mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-24 11:34:50 +08:00
d1acd81bd6
When driver is loaded after rmmod some drives are not showing up during discovery. SATA drives are directly attached to the controller connected phys. During device discovery, the IDENTIFY command (qc timeout (cmd 0xec)) is timing out during revalidation. This will trigger abort from host side and controller successfully aborts the command and returns success. Post this successful abort response ATA library decides to mark the disk as NODEV. To overcome this, inside pm8001_scan_start() after phy_start() call, add get start response and wait for few milliseconds to trigger next phy start. This millisecond delay will give sufficient time for the controller state machine to accept next phy start. Link: https://lore.kernel.org/r/20210505120103.24497-1-ajish.koshy@microchip.com Signed-off-by: Ajish Koshy <ajish.koshy@microchip.com> Signed-off-by: Viswas G <viswas.g@microchip.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1359 lines
39 KiB
C
1359 lines
39 KiB
C
/*
|
|
* PMC-Sierra PM8001/8081/8088/8089 SAS/SATA based host adapters driver
|
|
*
|
|
* Copyright (c) 2008-2009 USI Co., Ltd.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions, and the following disclaimer,
|
|
* without modification.
|
|
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
|
|
* substantially similar to the "NO WARRANTY" disclaimer below
|
|
* ("Disclaimer") and any redistribution must be conditioned upon
|
|
* including a substantially similar Disclaimer requirement for further
|
|
* binary redistribution.
|
|
* 3. Neither the names of the above-listed copyright holders nor the names
|
|
* of any contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* Alternatively, this software may be distributed under the terms of the
|
|
* GNU General Public License ("GPL") version 2 as published by the Free
|
|
* Software Foundation.
|
|
*
|
|
* NO WARRANTY
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
|
|
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
|
|
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGES.
|
|
*
|
|
*/
|
|
|
|
#include <linux/slab.h>
|
|
#include "pm8001_sas.h"
|
|
|
|
/**
|
|
* pm8001_find_tag - from sas task to find out tag that belongs to this task
|
|
* @task: the task sent to the LLDD
|
|
* @tag: the found tag associated with the task
|
|
*/
|
|
static int pm8001_find_tag(struct sas_task *task, u32 *tag)
|
|
{
|
|
if (task->lldd_task) {
|
|
struct pm8001_ccb_info *ccb;
|
|
ccb = task->lldd_task;
|
|
*tag = ccb->ccb_tag;
|
|
return 1;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pm8001_tag_free - free the no more needed tag
|
|
* @pm8001_ha: our hba struct
|
|
* @tag: the found tag associated with the task
|
|
*/
|
|
void pm8001_tag_free(struct pm8001_hba_info *pm8001_ha, u32 tag)
|
|
{
|
|
void *bitmap = pm8001_ha->tags;
|
|
clear_bit(tag, bitmap);
|
|
}
|
|
|
|
/**
|
|
* pm8001_tag_alloc - allocate a empty tag for task used.
|
|
* @pm8001_ha: our hba struct
|
|
* @tag_out: the found empty tag .
|
|
*/
|
|
inline int pm8001_tag_alloc(struct pm8001_hba_info *pm8001_ha, u32 *tag_out)
|
|
{
|
|
unsigned int tag;
|
|
void *bitmap = pm8001_ha->tags;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&pm8001_ha->bitmap_lock, flags);
|
|
tag = find_first_zero_bit(bitmap, pm8001_ha->tags_num);
|
|
if (tag >= pm8001_ha->tags_num) {
|
|
spin_unlock_irqrestore(&pm8001_ha->bitmap_lock, flags);
|
|
return -SAS_QUEUE_FULL;
|
|
}
|
|
set_bit(tag, bitmap);
|
|
spin_unlock_irqrestore(&pm8001_ha->bitmap_lock, flags);
|
|
*tag_out = tag;
|
|
return 0;
|
|
}
|
|
|
|
void pm8001_tag_init(struct pm8001_hba_info *pm8001_ha)
|
|
{
|
|
int i;
|
|
for (i = 0; i < pm8001_ha->tags_num; ++i)
|
|
pm8001_tag_free(pm8001_ha, i);
|
|
}
|
|
|
|
/**
|
|
* pm8001_mem_alloc - allocate memory for pm8001.
|
|
* @pdev: pci device.
|
|
* @virt_addr: the allocated virtual address
|
|
* @pphys_addr_hi: the physical address high byte address.
|
|
* @pphys_addr_lo: the physical address low byte address.
|
|
* @mem_size: memory size.
|
|
*/
|
|
int pm8001_mem_alloc(struct pci_dev *pdev, void **virt_addr,
|
|
dma_addr_t *pphys_addr, u32 *pphys_addr_hi,
|
|
u32 *pphys_addr_lo, u32 mem_size, u32 align)
|
|
{
|
|
caddr_t mem_virt_alloc;
|
|
dma_addr_t mem_dma_handle;
|
|
u64 phys_align;
|
|
u64 align_offset = 0;
|
|
if (align)
|
|
align_offset = (dma_addr_t)align - 1;
|
|
mem_virt_alloc = dma_alloc_coherent(&pdev->dev, mem_size + align,
|
|
&mem_dma_handle, GFP_KERNEL);
|
|
if (!mem_virt_alloc) {
|
|
pr_err("pm80xx: memory allocation error\n");
|
|
return -1;
|
|
}
|
|
*pphys_addr = mem_dma_handle;
|
|
phys_align = (*pphys_addr + align_offset) & ~align_offset;
|
|
*virt_addr = (void *)mem_virt_alloc + phys_align - *pphys_addr;
|
|
*pphys_addr_hi = upper_32_bits(phys_align);
|
|
*pphys_addr_lo = lower_32_bits(phys_align);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pm8001_find_ha_by_dev - from domain device which come from sas layer to
|
|
* find out our hba struct.
|
|
* @dev: the domain device which from sas layer.
|
|
*/
|
|
static
|
|
struct pm8001_hba_info *pm8001_find_ha_by_dev(struct domain_device *dev)
|
|
{
|
|
struct sas_ha_struct *sha = dev->port->ha;
|
|
struct pm8001_hba_info *pm8001_ha = sha->lldd_ha;
|
|
return pm8001_ha;
|
|
}
|
|
|
|
/**
|
|
* pm8001_phy_control - this function should be registered to
|
|
* sas_domain_function_template to provide libsas used, note: this is just
|
|
* control the HBA phy rather than other expander phy if you want control
|
|
* other phy, you should use SMP command.
|
|
* @sas_phy: which phy in HBA phys.
|
|
* @func: the operation.
|
|
* @funcdata: always NULL.
