mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-28 13:34:38 +08:00
df73b7f842
CM-T3517, CM-T3530 and CM-T3730 features NAND storage chip connected to GPMC bus. Add GPMC DT entry into the root DT file omap3-cm-t3x.dtsi, common for all three modules. NAND timings are calculated to be safe for CM-T3x devices as it works now in non DT boot (in this case the timings are updated by U-Boot). Update GPMC ranges in boards DT files to include all connected devices. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
132 lines
3.1 KiB
Plaintext
132 lines
3.1 KiB
Plaintext
/*
|
|
* Common support for CompuLab CM-T3x30 CoMs
|
|
*/
|
|
|
|
#include "omap3-cm-t3x.dtsi"
|
|
|
|
/ {
|
|
cpus {
|
|
cpu@0 {
|
|
cpu0-supply = <&vcc>;
|
|
};
|
|
};
|
|
|
|
sound {
|
|
compatible = "ti,omap-twl4030";
|
|
ti,model = "cm-t35";
|
|
|
|
ti,mcbsp = <&mcbsp2>;
|
|
ti,codec = <&twl_audio>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
|
|
smsc1_pins: pinmux_smsc1_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */
|
|
OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */
|
|
>;
|
|
};
|
|
|
|
hsusb0_pins: pinmux_hsusb0_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
|
|
OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
|
|
OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
|
|
OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
|
|
OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */
|
|
OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
|
|
OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
|
|
OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */
|
|
OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */
|
|
OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */
|
|
OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */
|
|
OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
#include "omap-gpmc-smsc911x.dtsi"
|
|
|
|
&gpmc {
|
|
ranges = <5 0 0x2c000000 0x01000000>, /* CM-T3x30 SMSC9x Eth */
|
|
<0 0 0x00000000 0x01000000>; /* CM-T3x NAND */
|
|
|
|
smsc1: ethernet@gpmc {
|
|
compatible = "smsc,lan9221", "smsc,lan9115";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&smsc1_pins>;
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
|
reg = <5 0 0xff>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
twl: twl@48 {
|
|
reg = <0x48>;
|
|
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
|
|
interrupt-parent = <&intc>;
|
|
|
|
twl_audio: audio {
|
|
compatible = "ti,twl4030-audio";
|
|
codec {
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
#include "twl4030.dtsi"
|
|
#include "twl4030_omap3.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
&venc {
|
|
vdda-supply = <&vdac>;
|
|
};
|
|
|
|
&mmc1 {
|
|
vmmc-supply = <&vmmc1>;
|
|
};
|
|
|
|
&twl_gpio {
|
|
ti,use-leds;
|
|
/* pullups: BIT(0) */
|
|
ti,pullups = <0x000001>;
|
|
};
|
|
|
|
&twl_keypad {
|
|
linux,keymap = <
|
|
MATRIX_KEY(0x00, 0x01, KEY_A)
|
|
MATRIX_KEY(0x00, 0x02, KEY_B)
|
|
MATRIX_KEY(0x00, 0x03, KEY_LEFT)
|
|
|
|
MATRIX_KEY(0x01, 0x01, KEY_UP)
|
|
MATRIX_KEY(0x01, 0x02, KEY_ENTER)
|
|
MATRIX_KEY(0x01, 0x03, KEY_DOWN)
|
|
|
|
MATRIX_KEY(0x02, 0x01, KEY_RIGHT)
|
|
MATRIX_KEY(0x02, 0x02, KEY_C)
|
|
MATRIX_KEY(0x02, 0x03, KEY_D)
|
|
>;
|
|
};
|
|
|
|
&hsusb1_phy {
|
|
reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&hsusb2_phy {
|
|
reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&usb_otg_hs {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&hsusb0_pins>;
|
|
interface-type = <0>;
|
|
usb-phy = <&usb2_phy>;
|
|
phys = <&usb2_phy>;
|
|
phy-names = "usb2-phy";
|
|
mode = <3>;
|
|
power = <50>;
|
|
};
|