mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-28 05:24:47 +08:00
d522af581c
Impact: driver could possibly stomp on resources outside of its scope {mchehab@redhat.com: I got two versions of the same patch (identical, except for whitespacing). One authored by Andy Burns and another authored by Suresh Siddha. Due to that, I'm applying the one that has less CodingStyle errors. I'm also adding both comments and the SOB's for both patches, since they are both interesting} Suresh Siddha commented: Alexey Fisher reported: > resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000 > 0xcfefffff PCI Bus 0000:01 BAR base is located in the middle of the 4K page and the hardcoded size argument makes the request span two pages causing the conflict. Fix the hard coded size argument in ioremap(). Andy Burns commented: I have already sent this patch on the linux-dvb list, but it didn't get much attention, so re-sending direct, I hope you all don't mind. While attempting to run mythtv in a xen domU, I encountered problems loading the driver for my saa7134 card, with an error from ioremap(). This error was due to the driver allocating an incorrectly sized mmio area, which was trapped by xen's permission checks, but this would go un-noticed on a kernel without xen. My card has a 1K sized mmio area, I've had information that other cards have 2K areas, perhaps others have different sizes, yet the driver always attempts to map 4K. I realise that the granularity of mapping is the page size, which typically would be 4K, but unless the card's base address happens to fall on a 4K boundary (mine does not) then the base+4K will end up spanning two pages, and this is when the error occurs under xen. My patch uses the pci_resource_len macro to determine the size required for the user's particular card, instead of the hardcoded 4K value. I've tested with a couple of printk() inside ioremap() that the start address and size do get rounded to the closest page boundary. With this patch I am able to successfully load the saa7134 driver and run mythtv under xen with my card, subject to correct pollirq settings in case of shared IRQ, I am still seeing occasional DMA panics, which I think are related to swiotlb handling by dom0/domU, usually the panic occurs when changing mux, once tuned to a mux, 12 hour continuous recordings are possible without errors. Reported-by: Alexey Fisher <bug-track@fisher-privat.net> Tested-by: Alexey Fisher <bug-track@fisher-privat.net> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Andy Burns <andy@burns.net> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1325 lines
35 KiB
C
1325 lines
35 KiB
C
/*
|
|
*
|
|
* device driver for philips saa7134 based TV cards
|
|
* driver core
|
|
*
|
|
* (c) 2001-03 Gerd Knorr <kraxel@bytesex.org> [SuSE Labs]
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
|
|
#include <linux/init.h>
|
|
#include <linux/list.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/kmod.h>
|
|
#include <linux/sound.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/pm.h>
|
|
|
|
#include "saa7134-reg.h"
|
|
#include "saa7134.h"
|
|
|
|
MODULE_DESCRIPTION("v4l2 driver module for saa7130/34 based TV cards");
|
|
MODULE_AUTHOR("Gerd Knorr <kraxel@bytesex.org> [SuSE Labs]");
|
|
MODULE_LICENSE("GPL");
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
static unsigned int irq_debug;
|
|
module_param(irq_debug, int, 0644);
|
|
MODULE_PARM_DESC(irq_debug,"enable debug messages [IRQ handler]");
|
|
|
|
static unsigned int core_debug;
|
|
module_param(core_debug, int, 0644);
|
|
MODULE_PARM_DESC(core_debug,"enable debug messages [core]");
|
|
|
|
static unsigned int gpio_tracking;
|
|
module_param(gpio_tracking, int, 0644);
|
|
MODULE_PARM_DESC(gpio_tracking,"enable debug messages [gpio]");
|
|
|
|
static unsigned int alsa;
|
|
module_param(alsa, int, 0644);
|
|
MODULE_PARM_DESC(alsa,"enable ALSA DMA sound [dmasound]");
|
|
|
|
static unsigned int oss;
|
|
module_param(oss, int, 0644);
|
|
MODULE_PARM_DESC(oss,"enable OSS DMA sound [dmasound]");
|
|
|
|
static unsigned int latency = UNSET;
|
|
module_param(latency, int, 0444);
|
|
MODULE_PARM_DESC(latency,"pci latency timer");
|
|
|
|
int saa7134_no_overlay=-1;
|
|
module_param_named(no_overlay, saa7134_no_overlay, int, 0444);
|
|
MODULE_PARM_DESC(no_overlay,"allow override overlay default (0 disables, 1 enables)"
|
|
" [some VIA/SIS chipsets are known to have problem with overlay]");
|
|
|
|
static unsigned int video_nr[] = {[0 ... (SAA7134_MAXBOARDS - 1)] = UNSET };
|
|
static unsigned int vbi_nr[] = {[0 ... (SAA7134_MAXBOARDS - 1)] = UNSET };
|
|
static unsigned int radio_nr[] = {[0 ... (SAA7134_MAXBOARDS - 1)] = UNSET };
|
|
static unsigned int tuner[] = {[0 ... (SAA7134_MAXBOARDS - 1)] = UNSET };
|
|
static unsigned int card[] = {[0 ... (SAA7134_MAXBOARDS - 1)] = UNSET };
|
|
|
|
|
|
module_param_array(video_nr, int, NULL, 0444);
|
|
module_param_array(vbi_nr, int, NULL, 0444);
|
|
module_param_array(radio_nr, int, NULL, 0444);
|
|
module_param_array(tuner, int, NULL, 0444);
|
|
module_param_array(card, int, NULL, 0444);
|
|
|
|
MODULE_PARM_DESC(video_nr, "video device number");
|
|
MODULE_PARM_DESC(vbi_nr, "vbi device number");
|
|
MODULE_PARM_DESC(radio_nr, "radio device number");
|
|