|
|
*/
|
|
int pm8001_phy_control(struct asd_sas_phy *sas_phy, enum phy_func func,
|
|
void *funcdata)
|
|
{
|
|
int rc = 0, phy_id = sas_phy->id;
|
|
struct pm8001_hba_info *pm8001_ha = NULL;
|
|
struct sas_phy_linkrates *rates;
|
|
struct pm8001_phy *phy;
|
|
DECLARE_COMPLETION_ONSTACK(completion);
|
|
unsigned long flags;
|
|
pm8001_ha = sas_phy->ha->lldd_ha;
|
|
phy = &pm8001_ha->phy[phy_id];
|
|
pm8001_ha->phy[phy_id].enable_completion = &completion;
|
|
switch (func) {
|
|
case PHY_FUNC_SET_LINK_RATE:
|
|
rates = funcdata;
|
|
if (rates->minimum_linkrate) {
|
|
pm8001_ha->phy[phy_id].minimum_linkrate =
|
|
rates->minimum_linkrate;
|
|
}
|
|
if (rates->maximum_linkrate) {
|
|
pm8001_ha->phy[phy_id].maximum_linkrate =
|
|
rates->maximum_linkrate;
|
|
}
|
|
if (pm8001_ha->phy[phy_id].phy_state == PHY_LINK_DISABLE) {
|
|
PM8001_CHIP_DISP->phy_start_req(pm8001_ha, phy_id);
|
|
wait_for_completion(&completion);
|
|
}
|
|
PM8001_CHIP_DISP->phy_ctl_req(pm8001_ha, phy_id,
|
|
PHY_LINK_RESET);
|
|
break;
|
|
case PHY_FUNC_HARD_RESET:
|
|
if (pm8001_ha->phy[phy_id].phy_state == PHY_LINK_DISABLE) {
|
|
PM8001_CHIP_DISP->phy_start_req(pm8001_ha, phy_id);
|
|
wait_for_completion(&completion);
|
|
}
|
|
PM8001_CHIP_DISP->phy_ctl_req(pm8001_ha, phy_id,
|
|
PHY_HARD_RESET);
|
|
break;
|
|
case PHY_FUNC_LINK_RESET:
|
|
if (pm8001_ha->phy[phy_id].phy_state == PHY_LINK_DISABLE) {
|
|
PM8001_CHIP_DISP->phy_start_req(pm8001_ha, phy_id);
|
|
wait_for_completion(&completion);
|
|
}
|
|
PM8001_CHIP_DISP->phy_ctl_req(pm8001_ha, phy_id,
|
|
PHY_LINK_RESET);
|
|
break;
|
|
case PHY_FUNC_RELEASE_SPINUP_HOLD:
|
|
PM8001_CHIP_DISP->phy_ctl_req(pm8001_ha, phy_id,
|
|
PHY_LINK_RESET);
|
|
break;
|
|
case PHY_FUNC_DISABLE:
|
|
if (pm8001_ha->chip_id != chip_8001) {
|
|
if (pm8001_ha->phy[phy_id].phy_state ==
|
|
PHY_STATE_LINK_UP_SPCV) {
|
|
sas_phy_disconnected(&phy->sas_phy);
|
|
sas_notify_phy_event(&phy->sas_phy,
|
|
PHYE_LOSS_OF_SIGNAL, GFP_KERNEL);
|
|
phy->phy_attached = 0;
|
|
}
|
|
} else {
|
|
if (pm8001_ha->phy[phy_id].phy_state ==
|
|
PHY_STATE_LINK_UP_SPC) {
|
|
sas_phy_disconnected(&phy->sas_phy);
|
|
sas_notify_phy_event(&phy->sas_phy,
|
|
PHYE_LOSS_OF_SIGNAL, GFP_KERNEL);
|
|
phy->phy_attached = 0;
|
|
}
|
|
}
|
|
PM8001_CHIP_DISP->phy_stop_req(pm8001_ha, phy_id);
|
|
break;
|
|
case PHY_FUNC_GET_EVENTS:
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
if (pm8001_ha->chip_id == chip_8001) {
|
|
if (-1 == pm8001_bar4_shift(pm8001_ha,
|
|
(phy_id < 4) ? 0x30000 : 0x40000)) {
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
{
|
|
struct sas_phy *phy = sas_phy->phy;
|
|
uint32_t *qp = (uint32_t *)(((char *)
|
|
pm8001_ha->io_mem[2].memvirtaddr)
|
|
+ 0x1034 + (0x4000 * (phy_id & 3)));
|
|
|
|
phy->invalid_dword_count = qp[0];
|
|
phy->running_disparity_error_count = qp[1];
|
|
phy->loss_of_dword_sync_count = qp[3];
|
|
phy->phy_reset_problem_count = qp[4];
|
|
}
|
|
if (pm8001_ha->chip_id == chip_8001)
|
|
pm8001_bar4_shift(pm8001_ha, 0);
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
return 0;
|
|
default:
|
|
pm8001_dbg(pm8001_ha, DEVIO, "func 0x%x\n", func);
|
|
rc = -EOPNOTSUPP;
|
|
}
|
|
msleep(300);
|
|
return rc;
|
|
}
|
|
|
|
/**
|
|
* pm8001_scan_start - we should enable all HBA phys by sending the phy_start
|
|
* command to HBA.
|
|
* @shost: the scsi host data.
|
|
*/
|
|
void pm8001_scan_start(struct Scsi_Host *shost)
|
|
{
|
|
int i;
|
|
struct pm8001_hba_info *pm8001_ha;
|
|
struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
|
|
DECLARE_COMPLETION_ONSTACK(completion);
|
|
pm8001_ha = sha->lldd_ha;
|
|
/* SAS_RE_INITIALIZATION not available in SPCv/ve */
|
|
if (pm8001_ha->chip_id == chip_8001)
|
|
PM8001_CHIP_DISP->sas_re_init_req(pm8001_ha);
|
|
for (i = 0; i < pm8001_ha->chip->n_phy; ++i) {
|
|
pm8001_ha->phy[i].enable_completion = &completion;
|
|
PM8001_CHIP_DISP->phy_start_req(pm8001_ha, i);
|
|
wait_for_completion(&completion);
|
|
msleep(300);
|
|
}
|
|
}
|
|
|
|
int pm8001_scan_finished(struct Scsi_Host *shost, unsigned long time)
|
|
{
|
|
struct sas_ha_struct *ha = SHOST_TO_SAS_HA(shost);
|
|
|
|
/* give the phy enabling interrupt event time to come in (1s
|
|
* is empirically about all it takes) */
|
|
if (time < HZ)
|
|
return 0;
|
|
/* Wait for discovery to finish */
|
|
sas_drain_work(ha);
|
|
return 1;
|
|
}
|
|
|
|
/**
|
|
* pm8001_task_prep_smp - the dispatcher function, prepare data for smp task
|
|
* @pm8001_ha: our hba card information
|
|
* @ccb: the ccb which attached to smp task
|
|
*/
|
|
static int pm8001_task_prep_smp(struct pm8001_hba_info *pm8001_ha,
|
|
struct pm8001_ccb_info *ccb)
|
|
{
|
|
return PM8001_CHIP_DISP->smp_req(pm8001_ha, ccb);
|
|
}
|
|
|
|
u32 pm8001_get_ncq_tag(struct sas_task *task, u32 *tag)
|
|
{
|
|
struct ata_queued_cmd *qc = task->uldd_task;
|
|
if (qc) {
|
|
if (qc->tf.command == ATA_CMD_FPDMA_WRITE ||
|
|
qc->tf.command == ATA_CMD_FPDMA_READ ||
|
|
qc->tf.command == ATA_CMD_FPDMA_RECV ||
|
|
qc->tf.command == ATA_CMD_FPDMA_SEND ||
|
|
qc->tf.command == ATA_CMD_NCQ_NON_DATA) {
|
|
*tag = qc->tag;
|
|
return 1;
|
|
}
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pm8001_task_prep_ata - the dispatcher function, prepare data for sata task
|
|
* @pm8001_ha: our hba card information
|
|
* @ccb: the ccb which attached to sata task
|
|
*/
|
|
static int pm8001_task_prep_ata(struct pm8001_hba_info *pm8001_ha,
|
|
struct pm8001_ccb_info *ccb)
|
|
{
|
|
return PM8001_CHIP_DISP->sata_req(pm8001_ha, ccb);
|
|
}
|
|
|
|
/**
|
|
* pm8001_task_prep_ssp_tm - the dispatcher function, prepare task management data
|
|
* @pm8001_ha: our hba card information
|
|
* @ccb: the ccb which attached to TM
|
|
* @tmf: the task management IU
|
|
*/
|
|
static int pm8001_task_prep_ssp_tm(struct pm8001_hba_info *pm8001_ha,
|
|
struct pm8001_ccb_info *ccb, struct pm8001_tmf_task *tmf)
|
|
{
|
|
return PM8001_CHIP_DISP->ssp_tm_req(pm8001_ha, ccb, tmf);
|
|
}
|
|
|
|
/**
|
|
* pm8001_task_prep_ssp - the dispatcher function,prepare ssp data for ssp task
|
|
* @pm8001_ha: our hba card information
|
|
* @ccb: the ccb which attached to ssp task
|
|
*/
|
|
static int pm8001_task_prep_ssp(struct pm8001_hba_info *pm8001_ha,
|
|
struct pm8001_ccb_info *ccb)
|
|
{
|
|
return PM8001_CHIP_DISP->ssp_io_req(pm8001_ha, ccb);
|
|
}
|
|
|
|
/* Find the local port id that's attached to this device */
|
|
static int sas_find_local_port_id(struct domain_device *dev)
|
|
{
|
|
struct domain_device *pdev = dev->parent;
|
|
|
|
/* Directly attached device */
|
|
if (!pdev)
|
|
return dev->port->id;
|
|
while (pdev) {
|
|
struct domain_device *pdev_p = pdev->parent;
|
|
if (!pdev_p)
|
|
return pdev->port->id;
|
|
pdev = pdev->parent;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
#define DEV_IS_GONE(pm8001_dev) \
|
|
((!pm8001_dev || (pm8001_dev->dev_type == SAS_PHY_UNUSED)))
|
|
/**
|
|
* pm8001_task_exec - queue the task(ssp, smp && ata) to the hardware.
