mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-16 08:44:21 +08:00
cb64ca5407
Set master->max_speed_hz then spi core will handle checking transfer speed. So we can remove the same checking in this driver. Also remove checking spi->chip_select in spi_qup_setup(), the checking is done by spi core. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Mark Brown <broonie@linaro.org>
824 lines
21 KiB
C
824 lines
21 KiB
C
/*
|
|
* Copyright (c) 2008-2014, The Linux foundation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License rev 2 and
|
|
* only rev 2 as published by the free Software foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or fITNESS fOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/err.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/list.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/spi/spi.h>
|
|
|
|
#define QUP_CONFIG 0x0000
|
|
#define QUP_STATE 0x0004
|
|
#define QUP_IO_M_MODES 0x0008
|
|
#define QUP_SW_RESET 0x000c
|
|
#define QUP_OPERATIONAL 0x0018
|
|
#define QUP_ERROR_FLAGS 0x001c
|
|
#define QUP_ERROR_FLAGS_EN 0x0020
|
|
#define QUP_OPERATIONAL_MASK 0x0028
|
|
#define QUP_HW_VERSION 0x0030
|
|
#define QUP_MX_OUTPUT_CNT 0x0100
|
|
#define QUP_OUTPUT_FIFO 0x0110
|
|
#define QUP_MX_WRITE_CNT 0x0150
|
|
#define QUP_MX_INPUT_CNT 0x0200
|
|
#define QUP_MX_READ_CNT 0x0208
|
|
#define QUP_INPUT_FIFO 0x0218
|
|
|
|
#define SPI_CONFIG 0x0300
|
|
#define SPI_IO_CONTROL 0x0304
|
|
#define SPI_ERROR_FLAGS 0x0308
|
|
#define SPI_ERROR_FLAGS_EN 0x030c
|
|
|
|
/* QUP_CONFIG fields */
|
|
#define QUP_CONFIG_SPI_MODE (1 << 8)
|
|
#define QUP_CONFIG_CLOCK_AUTO_GATE BIT(13)
|
|
#define QUP_CONFIG_NO_INPUT BIT(7)
|
|
#define QUP_CONFIG_NO_OUTPUT BIT(6)
|
|
#define QUP_CONFIG_N 0x001f
|
|
|
|
/* QUP_STATE fields */
|
|
#define QUP_STATE_VALID BIT(2)
|
|
#define QUP_STATE_RESET 0
|
|
#define QUP_STATE_RUN 1
|
|
#define QUP_STATE_PAUSE 3
|
|
#define QUP_STATE_MASK 3
|
|
#define QUP_STATE_CLEAR 2
|
|
|
|
#define QUP_HW_VERSION_2_1_1 0x20010001
|
|
|
|
/* QUP_IO_M_MODES fields */
|
|
#define QUP_IO_M_PACK_EN BIT(15)
|
|
#define QUP_IO_M_UNPACK_EN BIT(14)
|
|
#define QUP_IO_M_INPUT_MODE_MASK_SHIFT 12
|
|
#define QUP_IO_M_OUTPUT_MODE_MASK_SHIFT 10
|
|
#define QUP_IO_M_INPUT_MODE_MASK (3 << QUP_IO_M_INPUT_MODE_MASK_SHIFT)
|
|
#define QUP_IO_M_OUTPUT_MODE_MASK (3 << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT)
|
|
|
|
#define QUP_IO_M_OUTPUT_BLOCK_SIZE(x) (((x) & (0x03 << 0)) >> 0)
|
|
#define QUP_IO_M_OUTPUT_FIFO_SIZE(x) (((x) & (0x07 << 2)) >> 2)
|
|
#define QUP_IO_M_INPUT_BLOCK_SIZE(x) (((x) & (0x03 << 5)) >> 5)
|
|
#define QUP_IO_M_INPUT_FIFO_SIZE(x) (((x) & (0x07 << 7)) >> 7)
|
|
|
|
#define QUP_IO_M_MODE_FIFO 0
|
|
#define QUP_IO_M_MODE_BLOCK 1
|
|
#define QUP_IO_M_MODE_DMOV 2
|
|
#define QUP_IO_M_MODE_BAM 3
|
|
|
|
/* QUP_OPERATIONAL fields */
|
|
#define QUP_OP_MAX_INPUT_DONE_FLAG BIT(11)
|
|
#define QUP_OP_MAX_OUTPUT_DONE_FLAG BIT(10)
|
|
#define QUP_OP_IN_SERVICE_FLAG BIT(9)
|
|
#define QUP_OP_OUT_SERVICE_FLAG BIT(8)
