mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-27 06:04:23 +08:00
37c646dc51
The Lantiq PEF2256 is a framer and line interface component designed to fulfill all required interfacing between an analog E1/T1/J1 line and the digital PCM system highway/H.100 bus. This kind of component can be found in old telecommunication system. It was used to digital transmission of many simultaneous telephone calls by time-division multiplexing. Also using HDLC protocol, WAN networks can be reached through the framer. This pinmux support handles the pin muxing part (pins RP(A..D) and pins XP(A..D)) of the PEF2256. Signed-off-by: Herve Codina <herve.codina@bootlin.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20231128132534.258459-5-herve.codina@bootlin.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
554 lines
15 KiB
Plaintext
554 lines
15 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# PINCTRL infrastructure and drivers
|
|
#
|
|
|
|
menuconfig PINCTRL
|
|
bool "Pin controllers"
|
|
|
|
if PINCTRL
|
|
|
|
config GENERIC_PINCTRL_GROUPS
|
|
bool
|
|
|
|
config PINMUX
|
|
bool "Support pin multiplexing controllers" if COMPILE_TEST
|
|
|
|
config GENERIC_PINMUX_FUNCTIONS
|
|
bool
|
|
select PINMUX
|
|
|
|
config PINCONF
|
|
bool "Support pin configuration controllers" if COMPILE_TEST
|
|
|
|
config GENERIC_PINCONF
|
|
bool
|
|
select PINCONF
|
|
|
|
config DEBUG_PINCTRL
|
|
bool "Debug PINCTRL calls"
|
|
depends on DEBUG_KERNEL
|
|
help
|
|
Say Y here to add some extra checks and diagnostics to PINCTRL calls.
|
|
|
|
config PINCTRL_AMD
|
|
bool "AMD GPIO pin control"
|
|
depends on HAS_IOMEM
|
|
depends on ACPI || COMPILE_TEST
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select PINMUX
|
|
select PINCONF
|
|
select GENERIC_PINCONF
|
|
help
|
|
The driver for memory mapped GPIO functionality on AMD platforms
|
|
(x86 or arm). Most of the pins are usually muxed to some other
|
|
functionality by firmware, so only a small amount is available
|
|
for GPIO use.
|
|
|
|
Requires ACPI/FDT device enumeration code to set up a platform
|
|
device.
|
|
|
|
config PINCTRL_APPLE_GPIO
|
|
tristate "Apple SoC GPIO pin controller driver"
|
|
depends on ARCH_APPLE
|
|
select PINMUX
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select GENERIC_PINCTRL_GROUPS
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
select OF_GPIO
|
|
help
|
|
This is the driver for the GPIO controller found on Apple ARM SoCs,
|
|
including M1.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pinctrl-apple-gpio.
|
|
|
|
config PINCTRL_ARTPEC6
|
|
bool "Axis ARTPEC-6 pin controller driver"
|
|
depends on MACH_ARTPEC6
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
This is the driver for the Axis ARTPEC-6 pin controller. This driver
|
|
supports pin function multiplexing as well as pin bias and drive
|
|
strength configuration. Device tree integration instructions can be
|
|
found in Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt
|
|
|
|
config PINCTRL_AS3722
|
|
tristate "Pinctrl and GPIO driver for ams AS3722 PMIC"
|
|
depends on MFD_AS3722 && GPIOLIB
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
AS3722 device supports the configuration of GPIO pins for different
|
|
functionality. This driver supports the pinmux, push-pull and
|
|
open drain configuration for the GPIO pins of AS3722 devices. It also
|
|
supports the GPIO functionality through gpiolib.
|
|
|
|
config PINCTRL_AT91
|
|
bool "AT91 pinctrl driver"
|
|
depends on OF
|
|
depends on ARCH_AT91
|
|
select PINMUX
|
|
select PINCONF
|
|
select GPIOLIB
|
|
select OF_GPIO
|
|
select GPIOLIB_IRQCHIP
|
|
help
|
|
Say Y here to enable the at91 pinctrl driver
|
|
|
|
config PINCTRL_AT91PIO4
|
|
bool "AT91 PIO4 pinctrl driver"
|
|
depends on OF
|
|
depends on HAS_IOMEM
|
|
depends on ARCH_AT91 || COMPILE_TEST
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select OF_GPIO
|
|
help
|
|
Say Y here to enable the at91 pinctrl/gpio driver for Atmel PIO4
|
|
controller available on sama5d2 SoC.