|
|
* @task: the task to be execute.
|
|
* @gfp_flags: gfp_flags.
|
|
* @is_tmf: if it is task management task.
|
|
* @tmf: the task management IU
|
|
*/
|
|
static int pm8001_task_exec(struct sas_task *task,
|
|
gfp_t gfp_flags, int is_tmf, struct pm8001_tmf_task *tmf)
|
|
{
|
|
struct domain_device *dev = task->dev;
|
|
struct pm8001_hba_info *pm8001_ha;
|
|
struct pm8001_device *pm8001_dev;
|
|
struct pm8001_port *port = NULL;
|
|
struct sas_task *t = task;
|
|
struct pm8001_ccb_info *ccb;
|
|
u32 tag = 0xdeadbeef, rc = 0, n_elem = 0;
|
|
unsigned long flags = 0;
|
|
enum sas_protocol task_proto = t->task_proto;
|
|
|
|
if (!dev->port) {
|
|
struct task_status_struct *tsm = &t->task_status;
|
|
tsm->resp = SAS_TASK_UNDELIVERED;
|
|
tsm->stat = SAS_PHY_DOWN;
|
|
if (dev->dev_type != SAS_SATA_DEV)
|
|
t->task_done(t);
|
|
return 0;
|
|
}
|
|
pm8001_ha = pm8001_find_ha_by_dev(task->dev);
|
|
if (pm8001_ha->controller_fatal_error) {
|
|
struct task_status_struct *ts = &t->task_status;
|
|
|
|
ts->resp = SAS_TASK_UNDELIVERED;
|
|
t->task_done(t);
|
|
return 0;
|
|
}
|
|
pm8001_dbg(pm8001_ha, IO, "pm8001_task_exec device\n");
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
do {
|
|
dev = t->dev;
|
|
pm8001_dev = dev->lldd_dev;
|
|
port = &pm8001_ha->port[sas_find_local_port_id(dev)];
|
|
if (DEV_IS_GONE(pm8001_dev) || !port->port_attached) {
|
|
if (sas_protocol_ata(task_proto)) {
|
|
struct task_status_struct *ts = &t->task_status;
|
|
ts->resp = SAS_TASK_UNDELIVERED;
|
|
ts->stat = SAS_PHY_DOWN;
|
|
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
t->task_done(t);
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
continue;
|
|
} else {
|
|
struct task_status_struct *ts = &t->task_status;
|
|
ts->resp = SAS_TASK_UNDELIVERED;
|
|
ts->stat = SAS_PHY_DOWN;
|
|
t->task_done(t);
|
|
continue;
|
|
}
|
|
}
|
|
rc = pm8001_tag_alloc(pm8001_ha, &tag);
|
|
if (rc)
|
|
goto err_out;
|
|
ccb = &pm8001_ha->ccb_info[tag];
|
|
|
|
if (!sas_protocol_ata(task_proto)) {
|
|
if (t->num_scatter) {
|
|
n_elem = dma_map_sg(pm8001_ha->dev,
|
|
t->scatter,
|
|
t->num_scatter,
|
|
t->data_dir);
|
|
if (!n_elem) {
|
|
rc = -ENOMEM;
|
|
goto err_out_tag;
|
|
}
|
|
}
|
|
} else {
|
|
n_elem = t->num_scatter;
|
|
}
|
|
|
|
t->lldd_task = ccb;
|
|
ccb->n_elem = n_elem;
|
|
ccb->ccb_tag = tag;
|
|
ccb->task = t;
|
|
ccb->device = pm8001_dev;
|
|
switch (task_proto) {
|
|
case SAS_PROTOCOL_SMP:
|
|
atomic_inc(&pm8001_dev->running_req);
|
|
rc = pm8001_task_prep_smp(pm8001_ha, ccb);
|
|
break;
|
|
case SAS_PROTOCOL_SSP:
|
|
atomic_inc(&pm8001_dev->running_req);
|
|
if (is_tmf)
|
|
rc = pm8001_task_prep_ssp_tm(pm8001_ha,
|
|
ccb, tmf);
|
|
else
|
|
rc = pm8001_task_prep_ssp(pm8001_ha, ccb);
|
|
break;
|
|
case SAS_PROTOCOL_SATA:
|
|
case SAS_PROTOCOL_STP:
|
|
atomic_inc(&pm8001_dev->running_req);
|
|
rc = pm8001_task_prep_ata(pm8001_ha, ccb);
|
|
break;
|
|
default:
|
|
dev_printk(KERN_ERR, pm8001_ha->dev,
|
|
"unknown sas_task proto: 0x%x\n", task_proto);
|
|
rc = -EINVAL;
|
|
break;
|
|
}
|
|
|
|
if (rc) {
|
|
pm8001_dbg(pm8001_ha, IO, "rc is %x\n", rc);
|
|
atomic_dec(&pm8001_dev->running_req);
|
|
goto err_out_tag;
|
|
}
|
|
/* TODO: select normal or high priority */
|
|
spin_lock(&t->task_state_lock);
|
|
t->task_state_flags |= SAS_TASK_AT_INITIATOR;
|
|
spin_unlock(&t->task_state_lock);
|
|
} while (0);
|
|
rc = 0;
|
|
goto out_done;
|
|
|
|
err_out_tag:
|
|
pm8001_tag_free(pm8001_ha, tag);
|
|
err_out:
|
|
dev_printk(KERN_ERR, pm8001_ha->dev, "pm8001 exec failed[%d]!\n", rc);
|
|
if (!sas_protocol_ata(task_proto))
|
|
if (n_elem)
|
|
dma_unmap_sg(pm8001_ha->dev, t->scatter, t->num_scatter,
|
|
t->data_dir);
|
|
out_done:
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
return rc;
|
|
}
|
|
|
|
/**
|
|
* pm8001_queue_command - register for upper layer used, all IO commands sent
|
|
* to HBA are from this interface.
|
|
* @task: the task to be execute.