MODULE_PARM_DESC(tuner, "tuner type");
|
|
MODULE_PARM_DESC(card, "card type");
|
|
|
|
static DEFINE_MUTEX(devlist_lock);
|
|
LIST_HEAD(saa7134_devlist);
|
|
static LIST_HEAD(mops_list);
|
|
static unsigned int saa7134_devcount;
|
|
|
|
int (*saa7134_dmasound_init)(struct saa7134_dev *dev);
|
|
int (*saa7134_dmasound_exit)(struct saa7134_dev *dev);
|
|
|
|
#define dprintk(fmt, arg...) if (core_debug) \
|
|
printk(KERN_DEBUG "%s/core: " fmt, dev->name , ## arg)
|
|
|
|
void saa7134_track_gpio(struct saa7134_dev *dev, char *msg)
|
|
{
|
|
unsigned long mode,status;
|
|
|
|
if (!gpio_tracking)
|
|
return;
|
|
/* rising SAA7134_GPIO_GPRESCAN reads the status */
|
|
saa_andorb(SAA7134_GPIO_GPMODE3,SAA7134_GPIO_GPRESCAN,0);
|
|
saa_andorb(SAA7134_GPIO_GPMODE3,SAA7134_GPIO_GPRESCAN,SAA7134_GPIO_GPRESCAN);
|
|
mode = saa_readl(SAA7134_GPIO_GPMODE0 >> 2) & 0xfffffff;
|
|
status = saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2) & 0xfffffff;
|
|
printk(KERN_DEBUG
|
|
"%s: gpio: mode=0x%07lx in=0x%07lx out=0x%07lx [%s]\n",
|
|
dev->name, mode, (~mode) & status, mode & status, msg);
|
|
}
|
|
|
|
void saa7134_set_gpio(struct saa7134_dev *dev, int bit_no, int value)
|
|
{
|
|
u32 index, bitval;
|
|
|
|
index = 1 << bit_no;
|
|
switch (value) {
|
|
case 0: /* static value */
|
|
case 1: dprintk("setting GPIO%d to static %d\n", bit_no, value);
|
|
/* turn sync mode off if necessary */
|
|
if (index & 0x00c00000)
|
|
saa_andorb(SAA7134_VIDEO_PORT_CTRL6, 0x0f, 0x00);
|
|
if (value)
|
|
bitval = index;
|
|
else
|
|
bitval = 0;
|
|
saa_andorl(SAA7134_GPIO_GPMODE0 >> 2, index, index);
|
|
saa_andorl(SAA7134_GPIO_GPSTATUS0 >> 2, index, bitval);
|
|
break;
|
|
case 3: /* tristate */
|
|
dprintk("setting GPIO%d to tristate\n", bit_no);
|
|
saa_andorl(SAA7134_GPIO_GPMODE0 >> 2, index, 0);
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
|
|
/* ----------------------------------------------------------- */
|
|
/* delayed request_module */
|
|
|
|
#if defined(CONFIG_MODULES) && defined(MODULE)
|
|
|
|
static void request_module_async(struct work_struct *work){
|
|
struct saa7134_dev* dev = container_of(work, struct saa7134_dev, request_module_wk);
|
|
if (card_is_empress(dev))
|
|
request_module("saa7134-empress");
|
|
if (card_is_dvb(dev))
|
|
request_module("saa7134-dvb");
|
|
if (alsa)
|
|
request_module("saa7134-alsa");
|
|
if (oss)
|
|
request_module("saa7134-oss");
|
|
}
|
|
|
|
static void request_submodules(struct saa7134_dev *dev)
|
|
{
|
|
INIT_WORK(&dev->request_module_wk, request_module_async);
|
|
schedule_work(&dev->request_module_wk);
|
|
}
|
|
|
|
#else
|
|
#define request_submodules(dev)
|
|
#endif /* CONFIG_MODULES */
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
/* nr of (saa7134-)pages for the given buffer size */
|
|
static int saa7134_buffer_pages(int size)
|
|
{
|
|
size = PAGE_ALIGN(size);
|
|
size += PAGE_SIZE; /* for non-page-aligned buffers */
|
|
size /= 4096;
|
|
return size;
|
|
}
|
|
|
|
/* calc max # of buffers from size (must not exceed the 4MB virtual
|
|
* address space per DMA channel) */
|
|
int saa7134_buffer_count(unsigned int size, unsigned int count)
|
|
{
|
|
unsigned int maxcount;
|
|
|
|
maxcount = 1024 / saa7134_buffer_pages(size);
|
|
if (count > maxcount)
|
|
count = maxcount;
|
|
return count;
|
|
}
|
|
|
|
int saa7134_buffer_startpage(struct saa7134_buf *buf)
|
|
{
|
|
return saa7134_buffer_pages(buf->vb.bsize) * buf->vb.i;
|
|
}
|
|
|
|
unsigned long saa7134_buffer_base(struct saa7134_buf *buf)
|
|
{
|
|
unsigned long base;
|
|
struct videobuf_dmabuf *dma=videobuf_to_dma(&buf->vb);
|
|
|
|
base = saa7134_buffer_startpage(buf) * 4096;
|
|
base += dma->sglist[0].offset;
|
|
return base;
|
|
}
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
int saa7134_pgtable_alloc(struct pci_dev *pci, struct saa7134_pgtable *pt)
|
|
{
|
|
__le32 *cpu;
|
|
dma_addr_t dma_addr = 0;
|
|
|
|
cpu = pci_alloc_consistent(pci, SAA7134_PGTABLE_SIZE, &dma_addr);
|
|
if (NULL == cpu)
|
|
return -ENOMEM;
|
|
pt->size = SAA7134_PGTABLE_SIZE;
|
|
pt->cpu = cpu;
|
|
pt->dma = dma_addr;
|
|
return 0;
|
|
}
|
|
|
|
int saa7134_pgtable_build(struct pci_dev *pci, struct saa7134_pgtable *pt,
|
|
struct scatterlist *list, unsigned int length,
|
|
unsigned int startpage)
|
|
{
|
|
__le32 *ptr;
|
|
unsigned int i,p;
|
|
|
|
BUG_ON(NULL == pt || NULL == pt->cpu);
|
|
|
|
ptr = pt->cpu + startpage;
|
|
for (i = 0; i < length; i++, list++)
|
|
for (p = 0; p * 4096 < list->length; p++, ptr++)
|
|
*ptr = cpu_to_le32(sg_dma_address(list) - list->offset);
|
|
return 0;
|
|
}
|
|
|
|
void saa7134_pgtable_free(struct pci_dev *pci, struct saa7134_pgtable *pt)
|
|
{
|
|
if (NULL == pt->cpu)
|
|
return;
|
|
pci_free_consistent(pci, pt->size, pt->cpu, pt->dma);
|
|
pt->cpu = NULL;
|
|
}
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
void saa7134_dma_free(struct videobuf_queue *q,struct saa7134_buf *buf)
|
|
{
|
|
struct videobuf_dmabuf *dma=videobuf_to_dma(&buf->vb);
|
|
BUG_ON(in_interrupt());
|
|
|
|
videobuf_waiton(&buf->vb,0,0);
|
|
videobuf_dma_unmap(q, dma);
|
|
videobuf_dma_free(dma);
|
|
buf->vb.state = VIDEOBUF_NEEDS_INIT;
|
|
}
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
int saa7134_buffer_queue(struct saa7134_dev *dev,
|
|
struct saa7134_dmaqueue *q,
|
|
struct saa7134_buf *buf)
