linux/drivers/usb/dwc3/gadget.c

// SPDX-License-Identifier: GPL-2.0
/*
 * gadget.c - DesignWare USB3 DRD Controller Gadget Framework Link
 *
 * Copyright (C) 2010-2011 Texas Instruments Incorporated - https://www.ti.com
 *
 * Authors: Felipe Balbi <balbi@ti.com>,
 *	    Sebastian Andrzej Siewior <bigeasy@linutronix.de>
 */

#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/list.h>
#include <linux/dma-mapping.h>

#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>

#include "debug.h"
#include "core.h"
#include "gadget.h"
#include "io.h"

#define DWC3_ALIGN_FRAME(d, n)	(((d)->frame_number + ((d)->interval * (n))) \
					& ~((d)->interval - 1))

/**
 * dwc3_gadget_set_test_mode - enables usb2 test modes
 * @dwc: pointer to our context structure
 * @mode: the mode to set (J, K SE0 NAK, Force Enable)
 *
 * Caller should take care of locking. This function will return 0 on
 * success or -EINVAL if wrong Test Selector is passed.
 */
int dwc3_gadget_set_test_mode(struct dwc3 *dwc, int mode)
{
	u32		reg;

	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
	reg &= ~DWC3_DCTL_TSTCTRL_MASK;

	switch (mode) {
	case USB_TEST_J:
	case USB_TEST_K:
	case USB_TEST_SE0_NAK:
	case USB_TEST_PACKET:
	case USB_TEST_FORCE_ENABLE:
		reg |= mode << 1;
		break;
	default:
		return -EINVAL;
	}

	dwc3_gadget_dctl_write_safe(dwc, reg);

	return 0;
}

/**
 * dwc3_gadget_get_link_state - gets current state of usb link
 * @dwc: pointer to our context structure
 *
 * Caller should take care of locking. This function will
 * return the link state on success (>= 0) or -ETIMEDOUT.
 */
int dwc3_gadget_get_link_state(struct dwc3 *dwc)
{
	u32		reg;

	reg = dwc3_readl(dwc->regs, DWC3_DSTS);

	return DWC3_DSTS_USBLNKST(reg);
}

/**
 * dwc3_gadget_set_link_state - sets usb link to a particular state
 * @dwc: pointer to our context structure
 * @state: the state to put link into
 *
 * Caller should take care of locking. This function will
 * return 0 on success or -ETIMEDOUT.
 */
int dwc3_gadget_set_link_state(struct dwc3 *dwc, enum dwc3_link_state state)
{
	int		retries = 10000;
	u32		reg;

	/*
	 * Wait until device controller is ready. Only applies to 1.94a and
	 * later RTL.
	 */
	if (!DWC3_VER_IS_PRIOR(DWC3, 194A)) {
		while (--retries) {
			reg = dwc3_readl(dwc->regs, DWC3_DSTS);
			if (reg & DWC3_DSTS_DCNRD)
				udelay(5);
			else
				break;
		}

		if (retries <= 0)
			return -ETIMEDOUT;
	}

	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
	reg &= ~DWC3_DCTL_ULSTCHNGREQ_MASK;

	/* set no action before sending new link state change */
	dwc3_writel(dwc->regs, DWC3_DCTL, reg);

	/* set requested state */
	reg |= DWC3_DCTL_ULSTCHNGREQ(state);
	dwc3_writel(dwc->regs, DWC3_DCTL, reg);

	/*
	 * The following code is racy when called from dwc3_gadget_wakeup,
	 * and is not needed, at least on newer versions
	 */
	if (!DWC3_VER_IS_PRIOR(DWC3, 194A))
		return 0;

	/* wait for a change in DSTS */
	retries = 10000;
	while (--retries) {
		reg = dwc3_readl(dwc->regs, DWC3_DSTS);

		if (DWC3_DSTS_USBLNKST(reg) == state)
			return 0;

		udelay(5);
	}

	return -ETIMEDOUT;
}

/**
 * dwc3_ep_inc_trb - increment a trb index.
 * @index: Pointer to the TRB index to increment.
 *
 * The index should never point to the link TRB. After incrementing,
 * if it is point to the link TRB, wrap around to the beginning. The
 * link TRB is always at the last TRB entry.
 */
static void dwc3_ep_inc_trb(u8 *index)
{
	(*index)++;
	if (*index == (DWC3_TRB_NUM - 1))
		*index = 0;
}

/**
 * dwc3_ep_inc_enq - increment endpoint's enqueue pointer
 * @dep: The endpoint whose enqueue pointer we're incrementing
 */
static void dwc3_ep_inc_enq(struct dwc3_ep *dep)
{
	dwc3_ep_inc_trb(&dep->trb_enqueue);
}

/**
 * dwc3_ep_inc_deq - increment endpoint's dequeue pointer
 * @dep: The endpoint whose enqueue pointer we're incrementing
 */
static void dwc3_ep_inc_deq(struct dwc3_ep *dep)
{
	dwc3_ep_inc_trb(&dep->trb_dequeue);
}

static void dwc3_gadget_del_and_unmap_request(struct dwc3_ep *dep,
		struct dwc3_request *req, int status)
{
	struct dwc3			*dwc = dep->dwc;

	list_del(&req->list);
	req->remaining = 0;
	req->needs_extra_trb = false;

	if (req->request.status == -EINPROGRESS)
		req->request.status = status;

	if (req->trb)
		usb_gadget_unmap_request_by_dev(dwc->sysdev,
				&req->request, req->direction);

	req->trb = NULL;
	trace_dwc3_gadget_giveback(req);

	if (dep->number > 1)
		pm_runtime_put(dwc->dev);
}

/**
 * dwc3_gadget_giveback - call struct usb_request's ->complete callback
 * @dep: The endpoint to whom the request belongs to
 * @req: The request we're giving back
 * @status: completion code for the request
 *
 * Must be called with controller's lock held and interrupts disabled. This
 * function will unmap @req and call its ->complete() callback to notify upper
 * layers that it has completed.
 */
void dwc3_gadget_giveback(struct dwc3_ep *dep, struct dwc3_request *req,
		int status)
{
	struct dwc3			*dwc = dep->dwc;

	dwc3_gadget_del_and_unmap_request(dep, req, status);
	req->status = DWC3_REQUEST_STATUS_COMPLETED;

	spin_unlock(&dwc->lock);
	usb_gadget_giveback_request(&dep->endpoint, &req->request);
	spin_lock(&dwc->lock);
}

/**
 * dwc3_send_gadget_generic_command - issue a generic command for the controller
 * @dwc: pointer to the controller context
 * @cmd: the command to be issued
 * @param: command parameter
 *
 * Caller should take care of locking. Issue @cmd with a given @param to @dwc
 * and wait for its completion.
 */
int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
		u32 param)
{
	u32		timeout = 500;
	int		status = 0;
	int		ret = 0;
	u32		reg;

	dwc3_writel(dwc->regs, DWC3_DGCMDPAR, param);
	dwc3_writel(dwc->regs, DWC3_DGCMD, cmd | DWC3_DGCMD_CMDACT);

	do {
		reg = dwc3_readl(dwc->regs, DWC3_DGCMD);
		if (!(reg & DWC3_DGCMD_CMDACT)) {
			status = DWC3_DGCMD_STATUS(reg);
			if (status)
				ret = -EINVAL;
			break;
		}
	} while (--timeout);

	if (!timeout) {
		ret = -ETIMEDOUT;
		status = -ETIMEDOUT;
	}

	trace_dwc3_gadget_generic_cmd(cmd, param, status);

	return ret;
}

static int __dwc3_gadget_wakeup(struct dwc3 *dwc);

/**
 * dwc3_send_gadget_ep_cmd - issue an endpoint command
 * @dep: the endpoint to which the command is going to be issued
 * @cmd: the command to be issued
 * @params: parameters to the command
 *
 * Caller should handle locking. This function will issue @cmd with given
 * @params to @dep and wait for its completion.
 */
int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
		struct dwc3_gadget_ep_cmd_params *params)
{
	const struct usb_endpoint_descriptor *desc = dep->endpoint.desc;
	struct dwc3		*dwc = dep->dwc;
	u32			timeout = 5000;
	u32			saved_config = 0;
	u32			reg;

	int			cmd_status = 0;
	int			ret = -EINVAL;

	/*
	 * When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
	 * GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an
	 * endpoint command.
	 *
	 * Save and clear both GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY
	 * settings. Restore them after the command is completed.
	 *
	 * DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
	 */
	if (dwc->gadget->speed <= USB_SPEED_HIGH) {
		reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
		if (unlikely(reg & DWC3_GUSB2PHYCFG_SUSPHY)) {
			saved_config |= DWC3_GUSB2PHYCFG_SUSPHY;
			reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
		}

		if (reg & DWC3_GUSB2PHYCFG_ENBLSLPM) {
			saved_config |= DWC3_GUSB2PHYCFG_ENBLSLPM;
			reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
		}

		if (saved_config)
			dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
	}

	if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) {
		int link_state;

