mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-06 02:24:14 +08:00
edb9a1b894
Signed-off-by: Eric Engestrom <eric@engestrom.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
264 lines
12 KiB
Plaintext
264 lines
12 KiB
Plaintext
Altera Triple-Speed Ethernet MAC driver
|
|
|
|
Copyright (C) 2008-2014 Altera Corporation
|
|
|
|
This is the driver for the Altera Triple-Speed Ethernet (TSE) controllers
|
|
using the SGDMA and MSGDMA soft DMA IP components. The driver uses the
|
|
platform bus to obtain component resources. The designs used to test this
|
|
driver were built for a Cyclone(R) V SOC FPGA board, a Cyclone(R) V FPGA board,
|
|
and tested with ARM and NIOS processor hosts separately. The anticipated use
|
|
cases are simple communications between an embedded system and an external peer
|
|
for status and simple configuration of the embedded system.
|
|
|
|
For more information visit www.altera.com and www.rocketboards.org. Support
|
|
forums for the driver may be found on www.rocketboards.org, and a design used
|
|
to test this driver may be found there as well. Support is also available from
|
|
the maintainer of this driver, found in MAINTAINERS.
|
|
|
|
The Triple-Speed Ethernet, SGDMA, and MSGDMA components are all soft IP
|
|
components that can be assembled and built into an FPGA using the Altera
|
|
Quartus toolchain. Quartus 13.1 and 14.0 were used to build the design that
|
|
this driver was tested against. The sopc2dts tool is used to create the
|
|
device tree for the driver, and may be found at rocketboards.org.
|
|
|
|
The driver probe function examines the device tree and determines if the
|
|
Triple-Speed Ethernet instance is using an SGDMA or MSGDMA component. The
|
|
probe function then installs the appropriate set of DMA routines to
|
|
initialize, setup transmits, receives, and interrupt handling primitives for
|
|
the respective configurations.
|
|
|
|
The SGDMA component is to be deprecated in the near future (over the next 1-2
|
|
years as of this writing in early 2014) in favor of the MSGDMA component.
|
|
SGDMA support is included for existing designs and reference in case a
|
|
developer wishes to support their own soft DMA logic and driver support. Any
|
|
new designs should not use the SGDMA.
|
|
|
|
The SGDMA supports only a single transmit or receive operation at a time, and
|
|
therefore will not perform as well compared to the MSGDMA soft IP. Please
|
|
visit www.altera.com for known, documented SGDMA errata.
|
|
|
|
Scatter-gather DMA is not supported by the SGDMA or MSGDMA at this time.
|
|
Scatter-gather DMA will be added to a future maintenance update to this
|
|
driver.
|
|
|
|
Jumbo frames are not supported at this time.
|
|
|
|
The driver limits PHY operations to 10/100Mbps, and has not yet been fully
|
|
tested for 1Gbps. This support will be added in a future maintenance update.
|
|
|
|
1) Kernel Configuration
|
|
The kernel configuration option is ALTERA_TSE:
|
|
Device Drivers ---> Network device support ---> Ethernet driver support --->
|
|
Altera Triple-Speed Ethernet MAC support (ALTERA_TSE)
|
|
|
|
2) Driver parameters list:
|
|
debug: message level (0: no output, 16: all);
|
|
dma_rx_num: Number of descriptors in the RX list (default is 64);
|
|
dma_tx_num: Number of descriptors in the TX list (default is 64).
|
|
|
|
3) Command line options
|
|
Driver parameters can be also passed in command line by using:
|
|
altera_tse=dma_rx_num:128,dma_tx_num:512
|
|
|
|
4) Driver information and notes
|
|
|
|
4.1) Transmit process
|
|
When the driver's transmit routine is called by the kernel, it sets up a
|
|
transmit descriptor by calling the underlying DMA transmit routine (SGDMA or
|
|
MSGDMA), and initiates a transmit operation. Once the transmit is complete, an
|
|
interrupt is driven by the transmit DMA logic. The driver handles the transmit
|
|
completion in the context of the interrupt handling chain by recycling
|
|
resource required to send and track the requested transmit operation.
|
|
|
|
4.2) Receive process
|
|
The driver will post receive buffers to the receive DMA logic during driver
|
|
initialization. Receive buffers may or may not be queued depending upon the
|
|
underlying DMA logic (MSGDMA is able queue receive buffers, SGDMA is not able
|
|
to queue receive buffers to the SGDMA receive logic). When a packet is
|
|
received, the DMA logic generates an interrupt. The driver handles a receive
|
|
interrupt by obtaining the DMA receive logic status, reaping receive
|
|
completions until no more receive completions are available.
|
|
|
|
4.3) Interrupt Mitigation
|
|
The driver is able to mitigate the number of its DMA interrupts
|
|
using NAPI for receive operations. Interrupt mitigation is not yet supported
|
|
for transmit operations, but will be added in a future maintenance release.