|
|
{
|
|
struct saa7134_buf *next = NULL;
|
|
|
|
assert_spin_locked(&dev->slock);
|
|
dprintk("buffer_queue %p\n",buf);
|
|
if (NULL == q->curr) {
|
|
if (!q->need_two) {
|
|
q->curr = buf;
|
|
buf->activate(dev,buf,NULL);
|
|
} else if (list_empty(&q->queue)) {
|
|
list_add_tail(&buf->vb.queue,&q->queue);
|
|
buf->vb.state = VIDEOBUF_QUEUED;
|
|
} else {
|
|
next = list_entry(q->queue.next,struct saa7134_buf,
|
|
vb.queue);
|
|
q->curr = buf;
|
|
buf->activate(dev,buf,next);
|
|
}
|
|
} else {
|
|
list_add_tail(&buf->vb.queue,&q->queue);
|
|
buf->vb.state = VIDEOBUF_QUEUED;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
void saa7134_buffer_finish(struct saa7134_dev *dev,
|
|
struct saa7134_dmaqueue *q,
|
|
unsigned int state)
|
|
{
|
|
assert_spin_locked(&dev->slock);
|
|
dprintk("buffer_finish %p\n",q->curr);
|
|
|
|
/* finish current buffer */
|
|
q->curr->vb.state = state;
|
|
do_gettimeofday(&q->curr->vb.ts);
|
|
wake_up(&q->curr->vb.done);
|
|
q->curr = NULL;
|
|
}
|
|
|
|
void saa7134_buffer_next(struct saa7134_dev *dev,
|
|
struct saa7134_dmaqueue *q)
|
|
{
|
|
struct saa7134_buf *buf,*next = NULL;
|
|
|
|
assert_spin_locked(&dev->slock);
|
|
BUG_ON(NULL != q->curr);
|
|
|
|
if (!list_empty(&q->queue)) {
|
|
/* activate next one from queue */
|
|
buf = list_entry(q->queue.next,struct saa7134_buf,vb.queue);
|
|
dprintk("buffer_next %p [prev=%p/next=%p]\n",
|
|
buf,q->queue.prev,q->queue.next);
|
|
list_del(&buf->vb.queue);
|
|
if (!list_empty(&q->queue))
|
|
next = list_entry(q->queue.next,struct saa7134_buf,
|
|
vb.queue);
|
|
q->curr = buf;
|
|
buf->activate(dev,buf,next);
|
|
dprintk("buffer_next #2 prev=%p/next=%p\n",
|
|
q->queue.prev,q->queue.next);
|
|
} else {
|
|
/* nothing to do -- just stop DMA */
|
|
dprintk("buffer_next %p\n",NULL);
|
|
saa7134_set_dmabits(dev);
|
|
del_timer(&q->timeout);
|
|
}
|
|
}
|
|
|
|
void saa7134_buffer_timeout(unsigned long data)
|
|
{
|
|
struct saa7134_dmaqueue *q = (struct saa7134_dmaqueue*)data;
|
|
struct saa7134_dev *dev = q->dev;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&dev->slock,flags);
|
|
|
|
/* try to reset the hardware (SWRST) */
|
|
saa_writeb(SAA7134_REGION_ENABLE, 0x00);
|
|
saa_writeb(SAA7134_REGION_ENABLE, 0x80);
|
|
saa_writeb(SAA7134_REGION_ENABLE, 0x00);
|
|
|
|
/* flag current buffer as failed,
|
|
try to start over with the next one. */
|
|
if (q->curr) {
|
|
dprintk("timeout on %p\n",q->curr);
|
|
saa7134_buffer_finish(dev,q,VIDEOBUF_ERROR);
|
|
}
|
|
saa7134_buffer_next(dev,q);
|
|
spin_unlock_irqrestore(&dev->slock,flags);
|
|
}
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
int saa7134_set_dmabits(struct saa7134_dev *dev)
|
|
{
|
|
u32 split, task=0, ctrl=0, irq=0;
|
|
enum v4l2_field cap = V4L2_FIELD_ANY;
|
|
enum v4l2_field ov = V4L2_FIELD_ANY;
|
|
|
|
assert_spin_locked(&dev->slock);
|
|
|
|
if (dev->insuspend)
|
|
return 0;
|
|
|
|
/* video capture -- dma 0 + video task A */
|
|
if (dev->video_q.curr) {
|
|
task |= 0x01;
|
|
ctrl |= SAA7134_MAIN_CTRL_TE0;
|
|
irq |= SAA7134_IRQ1_INTE_RA0_1 |
|
|
SAA7134_IRQ1_INTE_RA0_0;
|
|
cap = dev->video_q.curr->vb.field;
|
|
}
|
|
|
|
/* video capture -- dma 1+2 (planar modes) */
|
|
if (dev->video_q.curr &&
|
|
dev->video_q.curr->fmt->planar) {
|
|
ctrl |= SAA7134_MAIN_CTRL_TE4 |
|
|
SAA7134_MAIN_CTRL_TE5;
|
|
}
|
|
|
|
/* screen overlay -- dma 0 + video task B */
|
|
if (dev->ovenable) {
|
|
task |= 0x10;
|
|
ctrl |= SAA7134_MAIN_CTRL_TE1;
|
|
ov = dev->ovfield;
|
|
}
|
|
|
|
/* vbi capture -- dma 0 + vbi task A+B */
|
|
if (dev->vbi_q.curr) {
|
|
task |= 0x22;
|
|
ctrl |= SAA7134_MAIN_CTRL_TE2 |
|
|
SAA7134_MAIN_CTRL_TE3;
|
|
irq |= SAA7134_IRQ1_INTE_RA0_7 |
|
|
SAA7134_IRQ1_INTE_RA0_6 |
|
|
SAA7134_IRQ1_INTE_RA0_5 |
|
|
SAA7134_IRQ1_INTE_RA0_4;
|
|
}
|
|
|
|
/* audio capture -- dma 3 */
|
|
if (dev->dmasound.dma_running) {
|
|
ctrl |= SAA7134_MAIN_CTRL_TE6;
|
|
irq |= SAA7134_IRQ1_INTE_RA3_1 |
|
|
SAA7134_IRQ1_INTE_RA3_0;
|
|
}
|
|
|
|
/* TS capture -- dma 5 */
|
|
if (dev->ts_q.curr) {
|
|
ctrl |= SAA7134_MAIN_CTRL_TE5;
|
|
irq |= SAA7134_IRQ1_INTE_RA2_1 |
|
|
SAA7134_IRQ1_INTE_RA2_0;
|
|
}
|
|
|
|
/* set task conditions + field handling */
|
|
if (V4L2_FIELD_HAS_BOTH(cap) || V4L2_FIELD_HAS_BOTH(ov) || cap == ov) {
|
|
/* default config -- use full frames */
|
|
saa_writeb(SAA7134_TASK_CONDITIONS(TASK_A), 0x0d);
|
|
saa_writeb(SAA7134_TASK_CONDITIONS(TASK_B), 0x0d);
|
|
saa_writeb(SAA7134_FIELD_HANDLING(TASK_A), 0x02);
|
|
saa_writeb(SAA7134_FIELD_HANDLING(TASK_B), 0x02);
|
|
split = 0;
|
|
} else {
|
|
/* split fields between tasks */
|
|
if (V4L2_FIELD_TOP == cap) {
|
|
/* odd A, even B, repeat */
|
|
saa_writeb(SAA7134_TASK_CONDITIONS(TASK_A), 0x0d);
|
|
saa_writeb(SAA7134_TASK_CONDITIONS(TASK_B), 0x0e);
|
|
} else {
|
|
/* odd B, even A, repeat */
|
|
saa_writeb(SAA7134_TASK_CONDITIONS(TASK_A), 0x0e);
|
|
saa_writeb(SAA7134_TASK_CONDITIONS(TASK_B), 0x0d);
|
|
}
|
|
saa_writeb(SAA7134_FIELD_HANDLING(TASK_A), 0x01);
|
|
saa_writeb(SAA7134_FIELD_HANDLING(TASK_B), 0x01);
|
|
split = 1;
|
|
}
|
|
|
|
/* irqs */
|
|
saa_writeb(SAA7134_REGION_ENABLE, task);
|
|
saa_writel(SAA7134_IRQ1, irq);
|
|
saa_andorl(SAA7134_MAIN_CTRL,
|
|
SAA7134_MAIN_CTRL_TE0 |
|
|
SAA7134_MAIN_CTRL_TE1 |
|
|
SAA7134_MAIN_CTRL_TE2 |
|
|
SAA7134_MAIN_CTRL_TE3 |