|
|
|
|
config PINCTRL_AXP209
|
|
tristate "X-Powers AXP209 PMIC pinctrl and GPIO Support"
|
|
depends on MFD_AXP20X
|
|
depends on OF
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
select GPIOLIB
|
|
help
|
|
AXP PMICs provides multiple GPIOs that can be muxed for different
|
|
functions. This driver bundles a pinctrl driver to select the function
|
|
muxing and a GPIO driver to handle the GPIO when the GPIO function is
|
|
selected.
|
|
Say Y to enable pinctrl and GPIO support for the AXP209 PMIC.
|
|
|
|
config PINCTRL_BM1880
|
|
bool "Bitmain BM1880 Pinctrl driver"
|
|
depends on OF && (ARCH_BITMAIN || COMPILE_TEST)
|
|
default ARCH_BITMAIN
|
|
select PINMUX
|
|
help
|
|
Pinctrl driver for Bitmain BM1880 SoC.
|
|
|
|
config PINCTRL_CY8C95X0
|
|
tristate "Cypress CY8C95X0 I2C pinctrl and GPIO driver"
|
|
depends on I2C
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select PINMUX
|
|
select PINCONF
|
|
select GENERIC_PINCONF
|
|
select REGMAP_I2C
|
|
help
|
|
Support for 20/40/60 pin Cypress Cy8C95x0 pinctrl/gpio I2C expander.
|
|
This driver can also be built as a module. If so, the module will be
|
|
called pinctrl-cy8c95x0.
|
|
|
|
config PINCTRL_DA850_PUPD
|
|
tristate "TI DA850/OMAP-L138/AM18XX pull-up and pull-down groups"
|
|
depends on OF && (ARCH_DAVINCI_DA850 || COMPILE_TEST)
|
|
select PINCONF
|
|
select GENERIC_PINCONF
|
|
help
|
|
Driver for TI DA850/OMAP-L138/AM18XX pinconf. Used to control
|
|
pull-up and pull-down pin groups.
|
|
|
|
config PINCTRL_DA9062
|
|
tristate "Dialog Semiconductor DA9062 PMIC pinctrl and GPIO Support"
|
|
depends on MFD_DA9062
|
|
select GPIOLIB
|
|
help
|
|
The Dialog DA9062 PMIC provides multiple GPIOs that can be muxed for
|
|
different functions. This driver bundles a pinctrl driver to select the
|
|
function muxing and a GPIO driver to handle the GPIO when the GPIO
|
|
function is selected.
|
|
|
|
Say Y to enable pinctrl and GPIO support for the DA9062 PMIC.
|
|
|
|
config PINCTRL_DIGICOLOR
|
|
bool
|
|
depends on ARCH_DIGICOLOR || COMPILE_TEST
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
|
|
config PINCTRL_EQUILIBRIUM
|
|
tristate "Generic pinctrl and GPIO driver for Intel Lightning Mountain SoC"
|
|
depends on OF && HAS_IOMEM
|
|
depends on X86 || COMPILE_TEST
|
|
select PINMUX
|
|
select PINCONF
|
|
select GPIOLIB
|
|
select GPIO_GENERIC
|
|
select GPIOLIB_IRQCHIP
|
|
select GENERIC_PINCONF
|
|
select GENERIC_PINCTRL_GROUPS
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
help
|
|
Equilibrium driver is a pinctrl and GPIO driver for Intel Lightning
|
|
Mountain network processor SoC that supports both the GPIO and pin
|
|
control frameworks. It provides interfaces to setup pin muxing, assign
|
|
desired pin functions, configure GPIO attributes for LGM SoC pins.
|
|
Pin muxing and pin config settings are retrieved from device tree.
|
|
|
|
config PINCTRL_GEMINI
|
|
bool
|
|
depends on ARCH_GEMINI
|
|
default ARCH_GEMINI
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
select MFD_SYSCON
|
|
|
|
config PINCTRL_INGENIC
|
|
bool "Pinctrl driver for the Ingenic JZ47xx SoCs"
|
|
default MACH_INGENIC
|
|
depends on OF
|
|
depends on MIPS || COMPILE_TEST
|
|
select GENERIC_PINCONF
|
|
select GENERIC_PINCTRL_GROUPS
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select REGMAP_MMIO
|
|
|
|
config PINCTRL_K210
|
|
bool "Pinctrl driver for the Canaan Kendryte K210 SoC"
|
|
depends on RISCV && SOC_CANAAN && OF
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
select GENERIC_PINCONF
|
|
select GPIOLIB
|
|
select OF_GPIO
|
|
select REGMAP_MMIO
|
|
default SOC_CANAAN
|
|
help
|
|
Add support for the Canaan Kendryte K210 RISC-V SOC Field
|
|
Programmable IO Array (FPIOA) controller.
