linux/Documentation/media/v4l-drivers/imx.rst

.. SPDX-License-Identifier: GPL-2.0

i.MX Video Capture Driver
=========================

Introduction
------------

The Freescale i.MX5/6 contains an Image Processing Unit (IPU), which
handles the flow of image frames to and from capture devices and
display devices.

For image capture, the IPU contains the following internal subunits:

- Image DMA Controller (IDMAC)
- Camera Serial Interface (CSI)
- Image Converter (IC)
- Sensor Multi-FIFO Controller (SMFC)
- Image Rotator (IRT)
- Video De-Interlacing or Combining Block (VDIC)

The IDMAC is the DMA controller for transfer of image frames to and from
memory. Various dedicated DMA channels exist for both video capture and
display paths. During transfer, the IDMAC is also capable of vertical
image flip, 8x8 block transfer (see IRT description), pixel component
re-ordering (for example UYVY to YUYV) within the same colorspace, and
packed <--> planar conversion. The IDMAC can also perform a simple
de-interlacing by interweaving even and odd lines during transfer
(without motion compensation which requires the VDIC).

The CSI is the backend capture unit that interfaces directly with
camera sensors over Parallel, BT.656/1120, and MIPI CSI-2 buses.

The IC handles color-space conversion, resizing (downscaling and
upscaling), horizontal flip, and 90/270 degree rotation operations.

There are three independent "tasks" within the IC that can carry out
conversions concurrently: pre-process encoding, pre-process viewfinder,
and post-processing. Within each task, conversions are split into three
sections: downsizing section, main section (upsizing, flip, colorspace
conversion, and graphics plane combining), and rotation section.

The IPU time-shares the IC task operations. The time-slice granularity
is one burst of eight pixels in the downsizing section, one image line
in the main processing section, one image frame in the rotation section.

The SMFC is composed of four independent FIFOs that each can transfer
captured frames from sensors directly to memory concurrently via four
IDMAC channels.

The IRT carries out 90 and 270 degree image rotation operations. The
rotation operation is carried out on 8x8 pixel blocks at a time. This
operation is supported by the IDMAC which handles the 8x8 block transfer
along with block reordering, in coordination with vertical flip.

The VDIC handles the conversion of interlaced video to progressive, with
support for different motion compensation modes (low, medium, and high
motion). The deinterlaced output frames from the VDIC can be sent to the
IC pre-process viewfinder task for further conversions. The VDIC also
contains a Combiner that combines two image planes, with alpha blending
and color keying.

In addition to the IPU internal subunits, there are also two units
outside the IPU that are also involved in video capture on i.MX:

- MIPI CSI-2 Receiver for camera sensors with the MIPI CSI-2 bus
  interface. This is a Synopsys DesignWare core.
- Two video multiplexers for selecting among multiple sensor inputs
  to send to a CSI.

For more info, refer to the latest versions of the i.MX5/6 reference
manuals [#f1]_ and [#f2]_.


Features
--------

Some of the features of this driver include:

- Many different pipelines can be configured via media controller API,
  that correspond to the hardware video capture pipelines supported in
  the i.MX.

- Supports parallel, BT.565, and MIPI CSI-2 interfaces.

- Concurrent independent streams, by configuring pipelines to multiple
  video capture interfaces using independent entities.

- Scaling, color-space conversion, horizontal and vertical flip, and
  image rotation via IC task subdevs.

- Many pixel formats supported (RGB, packed and planar YUV, partial
  planar YUV).

- The VDIC subdev supports motion compensated de-interlacing, with three
  motion compensation modes: low, medium, and high motion. Pipelines are
  defined that allow sending frames to the VDIC subdev directly from the
  CSI. There is also support in the future for sending frames to the
  VDIC from memory buffers via a output/mem2mem devices.

- Includes a Frame Interval Monitor (FIM) that can correct vertical sync
  problems with the ADV718x video decoders.