|
|
SAA7134_MAIN_CTRL_TE4 |
|
|
SAA7134_MAIN_CTRL_TE5 |
|
|
SAA7134_MAIN_CTRL_TE6,
|
|
ctrl);
|
|
dprintk("dmabits: task=0x%02x ctrl=0x%02x irq=0x%x split=%s\n",
|
|
task, ctrl, irq, split ? "no" : "yes");
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
/* IRQ handler + helpers */
|
|
|
|
static char *irqbits[] = {
|
|
"DONE_RA0", "DONE_RA1", "DONE_RA2", "DONE_RA3",
|
|
"AR", "PE", "PWR_ON", "RDCAP", "INTL", "FIDT", "MMC",
|
|
"TRIG_ERR", "CONF_ERR", "LOAD_ERR",
|
|
"GPIO16?", "GPIO18", "GPIO22", "GPIO23"
|
|
};
|
|
#define IRQBITS ARRAY_SIZE(irqbits)
|
|
|
|
static void print_irqstatus(struct saa7134_dev *dev, int loop,
|
|
unsigned long report, unsigned long status)
|
|
{
|
|
unsigned int i;
|
|
|
|
printk(KERN_DEBUG "%s/irq[%d,%ld]: r=0x%lx s=0x%02lx",
|
|
dev->name,loop,jiffies,report,status);
|
|
for (i = 0; i < IRQBITS; i++) {
|
|
if (!(report & (1 << i)))
|
|
continue;
|
|
printk(" %s",irqbits[i]);
|
|
}
|
|
if (report & SAA7134_IRQ_REPORT_DONE_RA0) {
|
|
printk(" | RA0=%s,%s,%s,%ld",
|
|
(status & 0x40) ? "vbi" : "video",
|
|
(status & 0x20) ? "b" : "a",
|
|
(status & 0x10) ? "odd" : "even",
|
|
(status & 0x0f));
|
|
}
|
|
printk("\n");
|
|
}
|
|
|
|
static irqreturn_t saa7134_irq(int irq, void *dev_id)
|
|
{
|
|
struct saa7134_dev *dev = (struct saa7134_dev*) dev_id;
|
|
unsigned long report,status;
|
|
int loop, handled = 0;
|
|
|
|
if (dev->insuspend)
|
|
goto out;
|
|
|
|
for (loop = 0; loop < 10; loop++) {
|
|
report = saa_readl(SAA7134_IRQ_REPORT);
|
|
status = saa_readl(SAA7134_IRQ_STATUS);
|
|
|
|
/* If dmasound support is active and we get a sound report,
|
|
* mask out the report and let the saa7134-alsa module deal
|
|
* with it */
|
|
if ((report & SAA7134_IRQ_REPORT_DONE_RA3) &&
|
|
(dev->dmasound.priv_data != NULL) )
|
|
{
|
|
if (irq_debug > 1)
|
|
printk(KERN_DEBUG "%s/irq: preserving DMA sound interrupt\n",
|
|
dev->name);
|
|
report &= ~SAA7134_IRQ_REPORT_DONE_RA3;
|
|
}
|
|
|
|
if (0 == report) {
|
|
if (irq_debug > 1)
|
|
printk(KERN_DEBUG "%s/irq: no (more) work\n",
|
|
dev->name);
|
|
goto out;
|
|
}
|
|
|
|
handled = 1;
|
|
saa_writel(SAA7134_IRQ_REPORT,report);
|
|
if (irq_debug)
|
|
print_irqstatus(dev,loop,report,status);
|
|
|
|
|
|
if ((report & SAA7134_IRQ_REPORT_RDCAP) ||
|
|
(report & SAA7134_IRQ_REPORT_INTL))
|
|
saa7134_irq_video_signalchange(dev);
|
|
|
|
|
|
if ((report & SAA7134_IRQ_REPORT_DONE_RA0) &&
|
|
(status & 0x60) == 0)
|
|
saa7134_irq_video_done(dev,status);
|
|
|
|
if ((report & SAA7134_IRQ_REPORT_DONE_RA0) &&
|
|
(status & 0x40) == 0x40)
|
|
saa7134_irq_vbi_done(dev,status);
|
|
|
|
if ((report & SAA7134_IRQ_REPORT_DONE_RA2) &&
|
|
card_has_mpeg(dev))
|
|
saa7134_irq_ts_done(dev,status);
|
|
|
|
if (report & SAA7134_IRQ_REPORT_GPIO16) {
|
|
switch (dev->has_remote) {
|
|
case SAA7134_REMOTE_GPIO:
|
|
if (!dev->remote)
|
|
break;
|
|
if (dev->remote->mask_keydown & 0x10000) {
|
|
saa7134_input_irq(dev);
|
|
}
|
|
break;
|
|
|
|
case SAA7134_REMOTE_I2C:
|
|
break; /* FIXME: invoke I2C get_key() */
|
|
|
|
default: /* GPIO16 not used by IR remote */
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (report & SAA7134_IRQ_REPORT_GPIO18) {
|
|
switch (dev->has_remote) {
|
|
case SAA7134_REMOTE_GPIO:
|
|
if (!dev->remote)
|
|
break;
|
|
if ((dev->remote->mask_keydown & 0x40000) ||
|
|
(dev->remote->mask_keyup & 0x40000)) {
|
|
saa7134_input_irq(dev);
|
|
}
|
|
break;
|
|
|
|
case SAA7134_REMOTE_I2C:
|
|
break; /* FIXME: invoke I2C get_key() */
|
|
|
|
default: /* GPIO18 not used by IR remote */
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
if (10 == loop) {
|
|
print_irqstatus(dev,loop,report,status);
|
|
if (report & SAA7134_IRQ_REPORT_PE) {
|
|
/* disable all parity error */
|
|
printk(KERN_WARNING "%s/irq: looping -- "
|
|
"clearing PE (parity error!) enable bit\n",dev->name);
|
|
saa_clearl(SAA7134_IRQ2,SAA7134_IRQ2_INTE_PE);
|
|
} else if (report & SAA7134_IRQ_REPORT_GPIO16) {
|
|
/* disable gpio16 IRQ */
|
|
printk(KERN_WARNING "%s/irq: looping -- "
|
|
"clearing GPIO16 enable bit\n",dev->name);
|
|
saa_clearl(SAA7134_IRQ2, SAA7134_IRQ2_INTE_GPIO16);
|
|
} else if (report & SAA7134_IRQ_REPORT_GPIO18) {
|
|
/* disable gpio18 IRQs */
|
|
printk(KERN_WARNING "%s/irq: looping -- "
|
|
"clearing GPIO18 enable bit\n",dev->name);
|
|
saa_clearl(SAA7134_IRQ2, SAA7134_IRQ2_INTE_GPIO18);
|
|
} else {
|
|
/* disable all irqs */
|
|
printk(KERN_WARNING "%s/irq: looping -- "
|
|
"clearing all enable bits\n",dev->name);
|
|
saa_writel(SAA7134_IRQ1,0);
|
|
saa_writel(SAA7134_IRQ2,0);
|
|
}
|
|
}
|
|
|
|
out:
|
|
return IRQ_RETVAL(handled);
|
|
}
|
|
|
|
/* ------------------------------------------------------------------ */
|
|
|
|
/* early init (no i2c, no irq) */
|
|
|
|
static int saa7134_hw_enable1(struct saa7134_dev *dev)
|
|
{
|
|
/* RAM FIFO config */
|
|
saa_writel(SAA7134_FIFO_SIZE, 0x08070503);
|
|
saa_writel(SAA7134_THRESHOULD, 0x02020202);
|
|
|
|
/* enable audio + video processing */
|
|
saa_writel(SAA7134_MAIN_CTRL,
|
|
SAA7134_MAIN_CTRL_VPLLE |
|
|
SAA7134_MAIN_CTRL_APLLE |
|
|
SAA7134_MAIN_CTRL_EXOSC |
|
|
SAA7134_MAIN_CTRL_EVFE1 |
|
|
SAA7134_MAIN_CTRL_EVFE2 |
|
|
SAA7134_MAIN_CTRL_ESFE |
|
|
SAA7134_MAIN_CTRL_EBDAC);
|
|
|
|
/*
|
|
* Initialize OSS _after_ enabling audio clock PLL and audio processing.