|
|
#define QUP_OP_IN_FIFO_FULL BIT(7)
|
|
#define QUP_OP_OUT_FIFO_FULL BIT(6)
|
|
#define QUP_OP_IN_FIFO_NOT_EMPTY BIT(5)
|
|
#define QUP_OP_OUT_FIFO_NOT_EMPTY BIT(4)
|
|
|
|
/* QUP_ERROR_FLAGS and QUP_ERROR_FLAGS_EN fields */
|
|
#define QUP_ERROR_OUTPUT_OVER_RUN BIT(5)
|
|
#define QUP_ERROR_INPUT_UNDER_RUN BIT(4)
|
|
#define QUP_ERROR_OUTPUT_UNDER_RUN BIT(3)
|
|
#define QUP_ERROR_INPUT_OVER_RUN BIT(2)
|
|
|
|
/* SPI_CONFIG fields */
|
|
#define SPI_CONFIG_HS_MODE BIT(10)
|
|
#define SPI_CONFIG_INPUT_FIRST BIT(9)
|
|
#define SPI_CONFIG_LOOPBACK BIT(8)
|
|
|
|
/* SPI_IO_CONTROL fields */
|
|
#define SPI_IO_C_FORCE_CS BIT(11)
|
|
#define SPI_IO_C_CLK_IDLE_HIGH BIT(10)
|
|
#define SPI_IO_C_MX_CS_MODE BIT(8)
|
|
#define SPI_IO_C_CS_N_POLARITY_0 BIT(4)
|
|
#define SPI_IO_C_CS_SELECT(x) (((x) & 3) << 2)
|
|
#define SPI_IO_C_CS_SELECT_MASK 0x000c
|
|
#define SPI_IO_C_TRISTATE_CS BIT(1)
|
|
#define SPI_IO_C_NO_TRI_STATE BIT(0)
|
|
|
|
/* SPI_ERROR_FLAGS and SPI_ERROR_FLAGS_EN fields */
|
|
#define SPI_ERROR_CLK_OVER_RUN BIT(1)
|
|
#define SPI_ERROR_CLK_UNDER_RUN BIT(0)
|
|
|
|
#define SPI_NUM_CHIPSELECTS 4
|
|
|
|
/* high speed mode is when bus rate is greater then 26MHz */
|
|
#define SPI_HS_MIN_RATE 26000000
|
|
#define SPI_MAX_RATE 50000000
|
|
|
|
#define SPI_DELAY_THRESHOLD 1
|
|
#define SPI_DELAY_RETRY 10
|
|
|
|
struct spi_qup_device {
|
|
int select;
|
|
u16 mode;
|
|
};
|
|
|
|
struct spi_qup {
|
|
void __iomem *base;
|
|
struct device *dev;
|
|
struct clk *cclk; /* core clock */
|
|
struct clk *iclk; /* interface clock */
|
|
int irq;
|
|
spinlock_t lock;
|
|
|
|
int in_fifo_sz;
|
|
int out_fifo_sz;
|
|
int in_blk_sz;
|
|
int out_blk_sz;
|
|
|
|
struct spi_transfer *xfer;
|
|
struct completion done;
|
|
int error;
|
|
int w_size; /* bytes per SPI word */
|
|
int tx_bytes;
|
|
int rx_bytes;
|
|
};
|
|
|
|
|
|
static inline bool spi_qup_is_valid_state(struct spi_qup *controller)
|
|
{
|
|
u32 opstate = readl_relaxed(controller->base + QUP_STATE);
|
|
|
|
return opstate & QUP_STATE_VALID;
|
|
}
|
|
|
|
static int spi_qup_set_state(struct spi_qup *controller, u32 state)
|
|
{
|
|
unsigned long loop;
|
|
u32 cur_state;
|
|
|
|
loop = 0;
|
|
while (!spi_qup_is_valid_state(controller)) {
|
|
|
|
usleep_range(SPI_DELAY_THRESHOLD, SPI_DELAY_THRESHOLD * 2);
|
|
|
|
if (++loop > SPI_DELAY_RETRY)
|
|
return -EIO;
|
|
}
|
|
|
|
if (loop)
|
|
dev_dbg(controller->dev, "invalid state for %ld,us %d\n",
|
|
loop, state);
|
|
|
|
cur_state = readl_relaxed(controller->base + QUP_STATE);
|
|
/*
|
|
* Per spec: for PAUSE_STATE to RESET_STATE, two writes
|
|
* of (b10) are required
|
|
*/
|
|
if (((cur_state & QUP_STATE_MASK) == QUP_STATE_PAUSE) &&
|
|
(state == QUP_STATE_RESET)) {
|
|
writel_relaxed(QUP_STATE_CLEAR, controller->base + QUP_STATE);
|
|
writel_relaxed(QUP_STATE_CLEAR, controller->base + QUP_STATE);
|
|
} else {
|
|
cur_state &= ~QUP_STATE_MASK;
|
|
cur_state |= state;
|
|
writel_relaxed(cur_state, controller->base + QUP_STATE);
|
|
}
|
|
|
|
loop = 0;
|
|