|
|
* @gfp_flags: gfp_flags
|
|
*/
|
|
int pm8001_queue_command(struct sas_task *task, gfp_t gfp_flags)
|
|
{
|
|
return pm8001_task_exec(task, gfp_flags, 0, NULL);
|
|
}
|
|
|
|
/**
|
|
* pm8001_ccb_task_free - free the sg for ssp and smp command, free the ccb.
|
|
* @pm8001_ha: our hba card information
|
|
* @ccb: the ccb which attached to ssp task
|
|
* @task: the task to be free.
|
|
* @ccb_idx: ccb index.
|
|
*/
|
|
void pm8001_ccb_task_free(struct pm8001_hba_info *pm8001_ha,
|
|
struct sas_task *task, struct pm8001_ccb_info *ccb, u32 ccb_idx)
|
|
{
|
|
if (!ccb->task)
|
|
return;
|
|
if (!sas_protocol_ata(task->task_proto))
|
|
if (ccb->n_elem)
|
|
dma_unmap_sg(pm8001_ha->dev, task->scatter,
|
|
task->num_scatter, task->data_dir);
|
|
|
|
switch (task->task_proto) {
|
|
case SAS_PROTOCOL_SMP:
|
|
dma_unmap_sg(pm8001_ha->dev, &task->smp_task.smp_resp, 1,
|
|
DMA_FROM_DEVICE);
|
|
dma_unmap_sg(pm8001_ha->dev, &task->smp_task.smp_req, 1,
|
|
DMA_TO_DEVICE);
|
|
break;
|
|
|
|
case SAS_PROTOCOL_SATA:
|
|
case SAS_PROTOCOL_STP:
|
|
case SAS_PROTOCOL_SSP:
|
|
default:
|
|
/* do nothing */
|
|
break;
|
|
}
|
|
task->lldd_task = NULL;
|
|
ccb->task = NULL;
|
|
ccb->ccb_tag = 0xFFFFFFFF;
|
|
ccb->open_retry = 0;
|
|
pm8001_tag_free(pm8001_ha, ccb_idx);
|
|
}
|
|
|
|
/**
|
|
* pm8001_alloc_dev - find a empty pm8001_device
|
|
* @pm8001_ha: our hba card information
|
|
*/
|
|
static struct pm8001_device *pm8001_alloc_dev(struct pm8001_hba_info *pm8001_ha)
|
|
{
|
|
u32 dev;
|
|
for (dev = 0; dev < PM8001_MAX_DEVICES; dev++) {
|
|
if (pm8001_ha->devices[dev].dev_type == SAS_PHY_UNUSED) {
|
|
pm8001_ha->devices[dev].id = dev;
|
|
return &pm8001_ha->devices[dev];
|
|
}
|
|
}
|
|
if (dev == PM8001_MAX_DEVICES) {
|
|
pm8001_dbg(pm8001_ha, FAIL,
|
|
"max support %d devices, ignore ..\n",
|
|
PM8001_MAX_DEVICES);
|
|
}
|
|
return NULL;
|
|
}
|
|
/**
|
|
* pm8001_find_dev - find a matching pm8001_device
|
|
* @pm8001_ha: our hba card information
|
|
* @device_id: device ID to match against
|
|
*/
|
|
struct pm8001_device *pm8001_find_dev(struct pm8001_hba_info *pm8001_ha,
|
|
u32 device_id)
|
|
{
|
|
u32 dev;
|
|
for (dev = 0; dev < PM8001_MAX_DEVICES; dev++) {
|
|
if (pm8001_ha->devices[dev].device_id == device_id)
|
|
return &pm8001_ha->devices[dev];
|
|
}
|
|
if (dev == PM8001_MAX_DEVICES) {
|
|
pm8001_dbg(pm8001_ha, FAIL, "NO MATCHING DEVICE FOUND !!!\n");
|
|
}
|
|
return NULL;
|
|
}
|
|
|
|
void pm8001_free_dev(struct pm8001_device *pm8001_dev)
|
|
{
|
|
u32 id = pm8001_dev->id;
|
|
memset(pm8001_dev, 0, sizeof(*pm8001_dev));
|
|
pm8001_dev->id = id;
|
|
pm8001_dev->dev_type = SAS_PHY_UNUSED;
|
|
pm8001_dev->device_id = PM8001_MAX_DEVICES;
|
|
pm8001_dev->sas_device = NULL;
|
|
}
|
|
|
|
/**
|
|
* pm8001_dev_found_notify - libsas notify a device is found.
|
|
* @dev: the device structure which sas layer used.
|
|
*
|
|
* when libsas find a sas domain device, it should tell the LLDD that
|
|
* device is found, and then LLDD register this device to HBA firmware
|
|
* by the command "OPC_INB_REG_DEV", after that the HBA will assign a
|
|
* device ID(according to device's sas address) and returned it to LLDD. From
|
|
* now on, we communicate with HBA FW with the device ID which HBA assigned
|
|
* rather than sas address. it is the necessary step for our HBA but it is
|
|
* the optional for other HBA driver.
|
|
*/
|
|
static int pm8001_dev_found_notify(struct domain_device *dev)
|
|
{
|
|
unsigned long flags = 0;
|
|
int res = 0;
|
|
struct pm8001_hba_info *pm8001_ha = NULL;
|
|
struct domain_device *parent_dev = dev->parent;
|
|
struct pm8001_device *pm8001_device;
|
|
DECLARE_COMPLETION_ONSTACK(completion);
|
|
u32 flag = 0;
|
|
pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
|
|
pm8001_device = pm8001_alloc_dev(pm8001_ha);
|
|
if (!pm8001_device) {
|
|
res = -1;
|
|
goto found_out;
|
|
}
|
|
pm8001_device->sas_device = dev;
|
|
dev->lldd_dev = pm8001_device;
|
|
pm8001_device->dev_type = dev->dev_type;
|
|
pm8001_device->dcompletion = &completion;
|
|
if (parent_dev && dev_is_expander(parent_dev->dev_type)) {
|
|
int phy_id;
|
|
struct ex_phy *phy;
|
|
for (phy_id = 0; phy_id < parent_dev->ex_dev.num_phys;
|
|
phy_id++) {
|
|
phy = &parent_dev->ex_dev.ex_phy[phy_id];
|
|
if (SAS_ADDR(phy->attached_sas_addr)
|
|
== SAS_ADDR(dev->sas_addr)) {
|
|
pm8001_device->attached_phy = phy_id;
|
|
break;
|
|
}
|
|
}
|
|
if (phy_id == parent_dev->ex_dev.num_phys) {
|
|
pm8001_dbg(pm8001_ha, FAIL,
|
|
"Error: no attached dev:%016llx at ex:%016llx.\n",
|
|
SAS_ADDR(dev->sas_addr),
|
|
SAS_ADDR(parent_dev->sas_addr));
|
|
res = -1;
|
|
}
|
|
} else {
|
|
if (dev->dev_type == SAS_SATA_DEV) {
|
|
pm8001_device->attached_phy =
|
|
dev->rphy->identify.phy_identifier;
|
|
flag = 1; /* directly sata */
|
|
}
|
|
} /*register this device to HBA*/
|
|
pm8001_dbg(pm8001_ha, DISC, "Found device\n");
|
|
PM8001_CHIP_DISP->reg_dev_req(pm8001_ha, pm8001_device, flag);
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
wait_for_completion(&completion);
|
|
if (dev->dev_type == SAS_END_DEVICE)
|
|
msleep(50);
|
|
pm8001_ha->flags = PM8001F_RUN_TIME;
|
|
return 0;
|
|
found_out:
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
return res;
|
|
}
|
|
|
|
int pm8001_dev_found(struct domain_device *dev)
|
|
{
|
|
return pm8001_dev_found_notify(dev);
|
|
}
|
|
|
|
void pm8001_task_done(struct sas_task *task)
|
|
{
|
|
if (!del_timer(&task->slow_task->timer))
|
|
return;
|
|
complete(&task->slow_task->completion);
|
|
}
|
|
|
|
static void pm8001_tmf_timedout(struct timer_list *t)
|
|
{
|
|
struct sas_task_slow *slow = from_timer(slow, t, timer);
|
|
struct sas_task *task = slow->task;
|
|
|
|
task->task_state_flags |= SAS_TASK_STATE_ABORTED;
|
|
complete(&task->slow_task->completion);
|
|
}
|
|
|
|
#define PM8001_TASK_TIMEOUT 20
|
|
/**
|
|
* pm8001_exec_internal_tmf_task - execute some task management commands.