		/*
		 * Initiate remote wakeup if the link state is in U3 when
		 * operating in SS/SSP or L1/L2 when operating in HS/FS. If the
		 * link state is in U1/U2, no remote wakeup is needed. The Start
		 * Transfer command will initiate the link recovery.
		 */
		link_state = dwc3_gadget_get_link_state(dwc);
		switch (link_state) {
		case DWC3_LINK_STATE_U2:
			if (dwc->gadget->speed >= USB_SPEED_SUPER)
				break;

			fallthrough;
		case DWC3_LINK_STATE_U3:
			ret = __dwc3_gadget_wakeup(dwc);
			dev_WARN_ONCE(dwc->dev, ret, "wakeup failed --> %d\n",
					ret);
			break;
		}
	}

	/*
	 * For some commands such as Update Transfer command, DEPCMDPARn
	 * registers are reserved. Since the driver often sends Update Transfer
	 * command, don't write to DEPCMDPARn to avoid register write delays and
	 * improve performance.
	 */
	if (DWC3_DEPCMD_CMD(cmd) != DWC3_DEPCMD_UPDATETRANSFER) {
		dwc3_writel(dep->regs, DWC3_DEPCMDPAR0, params->param0);
		dwc3_writel(dep->regs, DWC3_DEPCMDPAR1, params->param1);
		dwc3_writel(dep->regs, DWC3_DEPCMDPAR2, params->param2);
	}

	/*
	 * Synopsys Databook 2.60a states in section 6.3.2.5.6 of that if we're
	 * not relying on XferNotReady, we can make use of a special "No
	 * Response Update Transfer" command where we should clear both CmdAct
	 * and CmdIOC bits.
	 *
	 * With this, we don't need to wait for command completion and can
	 * straight away issue further commands to the endpoint.
	 *
	 * NOTICE: We're making an assumption that control endpoints will never
	 * make use of Update Transfer command. This is a safe assumption
	 * because we can never have more than one request at a time with
	 * Control Endpoints. If anybody changes that assumption, this chunk
	 * needs to be updated accordingly.
	 */
	if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_UPDATETRANSFER &&
			!usb_endpoint_xfer_isoc(desc))
		cmd &= ~(DWC3_DEPCMD_CMDIOC | DWC3_DEPCMD_CMDACT);
	else
		cmd |= DWC3_DEPCMD_CMDACT;

	dwc3_writel(dep->regs, DWC3_DEPCMD, cmd);

	if (!(cmd & DWC3_DEPCMD_CMDACT)) {
		ret = 0;
		goto skip_status;
	}

	do {
		reg = dwc3_readl(dep->regs, DWC3_DEPCMD);
		if (!(reg & DWC3_DEPCMD_CMDACT)) {
			cmd_status = DWC3_DEPCMD_STATUS(reg);

			switch (cmd_status) {
			case 0:
				ret = 0;
				break;
			case DEPEVT_TRANSFER_NO_RESOURCE:
				dev_WARN(dwc->dev, "No resource for %s\n",
					 dep->name);
				ret = -EINVAL;
				break;
			case DEPEVT_TRANSFER_BUS_EXPIRY:
				/*
				 * SW issues START TRANSFER command to
				 * isochronous ep with future frame interval. If
				 * future interval time has already passed when
				 * core receives the command, it will respond
				 * with an error status of 'Bus Expiry'.
				 *
				 * Instead of always returning -EINVAL, let's
				 * give a hint to the gadget driver that this is
				 * the case by returning -EAGAIN.
				 */
				ret = -EAGAIN;
				break;
			default:
				dev_WARN(dwc->dev, "UNKNOWN cmd status\n");
			}

			break;
		}
	} while (--timeout);

	if (timeout == 0) {
		ret = -ETIMEDOUT;
		cmd_status = -ETIMEDOUT;
	}

skip_status:
	trace_dwc3_gadget_ep_cmd(dep, cmd, params, cmd_status);

	if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) {
		if (ret == 0)
			dep->flags |= DWC3_EP_TRANSFER_STARTED;

		if (ret != -ETIMEDOUT)
			dwc3_gadget_ep_get_transfer_index(dep);
	}

	if (saved_config) {
		reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
		reg |= saved_config;
		dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
	}

	return ret;
}

static int dwc3_send_clear_stall_ep_cmd(struct dwc3_ep *dep)
{
	struct dwc3 *dwc = dep->dwc;
	struct dwc3_gadget_ep_cmd_params params;
	u32 cmd = DWC3_DEPCMD_CLEARSTALL;

	/*
	 * As of core revision 2.60a the recommended programming model
	 * is to set the ClearPendIN bit when issuing a Clear Stall EP
	 * command for IN endpoints. This is to prevent an issue where
	 * some (non-compliant) hosts may not send ACK TPs for pending
	 * IN transfers due to a mishandled error condition. Synopsys
	 * STAR 9000614252.
	 */
	if (dep->direction &&
	    !DWC3_VER_IS_PRIOR(DWC3, 260A) &&
	    (dwc->gadget->speed >= USB_SPEED_SUPER))
		cmd |= DWC3_DEPCMD_CLEARPENDIN;

	memset(&params, 0, sizeof(params));

	return dwc3_send_gadget_ep_cmd(dep, cmd, &params);
}

static dma_addr_t dwc3_trb_dma_offset(struct dwc3_ep *dep,
		struct dwc3_trb *trb)
{
	u32		offset = (char *) trb - (char *) dep->trb_pool;

	return dep->trb_pool_dma + offset;
}

static int dwc3_alloc_trb_pool(struct dwc3_ep *dep)
{
	struct dwc3		*dwc = dep->dwc;

	if (dep->trb_pool)
		return 0;

	dep->trb_pool = dma_alloc_coherent(dwc->sysdev,
			sizeof(struct dwc3_trb) * DWC3_TRB_NUM,
			&dep->trb_pool_dma, GFP_KERNEL);
	if (!dep->trb_pool) {
		dev_err(dep->dwc->dev, "failed to allocate trb pool for %s\n",
				dep->name);
		return -ENOMEM;
	}

	return 0;
}

static void dwc3_free_trb_pool(struct dwc3_ep *dep)
{
	struct dwc3		*dwc = dep->dwc;

	dma_free_coherent(dwc->sysdev, sizeof(struct dwc3_trb) * DWC3_TRB_NUM,
			dep->trb_pool, dep->trb_pool_dma);

	dep->trb_pool = NULL;
	dep->trb_pool_dma = 0;
}

static int dwc3_gadget_set_xfer_resource(struct dwc3_ep *dep)
{
	struct dwc3_gadget_ep_cmd_params params;

	memset(&params, 0x00, sizeof(params));

	params.param0 = DWC3_DEPXFERCFG_NUM_XFER_RES(1);

	return dwc3_send_gadget_ep_cmd(dep, DWC3_DEPCMD_SETTRANSFRESOURCE,
			&params);
}

/**
 * dwc3_gadget_start_config - configure ep resources
 * @dep: endpoint that is being enabled
 *
 * Issue a %DWC3_DEPCMD_DEPSTARTCFG command to @dep. After the command's
 * completion, it will set Transfer Resource for all available endpoints.
 *
 * The assignment of transfer resources cannot perfectly follow the data book
 * due to the fact that the controller driver does not have all knowledge of the
 * configuration in advance. It is given this information piecemeal by the
 * composite gadget framework after every SET_CONFIGURATION and
 * SET_INTERFACE. Trying to follow the databook programming model in this
 * scenario can cause errors. For two reasons:
 *
 * 1) The databook says to do %DWC3_DEPCMD_DEPSTARTCFG for every
 * %USB_REQ_SET_CONFIGURATION and %USB_REQ_SET_INTERFACE (8.1.5). This is
 * incorrect in the scenario of multiple interfaces.
 *
 * 2) The databook does not mention doing more %DWC3_DEPCMD_DEPXFERCFG for new
 * endpoint on alt setting (8.1.6).
 *
 * The following simplified method is used instead:
 *
 * All hardware endpoints can be assigned a transfer resource and this setting
 * will stay persistent until either a core reset or hibernation. So whenever we
 * do a %DWC3_DEPCMD_DEPSTARTCFG(0) we can go ahead and do
 * %DWC3_DEPCMD_DEPXFERCFG for every hardware endpoint as well. We are
 * guaranteed that there are as many transfer resources as endpoints.
 *
 * This function is called for each endpoint when it is being enabled but is
 * triggered only when called for EP0-out, which always happens first, and which
 * should only happen in one of the above conditions.
 */
static int dwc3_gadget_start_config(struct dwc3_ep *dep)
{
	struct dwc3_gadget_ep_cmd_params params;
	struct dwc3		*dwc;
	u32			cmd;
	int			i;
	int			ret;

	if (dep->number)
		return 0;

	memset(&params, 0x00, sizeof(params));
	cmd = DWC3_DEPCMD_DEPSTARTCFG;
	dwc = dep->dwc;