|
|
|
|
config PINCTRL_KEEMBAY
|
|
tristate "Pinctrl driver for Intel Keem Bay SoC"
|
|
depends on ARCH_KEEMBAY || (ARM64 && COMPILE_TEST)
|
|
depends on HAS_IOMEM
|
|
select PINMUX
|
|
select PINCONF
|
|
select GENERIC_PINCONF
|
|
select GENERIC_PINCTRL_GROUPS
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select GPIO_GENERIC
|
|
help
|
|
This selects pin control driver for the Intel Keem Bay SoC.
|
|
It provides pin config functions such as pull-up, pull-down,
|
|
interrupt, drive strength, sec lock, Schmitt trigger, slew
|
|
rate control and direction control. This module will be
|
|
called as pinctrl-keembay.
|
|
|
|
config PINCTRL_LANTIQ
|
|
bool
|
|
depends on LANTIQ
|
|
select PINMUX
|
|
select PINCONF
|
|
|
|
config PINCTRL_FALCON
|
|
bool
|
|
depends on SOC_FALCON
|
|
depends on PINCTRL_LANTIQ
|
|
|
|
config PINCTRL_LOONGSON2
|
|
tristate "Pinctrl driver for the Loongson-2 SoC"
|
|
depends on OF && (LOONGARCH || COMPILE_TEST)
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
This selects pin control driver for the Loongson-2 SoC. It
|
|
provides pin config functions multiplexing. GPIO pin pull-up,
|
|
pull-down functions are not supported. Say yes to enable
|
|
pinctrl for Loongson-2 SoC.
|
|
|
|
config PINCTRL_XWAY
|
|
bool
|
|
depends on SOC_TYPE_XWAY
|
|
depends on PINCTRL_LANTIQ
|
|
|
|
config PINCTRL_LPC18XX
|
|
bool "NXP LPC18XX/43XX SCU pinctrl driver"
|
|
depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
|
|
default ARCH_LPC18XX
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
Pinctrl driver for NXP LPC18xx/43xx System Control Unit (SCU).
|
|
|
|
config PINCTRL_MAX77620
|
|
tristate "MAX77620/MAX20024 Pincontrol support"
|
|
depends on MFD_MAX77620 && OF
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
Say Y here to enable Pin control support for Maxim MAX77620 PMIC.
|
|
This PMIC has 8 GPIO pins that work as GPIO as well as special
|
|
function in alternate mode. This driver also configure push-pull,
|
|
open drain, FPS slots etc.
|
|
|
|
config PINCTRL_MCP23S08_I2C
|
|
tristate
|
|
select REGMAP_I2C
|
|
|
|
config PINCTRL_MCP23S08_SPI
|
|
tristate
|
|
select REGMAP_SPI
|
|
|
|
config PINCTRL_MCP23S08
|
|
tristate "Microchip MCP23xxx I/O expander"
|
|
depends on SPI_MASTER || I2C
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select GENERIC_PINCONF
|
|
select PINCTRL_MCP23S08_I2C if I2C
|
|
select PINCTRL_MCP23S08_SPI if SPI_MASTER
|
|
help
|
|
SPI/I2C driver for Microchip MCP23S08 / MCP23S17 / MCP23S18 /
|
|
MCP23008 / MCP23017 / MCP23018 I/O expanders.
|
|
This provides a GPIO interface supporting inputs and outputs and a
|
|
corresponding interrupt-controller.
|
|
|
|
config PINCTRL_MICROCHIP_SGPIO
|
|
tristate "Pinctrl driver for Microsemi/Microchip Serial GPIO"
|
|
depends on OF
|
|
depends on HAS_IOMEM
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select GENERIC_PINCONF
|
|
select GENERIC_PINCTRL_GROUPS
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
select OF_GPIO
|
|
help
|
|
Support for the serial GPIO interface used on Microsemi and
|
|
Microchip SoCs. By using a serial interface, the SIO
|
|
controller significantly extends the number of available
|
|
GPIOs with a minimum number of additional pins on the
|
|
device. The primary purpose of the SIO controller is to
|
|
connect control signals from SFP modules and to act as an
|
|
LED controller.