|
|
* OSS initialization writes to registers via the audio DSP; these
|
|
* writes will fail unless the audio clock has been started. At worst,
|
|
* audio will not work.
|
|
*/
|
|
|
|
/* enable peripheral devices */
|
|
saa_writeb(SAA7134_SPECIAL_MODE, 0x01);
|
|
|
|
/* set vertical line numbering start (vbi needs this) */
|
|
saa_writeb(SAA7134_SOURCE_TIMING2, 0x20);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int saa7134_hwinit1(struct saa7134_dev *dev)
|
|
{
|
|
dprintk("hwinit1\n");
|
|
|
|
saa_writel(SAA7134_IRQ1, 0);
|
|
saa_writel(SAA7134_IRQ2, 0);
|
|
mutex_init(&dev->lock);
|
|
spin_lock_init(&dev->slock);
|
|
|
|
saa7134_track_gpio(dev,"pre-init");
|
|
saa7134_video_init1(dev);
|
|
saa7134_vbi_init1(dev);
|
|
if (card_has_mpeg(dev))
|
|
saa7134_ts_init1(dev);
|
|
saa7134_input_init1(dev);
|
|
|
|
saa7134_hw_enable1(dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* late init (with i2c + irq) */
|
|
static int saa7134_hw_enable2(struct saa7134_dev *dev)
|
|
{
|
|
|
|
unsigned int irq2_mask;
|
|
|
|
/* enable IRQ's */
|
|
irq2_mask =
|
|
SAA7134_IRQ2_INTE_DEC3 |
|
|
SAA7134_IRQ2_INTE_DEC2 |
|
|
SAA7134_IRQ2_INTE_DEC1 |
|
|
SAA7134_IRQ2_INTE_DEC0 |
|
|
SAA7134_IRQ2_INTE_PE |
|
|
SAA7134_IRQ2_INTE_AR;
|
|
|
|
if (dev->has_remote == SAA7134_REMOTE_GPIO && dev->remote) {
|
|
if (dev->remote->mask_keydown & 0x10000)
|
|
irq2_mask |= SAA7134_IRQ2_INTE_GPIO16;
|
|
else if (dev->remote->mask_keydown & 0x40000)
|
|
irq2_mask |= SAA7134_IRQ2_INTE_GPIO18;
|
|
else if (dev->remote->mask_keyup & 0x40000)
|
|
irq2_mask |= SAA7134_IRQ2_INTE_GPIO18A;
|
|
}
|
|
|
|
if (dev->has_remote == SAA7134_REMOTE_I2C) {
|
|
request_module("ir-kbd-i2c");
|
|
}
|
|
|
|
saa_writel(SAA7134_IRQ1, 0);
|
|
saa_writel(SAA7134_IRQ2, irq2_mask);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int saa7134_hwinit2(struct saa7134_dev *dev)
|
|
{
|
|
|
|
dprintk("hwinit2\n");
|
|
|
|
saa7134_video_init2(dev);
|
|
saa7134_tvaudio_init2(dev);
|
|
|
|
saa7134_hw_enable2(dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
/* shutdown */
|
|
static int saa7134_hwfini(struct saa7134_dev *dev)
|
|
{
|
|
dprintk("hwfini\n");
|
|
|
|
if (card_has_mpeg(dev))
|
|
saa7134_ts_fini(dev);
|
|
saa7134_input_fini(dev);
|
|
saa7134_vbi_fini(dev);
|
|
saa7134_tvaudio_fini(dev);
|
|
return 0;
|
|
}
|
|
|
|
static void __devinit must_configure_manually(void)
|
|
{
|
|
unsigned int i,p;
|
|
|
|
printk(KERN_WARNING
|
|
"saa7134: <rant>\n"
|
|
"saa7134: Congratulations! Your TV card vendor saved a few\n"
|
|
"saa7134: cents for a eeprom, thus your pci board has no\n"
|
|
"saa7134: subsystem ID and I can't identify it automatically\n"
|
|
"saa7134: </rant>\n"
|
|
"saa7134: I feel better now. Ok, here are the good news:\n"
|
|
"saa7134: You can use the card=<nr> insmod option to specify\n"
|
|
"saa7134: which board do you have. The list:\n");
|
|
for (i = 0; i < saa7134_bcount; i++) {
|
|
printk(KERN_WARNING "saa7134: card=%d -> %-40.40s",
|
|
i,saa7134_boards[i].name);
|
|
for (p = 0; saa7134_pci_tbl[p].driver_data; p++) {
|
|
if (saa7134_pci_tbl[p].driver_data != i)
|
|
continue;
|
|
printk(" %04x:%04x",
|
|
saa7134_pci_tbl[p].subvendor,
|
|
saa7134_pci_tbl[p].subdevice);
|
|
}
|
|
printk("\n");
|
|
}
|
|
}
|
|
|
|
static struct video_device *vdev_init(struct saa7134_dev *dev,
|
|
struct video_device *template,
|
|
char *type)
|
|
{
|
|
struct video_device *vfd;
|
|
|
|
vfd = video_device_alloc();
|
|
if (NULL == vfd)
|
|
return NULL;
|
|
*vfd = *template;
|
|
vfd->minor = -1;
|
|
vfd->parent = &dev->pci->dev;
|
|
vfd->release = video_device_release;
|
|
vfd->debug = video_debug;
|
|
snprintf(vfd->name, sizeof(vfd->name), "%s %s (%s)",
|
|
dev->name, type, saa7134_boards[dev->board].name);
|
|
return vfd;
|
|
}
|
|
|
|
static void saa7134_unregister_video(struct saa7134_dev *dev)
|
|
{
|
|
if (dev->video_dev) {
|
|
if (-1 != dev->video_dev->minor)
|
|
video_unregister_device(dev->video_dev);
|
|
else
|
|
video_device_release(dev->video_dev);
|
|
dev->video_dev = NULL;
|
|
}
|
|
if (dev->vbi_dev) {
|
|
if (-1 != dev->vbi_dev->minor)
|
|
video_unregister_device(dev->vbi_dev);
|