	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
	if (ret)
		return ret;

	for (i = 0; i < DWC3_ENDPOINTS_NUM; i++) {
		struct dwc3_ep *dep = dwc->eps[i];

		if (!dep)
			continue;

		ret = dwc3_gadget_set_xfer_resource(dep);
		if (ret)
			return ret;
	}

	return 0;
}

static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)
{
	const struct usb_ss_ep_comp_descriptor *comp_desc;
	const struct usb_endpoint_descriptor *desc;
	struct dwc3_gadget_ep_cmd_params params;
	struct dwc3 *dwc = dep->dwc;

	comp_desc = dep->endpoint.comp_desc;
	desc = dep->endpoint.desc;

	memset(&params, 0x00, sizeof(params));

	params.param0 = DWC3_DEPCFG_EP_TYPE(usb_endpoint_type(desc))
		| DWC3_DEPCFG_MAX_PACKET_SIZE(usb_endpoint_maxp(desc));

	/* Burst size is only needed in SuperSpeed mode */
	if (dwc->gadget->speed >= USB_SPEED_SUPER) {
		u32 burst = dep->endpoint.maxburst;

		params.param0 |= DWC3_DEPCFG_BURST_SIZE(burst - 1);
	}

	params.param0 |= action;
	if (action == DWC3_DEPCFG_ACTION_RESTORE)
		params.param2 |= dep->saved_state;

	if (usb_endpoint_xfer_control(desc))
		params.param1 = DWC3_DEPCFG_XFER_COMPLETE_EN;

	if (dep->number <= 1 || usb_endpoint_xfer_isoc(desc))
		params.param1 |= DWC3_DEPCFG_XFER_NOT_READY_EN;

	if (usb_ss_max_streams(comp_desc) && usb_endpoint_xfer_bulk(desc)) {
		params.param1 |= DWC3_DEPCFG_STREAM_CAPABLE
			| DWC3_DEPCFG_XFER_COMPLETE_EN
			| DWC3_DEPCFG_STREAM_EVENT_EN;
		dep->stream_capable = true;
	}

	if (!usb_endpoint_xfer_control(desc))
		params.param1 |= DWC3_DEPCFG_XFER_IN_PROGRESS_EN;

	/*
	 * We are doing 1:1 mapping for endpoints, meaning
	 * Physical Endpoints 2 maps to Logical Endpoint 2 and
	 * so on. We consider the direction bit as part of the physical
	 * endpoint number. So USB endpoint 0x81 is 0x03.
	 */
	params.param1 |= DWC3_DEPCFG_EP_NUMBER(dep->number);

	/*
	 * We must use the lower 16 TX FIFOs even though
	 * HW might have more
	 */
	if (dep->direction)
		params.param0 |= DWC3_DEPCFG_FIFO_NUMBER(dep->number >> 1);

	if (desc->bInterval) {
		u8 bInterval_m1;

		/*
		 * Valid range for DEPCFG.bInterval_m1 is from 0 to 13.
		 *
		 * NOTE: The programming guide incorrectly stated bInterval_m1
		 * must be set to 0 when operating in fullspeed. Internally the
		 * controller does not have this limitation. See DWC_usb3x
		 * programming guide section 3.2.2.1.
		 */
		bInterval_m1 = min_t(u8, desc->bInterval - 1, 13);

		if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_INT &&
		    dwc->gadget->speed == USB_SPEED_FULL)
			dep->interval = desc->bInterval;
		else
			dep->interval = 1 << (desc->bInterval - 1);

		params.param1 |= DWC3_DEPCFG_BINTERVAL_M1(bInterval_m1);
	}

	return dwc3_send_gadget_ep_cmd(dep, DWC3_DEPCMD_SETEPCONFIG, &params);
}

/**
 * dwc3_gadget_calc_tx_fifo_size - calculates the txfifo size value
 * @dwc: pointer to the DWC3 context
 * @mult: multiplier to be used when calculating the fifo_size
 *
 * Calculates the size value based on the equation below:
 *
 * DWC3 revision 280A and prior:
 * fifo_size = mult * (max_packet / mdwidth) + 1;
 *
 * DWC3 revision 290A and onwards:
 * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
 *
 * The max packet size is set to 1024, as the txfifo requirements mainly apply
 * to super speed USB use cases.  However, it is safe to overestimate the fifo
 * allocations for other scenarios, i.e. high speed USB.
 */
static int dwc3_gadget_calc_tx_fifo_size(struct dwc3 *dwc, int mult)
{
	int max_packet = 1024;
	int fifo_size;
	int mdwidth;

	mdwidth = dwc3_mdwidth(dwc);

	/* MDWIDTH is represented in bits, we need it in bytes */
	mdwidth >>= 3;

	if (DWC3_VER_IS_PRIOR(DWC3, 290A))
		fifo_size = mult * (max_packet / mdwidth) + 1;
	else
		fifo_size = mult * ((max_packet + mdwidth) / mdwidth) + 1;
	return fifo_size;
}

/**
 * dwc3_gadget_clear_tx_fifos - Clears txfifo allocation
 * @dwc: pointer to the DWC3 context
 *
 * Iterates through all the endpoint registers and clears the previous txfifo
 * allocations.
 */
void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
{
	struct dwc3_ep *dep;
	int fifo_depth;
	int size;
	int num;

	if (!dwc->do_fifo_resize)
		return;

	/* Read ep0IN related TXFIFO size */
	dep = dwc->eps[1];
	size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
	if (DWC3_IP_IS(DWC3))
		fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);
	else
		fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);

	dwc->last_fifo_depth = fifo_depth;
	/* Clear existing TXFIFO for all IN eps except ep0 */
	for (num = 3; num < min_t(int, dwc->num_eps, DWC3_ENDPOINTS_NUM);
	     num += 2) {
		dep = dwc->eps[num];
		/* Don't change TXFRAMNUM on usb31 version */
		size = DWC3_IP_IS(DWC3) ? 0 :
			dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1)) &
				   DWC31_GTXFIFOSIZ_TXFRAMNUM;

		dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1), size);
		dep->flags &= ~DWC3_EP_TXFIFO_RESIZED;
	}
	dwc->num_ep_resized = 0;
}

/*
 * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
 * @dwc: pointer to our context structure
 *
 * This function will a best effort FIFO allocation in order
 * to improve FIFO usage and throughput, while still allowing
 * us to enable as many endpoints as possible.
 *
 * Keep in mind that this operation will be highly dependent
 * on the configured size for RAM1 - which contains TxFifo -,
 * the amount of endpoints enabled on coreConsultant tool, and
 * the width of the Master Bus.
 *
 * In general, FIFO depths are represented with the following equation:
 *
 * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
 *
 * In conjunction with dwc3_gadget_check_config(), this resizing logic will
 * ensure that all endpoints will have enough internal memory for one max
 * packet per endpoint.
 */
static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
{
	struct dwc3 *dwc = dep->dwc;
	int fifo_0_start;
	int ram1_depth;
	int fifo_size;
	int min_depth;
	int num_in_ep;
	int remaining;
	int num_fifos = 1;
	int fifo;
	int tmp;

	if (!dwc->do_fifo_resize)
		return 0;

	/* resize IN endpoints except ep0 */
	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
		return 0;

	/* bail if already resized */
	if (dep->flags & DWC3_EP_TXFIFO_RESIZED)
		return 0;

	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);

	if ((dep->endpoint.maxburst > 1 &&
	     usb_endpoint_xfer_bulk(dep->endpoint.desc)) ||
	    usb_endpoint_xfer_isoc(dep->endpoint.desc))
		num_fifos = 3;

	if (dep->endpoint.maxburst > 6 &&
	    (usb_endpoint_xfer_bulk(dep->endpoint.desc) ||
	     usb_endpoint_xfer_isoc(dep->endpoint.desc)) && DWC3_IP_IS(DWC31))
		num_fifos = dwc->tx_fifo_resize_max_num;

	/* FIFO size for a single buffer */
	fifo = dwc3_gadget_calc_tx_fifo_size(dwc, 1);

	/* Calculate the number of remaining EPs w/o any FIFO */
	num_in_ep = dwc->max_cfg_eps;
	num_in_ep -= dwc->num_ep_resized;

