mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-14 06:24:53 +08:00
01ce880380
Due to a mistake in documentation the DS0_PULL_UP_DOWN_EN macro was mistakenly defined as an active high bit, however setting the bit actually disables the internal pull resistor on the pin, so correct this macro and introduce a new DS0_PULL_UP_DOWN_DIS macro with the proper bit value set now that the documentation has been updated. Change based on AM437x Techninal Reference Manual SPRUHL7G Revised June 2017 Section 7.2.1. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
56 lines
1.7 KiB
C
56 lines
1.7 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* This header provides constants specific to AM43XX pinctrl bindings.
|
|
*/
|
|
|
|
#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H
|
|
#define _DT_BINDINGS_PINCTRL_AM43XX_H
|
|
|
|
#define MUX_MODE0 0
|
|
#define MUX_MODE1 1
|
|
#define MUX_MODE2 2
|
|
#define MUX_MODE3 3
|
|
#define MUX_MODE4 4
|
|
#define MUX_MODE5 5
|
|
#define MUX_MODE6 6
|
|
#define MUX_MODE7 7
|
|
#define MUX_MODE8 8
|
|
#define MUX_MODE9 9
|
|
|
|
#define PULL_DISABLE (1 << 16)
|
|
#define PULL_UP (1 << 17)
|
|
#define INPUT_EN (1 << 18)
|
|
#define SLEWCTRL_SLOW (1 << 19)
|
|
#define SLEWCTRL_FAST 0
|
|
#define DS0_FORCE_OFF_MODE (1 << 24)
|
|
#define DS0_INPUT (1 << 25)
|
|
#define DS0_FORCE_OUT_HIGH (1 << 26)
|
|
#define DS0_PULL_UP_DOWN_EN (0 << 27)
|
|
#define DS0_PULL_UP_DOWN_DIS (1 << 27)
|
|
#define DS0_PULL_UP_SEL (1 << 28)
|
|
#define WAKEUP_ENABLE (1 << 29)
|
|
|
|
#define DS0_PIN_OUTPUT (DS0_FORCE_OFF_MODE)
|
|
#define DS0_PIN_OUTPUT_HIGH (DS0_FORCE_OFF_MODE | DS0_FORCE_OUT_HIGH)
|
|
#define DS0_PIN_OUTPUT_PULLUP (DS0_FORCE_OFF_MODE | DS0_PULL_UP_DOWN_EN | DS0_PULL_UP_SEL)
|
|
#define DS0_PIN_OUTPUT_PULLDOWN (DS0_FORCE_OFF_MODE | DS0_PULL_UP_DOWN_EN)
|
|
#define DS0_PIN_INPUT (DS0_FORCE_OFF_MODE | DS0_INPUT)
|
|
#define DS0_PIN_INPUT_PULLUP (DS0_FORCE_OFF_MODE | DS0_INPUT | DS0_PULL_UP_DOWN_EN | DS0_PULL_UP_SEL)
|
|
#define DS0_PIN_INPUT_PULLDOWN (DS0_FORCE_OFF_MODE | DS0_INPUT | DS0_PULL_UP_DOWN_EN)
|
|
|
|
#define PIN_OUTPUT (PULL_DISABLE)
|
|
#define PIN_OUTPUT_PULLUP (PULL_UP)
|
|
#define PIN_OUTPUT_PULLDOWN 0
|
|
#define PIN_INPUT (INPUT_EN | PULL_DISABLE)
|
|
#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP)
|
|
#define PIN_INPUT_PULLDOWN (INPUT_EN)
|
|
|
|
/*
|
|
* Macro to allow using the absolute physical address instead of the
|
|
* padconf registers instead of the offset from padconf base.
|
|
*/
|
|
#define AM4372_IOPAD(pa, val) (((pa) & 0xffff) - 0x0800) (val)
|
|
|
|
#endif
|
|
|