|
|
* @dev: the wanted device.
|
|
* @tmf: which task management wanted to be take.
|
|
* @para_len: para_len.
|
|
* @parameter: ssp task parameter.
|
|
*
|
|
* when errors or exception happened, we may want to do something, for example
|
|
* abort the issued task which result in this execption, it is done by calling
|
|
* this function, note it is also with the task execute interface.
|
|
*/
|
|
static int pm8001_exec_internal_tmf_task(struct domain_device *dev,
|
|
void *parameter, u32 para_len, struct pm8001_tmf_task *tmf)
|
|
{
|
|
int res, retry;
|
|
struct sas_task *task = NULL;
|
|
struct pm8001_hba_info *pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
struct pm8001_device *pm8001_dev = dev->lldd_dev;
|
|
DECLARE_COMPLETION_ONSTACK(completion_setstate);
|
|
|
|
for (retry = 0; retry < 3; retry++) {
|
|
task = sas_alloc_slow_task(GFP_KERNEL);
|
|
if (!task)
|
|
return -ENOMEM;
|
|
|
|
task->dev = dev;
|
|
task->task_proto = dev->tproto;
|
|
memcpy(&task->ssp_task, parameter, para_len);
|
|
task->task_done = pm8001_task_done;
|
|
task->slow_task->timer.function = pm8001_tmf_timedout;
|
|
task->slow_task->timer.expires = jiffies + PM8001_TASK_TIMEOUT*HZ;
|
|
add_timer(&task->slow_task->timer);
|
|
|
|
res = pm8001_task_exec(task, GFP_KERNEL, 1, tmf);
|
|
|
|
if (res) {
|
|
del_timer(&task->slow_task->timer);
|
|
pm8001_dbg(pm8001_ha, FAIL, "Executing internal task failed\n");
|
|
goto ex_err;
|
|
}
|
|
wait_for_completion(&task->slow_task->completion);
|
|
if (pm8001_ha->chip_id != chip_8001) {
|
|
pm8001_dev->setds_completion = &completion_setstate;
|
|
PM8001_CHIP_DISP->set_dev_state_req(pm8001_ha,
|
|
pm8001_dev, DS_OPERATIONAL);
|
|
wait_for_completion(&completion_setstate);
|
|
}
|
|
res = -TMF_RESP_FUNC_FAILED;
|
|
/* Even TMF timed out, return direct. */
|
|
if ((task->task_state_flags & SAS_TASK_STATE_ABORTED)) {
|
|
if (!(task->task_state_flags & SAS_TASK_STATE_DONE)) {
|
|
pm8001_dbg(pm8001_ha, FAIL,
|
|
"TMF task[%x]timeout.\n",
|
|
tmf->tmf);
|
|
goto ex_err;
|
|
}
|
|
}
|
|
|
|
if (task->task_status.resp == SAS_TASK_COMPLETE &&
|
|
task->task_status.stat == SAM_STAT_GOOD) {
|
|
res = TMF_RESP_FUNC_COMPLETE;
|
|
break;
|
|
}
|
|
|
|
if (task->task_status.resp == SAS_TASK_COMPLETE &&
|
|
task->task_status.stat == SAS_DATA_UNDERRUN) {
|
|
/* no error, but return the number of bytes of
|
|
* underrun */
|
|
res = task->task_status.residual;
|
|
break;
|
|
}
|
|
|
|
if (task->task_status.resp == SAS_TASK_COMPLETE &&
|
|
task->task_status.stat == SAS_DATA_OVERRUN) {
|
|
pm8001_dbg(pm8001_ha, FAIL, "Blocked task error.\n");
|
|
res = -EMSGSIZE;
|
|
break;
|
|
} else {
|
|
pm8001_dbg(pm8001_ha, EH,
|
|
" Task to dev %016llx response:0x%x status 0x%x\n",
|
|
SAS_ADDR(dev->sas_addr),
|
|
task->task_status.resp,
|
|
task->task_status.stat);
|
|
sas_free_task(task);
|
|
task = NULL;
|
|
}
|
|
}
|
|
ex_err:
|
|
BUG_ON(retry == 3 && task != NULL);
|
|
sas_free_task(task);
|
|
return res;
|
|
}
|
|
|
|
static int
|
|
pm8001_exec_internal_task_abort(struct pm8001_hba_info *pm8001_ha,
|
|
struct pm8001_device *pm8001_dev, struct domain_device *dev, u32 flag,
|
|
u32 task_tag)
|
|
{
|
|
int res, retry;
|
|
u32 ccb_tag;
|
|
struct pm8001_ccb_info *ccb;
|
|
struct sas_task *task = NULL;
|
|
|
|
for (retry = 0; retry < 3; retry++) {
|
|
task = sas_alloc_slow_task(GFP_KERNEL);
|
|
if (!task)
|
|
return -ENOMEM;
|
|
|
|
task->dev = dev;
|
|
task->task_proto = dev->tproto;
|
|
task->task_done = pm8001_task_done;
|
|
task->slow_task->timer.function = pm8001_tmf_timedout;
|
|
task->slow_task->timer.expires = jiffies + PM8001_TASK_TIMEOUT * HZ;
|
|
add_timer(&task->slow_task->timer);
|
|
|
|
res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
|
|
if (res)
|
|
goto ex_err;
|
|
ccb = &pm8001_ha->ccb_info[ccb_tag];
|
|
ccb->device = pm8001_dev;
|
|
ccb->ccb_tag = ccb_tag;
|
|
ccb->task = task;
|
|
ccb->n_elem = 0;
|
|
|
|
res = PM8001_CHIP_DISP->task_abort(pm8001_ha,
|
|
pm8001_dev, flag, task_tag, ccb_tag);
|
|
|
|
if (res) {
|
|
del_timer(&task->slow_task->timer);
|
|
pm8001_dbg(pm8001_ha, FAIL, "Executing internal task failed\n");
|
|
goto ex_err;
|
|
}
|
|
wait_for_completion(&task->slow_task->completion);
|
|
res = TMF_RESP_FUNC_FAILED;
|
|
/* Even TMF timed out, return direct. */
|
|
if ((task->task_state_flags & SAS_TASK_STATE_ABORTED)) {
|
|
if (!(task->task_state_flags & SAS_TASK_STATE_DONE)) {
|
|
pm8001_dbg(pm8001_ha, FAIL,
|
|
"TMF task timeout.\n");
|
|
goto ex_err;
|
|
}
|
|
}
|
|
|
|
if (task->task_status.resp == SAS_TASK_COMPLETE &&
|
|
task->task_status.stat == SAM_STAT_GOOD) {
|
|
res = TMF_RESP_FUNC_COMPLETE;
|
|
break;
|
|
|
|
} else {
|
|
pm8001_dbg(pm8001_ha, EH,
|
|
" Task to dev %016llx response: 0x%x status 0x%x\n",
|
|
SAS_ADDR(dev->sas_addr),
|
|
task->task_status.resp,
|
|
task->task_status.stat);
|
|
sas_free_task(task);
|
|
task = NULL;
|
|
}
|
|
}
|
|
ex_err:
|
|
BUG_ON(retry == 3 && task != NULL);
|
|
sas_free_task(task);
|
|
return res;
|
|
}
|
|
|
|
/**
|
|
* pm8001_dev_gone_notify - see the comments for "pm8001_dev_found_notify"
|
|
* @dev: the device structure which sas layer used.