Entities
--------

imx6-mipi-csi2
--------------

This is the MIPI CSI-2 receiver entity. It has one sink pad to receive
the MIPI CSI-2 stream (usually from a MIPI CSI-2 camera sensor). It has
four source pads, corresponding to the four MIPI CSI-2 demuxed virtual
channel outputs. Multiple source pads can be enabled to independently
stream from multiple virtual channels.

This entity actually consists of two sub-blocks. One is the MIPI CSI-2
core. This is a Synopsys Designware MIPI CSI-2 core. The other sub-block
is a "CSI-2 to IPU gasket". The gasket acts as a demultiplexer of the
four virtual channels streams, providing four separate parallel buses
containing each virtual channel that are routed to CSIs or video
multiplexers as described below.

On i.MX6 solo/dual-lite, all four virtual channel buses are routed to
two video multiplexers. Both CSI0 and CSI1 can receive any virtual
channel, as selected by the video multiplexers.

On i.MX6 Quad, virtual channel 0 is routed to IPU1-CSI0 (after selected
by a video mux), virtual channels 1 and 2 are hard-wired to IPU1-CSI1
and IPU2-CSI0, respectively, and virtual channel 3 is routed to
IPU2-CSI1 (again selected by a video mux).

ipuX_csiY_mux
-------------

These are the video multiplexers. They have two or more sink pads to
select from either camera sensors with a parallel interface, or from
MIPI CSI-2 virtual channels from imx6-mipi-csi2 entity. They have a
single source pad that routes to a CSI (ipuX_csiY entities).

On i.MX6 solo/dual-lite, there are two video mux entities. One sits
in front of IPU1-CSI0 to select between a parallel sensor and any of
the four MIPI CSI-2 virtual channels (a total of five sink pads). The
other mux sits in front of IPU1-CSI1, and again has five sink pads to
select between a parallel sensor and any of the four MIPI CSI-2 virtual
channels.

On i.MX6 Quad, there are two video mux entities. One sits in front of
IPU1-CSI0 to select between a parallel sensor and MIPI CSI-2 virtual
channel 0 (two sink pads). The other mux sits in front of IPU2-CSI1 to
select between a parallel sensor and MIPI CSI-2 virtual channel 3 (two
sink pads).

ipuX_csiY
---------

These are the CSI entities. They have a single sink pad receiving from
either a video mux or from a MIPI CSI-2 virtual channel as described
above.

This entity has two source pads. The first source pad can link directly
to the ipuX_vdic entity or the ipuX_ic_prp entity, using hardware links
that require no IDMAC memory buffer transfer.

When the direct source pad is routed to the ipuX_ic_prp entity, frames
from the CSI can be processed by one or both of the IC pre-processing
tasks.

When the direct source pad is routed to the ipuX_vdic entity, the VDIC
will carry out motion-compensated de-interlace using "high motion" mode
(see description of ipuX_vdic entity).

The second source pad sends video frames directly to memory buffers
via the SMFC and an IDMAC channel, bypassing IC pre-processing. This
source pad is routed to a capture device node, with a node name of the
format "ipuX_csiY capture".

Note that since the IDMAC source pad makes use of an IDMAC channel,
pixel reordering within the same colorspace can be carried out by the
IDMAC channel. For example, if the CSI sink pad is receiving in UYVY
order, the capture device linked to the IDMAC source pad can capture
in YUYV order. Also, if the CSI sink pad is receiving a packed YUV
format, the capture device can capture a planar YUV format such as
YUV420.

The IDMAC channel at the IDMAC source pad also supports simple
interweave without motion compensation, which is activated if the source
pad's field type is sequential top-bottom or bottom-top, and the
requested capture interface field type is set to interlaced (t-b, b-t,
or unqualified interlaced). The capture interface will enforce the same
field order as the source pad field order (interlaced-bt if source pad
is seq-bt, interlaced-tb if source pad is seq-tb).

This subdev can generate the following event when enabling the second
IDMAC source pad:

- V4L2_EVENT_IMX_FRAME_INTERVAL_ERROR

The user application can subscribe to this event from the ipuX_csiY
subdev node. This event is generated by the Frame Interval Monitor
(see below for more on the FIM).

