linux/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
Stefan Wahren ab1b4ef966 ARM: dts: bcm2835-rpi-zero-w: Drop unnecessary pinctrl
There is no need to specify a pinctrl for the reset GPIO. So we better
remove this avoid a potential conflict between pinctrl and pwrseq
after the pinmux driver has been changed to strict:

pinctrl-bcm2835 20200000.gpio: pin gpio41 already requested by wifi-pwrseq;
cannot claim for pinctrl-bcm2835:499
pinctrl-bcm2835 20200000.gpio: pin-41 (pinctrl-bcm2835:499) status -22
pwrseq_simple: probe of wifi-pwrseq failed with error -22

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
2019-02-01 11:56:32 +01:00

136 lines
2.5 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
*/
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-usb-otg.dtsi"
/ {
compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
model = "Raspberry Pi Zero W";
chosen {
/* 8250 auxiliary UART instead of pl011 */
stdout-path = "serial1:115200n8";
};
leds {
act {
gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
};
};
&gpio {
/*
* This is based on the official GPU firmware DT blob.
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "ID_SDA",
"ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"NC", /* GPIO30 */
"NC", /* GPIO31 */
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"NC", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"CAM_GPIO1", /* GPIO40 */
"WL_ON", /* GPIO41 */
"NC", /* GPIO42 */
"WIFI_CLK", /* GPIO43 */
"CAM_GPIO0", /* GPIO44 */
"BT_ON", /* GPIO45 */
"HDMI_HPD_N",
"STATUS_LED_N",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0>;
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&sdhci {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
mmc-pwrseq = <&wifi_pwrseq>;
non-removable;
status = "okay";
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
status = "okay";
bluetooth {
compatible = "brcm,bcm43438-bt";
max-speed = <2000000>;
shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
};
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_gpio14>;
status = "okay";
};