mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-12 21:44:06 +08:00
f710b49e3c
Convert the SPMI bus documentation to JSON/yaml. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Link: https://lore.kernel.org/r/ee4c4ca9f29a39f6af772b3a526a996176499da3.1598415179.git.mchehab+huawei@kernel.org [robh: Correct maintainer, unit-address should be hex] Signed-off-by: Rob Herring <robh@kernel.org>
66 lines
2.5 KiB
Plaintext
66 lines
2.5 KiB
Plaintext
Qualcomm SPMI Controller (PMIC Arbiter)
|
|
|
|
The SPMI PMIC Arbiter is found on Snapdragon chipsets. It is an SPMI
|
|
controller with wrapping arbitration logic to allow for multiple on-chip
|
|
devices to control a single SPMI master.
|
|
|
|
The PMIC Arbiter can also act as an interrupt controller, providing interrupts
|
|
to slave devices.
|
|
|
|
See Documentation/devicetree/bindings/spmi/spmi.yaml for the generic SPMI
|
|
controller binding requirements for child nodes.
|
|
|
|
See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
|
|
generic interrupt controller binding documentation.
|
|
|
|
Required properties:
|
|
- compatible : should be "qcom,spmi-pmic-arb".
|
|
- reg-names : must contain:
|
|
"core" - core registers
|
|
"intr" - interrupt controller registers
|
|
"cnfg" - configuration registers
|
|
Registers used only for V2 PMIC Arbiter:
|
|
"chnls" - tx-channel per virtual slave registers.
|
|
"obsrvr" - rx-channel (called observer) per virtual slave registers.
|
|
|
|
- reg : address + size pairs describing the PMIC arb register sets; order must
|
|
correspond with the order of entries in reg-names
|
|
- #address-cells : must be set to 2
|
|
- #size-cells : must be set to 0
|
|
- qcom,ee : indicates the active Execution Environment identifier (0-5)
|
|
- qcom,channel : which of the PMIC Arb provided channels to use for accesses (0-5)
|
|
- interrupts : interrupt list for the PMIC Arb controller, must contain a
|
|
single interrupt entry for the peripheral interrupt
|
|
- interrupt-names : corresponding interrupt names for the interrupts
|
|
listed in the 'interrupts' property, must contain:
|
|
"periph_irq" - summary interrupt for PMIC peripherals
|
|
- interrupt-controller : boolean indicator that the PMIC arbiter is an interrupt controller
|
|
- #interrupt-cells : must be set to 4. Interrupts are specified as a 4-tuple:
|
|
cell 1: slave ID for the requested interrupt (0-15)
|
|
cell 2: peripheral ID for requested interrupt (0-255)
|
|
cell 3: the requested peripheral interrupt (0-7)
|
|
cell 4: interrupt flags indicating level-sense information, as defined in
|
|
dt-bindings/interrupt-controller/irq.h
|
|
|
|
Example:
|
|
|
|
spmi {
|
|
compatible = "qcom,spmi-pmic-arb";
|
|
reg-names = "core", "intr", "cnfg";
|
|
reg = <0xfc4cf000 0x1000>,
|
|
<0xfc4cb000 0x1000>,
|
|
<0xfc4ca000 0x1000>;
|
|
|
|
interrupt-names = "periph_irq";
|
|
interrupts = <0 190 0>;
|
|
|
|
qcom,ee = <0>;
|
|
qcom,channel = <0>;
|
|
|
|
#address-cells = <2>;
|
|
#size-cells = <0>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <4>;
|
|
};
|