Cropping in ipuX_csiY
---------------------

The CSI supports cropping the incoming raw sensor frames. This is
implemented in the ipuX_csiY entities at the sink pad, using the
crop selection subdev API.

The CSI also supports fixed divide-by-two downscaling independently in
width and height. This is implemented in the ipuX_csiY entities at
the sink pad, using the compose selection subdev API.

The output rectangle at the ipuX_csiY source pad is the same as
the compose rectangle at the sink pad. So the source pad rectangle
cannot be negotiated, it must be set using the compose selection
API at sink pad (if /2 downscale is desired, otherwise source pad
rectangle is equal to incoming rectangle).

To give an example of crop and /2 downscale, this will crop a
1280x960 input frame to 640x480, and then /2 downscale in both
dimensions to 320x240 (assumes ipu1_csi0 is linked to ipu1_csi0_mux):

.. code-block:: none

   media-ctl -V "'ipu1_csi0_mux':2[fmt:UYVY2X8/1280x960]"
   media-ctl -V "'ipu1_csi0':0[crop:(0,0)/640x480]"
   media-ctl -V "'ipu1_csi0':0[compose:(0,0)/320x240]"

Frame Skipping in ipuX_csiY
---------------------------

The CSI supports frame rate decimation, via frame skipping. Frame
rate decimation is specified by setting the frame intervals at
sink and source pads. The ipuX_csiY entity then applies the best
frame skip setting to the CSI to achieve the desired frame rate
at the source pad.

The following example reduces an assumed incoming 60 Hz frame
rate by half at the IDMAC output source pad:

.. code-block:: none

   media-ctl -V "'ipu1_csi0':0[fmt:UYVY2X8/640x480@1/60]"
   media-ctl -V "'ipu1_csi0':2[fmt:UYVY2X8/640x480@1/30]"

Frame Interval Monitor in ipuX_csiY
-----------------------------------

The adv718x decoders can occasionally send corrupt fields during
NTSC/PAL signal re-sync (too little or too many video lines). When
this happens, the IPU triggers a mechanism to re-establish vertical
sync by adding 1 dummy line every frame, which causes a rolling effect
from image to image, and can last a long time before a stable image is
recovered. Or sometimes the mechanism doesn't work at all, causing a
permanent split image (one frame contains lines from two consecutive
captured images).

From experiment it was found that during image rolling, the frame
intervals (elapsed time between two EOF's) drop below the nominal
value for the current standard, by about one frame time (60 usec),
and remain at that value until rolling stops.

While the reason for this observation isn't known (the IPU dummy
line mechanism should show an increase in the intervals by 1 line
time every frame, not a fixed value), we can use it to detect the
corrupt fields using a frame interval monitor. If the FIM detects a
bad frame interval, the ipuX_csiY subdev will send the event
V4L2_EVENT_IMX_FRAME_INTERVAL_ERROR. Userland can register with
the FIM event notification on the ipuX_csiY subdev device node.
Userland can issue a streaming restart when this event is received
to correct the rolling/split image.

The ipuX_csiY subdev includes custom controls to tweak some dials for
FIM. If one of these controls is changed during streaming, the FIM will
be reset and will continue at the new settings.

- V4L2_CID_IMX_FIM_ENABLE

Enable/disable the FIM.

- V4L2_CID_IMX_FIM_NUM

How many frame interval measurements to average before comparing against
the nominal frame interval reported by the sensor. This can reduce noise
caused by interrupt latency.

- V4L2_CID_IMX_FIM_TOLERANCE_MIN

If the averaged intervals fall outside nominal by this amount, in
microseconds, the V4L2_EVENT_IMX_FRAME_INTERVAL_ERROR event is sent.

- V4L2_CID_IMX_FIM_TOLERANCE_MAX

If any intervals are higher than this value, those samples are
discarded and do not enter into the average. This can be used to
discard really high interval errors that might be due to interrupt
latency from high system load.