while (!spi_qup_is_valid_state(controller)) {
|
|
|
|
usleep_range(SPI_DELAY_THRESHOLD, SPI_DELAY_THRESHOLD * 2);
|
|
|
|
if (++loop > SPI_DELAY_RETRY)
|
|
return -EIO;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
static void spi_qup_fifo_read(struct spi_qup *controller,
|
|
struct spi_transfer *xfer)
|
|
{
|
|
u8 *rx_buf = xfer->rx_buf;
|
|
u32 word, state;
|
|
int idx, shift, w_size;
|
|
|
|
w_size = controller->w_size;
|
|
|
|
while (controller->rx_bytes < xfer->len) {
|
|
|
|
state = readl_relaxed(controller->base + QUP_OPERATIONAL);
|
|
if (0 == (state & QUP_OP_IN_FIFO_NOT_EMPTY))
|
|
break;
|
|
|
|
word = readl_relaxed(controller->base + QUP_INPUT_FIFO);
|
|
|
|
if (!rx_buf) {
|
|
controller->rx_bytes += w_size;
|
|
continue;
|
|
}
|
|
|
|
for (idx = 0; idx < w_size; idx++, controller->rx_bytes++) {
|
|
/*
|
|
* The data format depends on bytes per SPI word:
|
|
* 4 bytes: 0x12345678
|
|
* 2 bytes: 0x00001234
|
|
* 1 byte : 0x00000012
|
|
*/
|
|
shift = BITS_PER_BYTE;
|
|
shift *= (w_size - idx - 1);
|
|
rx_buf[controller->rx_bytes] = word >> shift;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void spi_qup_fifo_write(struct spi_qup *controller,
|
|
struct spi_transfer *xfer)
|
|
{
|
|
const u8 *tx_buf = xfer->tx_buf;
|
|
u32 word, state, data;
|
|
int idx, w_size;
|
|
|
|
w_size = controller->w_size;
|
|
|
|
while (controller->tx_bytes < xfer->len) {
|
|
|
|
state = readl_relaxed(controller->base + QUP_OPERATIONAL);
|
|
if (state & QUP_OP_OUT_FIFO_FULL)
|
|
break;
|
|
|
|
word = 0;
|
|
for (idx = 0; idx < w_size; idx++, controller->tx_bytes++) {
|
|
|
|
if (!tx_buf) {
|
|
controller->tx_bytes += w_size;
|
|
break;
|
|
}
|
|
|
|
data = tx_buf[controller->tx_bytes];
|
|
word |= data << (BITS_PER_BYTE * (3 - idx));
|
|
}
|
|
|
|
writel_relaxed(word, controller->base + QUP_OUTPUT_FIFO);
|
|
}
|
|
}
|
|
|
|
static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
|
|
{
|
|
struct spi_qup *controller = dev_id;
|
|
struct spi_transfer *xfer;
|
|
u32 opflags, qup_err, spi_err;
|
|
unsigned long flags;
|
|
int error = 0;
|
|
|
|
spin_lock_irqsave(&controller->lock, flags);
|
|
xfer = controller->xfer;
|
|
controller->xfer = NULL;
|
|
spin_unlock_irqrestore(&controller->lock, flags);
|
|
|
|
qup_err = readl_relaxed(controller->base + QUP_ERROR_FLAGS);
|
|
spi_err = readl_relaxed(controller->base + SPI_ERROR_FLAGS);
|
|
opflags = readl_relaxed(controller->base + QUP_OPERATIONAL);
|
|
|
|
writel_relaxed(qup_err, controller->base + QUP_ERROR_FLAGS);
|
|
writel_relaxed(spi_err, controller->base + SPI_ERROR_FLAGS);
|
|
writel_relaxed(opflags, controller->base + QUP_OPERATIONAL);
|
|
|
|
if (!xfer) {
|
|
dev_err_ratelimited(controller->dev, "unexpected irq %x08 %x08 %x08\n",
|
|
qup_err, spi_err, opflags);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
if (qup_err) {
|
|
if (qup_err & QUP_ERROR_OUTPUT_OVER_RUN)
|
|
dev_warn(controller->dev, "OUTPUT_OVER_RUN\n");
|
|
if (qup_err & QUP_ERROR_INPUT_UNDER_RUN)
|
|
dev_warn(controller->dev, "INPUT_UNDER_RUN\n");