|
|
|
|
If compiled as a module, the module name will be
|
|
pinctrl-microchip-sgpio.
|
|
|
|
config PINCTRL_OCELOT
|
|
tristate "Pinctrl driver for the Microsemi Ocelot and Jaguar2 SoCs"
|
|
depends on OF
|
|
depends on HAS_IOMEM
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select GENERIC_PINCONF
|
|
select GENERIC_PINCTRL_GROUPS
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
select OF_GPIO
|
|
select REGMAP_MMIO
|
|
help
|
|
Support for the internal GPIO interfaces on Microsemi Ocelot and
|
|
Jaguar2 SoCs.
|
|
|
|
If conpiled as a module, the module name will be pinctrl-ocelot.
|
|
|
|
config PINCTRL_PALMAS
|
|
tristate "Pinctrl driver for the PALMAS Series MFD devices"
|
|
depends on OF && MFD_PALMAS
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
Palmas device supports the configuration of pins for different
|
|
functionality. This driver supports the pinmux, push-pull and
|
|
open drain configuration for the Palmas series devices like
|
|
TPS65913, TPS80036 etc.
|
|
|
|
config PINCTRL_PEF2256
|
|
tristate "Lantiq PEF2256 (FALC56) pin controller driver"
|
|
depends on OF && FRAMER_PEF2256
|
|
select PINMUX
|
|
select PINCONF
|
|
select GENERIC_PINCONF
|
|
help
|
|
This option enables the pin controller support for the Lantiq PEF2256
|
|
framer, also known as FALC56.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pinctrl-pef2256.
|
|
|
|
config PINCTRL_PIC32
|
|
bool "Microchip PIC32 pin controller driver"
|
|
depends on OF
|
|
depends on MACH_PIC32
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
select GPIOLIB_IRQCHIP
|
|
select OF_GPIO
|
|
help
|
|
This is the pin controller and gpio driver for Microchip PIC32
|
|
microcontrollers. This option is selected automatically when specific
|
|
machine and arch are selected to build.
|
|
|
|
config PINCTRL_PIC32MZDA
|
|
def_bool y if PIC32MZDA
|
|
select PINCTRL_PIC32
|
|
|
|
config PINCTRL_PISTACHIO
|
|
bool "IMG Pistachio SoC pinctrl driver"
|
|
depends on OF && (MIPS || COMPILE_TEST)
|
|
depends on GPIOLIB
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
select GPIOLIB_IRQCHIP
|
|
select OF_GPIO
|
|
help
|
|
This support pinctrl and GPIO driver for IMG Pistachio SoC.
|
|
|
|
config PINCTRL_RK805
|
|
tristate "Pinctrl and GPIO driver for RK805 PMIC"
|
|
depends on MFD_RK8XX
|
|
select GPIOLIB
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
This selects the pinctrl driver for RK805.
|
|
|
|
config PINCTRL_ROCKCHIP
|
|
tristate "Rockchip gpio and pinctrl driver"
|
|
depends on ARCH_ROCKCHIP || COMPILE_TEST
|
|
depends on OF
|
|
select GPIOLIB
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
select GENERIC_IRQ_CHIP
|
|
select MFD_SYSCON
|
|
select OF_GPIO
|
|
default ARCH_ROCKCHIP
|
|
help
|
|
This support pinctrl and GPIO driver for Rockchip SoCs.
|
|
|
|
config PINCTRL_SINGLE
|
|
tristate "One-register-per-pin type device tree based pinctrl driver"
|
|
depends on OF
|
|
depends on HAS_IOMEM
|
|
select GENERIC_PINCTRL_GROUPS
|
|
select GENERIC_PINMUX_FUNCTIONS
|
|
select GENERIC_PINCONF
|
|
help
|
|
This selects the device tree based generic pinctrl driver.
|
|
|
|
config PINCTRL_ST
|
|
bool
|
|
depends on OF
|
|
select PINMUX
|
|
select PINCONF
|
|
select GPIOLIB_IRQCHIP
|
|
|
|
config PINCTRL_STMFX
|
|
tristate "STMicroelectronics STMFX GPIO expander pinctrl driver"
|
|
depends on I2C
|
|
depends on OF_GPIO
|
|
select GENERIC_PINCONF
|
|
select GPIOLIB_IRQCHIP
|
|
select MFD_STMFX
|
|
help
|
|
Driver for STMicroelectronics Multi-Function eXpander (STMFX)
|
|
GPIO expander.
