linux/arch/arm/boot/dts/imx28-cfa10049.dts
Maxime Ripard db7a8946dc ARM: dts: cfa10049: Add the DH2228FV DAC to the DTS
There is no driver for it yet, so it will use spidev.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-11-02 09:51:52 +08:00

117 lines
2.5 KiB
Plaintext

/*
* Copyright 2012 Free Electrons
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/*
* The CFA-10049 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
/include/ "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10049 Board";
compatible = "crystalfontz,cfa10049", "crystalfontz,cfa10036", "fsl,imx28";
apb@80000000 {
apbh@80000000 {
pinctrl@80018000 {
spi3_pins_cfa10049: spi3-cfa10049@0 {
reg = <0>;
fsl,pinmux-ids = <
0x0181 /* MX28_PAD_GPMI_RDN__SSP3_SCK */
0x01c1 /* MX28_PAD_GPMI_RESETN__SSP3_CMD */
0x0111 /* MX28_PAD_GPMI_CE1N__SSP3_D3 */
0x01a2 /* MX28_PAD_GPMI_ALE__SSP3_D4 */
0x01b2 /* MX28_PAD_GPMI_CLE__SSP3_D5 */
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
};
};
ssp3: ssp@80016000 {
compatible = "fsl,imx28-spi";
pinctrl-names = "default";
pinctrl-0 = <&spi3_pins_cfa10049>;
status = "okay";
gpio5: gpio5@0 {
compatible = "fairchild,74hc595";
gpio-controller;
#gpio-cells = <2>;
reg = <0>;
registers-number = <2>;
spi-max-frequency = <100000>;
};
gpio6: gpio6@1 {
compatible = "fairchild,74hc595";
gpio-controller;
#gpio-cells = <2>;
reg = <1>;
registers-number = <4>;
spi-max-frequency = <100000>;
};
dac0: dh2228@2 {
compatible = "rohm,dh2228fv";
reg = <2>;
spi-max-frequency = <100000>;
};
};
};
apbx@80040000 {
i2c1: i2c@8005a000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
usbphy1: usbphy@8007e000 {
status = "okay";
};
};
};
ahb@80080000 {
usb1: usb@80090000 {
vbus-supply = <&reg_usb1_vbus>;
pinctrl-0 = <&usbphy1_pins_a>;
pinctrl-names = "default";
status = "okay";
};
};
regulators {
compatible = "simple-bus";
reg_usb1_vbus: usb1_vbus {
compatible = "regulator-fixed";
regulator-name = "usb1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio0 7 1>;
};
};
ahb@80080000 {
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
phy-reset-gpios = <&gpio2 21 0>;
phy-reset-duration = <100>;
status = "okay";
};
};
};