|
|
|
|
4.4) Ethtool support
|
|
Ethtool is supported. Driver statistics and internal errors can be taken using:
|
|
ethtool -S ethX command. It is possible to dump registers etc.
|
|
|
|
4.5) PHY Support
|
|
The driver is compatible with PAL to work with PHY and GPHY devices.
|
|
|
|
4.7) List of source files:
|
|
o Kconfig
|
|
o Makefile
|
|
o altera_tse_main.c: main network device driver
|
|
o altera_tse_ethtool.c: ethtool support
|
|
o altera_tse.h: private driver structure and common definitions
|
|
o altera_msgdma.h: MSGDMA implementation function definitions
|
|
o altera_sgdma.h: SGDMA implementation function definitions
|
|
o altera_msgdma.c: MSGDMA implementation
|
|
o altera_sgdma.c: SGDMA implementation
|
|
o altera_sgdmahw.h: SGDMA register and descriptor definitions
|
|
o altera_msgdmahw.h: MSGDMA register and descriptor definitions
|
|
o altera_utils.c: Driver utility functions
|
|
o altera_utils.h: Driver utility function definitions
|
|
|
|
5) Debug Information
|
|
|
|
The driver exports debug information such as internal statistics,
|
|
debug information, MAC and DMA registers etc.
|
|
|
|
A user may use the ethtool support to get statistics:
|
|
e.g. using: ethtool -S ethX (that shows the statistics counters)
|
|
or sees the MAC registers: e.g. using: ethtool -d ethX
|
|
|
|
The developer can also use the "debug" module parameter to get
|
|
further debug information.
|
|
|
|
6) Statistics Support
|
|
|
|
The controller and driver support a mix of IEEE standard defined statistics,
|
|
RFC defined statistics, and driver or Altera defined statistics. The four
|
|
specifications containing the standard definitions for these statistics are
|
|
as follows:
|
|
|
|
o IEEE 802.3-2012 - IEEE Standard for Ethernet.
|
|
o RFC 2863 found at http://www.rfc-editor.org/rfc/rfc2863.txt.
|
|
o RFC 2819 found at http://www.rfc-editor.org/rfc/rfc2819.txt.
|
|
o Altera Triple Speed Ethernet User Guide, found at http://www.altera.com
|
|
|
|
The statistics supported by the TSE and the device driver are as follows:
|
|
|
|
"tx_packets" is equivalent to aFramesTransmittedOK defined in IEEE 802.3-2012,
|
|
Section 5.2.2.1.2. This statistics is the count of frames that are successfully
|
|
transmitted.
|
|
|
|
"rx_packets" is equivalent to aFramesReceivedOK defined in IEEE 802.3-2012,
|
|
Section 5.2.2.1.5. This statistic is the count of frames that are successfully
|
|
received. This count does not include any error packets such as CRC errors,
|
|
length errors, or alignment errors.
|
|
|
|
"rx_crc_errors" is equivalent to aFrameCheckSequenceErrors defined in IEEE
|
|
802.3-2012, Section 5.2.2.1.6. This statistic is the count of frames that are
|
|
an integral number of bytes in length and do not pass the CRC test as the frame
|
|
is received.
|
|
|
|
"rx_align_errors" is equivalent to aAlignmentErrors defined in IEEE 802.3-2012,
|
|
Section 5.2.2.1.7. This statistic is the count of frames that are not an
|
|
integral number of bytes in length and do not pass the CRC test as the frame is
|
|
received.
|
|
|
|
"tx_bytes" is equivalent to aOctetsTransmittedOK defined in IEEE 802.3-2012,
|
|
Section 5.2.2.1.8. This statistic is the count of data and pad bytes
|
|
successfully transmitted from the interface.
|
|
|
|
"rx_bytes" is equivalent to aOctetsReceivedOK defined in IEEE 802.3-2012,
|
|
Section 5.2.2.1.14. This statistic is the count of data and pad bytes
|
|
successfully received by the controller.
|
|
|
|
"tx_pause" is equivalent to aPAUSEMACCtrlFramesTransmitted defined in IEEE
|
|
802.3-2012, Section 30.3.4.2. This statistic is a count of PAUSE frames
|
|
transmitted from the network controller.
|
|
|
|
"rx_pause" is equivalent to aPAUSEMACCtrlFramesReceived defined in IEEE
|
|
802.3-2012, Section 30.3.4.3. This statistic is a count of PAUSE frames
|
|
received by the network controller.
|
|
|
|
"rx_errors" is equivalent to ifInErrors defined in RFC 2863. This statistic is
|
|
a count of the number of packets received containing errors that prevented the
|
|
packet from being delivered to a higher level protocol.
|
|
|
|
"tx_errors" is equivalent to ifOutErrors defined in RFC 2863. This statistic
|
|
is a count of the number of packets that could not be transmitted due to errors.