	/* Reserve at least one FIFO for the number of IN EPs */
	min_depth = num_in_ep * (fifo + 1);
	remaining = ram1_depth - min_depth - dwc->last_fifo_depth;
	remaining = max_t(int, 0, remaining);
	/*
	 * We've already reserved 1 FIFO per EP, so check what we can fit in
	 * addition to it.  If there is not enough remaining space, allocate
	 * all the remaining space to the EP.
	 */
	fifo_size = (num_fifos - 1) * fifo;
	if (remaining < fifo_size)
		fifo_size = remaining;

	fifo_size += fifo;
	/* Last increment according to the TX FIFO size equation */
	fifo_size++;

	/* Check if TXFIFOs start at non-zero addr */
	tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
	fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);

	fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));
	if (DWC3_IP_IS(DWC3))
		dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
	else
		dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

	/* Check fifo size allocation doesn't exceed available RAM size. */
	if (dwc->last_fifo_depth >= ram1_depth) {
		dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",
			dwc->last_fifo_depth, ram1_depth,
			dep->endpoint.name, fifo_size);
		if (DWC3_IP_IS(DWC3))
			fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
		else
			fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

		dwc->last_fifo_depth -= fifo_size;
		return -ENOMEM;
	}

	dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);
	dep->flags |= DWC3_EP_TXFIFO_RESIZED;
	dwc->num_ep_resized++;

	return 0;
}

/**
 * __dwc3_gadget_ep_enable - initializes a hw endpoint
 * @dep: endpoint to be initialized
 * @action: one of INIT, MODIFY or RESTORE
 *
 * Caller should take care of locking. Execute all necessary commands to
 * initialize a HW endpoint so it can be used by a gadget driver.
 */
static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
{
	const struct usb_endpoint_descriptor *desc = dep->endpoint.desc;
	struct dwc3		*dwc = dep->dwc;

	u32			reg;
	int			ret;

	if (!(dep->flags & DWC3_EP_ENABLED)) {
		ret = dwc3_gadget_resize_tx_fifos(dep);
		if (ret)
			return ret;

		ret = dwc3_gadget_start_config(dep);
		if (ret)
			return ret;
	}

	ret = dwc3_gadget_set_ep_config(dep, action);
	if (ret)
		return ret;

	if (!(dep->flags & DWC3_EP_ENABLED)) {
		struct dwc3_trb	*trb_st_hw;
		struct dwc3_trb	*trb_link;

		dep->type = usb_endpoint_type(desc);
		dep->flags |= DWC3_EP_ENABLED;

		reg = dwc3_readl(dwc->regs, DWC3_DALEPENA);
		reg |= DWC3_DALEPENA_EP(dep->number);
		dwc3_writel(dwc->regs, DWC3_DALEPENA, reg);

		dep->trb_dequeue = 0;
		dep->trb_enqueue = 0;

		if (usb_endpoint_xfer_control(desc))
			goto out;

		/* Initialize the TRB ring */
		memset(dep->trb_pool, 0,
		       sizeof(struct dwc3_trb) * DWC3_TRB_NUM);

		/* Link TRB. The HWO bit is never reset */
		trb_st_hw = &dep->trb_pool[0];

		trb_link = &dep->trb_pool[DWC3_TRB_NUM - 1];
		trb_link->bpl = lower_32_bits(dwc3_trb_dma_offset(dep, trb_st_hw));
		trb_link->bph = upper_32_bits(dwc3_trb_dma_offset(dep, trb_st_hw));
		trb_link->ctrl |= DWC3_TRBCTL_LINK_TRB;
		trb_link->ctrl |= DWC3_TRB_CTRL_HWO;
	}

	/*
	 * Issue StartTransfer here with no-op TRB so we can always rely on No
	 * Response Update Transfer command.
	 */
	if (usb_endpoint_xfer_bulk(desc) ||
			usb_endpoint_xfer_int(desc)) {
		struct dwc3_gadget_ep_cmd_params params;
		struct dwc3_trb	*trb;
		dma_addr_t trb_dma;
		u32 cmd;

		memset(&params, 0, sizeof(params));
		trb = &dep->trb_pool[0];
		trb_dma = dwc3_trb_dma_offset(dep, trb);

		params.param0 = upper_32_bits(trb_dma);
		params.param1 = lower_32_bits(trb_dma);

		cmd = DWC3_DEPCMD_STARTTRANSFER;

		ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
		if (ret < 0)
			return ret;

		if (dep->stream_capable) {
			/*
			 * For streams, at start, there maybe a race where the
			 * host primes the endpoint before the function driver
			 * queues a request to initiate a stream. In that case,
			 * the controller will not see the prime to generate the
			 * ERDY and start stream. To workaround this, issue a
			 * no-op TRB as normal, but end it immediately. As a
			 * result, when the function driver queues the request,
			 * the next START_TRANSFER command will cause the
			 * controller to generate an ERDY to initiate the
			 * stream.
			 */
			dwc3_stop_active_transfer(dep, true, true);

			/*
			 * All stream eps will reinitiate stream on NoStream
			 * rejection until we can determine that the host can
			 * prime after the first transfer.
			 *
			 * However, if the controller is capable of
			 * TXF_FLUSH_BYPASS, then IN direction endpoints will
			 * automatically restart the stream without the driver
			 * initiation.
			 */
			if (!dep->direction ||
			    !(dwc->hwparams.hwparams9 &
			      DWC3_GHWPARAMS9_DEV_TXF_FLUSH_BYPASS))
				dep->flags |= DWC3_EP_FORCE_RESTART_STREAM;
		}
	}

out:
	trace_dwc3_gadget_ep_enable(dep);

	return 0;
}

static void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep)
{
	struct dwc3_request		*req;

	dwc3_stop_active_transfer(dep, true, false);

	/* - giveback all requests to gadget driver */
	while (!list_empty(&dep->started_list)) {
		req = next_request(&dep->started_list);

		dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
	}

	while (!list_empty(&dep->pending_list)) {
		req = next_request(&dep->pending_list);

		dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
	}

	while (!list_empty(&dep->cancelled_list)) {
		req = next_request(&dep->cancelled_list);

		dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
	}
}

/**
 * __dwc3_gadget_ep_disable - disables a hw endpoint
 * @dep: the endpoint to disable
 *
 * This function undoes what __dwc3_gadget_ep_enable did and also removes
 * requests which are currently being processed by the hardware and those which
 * are not yet scheduled.
 *
 * Caller should take care of locking.
 */
static int __dwc3_gadget_ep_disable(struct dwc3_ep *dep)
{
	struct dwc3		*dwc = dep->dwc;
	u32			reg;

	trace_dwc3_gadget_ep_disable(dep);

	/* make sure HW endpoint isn't stalled */
	if (dep->flags & DWC3_EP_STALL)
		__dwc3_gadget_ep_set_halt(dep, 0, false);

	reg = dwc3_readl(dwc->regs, DWC3_DALEPENA);
	reg &= ~DWC3_DALEPENA_EP(dep->number);
	dwc3_writel(dwc->regs, DWC3_DALEPENA, reg);

	/* Clear out the ep descriptors for non-ep0 */
	if (dep->number > 1) {
		dep->endpoint.comp_desc = NULL;
		dep->endpoint.desc = NULL;
	}

	dwc3_remove_requests(dwc, dep);

	dep->stream_capable = false;
	dep->type = 0;
	dep->flags &= DWC3_EP_TXFIFO_RESIZED;

	return 0;
}

/* -------------------------------------------------------------------------- */

static int dwc3_gadget_ep0_enable(struct usb_ep *ep,
		const struct usb_endpoint_descriptor *desc)
{
	return -EINVAL;
}

static int dwc3_gadget_ep0_disable(struct usb_ep *ep)
{
	return -EINVAL;
}

/* -------------------------------------------------------------------------- */

static int dwc3_gadget_ep_enable(struct usb_ep *ep,
		const struct usb_endpoint_descriptor *desc)
{
	struct dwc3_ep			*dep;
	struct dwc3			*dwc;
	unsigned long			flags;
	int				ret;

	if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT) {
		pr_debug("dwc3: invalid parameters\n");
		return -EINVAL;
	}

	if (!desc->wMaxPacketSize) {
		pr_debug("dwc3: missing wMaxPacketSize\n");
		return -EINVAL;
	}

	dep = to_dwc3_ep(ep);
	dwc = dep->dwc;

	if (dev_WARN_ONCE(dwc->dev, dep->flags & DWC3_EP_ENABLED,
					"%s is already enabled\n",
					dep->name))
		return 0;

	spin_lock_irqsave(&dwc->lock, flags);
	ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_INIT);
	spin_unlock_irqrestore(&dwc->lock, flags);

	return ret;
}

static int dwc3_gadget_ep_disable(struct usb_ep *ep)
{
	struct dwc3_ep			*dep;
	struct dwc3			*dwc;
	unsigned long			flags;
	int				ret;

	if (!ep) {
		pr_debug("dwc3: invalid parameters\n");
		return -EINVAL;
	}

	dep = to_dwc3_ep(ep);
	dwc = dep->dwc;

