linux/drivers/mmc/card/Kconfig
Joe Millenbach 4f73bc4dd3 tty: Added a CONFIG_TTY option to allow removal of TTY
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48

Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-18 16:15:27 -08:00

71 lines
2.1 KiB
Plaintext

#
# MMC/SD card drivers
#
comment "MMC/SD/SDIO Card Drivers"
config MMC_BLOCK
tristate "MMC block device driver"
depends on BLOCK
default y
help
Say Y here to enable the MMC block device driver support.
This provides a block device driver, which you can use to
mount the filesystem. Almost everyone wishing MMC support
should say Y or M here.
config MMC_BLOCK_MINORS
int "Number of minors per block device"
depends on MMC_BLOCK
range 4 256
default 8
help
Number of minors per block device. One is needed for every
partition on the disk (plus one for the whole disk).
Number of total MMC minors available is 256, so your number
of supported block devices will be limited to 256 divided
by this number.
Default is 8 to be backwards compatible with previous
hardwired device numbering.
If unsure, say 8 here.
config MMC_BLOCK_BOUNCE
bool "Use bounce buffer for simple hosts"
depends on MMC_BLOCK
default y
help
SD/MMC is a high latency protocol where it is crucial to
send large requests in order to get high performance. Many
controllers, however, are restricted to continuous memory
(i.e. they can't do scatter-gather), something the kernel
rarely can provide.
Say Y here to help these restricted hosts by bouncing
requests back and forth from a large buffer. You will get
a big performance gain at the cost of up to 64 KiB of
physical memory.
If unsure, say Y here.
config SDIO_UART
tristate "SDIO UART/GPS class support"
depends on TTY
help
SDIO function driver for SDIO cards that implements the UART
class, as well as the GPS class which appears like a UART.
config MMC_TEST
tristate "MMC host test driver"
help
Development driver that performs a series of reads and writes
to a memory card in order to expose certain well known bugs
in host controllers. The tests are executed by writing to the
"test" file in debugfs under each card. Note that whatever is
on your card will be overwritten by these tests.
This driver is only of interest to those developing or
testing a host driver. Most people should say N here.