|
|
|
|
"rx_unicast" is equivalent to ifInUcastPkts defined in RFC 2863. This
|
|
statistic is a count of the number of packets received that were not addressed
|
|
to the broadcast address or a multicast group.
|
|
|
|
"rx_multicast" is equivalent to ifInMulticastPkts defined in RFC 2863. This
|
|
statistic is a count of the number of packets received that were addressed to
|
|
a multicast address group.
|
|
|
|
"rx_broadcast" is equivalent to ifInBroadcastPkts defined in RFC 2863. This
|
|
statistic is a count of the number of packets received that were addressed to
|
|
the broadcast address.
|
|
|
|
"tx_discards" is equivalent to ifOutDiscards defined in RFC 2863. This
|
|
statistic is the number of outbound packets not transmitted even though an
|
|
error was not detected. An example of a reason this might occur is to free up
|
|
internal buffer space.
|
|
|
|
"tx_unicast" is equivalent to ifOutUcastPkts defined in RFC 2863. This
|
|
statistic counts the number of packets transmitted that were not addressed to
|
|
a multicast group or broadcast address.
|
|
|
|
"tx_multicast" is equivalent to ifOutMulticastPkts defined in RFC 2863. This
|
|
statistic counts the number of packets transmitted that were addressed to a
|
|
multicast group.
|
|
|
|
"tx_broadcast" is equivalent to ifOutBroadcastPkts defined in RFC 2863. This
|
|
statistic counts the number of packets transmitted that were addressed to a
|
|
broadcast address.
|
|
|
|
"ether_drops" is equivalent to etherStatsDropEvents defined in RFC 2819.
|
|
This statistic counts the number of packets dropped due to lack of internal
|
|
controller resources.
|
|
|
|
"rx_total_bytes" is equivalent to etherStatsOctets defined in RFC 2819.
|
|
This statistic counts the total number of bytes received by the controller,
|
|
including error and discarded packets.
|
|
|
|
"rx_total_packets" is equivalent to etherStatsPkts defined in RFC 2819.
|
|
This statistic counts the total number of packets received by the controller,
|
|
including error, discarded, unicast, multicast, and broadcast packets.
|
|
|
|
"rx_undersize" is equivalent to etherStatsUndersizePkts defined in RFC 2819.
|
|
This statistic counts the number of correctly formed packets received less
|
|
than 64 bytes long.
|
|
|
|
"rx_oversize" is equivalent to etherStatsOversizePkts defined in RFC 2819.
|
|
This statistic counts the number of correctly formed packets greater than 1518
|
|
bytes long.
|
|
|
|
"rx_64_bytes" is equivalent to etherStatsPkts64Octets defined in RFC 2819.
|
|
This statistic counts the total number of packets received that were 64 octets
|
|
in length.
|
|
|
|
"rx_65_127_bytes" is equivalent to etherStatsPkts65to127Octets defined in RFC
|
|
2819. This statistic counts the total number of packets received that were
|
|
between 65 and 127 octets in length inclusive.
|
|
|
|
"rx_128_255_bytes" is equivalent to etherStatsPkts128to255Octets defined in
|
|
RFC 2819. This statistic is the total number of packets received that were
|
|
between 128 and 255 octets in length inclusive.
|
|
|
|
"rx_256_511_bytes" is equivalent to etherStatsPkts256to511Octets defined in
|
|
RFC 2819. This statistic is the total number of packets received that were
|
|
between 256 and 511 octets in length inclusive.
|
|
|
|
"rx_512_1023_bytes" is equivalent to etherStatsPkts512to1023Octets defined in
|
|
RFC 2819. This statistic is the total number of packets received that were
|
|
between 512 and 1023 octets in length inclusive.
|
|
|
|
"rx_1024_1518_bytes" is equivalent to etherStatsPkts1024to1518Octets define
|
|
in RFC 2819. This statistic is the total number of packets received that were
|
|
between 1024 and 1518 octets in length inclusive.
|
|
|
|
"rx_gte_1519_bytes" is a statistic defined specific to the behavior of the
|
|
Altera TSE. This statistics counts the number of received good and errored
|
|
frames between the length of 1519 and the maximum frame length configured
|
|
in the frm_length register. See the Altera TSE User Guide for More details.
|
|
|
|
"rx_jabbers" is equivalent to etherStatsJabbers defined in RFC 2819. This
|
|
statistic is the total number of packets received that were longer than 1518
|
|
octets, and had either a bad CRC with an integral number of octets (CRC Error)
|
|
or a bad CRC with a non-integral number of octets (Alignment Error).
|
|
|
|
"rx_runts" is equivalent to etherStatsFragments defined in RFC 2819. This
|
|
statistic is the total number of packets received that were less than 64 octets
|
|
in length and had either a bad CRC with an integral number of octets (CRC
|
|
error) or a bad CRC with a non-integral number of octets (Alignment Error).
|