	if (dev_WARN_ONCE(dwc->dev, !(dep->flags & DWC3_EP_ENABLED),
					"%s is already disabled\n",
					dep->name))
		return 0;

	spin_lock_irqsave(&dwc->lock, flags);
	ret = __dwc3_gadget_ep_disable(dep);
	spin_unlock_irqrestore(&dwc->lock, flags);

	return ret;
}

static struct usb_request *dwc3_gadget_ep_alloc_request(struct usb_ep *ep,
		gfp_t gfp_flags)
{
	struct dwc3_request		*req;
	struct dwc3_ep			*dep = to_dwc3_ep(ep);

	req = kzalloc(sizeof(*req), gfp_flags);
	if (!req)
		return NULL;

	req->direction	= dep->direction;
	req->epnum	= dep->number;
	req->dep	= dep;
	req->status	= DWC3_REQUEST_STATUS_UNKNOWN;

	trace_dwc3_alloc_request(req);

	return &req->request;
}

static void dwc3_gadget_ep_free_request(struct usb_ep *ep,
		struct usb_request *request)
{
	struct dwc3_request		*req = to_dwc3_request(request);

	trace_dwc3_free_request(req);
	kfree(req);
}

/**
 * dwc3_ep_prev_trb - returns the previous TRB in the ring
 * @dep: The endpoint with the TRB ring
 * @index: The index of the current TRB in the ring
 *
 * Returns the TRB prior to the one pointed to by the index. If the
 * index is 0, we will wrap backwards, skip the link TRB, and return
 * the one just before that.
 */
static struct dwc3_trb *dwc3_ep_prev_trb(struct dwc3_ep *dep, u8 index)
{
	u8 tmp = index;

	if (!tmp)
		tmp = DWC3_TRB_NUM - 1;

	return &dep->trb_pool[tmp - 1];
}

static u32 dwc3_calc_trbs_left(struct dwc3_ep *dep)
{
	u8			trbs_left;

	/*
	 * If the enqueue & dequeue are equal then the TRB ring is either full
	 * or empty. It's considered full when there are DWC3_TRB_NUM-1 of TRBs
	 * pending to be processed by the driver.
	 */
	if (dep->trb_enqueue == dep->trb_dequeue) {
		/*
		 * If there is any request remained in the started_list at
		 * this point, that means there is no TRB available.
		 */
		if (!list_empty(&dep->started_list))
			return 0;

		return DWC3_TRB_NUM - 1;
	}

	trbs_left = dep->trb_dequeue - dep->trb_enqueue;
	trbs_left &= (DWC3_TRB_NUM - 1);

	if (dep->trb_dequeue < dep->trb_enqueue)
		trbs_left--;

	return trbs_left;
}

/**
 * dwc3_prepare_one_trb - setup one TRB from one request
 * @dep: endpoint for which this request is prepared
 * @req: dwc3_request pointer
 * @trb_length: buffer size of the TRB
 * @chain: should this TRB be chained to the next?
 * @node: only for isochronous endpoints. First TRB needs different type.
 * @use_bounce_buffer: set to use bounce buffer
 * @must_interrupt: set to interrupt on TRB completion
 */
static void dwc3_prepare_one_trb(struct dwc3_ep *dep,
		struct dwc3_request *req, unsigned int trb_length,
		unsigned int chain, unsigned int node, bool use_bounce_buffer,
		bool must_interrupt)
{
	struct dwc3_trb		*trb;
	dma_addr_t		dma;
	unsigned int		stream_id = req->request.stream_id;
	unsigned int		short_not_ok = req->request.short_not_ok;
	unsigned int		no_interrupt = req->request.no_interrupt;
	unsigned int		is_last = req->request.is_last;
	struct dwc3		*dwc = dep->dwc;
	struct usb_gadget	*gadget = dwc->gadget;
	enum usb_device_speed	speed = gadget->speed;

	if (use_bounce_buffer)
		dma = dep->dwc->bounce_addr;
	else if (req->request.num_sgs > 0)
		dma = sg_dma_address(req->start_sg);
	else
		dma = req->request.dma;

	trb = &dep->trb_pool[dep->trb_enqueue];

	if (!req->trb) {
		dwc3_gadget_move_started_request(req);
		req->trb = trb;
		req->trb_dma = dwc3_trb_dma_offset(dep, trb);
	}

	req->num_trbs++;

	trb->size = DWC3_TRB_SIZE_LENGTH(trb_length);
	trb->bpl = lower_32_bits(dma);
	trb->bph = upper_32_bits(dma);

	switch (usb_endpoint_type(dep->endpoint.desc)) {
	case USB_ENDPOINT_XFER_CONTROL:
		trb->ctrl = DWC3_TRBCTL_CONTROL_SETUP;
		break;

	case USB_ENDPOINT_XFER_ISOC:
		if (!node) {
			trb->ctrl = DWC3_TRBCTL_ISOCHRONOUS_FIRST;

			/*
			 * USB Specification 2.0 Section 5.9.2 states that: "If
			 * there is only a single transaction in the microframe,
			 * only a DATA0 data packet PID is used.  If there are
			 * two transactions per microframe, DATA1 is used for
			 * the first transaction data packet and DATA0 is used
			 * for the second transaction data packet.  If there are
			 * three transactions per microframe, DATA2 is used for
			 * the first transaction data packet, DATA1 is used for
			 * the second, and DATA0 is used for the third."
			 *
			 * IOW, we should satisfy the following cases:
			 *
			 * 1) length <= maxpacket
			 *	- DATA0
			 *
			 * 2) maxpacket < length <= (2 * maxpacket)
			 *	- DATA1, DATA0
			 *
			 * 3) (2 * maxpacket) < length <= (3 * maxpacket)
			 *	- DATA2, DATA1, DATA0
			 */
			if (speed == USB_SPEED_HIGH) {
				struct usb_ep *ep = &dep->endpoint;
				unsigned int mult = 2;
				unsigned int maxp = usb_endpoint_maxp(ep->desc);

				if (req->request.length <= (2 * maxp))
					mult--;

				if (req->request.length <= maxp)
					mult--;

				trb->size |= DWC3_TRB_SIZE_PCM1(mult);
			}
		} else {
			trb->ctrl = DWC3_TRBCTL_ISOCHRONOUS;
		}

		/* always enable Interrupt on Missed ISOC */
		trb->ctrl |= DWC3_TRB_CTRL_ISP_IMI;
		break;

	case USB_ENDPOINT_XFER_BULK:
	case USB_ENDPOINT_XFER_INT:
		trb->ctrl = DWC3_TRBCTL_NORMAL;
		break;
	default:
		/*
		 * This is only possible with faulty memory because we
		 * checked it already :)
		 */
		dev_WARN(dwc->dev, "Unknown endpoint type %d\n",
				usb_endpoint_type(dep->endpoint.desc));
	}

	/*
	 * Enable Continue on Short Packet
	 * when endpoint is not a stream capable
	 */
	if (usb_endpoint_dir_out(dep->endpoint.desc)) {
		if (!dep->stream_capable)
			trb->ctrl |= DWC3_TRB_CTRL_CSP;

		if (short_not_ok)
			trb->ctrl |= DWC3_TRB_CTRL_ISP_IMI;
	}

	/* All TRBs setup for MST must set CSP=1 when LST=0 */
	if (dep->stream_capable && DWC3_MST_CAPABLE(&dwc->hwparams))
		trb->ctrl |= DWC3_TRB_CTRL_CSP;

	if ((!no_interrupt && !chain) || must_interrupt)
		trb->ctrl |= DWC3_TRB_CTRL_IOC;

	if (chain)
		trb->ctrl |= DWC3_TRB_CTRL_CHN;
	else if (dep->stream_capable && is_last &&
		 !DWC3_MST_CAPABLE(&dwc->hwparams))
		trb->ctrl |= DWC3_TRB_CTRL_LST;

	if (usb_endpoint_xfer_bulk(dep->endpoint.desc) && dep->stream_capable)
		trb->ctrl |= DWC3_TRB_CTRL_SID_SOFN(stream_id);

