mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2025-01-21 13:24:15 +08:00
a7f7f6248d
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
66 lines
1.9 KiB
Plaintext
66 lines
1.9 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# Qualcomm network device configuration
|
|
#
|
|
|
|
config NET_VENDOR_QUALCOMM
|
|
bool "Qualcomm devices"
|
|
default y
|
|
help
|
|
If you have a network (Ethernet) card belonging to this class, say Y.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about Qualcomm cards. If you say Y, you will be asked
|
|
for your specific card in the following questions.
|
|
|
|
if NET_VENDOR_QUALCOMM
|
|
|
|
config QCA7000
|
|
tristate
|
|
help
|
|
This enables support for the Qualcomm Atheros QCA7000.
|
|
|
|
config QCA7000_SPI
|
|
tristate "Qualcomm Atheros QCA7000 SPI support"
|
|
select QCA7000
|
|
depends on SPI_MASTER && OF
|
|
help
|
|
This SPI protocol driver supports the Qualcomm Atheros QCA7000.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called qcaspi.
|
|
|
|
config QCA7000_UART
|
|
tristate "Qualcomm Atheros QCA7000 UART support"
|
|
select QCA7000
|
|
depends on SERIAL_DEV_BUS && OF
|
|
help
|
|
This UART protocol driver supports the Qualcomm Atheros QCA7000.
|
|
|
|
Currently the driver assumes these device UART settings:
|
|
Data bits: 8
|
|
Parity: None
|
|
Stop bits: 1
|
|
Flow control: None
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called qcauart.
|
|
|
|
config QCOM_EMAC
|
|
tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
|
|
depends on HAS_DMA && HAS_IOMEM
|
|
select CRC32
|
|
select PHYLIB
|
|
help
|
|
This driver supports the Qualcomm Technologies, Inc. Gigabit
|
|
Ethernet Media Access Controller (EMAC). The controller
|
|
supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
|
|
full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
|
|
low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
|
|
Precision Clock Synchronization Protocol.
|
|
|
|
source "drivers/net/ethernet/qualcomm/rmnet/Kconfig"
|
|
|
|
endif # NET_VENDOR_QUALCOMM
|