|
|
*/
|
|
static void pm8001_dev_gone_notify(struct domain_device *dev)
|
|
{
|
|
unsigned long flags = 0;
|
|
struct pm8001_hba_info *pm8001_ha;
|
|
struct pm8001_device *pm8001_dev = dev->lldd_dev;
|
|
|
|
pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
if (pm8001_dev) {
|
|
u32 device_id = pm8001_dev->device_id;
|
|
|
|
pm8001_dbg(pm8001_ha, DISC, "found dev[%d:%x] is gone.\n",
|
|
pm8001_dev->device_id, pm8001_dev->dev_type);
|
|
if (atomic_read(&pm8001_dev->running_req)) {
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
pm8001_exec_internal_task_abort(pm8001_ha, pm8001_dev,
|
|
dev, 1, 0);
|
|
while (atomic_read(&pm8001_dev->running_req))
|
|
msleep(20);
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
}
|
|
PM8001_CHIP_DISP->dereg_dev_req(pm8001_ha, device_id);
|
|
pm8001_free_dev(pm8001_dev);
|
|
} else {
|
|
pm8001_dbg(pm8001_ha, DISC, "Found dev has gone.\n");
|
|
}
|
|
dev->lldd_dev = NULL;
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
}
|
|
|
|
void pm8001_dev_gone(struct domain_device *dev)
|
|
{
|
|
pm8001_dev_gone_notify(dev);
|
|
}
|
|
|
|
static int pm8001_issue_ssp_tmf(struct domain_device *dev,
|
|
u8 *lun, struct pm8001_tmf_task *tmf)
|
|
{
|
|
struct sas_ssp_task ssp_task;
|
|
if (!(dev->tproto & SAS_PROTOCOL_SSP))
|
|
return TMF_RESP_FUNC_ESUPP;
|
|
|
|
memcpy((u8 *)&ssp_task.LUN, lun, 8);
|
|
return pm8001_exec_internal_tmf_task(dev, &ssp_task, sizeof(ssp_task),
|
|
tmf);
|
|
}
|
|
|
|
/* retry commands by ha, by task and/or by device */
|
|
void pm8001_open_reject_retry(
|
|
struct pm8001_hba_info *pm8001_ha,
|
|
struct sas_task *task_to_close,
|
|
struct pm8001_device *device_to_close)
|
|
{
|
|
int i;
|
|
unsigned long flags;
|
|
|
|
if (pm8001_ha == NULL)
|
|
return;
|
|
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
|
|
for (i = 0; i < PM8001_MAX_CCB; i++) {
|
|
struct sas_task *task;
|
|
struct task_status_struct *ts;
|
|
struct pm8001_device *pm8001_dev;
|
|
unsigned long flags1;
|
|
u32 tag;
|
|
struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[i];
|
|
|
|
pm8001_dev = ccb->device;
|
|
if (!pm8001_dev || (pm8001_dev->dev_type == SAS_PHY_UNUSED))
|
|
continue;
|
|
if (!device_to_close) {
|
|
uintptr_t d = (uintptr_t)pm8001_dev
|
|
- (uintptr_t)&pm8001_ha->devices;
|
|
if (((d % sizeof(*pm8001_dev)) != 0)
|
|
|| ((d / sizeof(*pm8001_dev)) >= PM8001_MAX_DEVICES))
|
|
continue;
|
|
} else if (pm8001_dev != device_to_close)
|
|
continue;
|
|
tag = ccb->ccb_tag;
|
|
if (!tag || (tag == 0xFFFFFFFF))
|
|
continue;
|
|
task = ccb->task;
|
|
if (!task || !task->task_done)
|
|
continue;
|
|
if (task_to_close && (task != task_to_close))
|
|
continue;
|
|
ts = &task->task_status;
|
|
ts->resp = SAS_TASK_COMPLETE;
|
|
/* Force the midlayer to retry */
|
|
ts->stat = SAS_OPEN_REJECT;
|
|
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
|
|
if (pm8001_dev)
|
|
atomic_dec(&pm8001_dev->running_req);
|
|
spin_lock_irqsave(&task->task_state_lock, flags1);
|
|
task->task_state_flags &= ~SAS_TASK_STATE_PENDING;
|
|
task->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
|
|
task->task_state_flags |= SAS_TASK_STATE_DONE;
|
|
if (unlikely((task->task_state_flags
|
|
& SAS_TASK_STATE_ABORTED))) {
|
|
spin_unlock_irqrestore(&task->task_state_lock,
|
|
flags1);
|
|
pm8001_ccb_task_free(pm8001_ha, task, ccb, tag);
|
|
} else {
|
|
spin_unlock_irqrestore(&task->task_state_lock,
|
|
flags1);
|
|
pm8001_ccb_task_free(pm8001_ha, task, ccb, tag);
|
|
mb();/* in order to force CPU ordering */
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
task->task_done(task);
|
|
spin_lock_irqsave(&pm8001_ha->lock, flags);
|
|
}
|
|
}
|
|
|
|
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
|
|
}
|
|
|
|
/**
|
|
* pm8001_I_T_nexus_reset()
|
|
* Standard mandates link reset for ATA (type 0) and hard reset for
|
|
* SSP (type 1) , only for RECOVERY
|
|
* @dev: the device structure for the device to reset.
|
|
*/
|
|
int pm8001_I_T_nexus_reset(struct domain_device *dev)
|
|
{
|
|
int rc = TMF_RESP_FUNC_FAILED;
|
|
struct pm8001_device *pm8001_dev;
|
|
struct pm8001_hba_info *pm8001_ha;
|
|
struct sas_phy *phy;
|
|
|
|
if (!dev || !dev->lldd_dev)
|
|
return -ENODEV;
|
|
|
|
pm8001_dev = dev->lldd_dev;
|
|
pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
phy = sas_get_local_phy(dev);
|
|
|
|
if (dev_is_sata(dev)) {
|
|
if (scsi_is_sas_phy_local(phy)) {
|
|
rc = 0;
|
|
goto out;
|
|
}
|
|
rc = sas_phy_reset(phy, 1);
|
|
if (rc) {
|
|
pm8001_dbg(pm8001_ha, EH,
|
|
"phy reset failed for device %x\n"
|
|
"with rc %d\n", pm8001_dev->device_id, rc);
|
|
rc = TMF_RESP_FUNC_FAILED;
|
|
goto out;
|
|
}
|
|
msleep(2000);
|
|
rc = pm8001_exec_internal_task_abort(pm8001_ha, pm8001_dev,
|
|
dev, 1, 0);
|
|
if (rc) {
|
|
pm8001_dbg(pm8001_ha, EH, "task abort failed %x\n"
|
|
"with rc %d\n", pm8001_dev->device_id, rc);
|
|
rc = TMF_RESP_FUNC_FAILED;
|
|
}
|
|
} else {
|
|
rc = sas_phy_reset(phy, 1);
|
|
msleep(2000);
|
|
}
|
|
pm8001_dbg(pm8001_ha, EH, " for device[%x]:rc=%d\n",
|
|
pm8001_dev->device_id, rc);
|
|
out:
|
|
sas_put_local_phy(phy);
|
|
return rc;
|
|
}
|
|
|
|
/*
|
|
* This function handle the IT_NEXUS_XXX event or completion
|
|
* status code for SSP/SATA/SMP I/O request.