|
else
|
|
video_device_release(dev->vbi_dev);
|
|
dev->vbi_dev = NULL;
|
|
}
|
|
if (dev->radio_dev) {
|
|
if (-1 != dev->radio_dev->minor)
|
|
video_unregister_device(dev->radio_dev);
|
|
else
|
|
video_device_release(dev->radio_dev);
|
|
dev->radio_dev = NULL;
|
|
}
|
|
}
|
|
|
|
static void mpeg_ops_attach(struct saa7134_mpeg_ops *ops,
|
|
struct saa7134_dev *dev)
|
|
{
|
|
int err;
|
|
|
|
if (NULL != dev->mops)
|
|
return;
|
|
if (saa7134_boards[dev->board].mpeg != ops->type)
|
|
return;
|
|
err = ops->init(dev);
|
|
if (0 != err)
|
|
return;
|
|
dev->mops = ops;
|
|
}
|
|
|
|
static void mpeg_ops_detach(struct saa7134_mpeg_ops *ops,
|
|
struct saa7134_dev *dev)
|
|
{
|
|
if (NULL == dev->mops)
|
|
return;
|
|
if (dev->mops != ops)
|
|
return;
|
|
dev->mops->fini(dev);
|
|
dev->mops = NULL;
|
|
}
|
|
|
|
static int __devinit saa7134_initdev(struct pci_dev *pci_dev,
|
|
const struct pci_device_id *pci_id)
|
|
{
|
|
struct saa7134_dev *dev;
|
|
struct saa7134_mpeg_ops *mops;
|
|
int err;
|
|
|
|
if (saa7134_devcount == SAA7134_MAXBOARDS)
|
|
return -ENOMEM;
|
|
|
|
dev = kzalloc(sizeof(*dev),GFP_KERNEL);
|
|
if (NULL == dev)
|
|
return -ENOMEM;
|
|
|
|
/* pci init */
|
|
dev->pci = pci_dev;
|
|
if (pci_enable_device(pci_dev)) {
|
|
err = -EIO;
|
|
goto fail1;
|
|
}
|
|
|
|
dev->nr = saa7134_devcount;
|
|
sprintf(dev->name,"saa%x[%d]",pci_dev->device,dev->nr);
|
|
|
|
/* pci quirks */
|
|
if (pci_pci_problems) {
|
|
if (pci_pci_problems & PCIPCI_TRITON)
|
|
printk(KERN_INFO "%s: quirk: PCIPCI_TRITON\n", dev->name);
|
|
if (pci_pci_problems & PCIPCI_NATOMA)
|
|
printk(KERN_INFO "%s: quirk: PCIPCI_NATOMA\n", dev->name);
|
|
if (pci_pci_problems & PCIPCI_VIAETBF)
|
|
printk(KERN_INFO "%s: quirk: PCIPCI_VIAETBF\n", dev->name);
|
|
if (pci_pci_problems & PCIPCI_VSFX)
|
|
printk(KERN_INFO "%s: quirk: PCIPCI_VSFX\n",dev->name);
|
|
#ifdef PCIPCI_ALIMAGIK
|
|
if (pci_pci_problems & PCIPCI_ALIMAGIK) {
|
|
printk(KERN_INFO "%s: quirk: PCIPCI_ALIMAGIK -- latency fixup\n",
|
|
dev->name);
|
|
latency = 0x0A;
|
|
}
|
|
#endif
|
|
if (pci_pci_problems & (PCIPCI_FAIL|PCIAGP_FAIL)) {
|
|
printk(KERN_INFO "%s: quirk: this driver and your "
|
|
"chipset may not work together"
|
|
" in overlay mode.\n",dev->name);
|
|
if (!saa7134_no_overlay) {
|
|
printk(KERN_INFO "%s: quirk: overlay "
|
|
"mode will be disabled.\n",
|
|
dev->name);
|
|
saa7134_no_overlay = 1;
|
|
} else {
|
|
printk(KERN_INFO "%s: quirk: overlay "
|
|
"mode will be forced. Use this"
|
|
" option at your own risk.\n",
|
|
dev->name);
|
|
}
|
|
}
|
|
}
|
|
if (UNSET != latency) {
|
|
printk(KERN_INFO "%s: setting pci latency timer to %d\n",
|
|
dev->name,latency);
|
|
pci_write_config_byte(pci_dev, PCI_LATENCY_TIMER, latency);
|
|
}
|
|
|
|
/* print pci info */
|
|
pci_read_config_byte(pci_dev, PCI_CLASS_REVISION, &dev->pci_rev);
|
|
pci_read_config_byte(pci_dev, PCI_LATENCY_TIMER, &dev->pci_lat);
|
|
printk(KERN_INFO "%s: found at %s, rev: %d, irq: %d, "
|
|
"latency: %d, mmio: 0x%llx\n", dev->name,
|
|
pci_name(pci_dev), dev->pci_rev, pci_dev->irq,
|
|
dev->pci_lat,(unsigned long long)pci_resource_start(pci_dev,0));
|
|
pci_set_master(pci_dev);
|
|
if (!pci_dma_supported(pci_dev, DMA_32BIT_MASK)) {
|
|
printk("%s: Oops: no 32bit PCI DMA ???\n",dev->name);
|
|
err = -EIO;
|
|
goto fail1;
|
|
}
|
|
|
|
/* board config */
|
|
dev->board = pci_id->driver_data;
|
|
if (card[dev->nr] >= 0 &&
|
|
card[dev->nr] < saa7134_bcount)
|
|
dev->board = card[dev->nr];
|
|
if (SAA7134_BOARD_NOAUTO == dev->board) {
|
|
must_configure_manually();
|
|
dev->board = SAA7134_BOARD_UNKNOWN;
|
|
}
|
|
dev->autodetected = card[dev->nr] != dev->board;
|
|
dev->tuner_type = saa7134_boards[dev->board].tuner_type;
|
|
dev->tuner_addr = saa7134_boards[dev->board].tuner_addr;
|
|
dev->tda9887_conf = saa7134_boards[dev->board].tda9887_conf;
|
|
if (UNSET != tuner[dev->nr])
|
|
dev->tuner_type = tuner[dev->nr];
|
|
printk(KERN_INFO "%s: subsystem: %04x:%04x, board: %s [card=%d,%s]\n",
|
|
dev->name,pci_dev->subsystem_vendor,
|
|
pci_dev->subsystem_device,saa7134_boards[dev->board].name,
|
|
dev->board, dev->autodetected ?