|
|
if (qup_err & QUP_ERROR_OUTPUT_UNDER_RUN)
|
|
dev_warn(controller->dev, "OUTPUT_UNDER_RUN\n");
|
|
if (qup_err & QUP_ERROR_INPUT_OVER_RUN)
|
|
dev_warn(controller->dev, "INPUT_OVER_RUN\n");
|
|
|
|
error = -EIO;
|
|
}
|
|
|
|
if (spi_err) {
|
|
if (spi_err & SPI_ERROR_CLK_OVER_RUN)
|
|
dev_warn(controller->dev, "CLK_OVER_RUN\n");
|
|
if (spi_err & SPI_ERROR_CLK_UNDER_RUN)
|
|
dev_warn(controller->dev, "CLK_UNDER_RUN\n");
|
|
|
|
error = -EIO;
|
|
}
|
|
|
|
if (opflags & QUP_OP_IN_SERVICE_FLAG)
|
|
spi_qup_fifo_read(controller, xfer);
|
|
|
|
if (opflags & QUP_OP_OUT_SERVICE_FLAG)
|
|
spi_qup_fifo_write(controller, xfer);
|
|
|
|
spin_lock_irqsave(&controller->lock, flags);
|
|
controller->error = error;
|
|
controller->xfer = xfer;
|
|
spin_unlock_irqrestore(&controller->lock, flags);
|
|
|
|
if (controller->rx_bytes == xfer->len || error)
|
|
complete(&controller->done);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
|
|
/* set clock freq ... bits per word */
|
|
static int spi_qup_io_config(struct spi_qup *controller,
|
|
struct spi_qup_device *chip,
|
|
struct spi_transfer *xfer)
|
|
{
|
|
u32 config, iomode, mode;
|
|
int ret, n_words, w_size;
|
|
|
|
if (chip->mode & SPI_LOOP && xfer->len > controller->in_fifo_sz) {
|
|
dev_err(controller->dev, "too big size for loopback %d > %d\n",
|
|
xfer->len, controller->in_fifo_sz);
|
|
return -EIO;
|
|
}
|
|
|
|
ret = clk_set_rate(controller->cclk, xfer->speed_hz);
|
|
if (ret) {
|
|
dev_err(controller->dev, "fail to set frequency %d",
|
|
xfer->speed_hz);
|
|
return -EIO;
|
|
}
|
|
|
|
if (spi_qup_set_state(controller, QUP_STATE_RESET)) {
|
|
dev_err(controller->dev, "cannot set RESET state\n");
|
|
return -EIO;
|
|
}
|
|
|
|
w_size = 4;
|
|
if (xfer->bits_per_word <= 8)
|
|
w_size = 1;
|
|
else if (xfer->bits_per_word <= 16)
|
|
w_size = 2;
|
|
|
|
n_words = xfer->len / w_size;
|
|
controller->w_size = w_size;
|
|
|
|
if (n_words <= controller->in_fifo_sz) {
|
|
mode = QUP_IO_M_MODE_FIFO;
|
|
writel_relaxed(n_words, controller->base + QUP_MX_READ_CNT);
|
|
writel_relaxed(n_words, controller->base + QUP_MX_WRITE_CNT);
|
|
/* must be zero for FIFO */
|
|
writel_relaxed(0, controller->base + QUP_MX_INPUT_CNT);
|
|
writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
|
|
} else {
|
|
mode = QUP_IO_M_MODE_BLOCK;
|
|
writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
|
|
writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
|
|
/* must be zero for BLOCK and BAM */
|
|
writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
|
|
writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
|
|
}
|
|
|
|
iomode = readl_relaxed(controller->base + QUP_IO_M_MODES);
|
|
/* Set input and output transfer mode */
|
|
iomode &= ~(QUP_IO_M_INPUT_MODE_MASK | QUP_IO_M_OUTPUT_MODE_MASK);
|
|
iomode &= ~(QUP_IO_M_PACK_EN | QUP_IO_M_UNPACK_EN);
|
|
iomode |= (mode << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT);
|
|
iomode |= (mode << QUP_IO_M_INPUT_MODE_MASK_SHIFT);
|
|
|
|