|
|
*/
|
|
int pm8001_I_T_nexus_event_handler(struct domain_device *dev)
|
|
{
|
|
int rc = TMF_RESP_FUNC_FAILED;
|
|
struct pm8001_device *pm8001_dev;
|
|
struct pm8001_hba_info *pm8001_ha;
|
|
struct sas_phy *phy;
|
|
|
|
if (!dev || !dev->lldd_dev)
|
|
return -1;
|
|
|
|
pm8001_dev = dev->lldd_dev;
|
|
pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
|
|
pm8001_dbg(pm8001_ha, EH, "I_T_Nexus handler invoked !!\n");
|
|
|
|
phy = sas_get_local_phy(dev);
|
|
|
|
if (dev_is_sata(dev)) {
|
|
DECLARE_COMPLETION_ONSTACK(completion_setstate);
|
|
if (scsi_is_sas_phy_local(phy)) {
|
|
rc = 0;
|
|
goto out;
|
|
}
|
|
/* send internal ssp/sata/smp abort command to FW */
|
|
rc = pm8001_exec_internal_task_abort(pm8001_ha, pm8001_dev,
|
|
dev, 1, 0);
|
|
msleep(100);
|
|
|
|
/* deregister the target device */
|
|
pm8001_dev_gone_notify(dev);
|
|
msleep(200);
|
|
|
|
/*send phy reset to hard reset target */
|
|
rc = sas_phy_reset(phy, 1);
|
|
msleep(2000);
|
|
pm8001_dev->setds_completion = &completion_setstate;
|
|
|
|
wait_for_completion(&completion_setstate);
|
|
} else {
|
|
/* send internal ssp/sata/smp abort command to FW */
|
|
rc = pm8001_exec_internal_task_abort(pm8001_ha, pm8001_dev,
|
|
dev, 1, 0);
|
|
msleep(100);
|
|
|
|
/* deregister the target device */
|
|
pm8001_dev_gone_notify(dev);
|
|
msleep(200);
|
|
|
|
/*send phy reset to hard reset target */
|
|
rc = sas_phy_reset(phy, 1);
|
|
msleep(2000);
|
|
}
|
|
pm8001_dbg(pm8001_ha, EH, " for device[%x]:rc=%d\n",
|
|
pm8001_dev->device_id, rc);
|
|
out:
|
|
sas_put_local_phy(phy);
|
|
|
|
return rc;
|
|
}
|
|
/* mandatory SAM-3, the task reset the specified LUN*/
|
|
int pm8001_lu_reset(struct domain_device *dev, u8 *lun)
|
|
{
|
|
int rc = TMF_RESP_FUNC_FAILED;
|
|
struct pm8001_tmf_task tmf_task;
|
|
struct pm8001_device *pm8001_dev = dev->lldd_dev;
|
|
struct pm8001_hba_info *pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
DECLARE_COMPLETION_ONSTACK(completion_setstate);
|
|
if (dev_is_sata(dev)) {
|
|
struct sas_phy *phy = sas_get_local_phy(dev);
|
|
rc = pm8001_exec_internal_task_abort(pm8001_ha, pm8001_dev,
|
|
dev, 1, 0);
|
|
rc = sas_phy_reset(phy, 1);
|
|
sas_put_local_phy(phy);
|
|
pm8001_dev->setds_completion = &completion_setstate;
|
|
rc = PM8001_CHIP_DISP->set_dev_state_req(pm8001_ha,
|
|
pm8001_dev, DS_OPERATIONAL);
|
|
wait_for_completion(&completion_setstate);
|
|
} else {
|
|
tmf_task.tmf = TMF_LU_RESET;
|
|
rc = pm8001_issue_ssp_tmf(dev, lun, &tmf_task);
|
|
}
|
|
/* If failed, fall-through I_T_Nexus reset */
|
|
pm8001_dbg(pm8001_ha, EH, "for device[%x]:rc=%d\n",
|
|
pm8001_dev->device_id, rc);
|
|
return rc;
|
|
}
|
|
|
|
/* optional SAM-3 */
|
|
int pm8001_query_task(struct sas_task *task)
|
|
{
|
|
u32 tag = 0xdeadbeef;
|
|
struct scsi_lun lun;
|
|
struct pm8001_tmf_task tmf_task;
|
|
int rc = TMF_RESP_FUNC_FAILED;
|
|
if (unlikely(!task || !task->lldd_task || !task->dev))
|
|
return rc;
|
|
|
|
if (task->task_proto & SAS_PROTOCOL_SSP) {
|
|
struct scsi_cmnd *cmnd = task->uldd_task;
|
|
struct domain_device *dev = task->dev;
|
|
struct pm8001_hba_info *pm8001_ha =
|
|
pm8001_find_ha_by_dev(dev);
|
|
|
|
int_to_scsilun(cmnd->device->lun, &lun);
|
|
rc = pm8001_find_tag(task, &tag);
|
|
if (rc == 0) {
|
|
rc = TMF_RESP_FUNC_FAILED;
|
|
return rc;
|
|
}
|
|
pm8001_dbg(pm8001_ha, EH, "Query:[%16ph]\n", cmnd->cmnd);
|
|
tmf_task.tmf = TMF_QUERY_TASK;
|
|
tmf_task.tag_of_task_to_be_managed = tag;
|
|
|
|
rc = pm8001_issue_ssp_tmf(dev, lun.scsi_lun, &tmf_task);
|
|
switch (rc) {
|
|
/* The task is still in Lun, release it then */
|
|
case TMF_RESP_FUNC_SUCC:
|
|
pm8001_dbg(pm8001_ha, EH,
|
|
"The task is still in Lun\n");
|
|
break;
|
|
/* The task is not in Lun or failed, reset the phy */
|
|
case TMF_RESP_FUNC_FAILED:
|
|
case TMF_RESP_FUNC_COMPLETE:
|
|
pm8001_dbg(pm8001_ha, EH,
|
|
"The task is not in Lun or failed, reset the phy\n");
|
|
break;
|
|
}
|
|
}
|
|
pr_err("pm80xx: rc= %d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
/* mandatory SAM-3, still need free task/ccb info, abort the specified task */
|
|
int pm8001_abort_task(struct sas_task *task)
|
|
{
|
|
unsigned long flags;
|
|
u32 tag;
|
|
struct domain_device *dev ;
|
|
struct pm8001_hba_info *pm8001_ha;
|
|
struct scsi_lun lun;
|
|
struct pm8001_device *pm8001_dev;
|
|
struct pm8001_tmf_task tmf_task;
|
|
int rc = TMF_RESP_FUNC_FAILED, ret;
|
|
u32 phy_id;
|
|
struct sas_task_slow slow_task;
|
|
|
|
if (unlikely(!task || !task->lldd_task || !task->dev))
|
|
return TMF_RESP_FUNC_FAILED;
|
|
|
|
dev = task->dev;
|
|
pm8001_dev = dev->lldd_dev;
|
|
pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
phy_id = pm8001_dev->attached_phy;
|
|
|
|
if (PM8001_CHIP_DISP->fatal_errors(pm8001_ha)) {
|
|
// If the controller is seeing fatal errors
|
|
// abort task will not get a response from the controller
|
|
return TMF_RESP_FUNC_FAILED;
|
|
}
|
|
|
|
ret = pm8001_find_tag(task, &tag);
|
|
if (ret == 0) {
|
|
pm8001_info(pm8001_ha, "no tag for task:%p\n", task);
|
|
return TMF_RESP_FUNC_FAILED;
|
|
}
|
|