|
|
"autodetected" : "insmod option");
|
|
|
|
/* get mmio */
|
|
if (!request_mem_region(pci_resource_start(pci_dev,0),
|
|
pci_resource_len(pci_dev,0),
|
|
dev->name)) {
|
|
err = -EBUSY;
|
|
printk(KERN_ERR "%s: can't get MMIO memory @ 0x%llx\n",
|
|
dev->name,(unsigned long long)pci_resource_start(pci_dev,0));
|
|
goto fail1;
|
|
}
|
|
dev->lmmio = ioremap(pci_resource_start(pci_dev, 0),
|
|
pci_resource_len(pci_dev, 0));
|
|
dev->bmmio = (__u8 __iomem *)dev->lmmio;
|
|
if (NULL == dev->lmmio) {
|
|
err = -EIO;
|
|
printk(KERN_ERR "%s: can't ioremap() MMIO memory\n",
|
|
dev->name);
|
|
goto fail2;
|
|
}
|
|
|
|
/* initialize hardware #1 */
|
|
saa7134_board_init1(dev);
|
|
saa7134_hwinit1(dev);
|
|
|
|
/* get irq */
|
|
err = request_irq(pci_dev->irq, saa7134_irq,
|
|
IRQF_SHARED | IRQF_DISABLED, dev->name, dev);
|
|
if (err < 0) {
|
|
printk(KERN_ERR "%s: can't get IRQ %d\n",
|
|
dev->name,pci_dev->irq);
|
|
goto fail3;
|
|
}
|
|
|
|
/* wait a bit, register i2c bus */
|
|
msleep(100);
|
|
saa7134_i2c_register(dev);
|
|
|
|
/* initialize hardware #2 */
|
|
if (TUNER_ABSENT != dev->tuner_type)
|
|
request_module("tuner");
|
|
saa7134_board_init2(dev);
|
|
|
|
saa7134_hwinit2(dev);
|
|
|
|
/* load i2c helpers */
|
|
if (card_is_empress(dev)) {
|
|
request_module("saa6752hs");
|
|
}
|
|
|
|
request_submodules(dev);
|
|
|
|
v4l2_prio_init(&dev->prio);
|
|
|
|
/* register v4l devices */
|
|
if (saa7134_no_overlay > 0)
|
|
printk(KERN_INFO "%s: Overlay support disabled.\n", dev->name);
|
|
|
|
dev->video_dev = vdev_init(dev,&saa7134_video_template,"video");
|
|
err = video_register_device(dev->video_dev,VFL_TYPE_GRABBER,
|
|
video_nr[dev->nr]);
|
|
if (err < 0) {
|
|
printk(KERN_INFO "%s: can't register video device\n",
|
|
dev->name);
|
|
goto fail4;
|
|
}
|
|
printk(KERN_INFO "%s: registered device video%d [v4l2]\n",
|
|
dev->name, dev->video_dev->num);
|
|
|
|
dev->vbi_dev = vdev_init(dev, &saa7134_video_template, "vbi");
|
|
|
|
err = video_register_device(dev->vbi_dev,VFL_TYPE_VBI,
|
|
vbi_nr[dev->nr]);
|
|
if (err < 0)
|
|
goto fail4;
|
|
printk(KERN_INFO "%s: registered device vbi%d\n",
|
|
dev->name, dev->vbi_dev->num);
|
|
|
|
if (card_has_radio(dev)) {
|
|
dev->radio_dev = vdev_init(dev,&saa7134_radio_template,"radio");
|
|
err = video_register_device(dev->radio_dev,VFL_TYPE_RADIO,
|
|
radio_nr[dev->nr]);
|
|
if (err < 0)
|
|
goto fail4;
|
|
printk(KERN_INFO "%s: registered device radio%d\n",
|
|
dev->name, dev->radio_dev->num);
|
|
}
|
|
|
|
/* everything worked */
|
|
pci_set_drvdata(pci_dev,dev);
|
|
saa7134_devcount++;
|
|
|
|
mutex_lock(&devlist_lock);
|
|
list_for_each_entry(mops, &mops_list, next)
|
|
mpeg_ops_attach(mops, dev);
|
|
list_add_tail(&dev->devlist,&saa7134_devlist);
|
|
mutex_unlock(&devlist_lock);
|
|
|
|
/* check for signal */
|
|
saa7134_irq_video_signalchange(dev);
|
|
|
|
if (saa7134_dmasound_init && !dev->dmasound.priv_data) {
|
|
saa7134_dmasound_init(dev);
|
|
}
|
|
|
|
if (TUNER_ABSENT != dev->tuner_type)
|
|
saa7134_i2c_call_clients(dev, TUNER_SET_STANDBY, NULL);
|
|
|
|
return 0;
|
|
|
|
fail4:
|
|
saa7134_unregister_video(dev);
|
|
saa7134_i2c_unregister(dev);
|
|
free_irq(pci_dev->irq, dev);
|
|
fail3:
|
|
saa7134_hwfini(dev);
|
|
iounmap(dev->lmmio);
|
|
fail2:
|
|
release_mem_region(pci_resource_start(pci_dev,0),
|
|
pci_resource_len(pci_dev,0));
|
|
fail1:
|
|
kfree(dev);
|
|
return err;
|
|
}
|
|
|
|
static void __devexit saa7134_finidev(struct pci_dev *pci_dev)
|
|
{
|
|
struct saa7134_dev *dev = pci_get_drvdata(pci_dev);
|
|
struct saa7134_mpeg_ops *mops;
|
|
|
|
/* Release DMA sound modules if present */
|
|
if (saa7134_dmasound_exit && dev->dmasound.priv_data) {
|
|
saa7134_dmasound_exit(dev);
|
|
}
|
|
|
|
/* debugging ... */
|
|
if (irq_debug) {
|
|
u32 report = saa_readl(SAA7134_IRQ_REPORT);
|
|
u32 status = saa_readl(SAA7134_IRQ_STATUS);
|
|
print_irqstatus(dev,42,report,status);
|
|
}
|
|
|
|
/* disable peripheral devices */
|
|
saa_writeb(SAA7134_SPECIAL_MODE,0);
|
|
|
|
/* shutdown hardware */
|
|
saa_writel(SAA7134_IRQ1,0);
|
|
saa_writel(SAA7134_IRQ2,0);
|
|
saa_writel(SAA7134_MAIN_CTRL,0);
|
|
|
|
/* shutdown subsystems */
|
|
saa7134_hwfini(dev);
|
|
|
|
/* unregister */
|
|
mutex_lock(&devlist_lock);
|
|
list_del(&dev->devlist);
|
|
list_for_each_entry(mops, &mops_list, next)
|
|
mpeg_ops_detach(mops, dev);
|
|
mutex_unlock(&devlist_lock);
|
|
saa7134_devcount--;
|
|
|
|
saa7134_i2c_unregister(dev);
|
|
saa7134_unregister_video(dev);
|
|
|
|
|
|
/* the DMA sound modules should be unloaded before reaching
|
|
this, but just in case they are still present... */
|
|
if (dev->dmasound.priv_data != NULL) {
|
|
free_irq(pci_dev->irq, &dev->dmasound);
|
|
dev->dmasound.priv_data = NULL;
|
|
}
|
|
|
|
|
|
/* release resources */
|
|
free_irq(pci_dev->irq, dev);
|
|
iounmap(dev->lmmio);
|
|
release_mem_region(pci_resource_start(pci_dev,0),
|
|
pci_resource_len(pci_dev,0));
|
|
|
|
pci_set_drvdata(pci_dev, NULL);
|
|
|
|
/* free memory */
|
|
kfree(dev);
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
|
|
/* resends a current buffer in queue after resume */
|
|
static int saa7134_buffer_requeue(struct saa7134_dev *dev,
|
|
struct saa7134_dmaqueue *q)
|
|
{
|
|
struct saa7134_buf *buf, *next;
|
|
|
|
assert_spin_locked(&dev->slock);
|
|
|
|
buf = q->curr;
|
|
next = buf;
|
|