- V4L2_CID_IMX_FIM_NUM_SKIP

How many frames to skip after a FIM reset or stream restart before
FIM begins to average intervals.

- V4L2_CID_IMX_FIM_ICAP_CHANNEL
- V4L2_CID_IMX_FIM_ICAP_EDGE

These controls will configure an input capture channel as the method
for measuring frame intervals. This is superior to the default method
of measuring frame intervals via EOF interrupt, since it is not subject
to uncertainty errors introduced by interrupt latency.

Input capture requires hardware support. A VSYNC signal must be routed
to one of the i.MX6 input capture channel pads.

V4L2_CID_IMX_FIM_ICAP_CHANNEL configures which i.MX6 input capture
channel to use. This must be 0 or 1.

V4L2_CID_IMX_FIM_ICAP_EDGE configures which signal edge will trigger
input capture events. By default the input capture method is disabled
with a value of IRQ_TYPE_NONE. Set this control to IRQ_TYPE_EDGE_RISING,
IRQ_TYPE_EDGE_FALLING, or IRQ_TYPE_EDGE_BOTH to enable input capture,
triggered on the given signal edge(s).

When input capture is disabled, frame intervals will be measured via
EOF interrupt.


ipuX_vdic
---------

The VDIC carries out motion compensated de-interlacing, with three
motion compensation modes: low, medium, and high motion. The mode is
specified with the menu control V4L2_CID_DEINTERLACING_MODE. The VDIC
has two sink pads and a single source pad.

The direct sink pad receives from an ipuX_csiY direct pad. With this
link the VDIC can only operate in high motion mode.

When the IDMAC sink pad is activated, it receives from an output
or mem2mem device node. With this pipeline, the VDIC can also operate
in low and medium modes, because these modes require receiving
frames from memory buffers. Note that an output or mem2mem device
is not implemented yet, so this sink pad currently has no links.

The source pad routes to the IC pre-processing entity ipuX_ic_prp.

ipuX_ic_prp
-----------

This is the IC pre-processing entity. It acts as a router, routing
data from its sink pad to one or both of its source pads.

This entity has a single sink pad. The sink pad can receive from the
ipuX_csiY direct pad, or from ipuX_vdic.

This entity has two source pads. One source pad routes to the
pre-process encode task entity (ipuX_ic_prpenc), the other to the
pre-process viewfinder task entity (ipuX_ic_prpvf). Both source pads
can be activated at the same time if the sink pad is receiving from
ipuX_csiY. Only the source pad to the pre-process viewfinder task entity
can be activated if the sink pad is receiving from ipuX_vdic (frames
from the VDIC can only be processed by the pre-process viewfinder task).

ipuX_ic_prpenc
--------------

This is the IC pre-processing encode entity. It has a single sink
pad from ipuX_ic_prp, and a single source pad. The source pad is
routed to a capture device node, with a node name of the format
"ipuX_ic_prpenc capture".

This entity performs the IC pre-process encode task operations:
color-space conversion, resizing (downscaling and upscaling),
horizontal and vertical flip, and 90/270 degree rotation. Flip
and rotation are provided via standard V4L2 controls.

Like the ipuX_csiY IDMAC source, this entity also supports simple
de-interlace without motion compensation, and pixel reordering.

ipuX_ic_prpvf
-------------

This is the IC pre-processing viewfinder entity. It has a single sink
pad from ipuX_ic_prp, and a single source pad. The source pad is routed
to a capture device node, with a node name of the format
"ipuX_ic_prpvf capture".

This entity is identical in operation to ipuX_ic_prpenc, with the same
resizing and CSC operations and flip/rotation controls. It will receive
and process de-interlaced frames from the ipuX_vdic if ipuX_ic_prp is
receiving from ipuX_vdic.

Like the ipuX_csiY IDMAC source, this entity supports simple
interweaving without motion compensation. However, note that if the
ipuX_vdic is included in the pipeline (ipuX_ic_prp is receiving from
ipuX_vdic), it's not possible to use interweave in ipuX_ic_prpvf,
since the ipuX_vdic has already carried out de-interlacing (with
motion compensation) and therefore the field type output from
ipuX_vdic can only be none (progressive).

