mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-25 12:04:46 +08:00
a98ac8bd24
This patch is to add a documentation for ptp_qoriq dt-bindings. The description for ptp_qoriq dt-bindings was actually moved from Documentation/devicetree/bindings/net/fsl-tsec-phy.txt, since gianfar_ptp driver was moved to ptp_qoriq driver. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
90 lines
3.3 KiB
Plaintext
90 lines
3.3 KiB
Plaintext
* MDIO IO device
|
|
|
|
The MDIO is a bus to which the PHY devices are connected. For each
|
|
device that exists on this bus, a child node should be created. See
|
|
the definition of the PHY node in booting-without-of.txt for an example
|
|
of how to define a PHY.
|
|
|
|
Required properties:
|
|
- reg : Offset and length of the register set for the device, and optionally
|
|
the offset and length of the TBIPA register (TBI PHY address
|
|
register). If TBIPA register is not specified, the driver will
|
|
attempt to infer it from the register set specified (your mileage may
|
|
vary).
|
|
- compatible : Should define the compatible device type for the
|
|
mdio. Currently supported strings/devices are:
|
|
- "fsl,gianfar-tbi"
|
|
- "fsl,gianfar-mdio"
|
|
- "fsl,etsec2-tbi"
|
|
- "fsl,etsec2-mdio"
|
|
- "fsl,ucc-mdio"
|
|
- "fsl,fman-mdio"
|
|
When device_type is "mdio", the following strings are also considered:
|
|
- "gianfar"
|
|
- "ucc_geth_phy"
|
|
|
|
Example:
|
|
|
|
mdio@24520 {
|
|
reg = <24520 20>;
|
|
compatible = "fsl,gianfar-mdio";
|
|
|
|
ethernet-phy@0 {
|
|
......
|
|
};
|
|
};
|
|
|
|
* TBI Internal MDIO bus
|
|
|
|
As of this writing, every tsec is associated with an internal TBI PHY.
|
|
This PHY is accessed through the local MDIO bus. These buses are defined
|
|
similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
|
|
The TBI PHYs underneath them are similar to normal PHYs, but the reg property
|
|
is considered instructive, rather than descriptive. The reg property should
|
|
be chosen so it doesn't interfere with other PHYs on the bus.
|
|
|
|
* Gianfar-compatible ethernet nodes
|
|
|
|
Properties:
|
|
|
|
- device_type : Should be "network"
|
|
- model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
|
|
- compatible : Should be "gianfar"
|
|
- reg : Offset and length of the register set for the device
|
|
- interrupts : For FEC devices, the first interrupt is the device's
|
|
interrupt. For TSEC and eTSEC devices, the first interrupt is
|
|
transmit, the second is receive, and the third is error.
|
|
- phy-handle : See ethernet.txt file in the same directory.
|
|
- fixed-link : See fixed-link.txt in the same directory.
|
|
- phy-connection-type : See ethernet.txt file in the same directory.
|
|
This property is only really needed if the connection is of type
|
|
"rgmii-id", as all other connection types are detected by hardware.
|
|
- fsl,magic-packet : If present, indicates that the hardware supports
|
|
waking up via magic packet.
|
|
- fsl,wake-on-filer : If present, indicates that the hardware supports
|
|
waking up by Filer General Purpose Interrupt (FGPI) asserted on the
|
|
Rx int line. This is an advanced power management capability allowing
|
|
certain packet types (user) defined by filer rules to wake up the system.
|
|
- bd-stash : If present, indicates that the hardware supports stashing
|
|
buffer descriptors in the L2.
|
|
- rx-stash-len : Denotes the number of bytes of a received buffer to stash
|
|
in the L2.
|
|
- rx-stash-idx : Denotes the index of the first byte from the received
|
|
buffer to stash in the L2.
|
|
|
|
Example:
|
|
ethernet@24000 {
|
|
device_type = "network";
|
|
model = "TSEC";
|
|
compatible = "gianfar";
|
|
reg = <0x24000 0x1000>;
|
|
local-mac-address = [ 00 E0 0C 00 73 00 ];
|
|
interrupts = <29 2 30 2 34 2>;
|
|
interrupt-parent = <&mpic>;
|
|
phy-handle = <&phy0>
|
|
};
|
|
|
|
* Gianfar PTP clock nodes
|
|
|
|
Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt
|