writel_relaxed(iomode, controller->base + QUP_IO_M_MODES);
|
|
|
|
config = readl_relaxed(controller->base + SPI_CONFIG);
|
|
|
|
if (chip->mode & SPI_LOOP)
|
|
config |= SPI_CONFIG_LOOPBACK;
|
|
else
|
|
config &= ~SPI_CONFIG_LOOPBACK;
|
|
|
|
if (chip->mode & SPI_CPHA)
|
|
config &= ~SPI_CONFIG_INPUT_FIRST;
|
|
else
|
|
config |= SPI_CONFIG_INPUT_FIRST;
|
|
|
|
/*
|
|
* HS_MODE improves signal stability for spi-clk high rates,
|
|
* but is invalid in loop back mode.
|
|
*/
|
|
if ((xfer->speed_hz >= SPI_HS_MIN_RATE) && !(chip->mode & SPI_LOOP))
|
|
config |= SPI_CONFIG_HS_MODE;
|
|
else
|
|
config &= ~SPI_CONFIG_HS_MODE;
|
|
|
|
writel_relaxed(config, controller->base + SPI_CONFIG);
|
|
|
|
config = readl_relaxed(controller->base + QUP_CONFIG);
|
|
config &= ~(QUP_CONFIG_NO_INPUT | QUP_CONFIG_NO_OUTPUT | QUP_CONFIG_N);
|
|
config |= xfer->bits_per_word - 1;
|
|
config |= QUP_CONFIG_SPI_MODE;
|
|
writel_relaxed(config, controller->base + QUP_CONFIG);
|
|
|
|
writel_relaxed(0, controller->base + QUP_OPERATIONAL_MASK);
|
|
return 0;
|
|
}
|
|
|
|
static void spi_qup_set_cs(struct spi_device *spi, bool enable)
|
|
{
|
|
struct spi_qup *controller = spi_master_get_devdata(spi->master);
|
|
struct spi_qup_device *chip = spi_get_ctldata(spi);
|
|
|
|
u32 iocontol, mask;
|
|
|
|
iocontol = readl_relaxed(controller->base + SPI_IO_CONTROL);
|
|
|
|
/* Disable auto CS toggle and use manual */
|
|
iocontol &= ~SPI_IO_C_MX_CS_MODE;
|
|
iocontol |= SPI_IO_C_FORCE_CS;
|
|
|
|
iocontol &= ~SPI_IO_C_CS_SELECT_MASK;
|
|
iocontol |= SPI_IO_C_CS_SELECT(chip->select);
|
|
|
|
mask = SPI_IO_C_CS_N_POLARITY_0 << chip->select;
|
|
|
|
if (enable)
|
|
iocontol |= mask;
|
|
else
|
|
iocontol &= ~mask;
|
|
|
|
writel_relaxed(iocontol, controller->base + SPI_IO_CONTROL);
|
|
}
|
|
|
|
static int spi_qup_transfer_one(struct spi_master *master,
|
|
struct spi_device *spi,
|
|
struct spi_transfer *xfer)
|
|
{
|
|
struct spi_qup *controller = spi_master_get_devdata(master);
|
|
struct spi_qup_device *chip = spi_get_ctldata(spi);
|
|
unsigned long timeout, flags;
|
|
int ret = -EIO;
|
|
|
|
ret = spi_qup_io_config(controller, chip, xfer);
|
|
if (ret)
|
|
return ret;
|
|
|
|
timeout = DIV_ROUND_UP(xfer->speed_hz, MSEC_PER_SEC);
|
|
timeout = DIV_ROUND_UP(xfer->len * 8, timeout);
|
|
timeout = 100 * msecs_to_jiffies(timeout);
|
|
|
|
reinit_completion(&controller->done);
|
|
|
|
spin_lock_irqsave(&controller->lock, flags);
|
|
controller->xfer = xfer;
|
|
controller->error = 0;
|
|
controller->rx_bytes = 0;
|
|
controller->tx_bytes = 0;
|
|
spin_unlock_irqrestore(&controller->lock, flags);
|
|
|
|
if (spi_qup_set_state(controller, QUP_STATE_RUN)) {
|
|
dev_warn(controller->dev, "cannot set RUN state\n");
|
|
goto exit;
|
|
}
|
|
|
|
if (spi_qup_set_state(controller, QUP_STATE_PAUSE)) {
|
|
dev_warn(controller->dev, "cannot set PAUSE state\n");
|
|
goto exit;
|
|
}
|
|
|
|
spi_qup_fifo_write(controller, xfer);
|
|
|
|
if (spi_qup_set_state(controller, QUP_STATE_RUN)) {
|
|