Capture Pipelines
-----------------

The following describe the various use-cases supported by the pipelines.

The links shown do not include the backend sensor, video mux, or mipi
csi-2 receiver links. This depends on the type of sensor interface
(parallel or mipi csi-2). So these pipelines begin with:

sensor -> ipuX_csiY_mux -> ...

for parallel sensors, or:

sensor -> imx6-mipi-csi2 -> (ipuX_csiY_mux) -> ...

for mipi csi-2 sensors. The imx6-mipi-csi2 receiver may need to route
to the video mux (ipuX_csiY_mux) before sending to the CSI, depending
on the mipi csi-2 virtual channel, hence ipuX_csiY_mux is shown in
parenthesis.

Unprocessed Video Capture:
--------------------------

Send frames directly from sensor to camera device interface node, with
no conversions, via ipuX_csiY IDMAC source pad:

-> ipuX_csiY:2 -> ipuX_csiY capture

IC Direct Conversions:
----------------------

This pipeline uses the preprocess encode entity to route frames directly
from the CSI to the IC, to carry out scaling up to 1024x1024 resolution,
CSC, flipping, and image rotation:

-> ipuX_csiY:1 -> 0:ipuX_ic_prp:1 -> 0:ipuX_ic_prpenc:1 -> ipuX_ic_prpenc capture

Motion Compensated De-interlace:
--------------------------------

This pipeline routes frames from the CSI direct pad to the VDIC entity to
support motion-compensated de-interlacing (high motion mode only),
scaling up to 1024x1024, CSC, flip, and rotation:

-> ipuX_csiY:1 -> 0:ipuX_vdic:2 -> 0:ipuX_ic_prp:2 -> 0:ipuX_ic_prpvf:1 -> ipuX_ic_prpvf capture


Usage Notes
-----------

To aid in configuration and for backward compatibility with V4L2
applications that access controls only from video device nodes, the
capture device interfaces inherit controls from the active entities
in the current pipeline, so controls can be accessed either directly
from the subdev or from the active capture device interface. For
example, the FIM controls are available either from the ipuX_csiY
subdevs or from the active capture device.

The following are specific usage notes for the Sabre* reference
boards:


SabreLite with OV5642 and OV5640
--------------------------------

This platform requires the OmniVision OV5642 module with a parallel
camera interface, and the OV5640 module with a MIPI CSI-2
interface. Both modules are available from Boundary Devices:

- https://boundarydevices.com/product/nit6x_5mp
- https://boundarydevices.com/product/nit6x_5mp_mipi

Note that if only one camera module is available, the other sensor
node can be disabled in the device tree.

The OV5642 module is connected to the parallel bus input on the i.MX
internal video mux to IPU1 CSI0. It's i2c bus connects to i2c bus 2.

The MIPI CSI-2 OV5640 module is connected to the i.MX internal MIPI CSI-2
receiver, and the four virtual channel outputs from the receiver are
routed as follows: vc0 to the IPU1 CSI0 mux, vc1 directly to IPU1 CSI1,
vc2 directly to IPU2 CSI0, and vc3 to the IPU2 CSI1 mux. The OV5640 is
also connected to i2c bus 2 on the SabreLite, therefore the OV5642 and
OV5640 must not share the same i2c slave address.