|
|
This provides a GPIO interface supporting inputs and outputs,
|
|
and configuring push-pull, open-drain, and can also be used as
|
|
interrupt-controller.
|
|
|
|
config PINCTRL_SX150X
|
|
bool "Semtech SX150x I2C GPIO expander pinctrl driver"
|
|
depends on I2C=y
|
|
select PINMUX
|
|
select PINCONF
|
|
select GENERIC_PINCONF
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
select REGMAP
|
|
help
|
|
Say Y here to provide support for Semtech SX150x-series I2C
|
|
GPIO expanders as pinctrl module.
|
|
Compatible models include:
|
|
- 8 bits: sx1508q, sx1502q
|
|
- 16 bits: sx1509q, sx1506q
|
|
|
|
config PINCTRL_TB10X
|
|
bool
|
|
depends on OF && ARC_PLAT_TB10X
|
|
select GPIOLIB
|
|
|
|
config PINCTRL_ZYNQ
|
|
bool "Pinctrl driver for Xilinx Zynq"
|
|
depends on ARCH_ZYNQ
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
help
|
|
This selects the pinctrl driver for Xilinx Zynq.
|
|
|
|
config PINCTRL_ZYNQMP
|
|
tristate "Pinctrl driver for Xilinx ZynqMP"
|
|
depends on ZYNQMP_FIRMWARE
|
|
select PINMUX
|
|
select GENERIC_PINCONF
|
|
default ZYNQMP_FIRMWARE
|
|
help
|
|
This selects the pinctrl driver for Xilinx ZynqMP platform.
|
|
This driver will query the pin information from the firmware
|
|
and allow configuring the pins.
|
|
Configuration can include the mux function to select on those
|
|
pin(s)/group(s), and various pin configuration parameters
|
|
such as pull-up, slew rate, etc.
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pinctrl-zynqmp.
|
|
|
|
config PINCTRL_MLXBF3
|
|
tristate "NVIDIA BlueField-3 SoC Pinctrl driver"
|
|
depends on (MELLANOX_PLATFORM && ARM64) || COMPILE_TEST
|
|
select PINMUX
|
|
select GPIOLIB
|
|
select GPIOLIB_IRQCHIP
|
|
help
|
|
Say Y to select the pinctrl driver for BlueField-3 SoCs.
|
|
This pin controller allows selecting the mux function for
|
|
each pin. This driver can also be built as a module called
|
|
pinctrl-mlxbf3.
|
|
|
|
source "drivers/pinctrl/actions/Kconfig"
|
|
source "drivers/pinctrl/aspeed/Kconfig"
|
|
source "drivers/pinctrl/bcm/Kconfig"
|
|
source "drivers/pinctrl/berlin/Kconfig"
|
|
source "drivers/pinctrl/cirrus/Kconfig"
|
|
source "drivers/pinctrl/freescale/Kconfig"
|
|
source "drivers/pinctrl/intel/Kconfig"
|
|
source "drivers/pinctrl/mediatek/Kconfig"
|
|
source "drivers/pinctrl/meson/Kconfig"
|
|
source "drivers/pinctrl/mvebu/Kconfig"
|
|
source "drivers/pinctrl/nomadik/Kconfig"
|
|
source "drivers/pinctrl/nuvoton/Kconfig"
|
|
source "drivers/pinctrl/nxp/Kconfig"
|
|
source "drivers/pinctrl/pxa/Kconfig"
|
|
source "drivers/pinctrl/qcom/Kconfig"
|
|
source "drivers/pinctrl/realtek/Kconfig"
|
|
source "drivers/pinctrl/renesas/Kconfig"
|
|
source "drivers/pinctrl/samsung/Kconfig"
|
|
source "drivers/pinctrl/spear/Kconfig"
|
|
source "drivers/pinctrl/sprd/Kconfig"
|
|
source "drivers/pinctrl/starfive/Kconfig"
|
|
source "drivers/pinctrl/stm32/Kconfig"
|
|
source "drivers/pinctrl/sunplus/Kconfig"
|
|
source "drivers/pinctrl/sunxi/Kconfig"
|
|
source "drivers/pinctrl/tegra/Kconfig"
|
|
source "drivers/pinctrl/ti/Kconfig"
|
|
source "drivers/pinctrl/uniphier/Kconfig"
|
|
source "drivers/pinctrl/visconti/Kconfig"
|
|
source "drivers/pinctrl/vt8500/Kconfig"
|
|
|
|
endif
|