spin_lock_irqsave(&task->task_state_lock, flags);
|
|
if (task->task_state_flags & SAS_TASK_STATE_DONE) {
|
|
spin_unlock_irqrestore(&task->task_state_lock, flags);
|
|
return TMF_RESP_FUNC_COMPLETE;
|
|
}
|
|
task->task_state_flags |= SAS_TASK_STATE_ABORTED;
|
|
if (task->slow_task == NULL) {
|
|
init_completion(&slow_task.completion);
|
|
task->slow_task = &slow_task;
|
|
}
|
|
spin_unlock_irqrestore(&task->task_state_lock, flags);
|
|
if (task->task_proto & SAS_PROTOCOL_SSP) {
|
|
struct scsi_cmnd *cmnd = task->uldd_task;
|
|
int_to_scsilun(cmnd->device->lun, &lun);
|
|
tmf_task.tmf = TMF_ABORT_TASK;
|
|
tmf_task.tag_of_task_to_be_managed = tag;
|
|
rc = pm8001_issue_ssp_tmf(dev, lun.scsi_lun, &tmf_task);
|
|
pm8001_exec_internal_task_abort(pm8001_ha, pm8001_dev,
|
|
pm8001_dev->sas_device, 0, tag);
|
|
} else if (task->task_proto & SAS_PROTOCOL_SATA ||
|
|
task->task_proto & SAS_PROTOCOL_STP) {
|
|
if (pm8001_ha->chip_id == chip_8006) {
|
|
DECLARE_COMPLETION_ONSTACK(completion_reset);
|
|
DECLARE_COMPLETION_ONSTACK(completion);
|
|
struct pm8001_phy *phy = pm8001_ha->phy + phy_id;
|
|
|
|
/* 1. Set Device state as Recovery */
|
|
pm8001_dev->setds_completion = &completion;
|
|
PM8001_CHIP_DISP->set_dev_state_req(pm8001_ha,
|
|
pm8001_dev, DS_IN_RECOVERY);
|
|
wait_for_completion(&completion);
|
|
|
|
/* 2. Send Phy Control Hard Reset */
|
|
reinit_completion(&completion);
|
|
phy->port_reset_status = PORT_RESET_TMO;
|
|
phy->reset_success = false;
|
|
phy->enable_completion = &completion;
|
|
phy->reset_completion = &completion_reset;
|
|
ret = PM8001_CHIP_DISP->phy_ctl_req(pm8001_ha, phy_id,
|
|
PHY_HARD_RESET);
|
|
if (ret) {
|
|
phy->enable_completion = NULL;
|
|
phy->reset_completion = NULL;
|
|
goto out;
|
|
}
|
|
|
|
/* In the case of the reset timeout/fail we still
|
|
* abort the command at the firmware. The assumption
|
|
* here is that the drive is off doing something so
|
|
* that it's not processing requests, and we want to
|
|
* avoid getting a completion for this and either
|
|
* leaking the task in libsas or losing the race and
|
|
* getting a double free.
|
|
*/
|
|
pm8001_dbg(pm8001_ha, MSG,
|
|
"Waiting for local phy ctl\n");
|
|
ret = wait_for_completion_timeout(&completion,
|
|
PM8001_TASK_TIMEOUT * HZ);
|
|
if (!ret || !phy->reset_success) {
|
|
phy->enable_completion = NULL;
|
|
phy->reset_completion = NULL;
|
|
} else {
|
|
/* 3. Wait for Port Reset complete or
|
|
* Port reset TMO
|
|
*/
|
|
pm8001_dbg(pm8001_ha, MSG,
|
|
"Waiting for Port reset\n");
|
|
ret = wait_for_completion_timeout(
|
|
&completion_reset,
|
|
PM8001_TASK_TIMEOUT * HZ);
|
|
if (!ret)
|
|
phy->reset_completion = NULL;
|
|
WARN_ON(phy->port_reset_status ==
|
|
PORT_RESET_TMO);
|
|
if (phy->port_reset_status == PORT_RESET_TMO) {
|
|
pm8001_dev_gone_notify(dev);
|
|
goto out;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* 4. SATA Abort ALL
|
|
* we wait for the task to be aborted so that the task
|
|
* is removed from the ccb. on success the caller is
|
|
* going to free the task.
|
|
*/
|
|
ret = pm8001_exec_internal_task_abort(pm8001_ha,
|
|
pm8001_dev, pm8001_dev->sas_device, 1, tag);
|
|
if (ret)
|
|
goto out;
|
|
ret = wait_for_completion_timeout(
|
|
&task->slow_task->completion,
|
|
PM8001_TASK_TIMEOUT * HZ);
|
|
if (!ret)
|
|
goto out;
|
|
|
|
/* 5. Set Device State as Operational */
|
|
reinit_completion(&completion);
|
|
pm8001_dev->setds_completion = &completion;
|
|
PM8001_CHIP_DISP->set_dev_state_req(pm8001_ha,
|
|
pm8001_dev, DS_OPERATIONAL);
|
|
wait_for_completion(&completion);
|
|
} else {
|
|
rc = pm8001_exec_internal_task_abort(pm8001_ha,
|
|
pm8001_dev, pm8001_dev->sas_device, 0, tag);
|
|
}
|
|
rc = TMF_RESP_FUNC_COMPLETE;
|
|
} else if (task->task_proto & SAS_PROTOCOL_SMP) {
|
|
/* SMP */
|
|
rc = pm8001_exec_internal_task_abort(pm8001_ha, pm8001_dev,
|
|
pm8001_dev->sas_device, 0, tag);
|
|
|
|
}
|
|
out:
|
|
spin_lock_irqsave(&task->task_state_lock, flags);
|
|
if (task->slow_task == &slow_task)
|
|
task->slow_task = NULL;
|
|
spin_unlock_irqrestore(&task->task_state_lock, flags);
|
|
if (rc != TMF_RESP_FUNC_COMPLETE)
|
|
pm8001_info(pm8001_ha, "rc= %d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
int pm8001_abort_task_set(struct domain_device *dev, u8 *lun)
|
|
{
|
|
struct pm8001_tmf_task tmf_task;
|
|
|
|
tmf_task.tmf = TMF_ABORT_TASK_SET;
|
|
return pm8001_issue_ssp_tmf(dev, lun, &tmf_task);
|
|
}
|
|
|
|
int pm8001_clear_aca(struct domain_device *dev, u8 *lun)
|
|
{
|
|
struct pm8001_tmf_task tmf_task;
|
|
|
|
tmf_task.tmf = TMF_CLEAR_ACA;
|
|
return pm8001_issue_ssp_tmf(dev, lun, &tmf_task);
|
|
}
|
|
|
|
int pm8001_clear_task_set(struct domain_device *dev, u8 *lun)
|
|
{
|
|
struct pm8001_tmf_task tmf_task;
|
|
struct pm8001_device *pm8001_dev = dev->lldd_dev;
|
|
struct pm8001_hba_info *pm8001_ha = pm8001_find_ha_by_dev(dev);
|
|
|
|
pm8001_dbg(pm8001_ha, EH, "I_T_L_Q clear task set[%x]\n",
|
|
pm8001_dev->device_id);
|
|
tmf_task.tmf = TMF_CLEAR_TASK_SET;
|
|
return pm8001_issue_ssp_tmf(dev, lun, &tmf_task);
|
|
}
|