The following basic example configures unprocessed video capture
pipelines for both sensors. The OV5642 is routed to ipu1_csi0, and
the OV5640, transmitting on MIPI CSI-2 virtual channel 1 (which is
imx6-mipi-csi2 pad 2), is routed to ipu1_csi1. Both sensors are
configured to output 640x480, and the OV5642 outputs YUYV2X8, the
OV5640 UYVY2X8:

.. code-block:: none

   # Setup links for OV5642
   media-ctl -l "'ov5642 1-0042':0 -> 'ipu1_csi0_mux':1[1]"
   media-ctl -l "'ipu1_csi0_mux':2 -> 'ipu1_csi0':0[1]"
   media-ctl -l "'ipu1_csi0':2 -> 'ipu1_csi0 capture':0[1]"
   # Setup links for OV5640
   media-ctl -l "'ov5640 1-0040':0 -> 'imx6-mipi-csi2':0[1]"
   media-ctl -l "'imx6-mipi-csi2':2 -> 'ipu1_csi1':0[1]"
   media-ctl -l "'ipu1_csi1':2 -> 'ipu1_csi1 capture':0[1]"
   # Configure pads for OV5642 pipeline
   media-ctl -V "'ov5642 1-0042':0 [fmt:YUYV2X8/640x480 field:none]"
   media-ctl -V "'ipu1_csi0_mux':2 [fmt:YUYV2X8/640x480 field:none]"
   media-ctl -V "'ipu1_csi0':2 [fmt:AYUV32/640x480 field:none]"
   # Configure pads for OV5640 pipeline
   media-ctl -V "'ov5640 1-0040':0 [fmt:UYVY2X8/640x480 field:none]"
   media-ctl -V "'imx6-mipi-csi2':2 [fmt:UYVY2X8/640x480 field:none]"
   media-ctl -V "'ipu1_csi1':2 [fmt:AYUV32/640x480 field:none]"

Streaming can then begin independently on the capture device nodes
"ipu1_csi0 capture" and "ipu1_csi1 capture". The v4l2-ctl tool can
be used to select any supported YUV pixelformat on the capture device
nodes, including planar.

SabreAuto with ADV7180 decoder
------------------------------

On the SabreAuto, an on-board ADV7180 SD decoder is connected to the
parallel bus input on the internal video mux to IPU1 CSI0.

The following example configures a pipeline to capture from the ADV7180
video decoder, assuming NTSC 720x480 input signals, using simple
interweave (unconverted and without motion compensation). The adv7180
must output sequential or alternating fields (field type 'seq-bt' for
NTSC, or 'alternate'):

.. code-block:: none

   # Setup links
   media-ctl -l "'adv7180 3-0021':0 -> 'ipu1_csi0_mux':1[1]"
   media-ctl -l "'ipu1_csi0_mux':2 -> 'ipu1_csi0':0[1]"
   media-ctl -l "'ipu1_csi0':2 -> 'ipu1_csi0 capture':0[1]"
   # Configure pads
   media-ctl -V "'adv7180 3-0021':0 [fmt:UYVY2X8/720x480 field:seq-bt]"
   media-ctl -V "'ipu1_csi0_mux':2 [fmt:UYVY2X8/720x480]"
   media-ctl -V "'ipu1_csi0':2 [fmt:AYUV32/720x480]"
   # Configure "ipu1_csi0 capture" interface (assumed at /dev/video4)
   v4l2-ctl -d4 --set-fmt-video=field=interlaced_bt

Streaming can then begin on /dev/video4. The v4l2-ctl tool can also be
used to select any supported YUV pixelformat on /dev/video4.

This example configures a pipeline to capture from the ADV7180
video decoder, assuming PAL 720x576 input signals, with Motion
Compensated de-interlacing. The adv7180 must output sequential or
alternating fields (field type 'seq-tb' for PAL, or 'alternate').
$outputfmt can be any format supported by the ipu1_ic_prpvf entity
at its output pad:

.. code-block:: none

   # Setup links
   media-ctl -l "'adv7180 3-0021':0 -> 'ipu1_csi0_mux':1[1]"
   media-ctl -l "'ipu1_csi0_mux':2 -> 'ipu1_csi0':0[1]"
   media-ctl -l "'ipu1_csi0':1 -> 'ipu1_vdic':0[1]"
   media-ctl -l "'ipu1_vdic':2 -> 'ipu1_ic_prp':0[1]"
   media-ctl -l "'ipu1_ic_prp':2 -> 'ipu1_ic_prpvf':0[1]"
   media-ctl -l "'ipu1_ic_prpvf':1 -> 'ipu1_ic_prpvf capture':0[1]"
   # Configure pads
   media-ctl -V "'adv7180 3-0021':0 [fmt:UYVY2X8/720x576 field:seq-tb]"
   media-ctl -V "'ipu1_csi0_mux':2 [fmt:UYVY2X8/720x576]"
   media-ctl -V "'ipu1_csi0':1 [fmt:AYUV32/720x576]"
   media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]"
   media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]"
   media-ctl -V "'ipu1_ic_prpvf':1 [fmt:$outputfmt field:none]"

