mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-05 01:54:09 +08:00
bcc567e311
When user interrupts ongoing transfers the dmatest may end up with console lockup, oops, or data mismatch. This patch prevents user to abort any ongoing test. Documentation is updated accordingly. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reported-by: Will Deacon <will.deacon@arm.com> Tested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
82 lines
2.8 KiB
Plaintext
82 lines
2.8 KiB
Plaintext
DMA Test Guide
|
|
==============
|
|
|
|
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
|
|
This small document introduces how to test DMA drivers using dmatest module.
|
|
|
|
Part 1 - How to build the test module
|
|
|
|
The menuconfig contains an option that could be found by following path:
|
|
Device Drivers -> DMA Engine support -> DMA Test client
|
|
|
|
In the configuration file the option called CONFIG_DMATEST. The dmatest could
|
|
be built as module or inside kernel. Let's consider those cases.
|
|
|
|
Part 2 - When dmatest is built as a module...
|
|
|
|
After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest
|
|
folder with nodes will be created. They are the same as module parameters with
|
|
addition of the 'run' node that controls run and stop phases of the test.
|
|
|
|
Note that in this case test will not run on load automatically.
|
|
|
|
Example of usage:
|
|
% echo dma0chan0 > /sys/kernel/debug/dmatest/channel
|
|
% echo 2000 > /sys/kernel/debug/dmatest/timeout
|
|
% echo 1 > /sys/kernel/debug/dmatest/iterations
|
|
% echo 1 > /sys/kernel/debug/dmatest/run
|
|
|
|
Hint: available channel list could be extracted by running the following
|
|
command:
|
|
% ls -1 /sys/class/dma/
|
|
|
|
After a while you will start to get messages about current status or error like
|
|
in the original code.
|
|
|
|
Note that running a new test will not stop any in progress test.
|
|
|
|
The following command should return actual state of the test.
|
|
% cat /sys/kernel/debug/dmatest/run
|
|
|
|
To wait for test done the user may perform a busy loop that checks the state.
|
|
|
|
% while [ $(cat /sys/kernel/debug/dmatest/run) = "Y" ]
|
|
> do
|
|
> echo -n "."
|
|
> sleep 1
|
|
> done
|
|
> echo
|
|
|
|
Part 3 - When built-in in the kernel...
|
|
|
|
The module parameters that is supplied to the kernel command line will be used
|
|
for the first performed test. After user gets a control, the test could be
|
|
re-run with the same or different parameters. For the details see the above
|
|
section "Part 2 - When dmatest is built as a module..."
|
|
|
|
In both cases the module parameters are used as initial values for the test case.
|
|
You always could check them at run-time by running
|
|
% grep -H . /sys/module/dmatest/parameters/*
|
|
|
|
Part 4 - Gathering the test results
|
|
|
|
The module provides a storage for the test results in the memory. The gathered
|
|
data could be used after test is done.
|
|
|
|
The special file 'results' in the debugfs represents gathered data of the in
|
|
progress test. The messages collected are printed to the kernel log as well.
|
|
|
|
Example of output:
|
|
% cat /sys/kernel/debug/dmatest/results
|
|
dma0chan0-copy0: #1: No errors with src_off=0x7bf dst_off=0x8ad len=0x3fea (0)
|
|
|
|
The message format is unified across the different types of errors. A number in
|
|
the parens represents additional information, e.g. error code, error counter,
|
|
or status.
|
|
|
|
Comparison between buffers is stored to the dedicated structure.
|
|
|
|
Note that the verify result is now accessible only via file 'results' in the
|
|
debugfs.
|