dev_warn(controller->dev, "cannot set EXECUTE state\n");
|
|
goto exit;
|
|
}
|
|
|
|
if (!wait_for_completion_timeout(&controller->done, timeout))
|
|
ret = -ETIMEDOUT;
|
|
exit:
|
|
spi_qup_set_state(controller, QUP_STATE_RESET);
|
|
spin_lock_irqsave(&controller->lock, flags);
|
|
controller->xfer = NULL;
|
|
if (!ret)
|
|
ret = controller->error;
|
|
spin_unlock_irqrestore(&controller->lock, flags);
|
|
return ret;
|
|
}
|
|
|
|
static int spi_qup_setup(struct spi_device *spi)
|
|
{
|
|
struct spi_qup *controller = spi_master_get_devdata(spi->master);
|
|
struct spi_qup_device *chip = spi_get_ctldata(spi);
|
|
|
|
if (!chip) {
|
|
/* First setup */
|
|
chip = kzalloc(sizeof(*chip), GFP_KERNEL);
|
|
if (!chip) {
|
|
dev_err(controller->dev, "no memory for chip data\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
chip->mode = spi->mode;
|
|
chip->select = spi->chip_select;
|
|
spi_set_ctldata(spi, chip);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void spi_qup_cleanup(struct spi_device *spi)
|
|
{
|
|
struct spi_qup_device *chip = spi_get_ctldata(spi);
|
|
|
|
if (!chip)
|
|
return;
|
|
|
|
spi_set_ctldata(spi, NULL);
|
|
kfree(chip);
|
|
}
|
|
|
|
static int spi_qup_probe(struct platform_device *pdev)
|
|
{
|
|
struct spi_master *master;
|
|
struct clk *iclk, *cclk;
|
|
struct spi_qup *controller;
|
|
struct resource *res;
|
|
struct device *dev;
|
|
void __iomem *base;
|
|
u32 data, max_freq, iomode;
|
|
int ret, irq, size;
|
|
|
|
dev = &pdev->dev;
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
base = devm_ioremap_resource(dev, res);
|
|
if (IS_ERR(base))
|
|
return PTR_ERR(base);
|
|
|
|
irq = platform_get_irq(pdev, 0);
|
|
|
|
if (irq < 0)
|
|
return irq;
|
|
|
|
cclk = devm_clk_get(dev, "core");
|
|
if (IS_ERR(cclk))
|
|
return PTR_ERR(cclk);
|
|
|
|
iclk = devm_clk_get(dev, "iface");
|
|
if (IS_ERR(iclk))
|
|
return PTR_ERR(iclk);
|
|
|
|
/* This is optional parameter */
|
|
if (of_property_read_u32(dev->of_node, "spi-max-frequency", &max_freq))
|
|
max_freq = SPI_MAX_RATE;
|
|
|
|
if (!max_freq || max_freq > SPI_MAX_RATE) {
|
|
dev_err(dev, "invalid clock frequency %d\n", max_freq);
|
|
return -ENXIO;
|
|
}
|
|
|
|
ret = clk_prepare_enable(cclk);
|
|
if (ret) {
|
|
dev_err(dev, "cannot enable core clock\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = clk_prepare_enable(iclk);
|
|
if (ret) {
|
|
clk_disable_unprepare(cclk);
|
|
dev_err(dev, "cannot enable iface clock\n");
|
|
return ret;
|
|
}
|
|
|
|
data = readl_relaxed(base + QUP_HW_VERSION);
|
|
|
|
if (data < QUP_HW_VERSION_2_1_1) {
|
|
clk_disable_unprepare(cclk);
|
|
clk_disable_unprepare(iclk);
|
|
dev_err(dev, "v.%08x is not supported\n", data);
|
|
return -ENXIO;
|
|
}
|
|
|
|
master = spi_alloc_master(dev, sizeof(struct spi_qup));
|
|
if (!master) {
|
|
clk_disable_unprepare(cclk);
|
|
clk_disable_unprepare(iclk);
|
|
dev_err(dev, "cannot allocate master\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
master->bus_num = pdev->id;
|
|
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