dprintk("buffer_requeue\n");
|
|
|
|
if (!buf)
|
|
return 0;
|
|
|
|
dprintk("buffer_requeue : resending active buffers \n");
|
|
|
|
if (!list_empty(&q->queue))
|
|
next = list_entry(q->queue.next, struct saa7134_buf,
|
|
vb.queue);
|
|
buf->activate(dev, buf, next);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int saa7134_suspend(struct pci_dev *pci_dev , pm_message_t state)
|
|
{
|
|
|
|
struct saa7134_dev *dev = pci_get_drvdata(pci_dev);
|
|
|
|
/* disable overlay - apps should enable it explicitly on resume*/
|
|
dev->ovenable = 0;
|
|
|
|
/* Disable interrupts, DMA, and rest of the chip*/
|
|
saa_writel(SAA7134_IRQ1, 0);
|
|
saa_writel(SAA7134_IRQ2, 0);
|
|
saa_writel(SAA7134_MAIN_CTRL, 0);
|
|
|
|
dev->insuspend = 1;
|
|
synchronize_irq(pci_dev->irq);
|
|
|
|
/* ACK interrupts once more, just in case,
|
|
since the IRQ handler won't ack them anymore*/
|
|
|
|
saa_writel(SAA7134_IRQ_REPORT, saa_readl(SAA7134_IRQ_REPORT));
|
|
|
|
/* Disable timeout timers - if we have active buffers, we will
|
|
fill them on resume*/
|
|
|
|
del_timer(&dev->video_q.timeout);
|
|
del_timer(&dev->vbi_q.timeout);
|
|
del_timer(&dev->ts_q.timeout);
|
|
|
|
if (dev->remote)
|
|
saa7134_ir_stop(dev);
|
|
|
|
pci_save_state(pci_dev);
|
|
pci_set_power_state(pci_dev, pci_choose_state(pci_dev, state));
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int saa7134_resume(struct pci_dev *pci_dev)
|
|
{
|
|
struct saa7134_dev *dev = pci_get_drvdata(pci_dev);
|
|
unsigned long flags;
|
|
|
|
pci_set_power_state(pci_dev, PCI_D0);
|
|
pci_restore_state(pci_dev);
|
|
|
|
/* Do things that are done in saa7134_initdev ,
|
|
except of initializing memory structures.*/
|
|
|
|
saa7134_board_init1(dev);
|
|
|
|
/* saa7134_hwinit1 */
|
|
if (saa7134_boards[dev->board].video_out)
|
|
saa7134_videoport_init(dev);
|
|
if (card_has_mpeg(dev))
|
|
saa7134_ts_init_hw(dev);
|
|
if (dev->remote)
|
|
saa7134_ir_start(dev, dev->remote);
|
|
saa7134_hw_enable1(dev);
|
|
|
|
msleep(100);
|
|
|
|
saa7134_board_init2(dev);
|
|
|
|
/*saa7134_hwinit2*/
|
|
saa7134_set_tvnorm_hw(dev);
|
|
saa7134_tvaudio_setmute(dev);
|
|
saa7134_tvaudio_setvolume(dev, dev->ctl_volume);
|
|
saa7134_tvaudio_init(dev);
|
|
saa7134_tvaudio_do_scan(dev);
|
|
saa7134_enable_i2s(dev);
|
|
saa7134_hw_enable2(dev);
|
|
|
|
saa7134_irq_video_signalchange(dev);
|
|
|
|
/*resume unfinished buffer(s)*/
|
|
spin_lock_irqsave(&dev->slock, flags);
|
|
saa7134_buffer_requeue(dev, &dev->video_q);
|
|
saa7134_buffer_requeue(dev, &dev->vbi_q);
|
|
saa7134_buffer_requeue(dev, &dev->ts_q);
|
|
|
|
/* FIXME: Disable DMA audio sound - temporary till proper support
|
|
is implemented*/
|
|
|
|
dev->dmasound.dma_running = 0;
|
|
|
|
/* start DMA now*/
|
|
dev->insuspend = 0;
|
|
smp_wmb();
|
|
saa7134_set_dmabits(dev);
|
|
spin_unlock_irqrestore(&dev->slock, flags);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
/* ----------------------------------------------------------- */
|
|
|
|
int saa7134_ts_register(struct saa7134_mpeg_ops *ops)
|
|
{
|
|
struct saa7134_dev *dev;
|
|
|
|
mutex_lock(&devlist_lock);
|
|
list_for_each_entry(dev, &saa7134_devlist, devlist)
|
|
mpeg_ops_attach(ops, dev);
|
|
list_add_tail(&ops->next,&mops_list);
|
|
mutex_unlock(&devlist_lock);
|
|
return 0;
|
|
}
|
|
|
|
void saa7134_ts_unregister(struct saa7134_mpeg_ops *ops)
|
|
{
|
|
struct saa7134_dev *dev;
|
|
|
|
mutex_lock(&devlist_lock);
|
|
list_del(&ops->next);
|
|
list_for_each_entry(dev, &saa7134_devlist, devlist)
|
|
mpeg_ops_detach(ops, dev);
|
|
mutex_unlock(&devlist_lock);
|
|
}
|
|
|
|
EXPORT_SYMBOL(saa7134_ts_register);
|
|
EXPORT_SYMBOL(saa7134_ts_unregister);
|
|
|
|
/* ----------------------------------------------------------- */
|
|
|
|
static struct pci_driver saa7134_pci_driver = {
|
|
.name = "saa7134",
|
|
.id_table = saa7134_pci_tbl,
|
|
.probe = saa7134_initdev,
|
|
.remove = __devexit_p(saa7134_finidev),
|
|
#ifdef CONFIG_PM
|
|
.suspend = saa7134_suspend,
|
|
.resume = saa7134_resume
|
|
#endif
|
|
};
|
|
|
|
static int saa7134_init(void)
|
|
{
|
|
INIT_LIST_HEAD(&saa7134_devlist);
|
|
printk(KERN_INFO "saa7130/34: v4l2 driver version %d.%d.%d loaded\n",
|
|
(SAA7134_VERSION_CODE >> 16) & 0xff,
|
|
(SAA7134_VERSION_CODE >> 8) & 0xff,
|
|
SAA7134_VERSION_CODE & 0xff);
|
|
#ifdef SNAPSHOT
|
|
printk(KERN_INFO "saa7130/34: snapshot date %04d-%02d-%02d\n",
|
|
SNAPSHOT/10000, (SNAPSHOT/100)%100, SNAPSHOT%100);
|
|
#endif
|
|
return pci_register_driver(&saa7134_pci_driver);
|
|
}
|
|
|
|
static void saa7134_fini(void)
|
|
{
|
|
pci_unregister_driver(&saa7134_pci_driver);
|
|
}
|
|
|
|
module_init(saa7134_init);
|
|
module_exit(saa7134_fini);
|
|
|
|
/* ----------------------------------------------------------- */
|
|
|
|
EXPORT_SYMBOL(saa7134_set_gpio);
|
|
EXPORT_SYMBOL(saa7134_i2c_call_clients);
|
|
EXPORT_SYMBOL(saa7134_devlist);
|
|
EXPORT_SYMBOL(saa7134_boards);
|
|
|
|
/* ----------------- for the DMA sound modules --------------- */
|
|
|
|
EXPORT_SYMBOL(saa7134_dmasound_init);
|
|
EXPORT_SYMBOL(saa7134_dmasound_exit);
|
|
EXPORT_SYMBOL(saa7134_pgtable_free);
|
|
EXPORT_SYMBOL(saa7134_pgtable_build);
|
|
EXPORT_SYMBOL(saa7134_pgtable_alloc);
|
|
EXPORT_SYMBOL(saa7134_set_dmabits);
|
|
|
|
/* ----------------------------------------------------------- */
|
|
/*
|
|
* Local variables:
|
|
* c-basic-offset: 8
|
|
* End:
|
|
*/
|