Streaming can then begin on the capture device node at
"ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any
supported YUV or RGB pixelformat on the capture device node.

This platform accepts Composite Video analog inputs to the ADV7180 on
Ain1 (connector J42).

SabreSD with MIPI CSI-2 OV5640
------------------------------

Similarly to SabreLite, the SabreSD supports a parallel interface
OV5642 module on IPU1 CSI0, and a MIPI CSI-2 OV5640 module. The OV5642
connects to i2c bus 1 and the OV5640 to i2c bus 2.

The device tree for SabreSD includes OF graphs for both the parallel
OV5642 and the MIPI CSI-2 OV5640, but as of this writing only the MIPI
CSI-2 OV5640 has been tested, so the OV5642 node is currently disabled.
The OV5640 module connects to MIPI connector J5 (sorry I don't have the
compatible module part number or URL).

The following example configures a direct conversion pipeline to capture
from the OV5640, transmitting on MIPI CSI-2 virtual channel 1. $sensorfmt
can be any format supported by the OV5640. $sensordim is the frame
dimension part of $sensorfmt (minus the mbus pixel code). $outputfmt can
be any format supported by the ipu1_ic_prpenc entity at its output pad:

.. code-block:: none

   # Setup links
   media-ctl -l "'ov5640 1-003c':0 -> 'imx6-mipi-csi2':0[1]"
   media-ctl -l "'imx6-mipi-csi2':2 -> 'ipu1_csi1':0[1]"
   media-ctl -l "'ipu1_csi1':1 -> 'ipu1_ic_prp':0[1]"
   media-ctl -l "'ipu1_ic_prp':1 -> 'ipu1_ic_prpenc':0[1]"
   media-ctl -l "'ipu1_ic_prpenc':1 -> 'ipu1_ic_prpenc capture':0[1]"
   # Configure pads
   media-ctl -V "'ov5640 1-003c':0 [fmt:$sensorfmt field:none]"
   media-ctl -V "'imx6-mipi-csi2':2 [fmt:$sensorfmt field:none]"
   media-ctl -V "'ipu1_csi1':1 [fmt:AYUV32/$sensordim field:none]"
   media-ctl -V "'ipu1_ic_prp':1 [fmt:AYUV32/$sensordim field:none]"
   media-ctl -V "'ipu1_ic_prpenc':1 [fmt:$outputfmt field:none]"

Streaming can then begin on "ipu1_ic_prpenc capture" node. The v4l2-ctl
tool can be used to select any supported YUV or RGB pixelformat on the
capture device node.


Known Issues
------------

1. When using 90 or 270 degree rotation control at capture resolutions
   near the IC resizer limit of 1024x1024, and combined with planar
   pixel formats (YUV420, YUV422p), frame capture will often fail with
   no end-of-frame interrupts from the IDMAC channel. To work around
   this, use lower resolution and/or packed formats (YUYV, RGB3, etc.)
   when 90 or 270 rotations are needed.


File list
---------

drivers/staging/media/imx/
include/media/imx.h
include/linux/imx-media.h

References
----------

.. [#f1] http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6DQRM.pdf
.. [#f2] http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6SDLRM.pdf


Authors
-------

- Steve Longerbeam <steve_longerbeam@mentor.com>
- Philipp Zabel <kernel@pengutronix.de>
- Russell King <linux@armlinux.org.uk>

Copyright (C) 2012-2017 Mentor Graphics Inc.