|
|
master->num_chipselect = SPI_NUM_CHIPSELECTS;
|
|
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
|
|
master->max_speed_hz = max_freq;
|
|
master->setup = spi_qup_setup;
|
|
master->cleanup = spi_qup_cleanup;
|
|
master->set_cs = spi_qup_set_cs;
|
|
master->transfer_one = spi_qup_transfer_one;
|
|
master->dev.of_node = pdev->dev.of_node;
|
|
master->auto_runtime_pm = true;
|
|
|
|
platform_set_drvdata(pdev, master);
|
|
|
|
controller = spi_master_get_devdata(master);
|
|
|
|
controller->dev = dev;
|
|
controller->base = base;
|
|
controller->iclk = iclk;
|
|
controller->cclk = cclk;
|
|
controller->irq = irq;
|
|
|
|
spin_lock_init(&controller->lock);
|
|
init_completion(&controller->done);
|
|
|
|
iomode = readl_relaxed(base + QUP_IO_M_MODES);
|
|
|
|
size = QUP_IO_M_OUTPUT_BLOCK_SIZE(iomode);
|
|
if (size)
|
|
controller->out_blk_sz = size * 16;
|
|
else
|
|
controller->out_blk_sz = 4;
|
|
|
|
size = QUP_IO_M_INPUT_BLOCK_SIZE(iomode);
|
|
if (size)
|
|
controller->in_blk_sz = size * 16;
|
|
else
|
|
controller->in_blk_sz = 4;
|
|
|
|
size = QUP_IO_M_OUTPUT_FIFO_SIZE(iomode);
|
|
controller->out_fifo_sz = controller->out_blk_sz * (2 << size);
|
|
|
|
size = QUP_IO_M_INPUT_FIFO_SIZE(iomode);
|
|
controller->in_fifo_sz = controller->in_blk_sz * (2 << size);
|
|
|
|
dev_info(dev, "v.%08x IN:block:%d, fifo:%d, OUT:block:%d, fifo:%d\n",
|
|
data, controller->in_blk_sz, controller->in_fifo_sz,
|
|
controller->out_blk_sz, controller->out_fifo_sz);
|
|
|
|
writel_relaxed(1, base + QUP_SW_RESET);
|
|
|
|
ret = spi_qup_set_state(controller, QUP_STATE_RESET);
|
|
if (ret) {
|
|
dev_err(dev, "cannot set RESET state\n");
|
|
goto error;
|
|
}
|
|
|
|
writel_relaxed(0, base + QUP_OPERATIONAL);
|
|
writel_relaxed(0, base + QUP_IO_M_MODES);
|
|
writel_relaxed(0, base + QUP_OPERATIONAL_MASK);
|
|
writel_relaxed(SPI_ERROR_CLK_UNDER_RUN | SPI_ERROR_CLK_OVER_RUN,
|
|
base + SPI_ERROR_FLAGS_EN);
|
|
|
|
writel_relaxed(0, base + SPI_CONFIG);
|
|
writel_relaxed(SPI_IO_C_NO_TRI_STATE, base + SPI_IO_CONTROL);
|
|
|
|
ret = devm_request_irq(dev, irq, spi_qup_qup_irq,
|
|
IRQF_TRIGGER_HIGH, pdev->name, controller);
|
|
if (ret)
|
|
goto error;
|
|
|
|
ret = devm_spi_register_master(dev, master);
|
|
if (ret)
|
|
goto error;
|
|
|
|
pm_runtime_set_autosuspend_delay(dev, MSEC_PER_SEC);
|
|
pm_runtime_use_autosuspend(dev);
|
|
pm_runtime_set_active(dev);
|
|
pm_runtime_enable(dev);
|
|
return 0;
|
|
|
|
error:
|
|
clk_disable_unprepare(cclk);
|
|
clk_disable_unprepare(iclk);
|
|
spi_master_put(master);
|
|
return ret;
|
|
}
|
|
|
|
#ifdef CONFIG_PM_RUNTIME
|
|
static int spi_qup_pm_suspend_runtime(struct device *device)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(device);
|
|
struct spi_qup *controller = spi_master_get_devdata(master);
|
|
u32 config;
|
|
|
|
/* Enable clocks auto gaiting */
|
|
config = readl(controller->base + QUP_CONFIG);
|
|
config |= QUP_CLOCK_AUTO_GATE;
|
|
writel_relaxed(config, controller->base + QUP_CONFIG);
|
|
return 0;
|
|
}
|
|
