linux/drivers/phy/amlogic/phy-meson-gxl-usb3.c
Grygorii Strashko 79a5a18aa9 phy: core: rework phy_set_mode to accept phy mode and submode
Currently the attempt to add support for Ethernet interface mode PHY
(MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and
duplicate there values from phy_interface_t enum (or introduce more PHY
callbacks) [1]. Both approaches are ineffective and would lead to fast
bloating of enum phy_mode or struct phy_ops in the process of adding more
PHYs for different subsystems which will make them unmaintainable.

As discussed in [1] the solution could be to introduce dual level PHYs mode
configuration - PHY mode and PHY submode. The PHY mode will define generic
PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem
specific interface mode. The last is usually already defined in
corresponding subsystem headers (phy_interface_t for Ethernet, enum
usb_device_speed for USB).

This patch is cumulative change which refactors PHY framework code to
support dual level PHYs mode configuration - PHY mode and PHY submode. It
extends .set_mode() callback to support additional parameter "int submode"
and converts all corresponding PHY drivers to support new .set_mode()
callback declaration.
The new extended PHY API
 int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode)
is introduced to support dual level PHYs mode configuration and existing
phy_set_mode() API is converted to macros, so PHY framework consumers do
not need to be changed (~21 matches).

[1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.com
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-12-12 10:01:33 +05:30