	/*
	 * As per data book 4.2.3.2TRB Control Bit Rules section
	 *
	 * The controller autonomously checks the HWO field of a TRB to determine if the
	 * entire TRB is valid. Therefore, software must ensure that the rest of the TRB
	 * is valid before setting the HWO field to '1'. In most systems, this means that
	 * software must update the fourth DWORD of a TRB last.
	 *
	 * However there is a possibility of CPU re-ordering here which can cause
	 * controller to observe the HWO bit set prematurely.
	 * Add a write memory barrier to prevent CPU re-ordering.
	 */
	wmb();
	trb->ctrl |= DWC3_TRB_CTRL_HWO;

	dwc3_ep_inc_enq(dep);

	trace_dwc3_prepare_trb(dep, trb);
}

static bool dwc3_needs_extra_trb(struct dwc3_ep *dep, struct dwc3_request *req)
{
	unsigned int maxp = usb_endpoint_maxp(dep->endpoint.desc);
	unsigned int rem = req->request.length % maxp;

	if ((req->request.length && req->request.zero && !rem &&
			!usb_endpoint_xfer_isoc(dep->endpoint.desc)) ||
			(!req->direction && rem))
		return true;

	return false;
}

/**
 * dwc3_prepare_last_sg - prepare TRBs for the last SG entry
 * @dep: The endpoint that the request belongs to
 * @req: The request to prepare
 * @entry_length: The last SG entry size
 * @node: Indicates whether this is not the first entry (for isoc only)
 *
 * Return the number of TRBs prepared.
 */
static int dwc3_prepare_last_sg(struct dwc3_ep *dep,
		struct dwc3_request *req, unsigned int entry_length,
		unsigned int node)
{
	unsigned int maxp = usb_endpoint_maxp(dep->endpoint.desc);
	unsigned int rem = req->request.length % maxp;
	unsigned int num_trbs = 1;

	if (dwc3_needs_extra_trb(dep, req))
		num_trbs++;

	if (dwc3_calc_trbs_left(dep) < num_trbs)
		return 0;

	req->needs_extra_trb = num_trbs > 1;

	/* Prepare a normal TRB */
	if (req->direction || req->request.length)
		dwc3_prepare_one_trb(dep, req, entry_length,
				req->needs_extra_trb, node, false, false);

	/* Prepare extra TRBs for ZLP and MPS OUT transfer alignment */
	if ((!req->direction && !req->request.length) || req->needs_extra_trb)
		dwc3_prepare_one_trb(dep, req,
				req->direction ? 0 : maxp - rem,
				false, 1, true, false);

	return num_trbs;
}

static int dwc3_prepare_trbs_sg(struct dwc3_ep *dep,
		struct dwc3_request *req)
{
	struct scatterlist *sg = req->start_sg;
	struct scatterlist *s;
	int		i;
	unsigned int length = req->request.length;
	unsigned int remaining = req->request.num_mapped_sgs
		- req->num_queued_sgs;
	unsigned int num_trbs = req->num_trbs;
	bool needs_extra_trb = dwc3_needs_extra_trb(dep, req);

	/*
	 * If we resume preparing the request, then get the remaining length of
	 * the request and resume where we left off.
	 */
	for_each_sg(req->request.sg, s, req->num_queued_sgs, i)
		length -= sg_dma_len(s);

	for_each_sg(sg, s, remaining, i) {
		unsigned int num_trbs_left = dwc3_calc_trbs_left(dep);
		unsigned int trb_length;
		bool must_interrupt = false;
		bool last_sg = false;

		trb_length = min_t(unsigned int, length, sg_dma_len(s));

		length -= trb_length;

		/*
		 * IOMMU driver is coalescing the list of sgs which shares a
		 * page boundary into one and giving it to USB driver. With
		 * this the number of sgs mapped is not equal to the number of
		 * sgs passed. So mark the chain bit to false if it isthe last
		 * mapped sg.
		 */
		if ((i == remaining - 1) || !length)
			last_sg = true;

		if (!num_trbs_left)
			break;

		if (last_sg) {
			if (!dwc3_prepare_last_sg(dep, req, trb_length, i))
				break;
		} else {
			/*
			 * Look ahead to check if we have enough TRBs for the
			 * next SG entry. If not, set interrupt on this TRB to
			 * resume preparing the next SG entry when more TRBs are
			 * free.
			 */
			if (num_trbs_left == 1 || (needs_extra_trb &&
					num_trbs_left <= 2 &&
					sg_dma_len(sg_next(s)) >= length))
				must_interrupt = true;

			dwc3_prepare_one_trb(dep, req, trb_length, 1, i, false,
					must_interrupt);
		}

		/*
		 * There can be a situation where all sgs in sglist are not
		 * queued because of insufficient trb number. To handle this
		 * case, update start_sg to next sg to be queued, so that
		 * we have free trbs we can continue queuing from where we
		 * previously stopped
		 */
		if (!last_sg)
			req->start_sg = sg_next(s);

		req->num_queued_sgs++;
		req->num_pending_sgs--;

		/*
		 * The number of pending SG entries may not correspond to the
		 * number of mapped SG entries. If all the data are queued, then
		 * don't include unused SG entries.
		 */
		if (length == 0) {
			req->num_pending_sgs = 0;
			break;
		}

		if (must_interrupt)
			break;
	}

	return req->num_trbs - num_trbs;
}

static int dwc3_prepare_trbs_linear(struct dwc3_ep *dep,
		struct dwc3_request *req)
{
	return dwc3_prepare_last_sg(dep, req, req->request.length, 0);
}

/*
 * dwc3_prepare_trbs - setup TRBs from requests
 * @dep: endpoint for which requests are being prepared
 *
 * The function goes through the requests list and sets up TRBs for the
 * transfers. The function returns once there are no more TRBs available or
 * it runs out of requests.
 *
 * Returns the number of TRBs prepared or negative errno.
 */
static int dwc3_prepare_trbs(struct dwc3_ep *dep)
{
	struct dwc3_request	*req, *n;
	int			ret = 0;

	BUILD_BUG_ON_NOT_POWER_OF_2(DWC3_TRB_NUM);

	/*
	 * We can get in a situation where there's a request in the started list
	 * but there weren't enough TRBs to fully kick it in the first time
	 * around, so it has been waiting for more TRBs to be freed up.
	 *
	 * In that case, we should check if we have a request with pending_sgs
	 * in the started list and prepare TRBs for that request first,
	 * otherwise we will prepare TRBs completely out of order and that will
	 * break things.
	 */
	list_for_each_entry(req, &dep->started_list, list) {
		if (req->num_pending_sgs > 0) {
			ret = dwc3_prepare_trbs_sg(dep, req);
			if (!ret || req->num_pending_sgs)
				return ret;
		}

		if (!dwc3_calc_trbs_left(dep))
			return ret;

		/*
		 * Don't prepare beyond a transfer. In DWC_usb32, its transfer
		 * burst capability may try to read and use TRBs beyond the
		 * active transfer instead of stopping.
		 */
		if (dep->stream_capable && req->request.is_last &&
		    !DWC3_MST_CAPABLE(&dep->dwc->hwparams))
			return ret;
	}

	list_for_each_entry_safe(req, n, &dep->pending_list, list) {
		struct dwc3	*dwc = dep->dwc;

		ret = usb_gadget_map_request_by_dev(dwc->sysdev, &req->request,
						    dep->direction);
		if (ret)
			return ret;

		req->sg			= req->request.sg;
		req->start_sg		= req->sg;
		req->num_queued_sgs	= 0;
		req->num_pending_sgs	= req->request.num_mapped_sgs;

		if (req->num_pending_sgs > 0) {
			ret = dwc3_prepare_trbs_sg(dep, req);
			if (req->num_pending_sgs)
				return ret;
		} else {
			ret = dwc3_prepare_trbs_linear(dep, req);
		}

		if (!ret || !dwc3_calc_trbs_left(dep))
			return ret;

		/*
		 * Don't prepare beyond a transfer. In DWC_usb32, its transfer
		 * burst capability may try to read and use TRBs beyond the
		 * active transfer instead of stopping.
		 */
		if (dep->stream_capable && req->request.is_last &&
		    !DWC3_MST_CAPABLE(&dwc->hwparams))
			return ret;
	}

	return ret;
}

static void dwc3_gadget_ep_cleanup_cancelled_requests(struct dwc3_ep *dep);

static int __dwc3_gadget_kick_transfer(struct dwc3_ep *dep)
{
	struct dwc3_gadget_ep_cmd_params params;
	struct dwc3_request		*req;
	int				starting;
	int				ret;
	u32				cmd;

	/*
	 * Note that it's normal to have no new TRBs prepared (i.e. ret == 0).
	 * This happens when we need to stop and restart a transfer such as in
	 * the case of reinitiating a stream or retrying an isoc transfer.
	 */
	ret = dwc3_prepare_trbs(dep);
	if (ret < 0)
		return ret;

	starting = !(dep->flags & DWC3_EP_TRANSFER_STARTED);

	/*
	 * If there's no new TRB prepared and we don't need to restart a
	 * transfer, there's no need to update the transfer.
	 */
	if (!ret && !starting)
		return ret;

	req = next_request(&dep->started_list);
	if (!req) {
		dep->flags |= DWC3_EP_PENDING_REQUEST;
		return 0;
	}

	memset(&params, 0, sizeof(params));

	if (starting) {
		params.param0 = upper_32_bits(req->trb_dma);
		params.param1 = lower_32_bits(req->trb_dma);
		cmd = DWC3_DEPCMD_STARTTRANSFER;

		if (dep->stream_capable)
			cmd |= DWC3_DEPCMD_PARAM(req->request.stream_id);

		if (usb_endpoint_xfer_isoc(dep->endpoint.desc))
			cmd |= DWC3_DEPCMD_PARAM(dep->frame_number);
	} else {
		cmd = DWC3_DEPCMD_UPDATETRANSFER |
			DWC3_DEPCMD_PARAM(dep->resource_index);
	}

