an integrated USB OTG dual-role transceiver to function as an USB OTG dual-role device. In addition to sensing/controlling Vbus, the chip also passes thru the ID signal from the USB OTG connector. On some Renesas boards, this signal is just fed into the SoC thru a GPIO pin -- there's no real OTG controller, only host and gadget USB controllers sharing the same USB bus; however, we'd like to allow host or gadget drivers to be loaded depending on the cable type, hence the need for the MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs (however, we aren't currently interested in them), the OFFVBUS# signal is controlled by the host controllers, there's also the SHDN# signal wired to a GPIO, it should be driven high for the normal operation. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Rob Herring <robh@kernel.org> [cw00.choi: Add the GPIOLIB dependency] Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
130 lines
4.0 KiB
Plaintext
130 lines
4.0 KiB
Plaintext
menuconfig EXTCON
|
|
tristate "External Connector Class (extcon) support"
|
|
help
|
|
Say Y here to enable external connector class (extcon) support.
|
|
This allows monitoring external connectors by userspace
|
|
via sysfs and uevent and supports external connectors with
|
|
multiple states; i.e., an extcon that may have multiple
|
|
cables attached. For example, an external connector of a device
|
|
may be used to connect an HDMI cable and a AC adaptor, and to
|
|
host USB ports. Many of 30-pin connectors including PDMI are
|
|
also good examples.
|
|
|
|
if EXTCON
|
|
|
|
comment "Extcon Device Drivers"
|
|
|
|
config EXTCON_ADC_JACK
|
|
tristate "ADC Jack extcon support"
|
|
depends on IIO
|
|
help
|
|
Say Y here to enable extcon device driver based on ADC values.
|
|
|
|
config EXTCON_ARIZONA
|
|
tristate "Wolfson Arizona EXTCON support"
|
|
depends on MFD_ARIZONA && INPUT && SND_SOC
|
|
help
|
|
Say Y here to enable support for external accessory detection
|
|
with Wolfson Arizona devices. These are audio CODECs with
|
|
advanced audio accessory detection support.
|
|
|
|
config EXTCON_AXP288
|
|
tristate "X-Power AXP288 EXTCON support"
|
|
depends on MFD_AXP20X && USB_PHY
|
|
help
|
|
Say Y here to enable support for USB peripheral detection
|
|
and USB MUX switching by X-Power AXP288 PMIC.
|
|
|
|
config EXTCON_GPIO
|
|
tristate "GPIO extcon support"
|
|
depends on GPIOLIB || COMPILE_TEST
|
|
help
|
|
Say Y here to enable GPIO based extcon support. Note that GPIO
|
|
extcon supports single state per extcon instance.
|
|
|
|
config EXTCON_MAX14577
|
|
tristate "Maxim MAX14577/77836 EXTCON Support"
|
|
depends on MFD_MAX14577
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX14577/77836. The MAX14577/77836 MUIC is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_MAX3355
|
|
tristate "Maxim MAX3355 USB OTG EXTCON Support"
|
|
depends on GPIOLIB || COMPILE_TEST
|
|
help
|
|
If you say yes here you get support for the USB OTG role detection by
|
|
MAX3355. The MAX3355 chip integrates a charge pump and comparators to
|
|
enable a system with an integrated USB OTG dual-role transceiver to
|
|
function as an USB OTG dual-role device.
|
|
|
|
config EXTCON_MAX77693
|
|
tristate "Maxim MAX77693 EXTCON Support"
|
|
depends on MFD_MAX77693 && INPUT
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX77693 PMIC. The MAX77693 MUIC is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_MAX77843
|
|
tristate "Maxim MAX77843 EXTCON Support"
|
|
depends on MFD_MAX77843
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX77843. The MAX77843 MUIC is a USB port accessory
|
|
detector add switch.
|
|
|
|
config EXTCON_MAX8997
|
|
tristate "Maxim MAX8997 EXTCON Support"
|
|
depends on MFD_MAX8997 && IRQ_DOMAIN
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX8997 PMIC. The MAX8997 MUIC is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_PALMAS
|
|
tristate "Palmas USB EXTCON support"
|
|
depends on MFD_PALMAS
|
|
help
|
|
Say Y here to enable support for USB peripheral and USB host
|
|
detection by palmas usb.
|
|
|
|
config EXTCON_RT8973A
|
|
tristate "Richtek RT8973A EXTCON support"
|
|
depends on I2C
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
select REGMAP_IRQ
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Richtek RT8973A. The RT8973A is a USB port accessory detector
|
|
and switch that is optimized to protect low voltage system
|
|
from abnormal high input voltage (up to 28V).
|
|
|
|
config EXTCON_SM5502
|
|
tristate "Silicon Mitus SM5502 EXTCON support"
|
|
depends on I2C
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
select REGMAP_IRQ
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Silicon Mitus SM5502. The SM5502 is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_USB_GPIO
|
|
tristate "USB GPIO extcon support"
|
|
depends on GPIOLIB || COMPILE_TEST
|
|
help
|
|
Say Y here to enable GPIO based USB cable detection extcon support.
|
|
Used typically if GPIO is used for USB ID pin detection.
|
|
|
|
endif
|