284 lines
8.1 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* Meson GXL USB3 PHY and OTG mode detection driver
*
* Copyright (C) 2018 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
*/
#include <linux/bitfield.h>
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/phy/phy.h>
#include <linux/regmap.h>
#include <linux/reset.h>
#include <linux/platform_device.h>
#define USB_R0 0x00
#define USB_R0_P30_FSEL_MASK GENMASK(5, 0)
#define USB_R0_P30_PHY_RESET BIT(6)
#define USB_R0_P30_TEST_POWERDOWN_HSP BIT(7)
#define USB_R0_P30_TEST_POWERDOWN_SSP BIT(8)
#define USB_R0_P30_ACJT_LEVEL_MASK GENMASK(13, 9)
#define USB_R0_P30_TX_BOOST_LEVEL_MASK GENMASK(16, 14)
#define USB_R0_P30_LANE0_TX2RX_LOOPBACK BIT(17)
#define USB_R0_P30_LANE0_EXT_PCLK_REQ BIT(18)
#define USB_R0_P30_PCS_RX_LOS_MASK_VAL_MASK GENMASK(28, 19)
#define USB_R0_U2D_SS_SCALEDOWN_MODE_MASK GENMASK(30, 29)
#define USB_R0_U2D_ACT BIT(31)
#define USB_R1 0x04
#define USB_R1_U3H_BIGENDIAN_GS BIT(0)
#define USB_R1_U3H_PME_ENABLE BIT(1)
#define USB_R1_U3H_HUB_PORT_OVERCURRENT_MASK GENMASK(6, 2)
#define USB_R1_U3H_HUB_PORT_PERM_ATTACH_MASK GENMASK(11, 7)
#define USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK GENMASK(15, 12)
#define USB_R1_U3H_HOST_U3_PORT_DISABLE BIT(16)
#define USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT BIT(17)
#define USB_R1_U3H_HOST_MSI_ENABLE BIT(18)
#define USB_R1_U3H_FLADJ_30MHZ_REG_MASK GENMASK(24, 19)
#define USB_R1_P30_PCS_TX_SWING_FULL_MASK GENMASK(31, 25)
#define USB_R2 0x08
#define USB_R2_P30_CR_DATA_IN_MASK GENMASK(15, 0)
#define USB_R2_P30_CR_READ BIT(16)
#define USB_R2_P30_CR_WRITE BIT(17)
#define USB_R2_P30_CR_CAP_ADDR BIT(18)
#define USB_R2_P30_CR_CAP_DATA BIT(19)
#define USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK GENMASK(25, 20)
#define USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK GENMASK(31, 26)
#define USB_R3 0x0c
#define USB_R3_P30_SSC_ENABLE BIT(0)
#define USB_R3_P30_SSC_RANGE_MASK GENMASK(3, 1)
#define USB_R3_P30_SSC_REF_CLK_SEL_MASK GENMASK(12, 4)
#define USB_R3_P30_REF_SSP_EN BIT(13)
#define USB_R3_P30_LOS_BIAS_MASK GENMASK(18, 16)
#define USB_R3_P30_LOS_LEVEL_MASK GENMASK(23, 19)
#define USB_R3_P30_MPLL_MULTIPLIER_MASK GENMASK(30, 24)
#define USB_R4 0x10
#define USB_R4_P21_PORT_RESET_0 BIT(0)
#define USB_R4_P21_SLEEP_M0 BIT(1)
#define USB_R4_MEM_PD_MASK GENMASK(3, 2)
#define USB_R4_P21_ONLY BIT(4)
#define USB_R5 0x14
#define USB_R5_ID_DIG_SYNC BIT(0)
#define USB_R5_ID_DIG_REG BIT(1)
#define USB_R5_ID_DIG_CFG_MASK GENMASK(3, 2)
#define USB_R5_ID_DIG_EN_0 BIT(4)
#define USB_R5_ID_DIG_EN_1 BIT(5)
#define USB_R5_ID_DIG_CURR BIT(6)
#define USB_R5_ID_DIG_IRQ BIT(7)
#define USB_R5_ID_DIG_TH_MASK GENMASK(15, 8)
#define USB_R5_ID_DIG_CNT_MASK GENMASK(23, 16)
/* read-only register */
#define USB_R6 0x18
#define USB_R6_P30_CR_DATA_OUT_MASK GENMASK(15, 0)
#define USB_R6_P30_CR_ACK BIT(16)
struct phy_meson_gxl_usb3_priv {
struct regmap *regmap;
enum phy_mode mode;
struct clk *clk_phy;
struct clk *clk_peripheral;
struct reset_control *reset;
};
static const struct regmap_config phy_meson_gxl_usb3_regmap_conf = {
.reg_bits = 8,
.val_bits = 32,
.reg_stride = 4,
.max_register = USB_R6,
};
static int phy_meson_gxl_usb3_power_on(struct phy *phy)
{
struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_0,
USB_R5_ID_DIG_EN_0);
regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_1,
USB_R5_ID_DIG_EN_1);
regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_TH_MASK,
FIELD_PREP(USB_R5_ID_DIG_TH_MASK, 0xff));
return 0;
}
static int phy_meson_gxl_usb3_power_off(struct phy *phy)
{
struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_0, 0);
regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_1, 0);
return 0;
}
static int phy_meson_gxl_usb3_set_mode(struct phy *phy,
enum phy_mode mode, int submode)
{
struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
switch (mode) {
case PHY_MODE_USB_HOST:
regmap_update_bits(priv->regmap, USB_R0, USB_R0_U2D_ACT, 0);
regmap_update_bits(priv->regmap, USB_R4, USB_R4_P21_SLEEP_M0,
0);
break;
case PHY_MODE_USB_DEVICE:
regmap_update_bits(priv->regmap, USB_R0, USB_R0_U2D_ACT,
USB_R0_U2D_ACT);
regmap_update_bits(priv->regmap, USB_R4, USB_R4_P21_SLEEP_M0,
USB_R4_P21_SLEEP_M0);
break;
default:
dev_err(&phy->dev, "unsupported PHY mode %d\n", mode);
return -EINVAL;
}
priv->mode = mode;
return 0;
}
static int phy_meson_gxl_usb3_init(struct phy *phy)
{
struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
int ret;
ret = reset_control_reset(priv->reset);
if (ret)
goto err;
ret = clk_prepare_enable(priv->clk_phy);
if (ret)
goto err;
ret = clk_prepare_enable(priv->clk_peripheral);
if (ret)
goto err_disable_clk_phy;
ret = phy_meson_gxl_usb3_set_mode(phy, priv->mode, 0);
if (ret)
goto err_disable_clk_peripheral;
regmap_update_bits(priv->regmap, USB_R1,
USB_R1_U3H_FLADJ_30MHZ_REG_MASK,
FIELD_PREP(USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 0x20));
return 0;
err_disable_clk_peripheral:
clk_disable_unprepare(priv->clk_peripheral);
err_disable_clk_phy:
clk_disable_unprepare(priv->clk_phy);
err:
return ret;
}
static int phy_meson_gxl_usb3_exit(struct phy *phy)
{
struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
clk_disable_unprepare(priv->clk_peripheral);
clk_disable_unprepare(priv->clk_phy);
return 0;
}
static const struct phy_ops phy_meson_gxl_usb3_ops = {
.power_on = phy_meson_gxl_usb3_power_on,
.power_off = phy_meson_gxl_usb3_power_off,
.set_mode = phy_meson_gxl_usb3_set_mode,
.init = phy_meson_gxl_usb3_init,
.exit = phy_meson_gxl_usb3_exit,
.owner = THIS_MODULE,
};
static int phy_meson_gxl_usb3_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
struct phy_meson_gxl_usb3_priv *priv;
struct resource *res;
struct phy *phy;
struct phy_provider *phy_provider;
void __iomem *base;
int ret;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base = devm_ioremap_resource(dev, res);
if (IS_ERR(base))
return PTR_ERR(base);
priv->regmap = devm_regmap_init_mmio(dev, base,
&phy_meson_gxl_usb3_regmap_conf);
if (IS_ERR(priv->regmap))
return PTR_ERR(priv->regmap);
priv->clk_phy = devm_clk_get(dev, "phy");
if (IS_ERR(priv->clk_phy))
return PTR_ERR(priv->clk_phy);
priv->clk_peripheral = devm_clk_get(dev, "peripheral");
if (IS_ERR(priv->clk_peripheral))
return PTR_ERR(priv->clk_peripheral);
priv->reset = devm_reset_control_array_get_shared(dev);
if (IS_ERR(priv->reset))
return PTR_ERR(priv->reset);
/*
* default to host mode as hardware defaults and/or boot-loader
* behavior can result in this PHY starting up in device mode. this
* default and the initialization in phy_meson_gxl_usb3_init ensure
* that we reproducibly start in a known mode on all devices.
*/
priv->mode = PHY_MODE_USB_HOST;
phy = devm_phy_create(dev, np, &phy_meson_gxl_usb3_ops);
if (IS_ERR(phy)) {
ret = PTR_ERR(phy);
if (ret != -EPROBE_DEFER)
dev_err(dev, "failed to create PHY\n");
return ret;
}
phy_set_drvdata(phy, priv);
phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
return PTR_ERR_OR_ZERO(phy_provider);
}
static const struct of_device_id phy_meson_gxl_usb3_of_match[] = {
{ .compatible = "amlogic,meson-gxl-usb3-phy", },
{ },
};
MODULE_DEVICE_TABLE(of, phy_meson_gxl_usb3_of_match);
static struct platform_driver phy_meson_gxl_usb3_driver = {
.probe = phy_meson_gxl_usb3_probe,
.driver = {
.name = "phy-meson-gxl-usb3",
.of_match_table = phy_meson_gxl_usb3_of_match,
},
};
module_platform_driver(phy_meson_gxl_usb3_driver);
MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
MODULE_DESCRIPTION("Meson GXL USB3 PHY and OTG detection driver");
MODULE_LICENSE("GPL v2");