	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
	if (ret < 0) {
		struct dwc3_request *tmp;

		if (ret == -EAGAIN)
			return ret;

		dwc3_stop_active_transfer(dep, true, true);

		list_for_each_entry_safe(req, tmp, &dep->started_list, list)
			dwc3_gadget_move_cancelled_request(req, DWC3_REQUEST_STATUS_DEQUEUED);

		/* If ep isn't started, then there's no end transfer pending */
		if (!(dep->flags & DWC3_EP_END_TRANSFER_PENDING))
			dwc3_gadget_ep_cleanup_cancelled_requests(dep);

		return ret;
	}

	if (dep->stream_capable && req->request.is_last &&
	    !DWC3_MST_CAPABLE(&dep->dwc->hwparams))
		dep->flags |= DWC3_EP_WAIT_TRANSFER_COMPLETE;

	return 0;
}

static int __dwc3_gadget_get_frame(struct dwc3 *dwc)
{
	u32			reg;

	reg = dwc3_readl(dwc->regs, DWC3_DSTS);
	return DWC3_DSTS_SOFFN(reg);
}

/**
 * __dwc3_stop_active_transfer - stop the current active transfer
 * @dep: isoc endpoint
 * @force: set forcerm bit in the command
 * @interrupt: command complete interrupt after End Transfer command
 *
 * When setting force, the ForceRM bit will be set. In that case
 * the controller won't update the TRB progress on command
 * completion. It also won't clear the HWO bit in the TRB.
 * The command will also not complete immediately in that case.
 */
static int __dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, bool interrupt)
{
	struct dwc3_gadget_ep_cmd_params params;
	u32 cmd;
	int ret;

	cmd = DWC3_DEPCMD_ENDTRANSFER;
	cmd |= force ? DWC3_DEPCMD_HIPRI_FORCERM : 0;
	cmd |= interrupt ? DWC3_DEPCMD_CMDIOC : 0;
	cmd |= DWC3_DEPCMD_PARAM(dep->resource_index);
	memset(&params, 0, sizeof(params));
	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
	WARN_ON_ONCE(ret);
	dep->resource_index = 0;

	if (!interrupt)
		dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
	else if (!ret)
		dep->flags |= DWC3_EP_END_TRANSFER_PENDING;

	return ret;
}

/**
 * dwc3_gadget_start_isoc_quirk - workaround invalid frame number
 * @dep: isoc endpoint
 *
 * This function tests for the correct combination of BIT[15:14] from the 16-bit
 * microframe number reported by the XferNotReady event for the future frame
 * number to start the isoc transfer.
 *
 * In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
 * isochronous IN, BIT[15:14] of the 16-bit microframe number reported by the
 * XferNotReady event are invalid. The driver uses this number to schedule the
 * isochronous transfer and passes it to the START TRANSFER command. Because
 * this number is invalid, the command may fail. If BIT[15:14] matches the
 * internal 16-bit microframe, the START TRANSFER command will pass and the
 * transfer will start at the scheduled time, if it is off by 1, the command
 * will still pass, but the transfer will start 2 seconds in the future. For all
 * other conditions, the START TRANSFER command will fail with bus-expiry.
 *
 * In order to workaround this issue, we can test for the correct combination of
 * BIT[15:14] by sending START TRANSFER commands with different values of
 * BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each combination is 2^14 uframe apart
 * (or 2 seconds). 4 seconds into the future will result in a bus-expiry status.
 * As the result, within the 4 possible combinations for BIT[15:14], there will
 * be 2 successful and 2 failure START COMMAND status. One of the 2 successful
 * command status will result in a 2-second delay start. The smaller BIT[15:14]
 * value is the correct combination.
 *
 * Since there are only 4 outcomes and the results are ordered, we can simply
 * test 2 START TRANSFER commands with BIT[15:14] combinations 'b00 and 'b01 to
 * deduce the smaller successful combination.
 *
 * Let test0 = test status for combination 'b00 and test1 = test status for 'b01
 * of BIT[15:14]. The correct combination is as follow:
 *
 * if test0 fails and test1 passes, BIT[15:14] is 'b01
 * if test0 fails and test1 fails, BIT[15:14] is 'b10
 * if test0 passes and test1 fails, BIT[15:14] is 'b11
 * if test0 passes and test1 passes, BIT[15:14] is 'b00
 *
 * Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
 * endpoints.
 */
static int dwc3_gadget_start_isoc_quirk(struct dwc3_ep *dep)
{
	int cmd_status = 0;
	bool test0;
	bool test1;

	while (dep->combo_num < 2) {
		struct dwc3_gadget_ep_cmd_params params;
		u32 test_frame_number;
		u32 cmd;

		/*
		 * Check if we can start isoc transfer on the next interval or
		 * 4 uframes in the future with BIT[15:14] as dep->combo_num
		 */
		test_frame_number = dep->frame_number & DWC3_FRNUMBER_MASK;
		test_frame_number |= dep->combo_num << 14;
		test_frame_number += max_t(u32, 4, dep->interval);

		params.param0 = upper_32_bits(dep->dwc->bounce_addr);
		params.param1 = lower_32_bits(dep->dwc->bounce_addr);

		cmd = DWC3_DEPCMD_STARTTRANSFER;
		cmd |= DWC3_DEPCMD_PARAM(test_frame_number);
		cmd_status = dwc3_send_gadget_ep_cmd(dep, cmd, &params);

		/* Redo if some other failure beside bus-expiry is received */
		if (cmd_status && cmd_status != -EAGAIN) {
			dep->start_cmd_status = 0;
			dep->combo_num = 0;
			return 0;
		}

		/* Store the first test status */
		if (dep->combo_num == 0)
			dep->start_cmd_status = cmd_status;

		dep->combo_num++;

		/*
		 * End the transfer if the START_TRANSFER command is successful
		 * to wait for the next XferNotReady to test the command again
		 */
		if (cmd_status == 0) {
			dwc3_stop_active_transfer(dep, true, true);
			return 0;
		}
	}

	/* test0 and test1 are both completed at this point */
	test0 = (dep->start_cmd_status == 0);
	test1 = (cmd_status == 0);

	if (!test0 && test1)
		dep->combo_num = 1;
	else if (!test0 && !test1)
		dep->combo_num = 2;
	else if (test0 && !test1)
		dep->combo_num = 3;
	else if (test0 && test1)
		dep->combo_num = 0;

	dep->frame_number &= DWC3_FRNUMBER_MASK;
	dep->frame_number |= dep->combo_num << 14;
	dep->frame_number += max_t(u32, 4, dep->interval);

	/* Reinitialize test variables */
	dep->start_cmd_status = 0;
	dep->combo_num = 0;

	return __dwc3_gadget_kick_transfer(dep);
}

static int __dwc3_gadget_start_isoc(struct dwc3_ep *dep)
{
	const struct usb_endpoint_descriptor *desc = dep->endpoint.desc;
	struct dwc3 *dwc = dep->dwc;
	int ret;
	int i;

	if (list_empty(&dep->pending_list) &&
	    list_empty(&dep->started_list)) {
		dep->flags |= DWC3_EP_PENDING_REQUEST;
		return -EAGAIN;
	}

	if (!dwc->dis_start_transfer_quirk &&
	    (DWC3_VER_IS_PRIOR(DWC31, 170A) ||
	     DWC3_VER_TYPE_IS_WITHIN(DWC31, 170A, EA01, EA06))) {
		if (dwc->gadget->speed <= USB_SPEED_HIGH && dep->direction)
			return dwc3_gadget_start_isoc_quirk(dep);
	}

	if (desc->bInterval <= 14 &&
	    dwc->gadget->speed >= USB_SPEED_HIGH) {
		u32 frame = __dwc3_gadget_get_frame(dwc);
		bool rollover = frame <
				(dep->frame_number & DWC3_FRNUMBER_MASK);

		/*
		 * frame_number is set from XferNotReady and may be already
		 * out of date. DSTS only provides the lower 14 bit of the
		 * current frame number. So add the upper two bits of
		 * frame_number and handle a possible rollover.
		 * This will provide the correct frame_number unless more than
		 * rollover has happened since XferNotReady.
		 */

		dep->frame_number = (dep->frame_number & ~DWC3_FRNUMBER_MASK) |
				     frame;
		if (rollover)
			dep->frame_number += BIT(14);
	}

	for (i = 0; i < DWC3_ISOC_MAX_RETRIES; i++) {
		int future_interval = i + 1;