|
|
static int spi_qup_pm_resume_runtime(struct device *device)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(device);
|
|
struct spi_qup *controller = spi_master_get_devdata(master);
|
|
u32 config;
|
|
|
|
/* Disable clocks auto gaiting */
|
|
config = readl_relaxed(controller->base + QUP_CONFIG);
|
|
config &= ~QUP_CLOCK_AUTO_GATE;
|
|
writel_relaxed(config, controller->base + QUP_CONFIG);
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_PM_RUNTIME */
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static int spi_qup_suspend(struct device *device)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(device);
|
|
struct spi_qup *controller = spi_master_get_devdata(master);
|
|
int ret;
|
|
|
|
ret = spi_master_suspend(master);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = spi_qup_set_state(controller, QUP_STATE_RESET);
|
|
if (ret)
|
|
return ret;
|
|
|
|
clk_disable_unprepare(controller->cclk);
|
|
clk_disable_unprepare(controller->iclk);
|
|
return 0;
|
|
}
|
|
|
|
static int spi_qup_resume(struct device *device)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(device);
|
|
struct spi_qup *controller = spi_master_get_devdata(master);
|
|
int ret;
|
|
|
|
ret = clk_prepare_enable(controller->iclk);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = clk_prepare_enable(controller->cclk);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = spi_qup_set_state(controller, QUP_STATE_RESET);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return spi_master_resume(master);
|
|
}
|
|
#endif /* CONFIG_PM_SLEEP */
|
|
|
|
static int spi_qup_remove(struct platform_device *pdev)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(&pdev->dev);
|
|
struct spi_qup *controller = spi_master_get_devdata(master);
|
|
int ret;
|
|
|
|
ret = pm_runtime_get_sync(&pdev->dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = spi_qup_set_state(controller, QUP_STATE_RESET);
|
|
if (ret)
|
|
return ret;
|
|
|
|
clk_disable_unprepare(controller->cclk);
|
|
clk_disable_unprepare(controller->iclk);
|
|
|
|
pm_runtime_put_noidle(&pdev->dev);
|
|
pm_runtime_disable(&pdev->dev);
|
|
return 0;
|
|
}
|
|
|
|
static struct of_device_id spi_qup_dt_match[] = {
|
|
{ .compatible = "qcom,spi-qup-v2.1.1", },
|
|
{ .compatible = "qcom,spi-qup-v2.2.1", },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, spi_qup_dt_match);
|
|
|
|
static const struct dev_pm_ops spi_qup_dev_pm_ops = {
|
|
SET_SYSTEM_SLEEP_PM_OPS(spi_qup_suspend, spi_qup_resume)
|
|
SET_RUNTIME_PM_OPS(spi_qup_pm_suspend_runtime,
|
|
spi_qup_pm_resume_runtime,
|
|
NULL)
|
|
};
|
|
|
|
static struct platform_driver spi_qup_driver = {
|
|
.driver = {
|
|
.name = "spi_qup",
|
|
.owner = THIS_MODULE,
|
|
.pm = &spi_qup_dev_pm_ops,
|
|
.of_match_table = spi_qup_dt_match,
|
|
},
|
|
.probe = spi_qup_probe,
|
|
.remove = spi_qup_remove,
|
|
};
|
|
module_platform_driver(spi_qup_driver);
|
|
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_VERSION("0.4");
|
|
MODULE_ALIAS("platform:spi_qup");
|