		/* Give the controller at least 500us to schedule transfers */
		if (desc->bInterval < 3)
			future_interval += 3 - desc->bInterval;

		dep->frame_number = DWC3_ALIGN_FRAME(dep, future_interval);

		ret = __dwc3_gadget_kick_transfer(dep);
		if (ret != -EAGAIN)
			break;
	}

	/*
	 * After a number of unsuccessful start attempts due to bus-expiry
	 * status, issue END_TRANSFER command and retry on the next XferNotReady
	 * event.
	 */
	if (ret == -EAGAIN)
		ret = __dwc3_stop_active_transfer(dep, false, true);

	return ret;
}

static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
{
	struct dwc3		*dwc = dep->dwc;

	if (!dep->endpoint.desc || !dwc->pullups_connected || !dwc->connected) {
		dev_dbg(dwc->dev, "%s: can't queue to disabled endpoint\n",
				dep->name);
		return -ESHUTDOWN;
	}

	if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
				&req->request, req->dep->name))
		return -EINVAL;

	if (WARN(req->status < DWC3_REQUEST_STATUS_COMPLETED,
				"%s: request %pK already in flight\n",
				dep->name, &req->request))
		return -EINVAL;

	pm_runtime_get(dwc->dev);

	req->request.actual	= 0;
	req->request.status	= -EINPROGRESS;

	trace_dwc3_ep_queue(req);

	list_add_tail(&req->list, &dep->pending_list);
	req->status = DWC3_REQUEST_STATUS_QUEUED;

	if (dep->flags & DWC3_EP_WAIT_TRANSFER_COMPLETE)
		return 0;

	/*
	 * Start the transfer only after the END_TRANSFER is completed
	 * and endpoint STALL is cleared.
	 */
	if ((dep->flags & DWC3_EP_END_TRANSFER_PENDING) ||
	    (dep->flags & DWC3_EP_WEDGE) ||
	    (dep->flags & DWC3_EP_DELAY_STOP) ||
	    (dep->flags & DWC3_EP_STALL)) {
		dep->flags |= DWC3_EP_DELAY_START;
		return 0;
	}

	/*
	 * NOTICE: Isochronous endpoints should NEVER be prestarted. We must
	 * wait for a XferNotReady event so we will know what's the current
	 * (micro-)frame number.
	 *
	 * Without this trick, we are very, very likely gonna get Bus Expiry
	 * errors which will force us issue EndTransfer command.
	 */
	if (usb_endpoint_xfer_isoc(dep->endpoint.desc)) {
		if (!(dep->flags & DWC3_EP_TRANSFER_STARTED)) {
			if ((dep->flags & DWC3_EP_PENDING_REQUEST))
				return __dwc3_gadget_start_isoc(dep);

			return 0;
		}
	}

	__dwc3_gadget_kick_transfer(dep);

	return 0;
}

static int dwc3_gadget_ep_queue(struct usb_ep *ep, struct usb_request *request,
	gfp_t gfp_flags)
{
	struct dwc3_request		*req = to_dwc3_request(request);
	struct dwc3_ep			*dep = to_dwc3_ep(ep);
	struct dwc3			*dwc = dep->dwc;

	unsigned long			flags;

	int				ret;

	spin_lock_irqsave(&dwc->lock, flags);
	ret = __dwc3_gadget_ep_queue(dep, req);
	spin_unlock_irqrestore(&dwc->lock, flags);

	return ret;
}

static void dwc3_gadget_ep_skip_trbs(struct dwc3_ep *dep, struct dwc3_request *req)
{
	int i;

	/* If req->trb is not set, then the request has not started */
	if (!req->trb)
		return;

	/*
	 * If request was already started, this means we had to
	 * stop the transfer. With that we also need to ignore
	 * all TRBs used by the request, however TRBs can only
	 * be modified after completion of END_TRANSFER
	 * command. So what we do here is that we wait for
	 * END_TRANSFER completion and only after that, we jump
	 * over TRBs by clearing HWO and incrementing dequeue
	 * pointer.
	 */
	for (i = 0; i < req->num_trbs; i++) {
		struct dwc3_trb *trb;

		trb = &dep->trb_pool[dep->trb_dequeue];
		trb->ctrl &= ~DWC3_TRB_CTRL_HWO;
		dwc3_ep_inc_deq(dep);
	}

	req->num_trbs = 0;
}

static void dwc3_gadget_ep_cleanup_cancelled_requests(struct dwc3_ep *dep)
{
	struct dwc3_request		*req;
	struct dwc3			*dwc = dep->dwc;

	while (!list_empty(&dep->cancelled_list)) {
		req = next_request(&dep->cancelled_list);
		dwc3_gadget_ep_skip_trbs(dep, req);
		switch (req->status) {
		case DWC3_REQUEST_STATUS_DISCONNECTED:
			dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
			break;
		case DWC3_REQUEST_STATUS_DEQUEUED:
			dwc3_gadget_giveback(dep, req, -ECONNRESET);
			break;
		case DWC3_REQUEST_STATUS_STALLED:
			dwc3_gadget_giveback(dep, req, -EPIPE);
			break;
		default:
			dev_err(dwc->dev, "request cancelled with wrong reason:%d\n", req->status);
			dwc3_gadget_giveback(dep, req, -ECONNRESET);
			break;
		}
		/*
		 * The endpoint is disabled, let the dwc3_remove_requests()
		 * handle the cleanup.
		 */
		if (!dep->endpoint.desc)
			break;
	}
}

static int dwc3_gadget_ep_dequeue(struct usb_ep *ep,
		struct usb_request *request)
{
	struct dwc3_request		*req = to_dwc3_request(request);
	struct dwc3_request		*r = NULL;

	struct dwc3_ep			*dep = to_dwc3_ep(ep);
	struct dwc3			*dwc = dep->dwc;

	unsigned long			flags;
	int				ret = 0;

	trace_dwc3_ep_dequeue(req);

	spin_lock_irqsave(&dwc->lock, flags);

	list_for_each_entry(r, &dep->cancelled_list, list) {
		if (r == req)
			goto out;
	}

	list_for_each_entry(r, &dep->pending_list, list) {
		if (r == req) {
			dwc3_gadget_giveback(dep, req, -ECONNRESET);
			goto out;
		}
	}

	list_for_each_entry(r, &dep->started_list, list) {
		if (r == req) {
			struct dwc3_request *t;

			/* wait until it is processed */
			dwc3_stop_active_transfer(dep, true, true);

			/*
			 * Remove any started request if the transfer is
			 * cancelled.
			 */
			list_for_each_entry_safe(r, t, &dep->started_list, list)
				dwc3_gadget_move_cancelled_request(r,
						DWC3_REQUEST_STATUS_DEQUEUED);

			dep->flags &= ~DWC3_EP_WAIT_TRANSFER_COMPLETE;

			goto out;
		}
	}

	dev_err(dwc->dev, "request %pK was not queued to %s\n",
		request, ep->name);
	ret = -EINVAL;
out:
	spin_unlock_irqrestore(&dwc->lock, flags);

	return ret;
}

int __dwc3_gadget_ep_set_halt(struct dwc3_ep *dep, int value, int protocol)
{
	struct dwc3_gadget_ep_cmd_params	params;
	struct dwc3				*dwc = dep->dwc;
	struct dwc3_request			*req;
	struct dwc3_request			*tmp;
	int					ret;

	if (usb_endpoint_xfer_isoc(dep->endpoint.desc)) {
		dev_err(dwc->dev, "%s is of Isochronous type\n", dep->name);
		return -EINVAL;
	}

	memset(&params, 0x00, sizeof(params));

	if (value) {
		struct dwc3_trb *trb;

		unsigned int transfer_in_flight;
		unsigned int started;

		if (dep->number > 1)
			trb = dwc3_ep_prev_trb(dep, dep->trb_enqueue);
		else
			trb = &dwc->ep0_trb[dep->trb_enqueue];

		transfer_in_flight = trb->ctrl & DWC3_TRB_CTRL_HWO;
		started = !list_empty(&dep->started_list);

		if (!protocol && ((dep->direction && transfer_in_flight) ||
				(!dep->direction && started))) {
			return -EAGAIN;
		}

		ret = dwc3_send_gadget_ep_cmd(dep, DWC3_DEPCMD_SETSTALL,
				&params);
		if (ret)
			dev_err(dwc->dev, "failed to set STALL on %s\n",
					dep->name);
		else
			dep->flags |= DWC3_EP_STALL;
	} else {
		/*
		 * Don't issue CLEAR_STALL command to control endpoints. The
		 * controller automatically clears the STALL when it receives
		 * the SETUP token.
		 */
		if (dep->number <= 1) {
			dep->flags &= ~(DWC3_EP_STALL | DWC3_EP_WEDGE);
			return 0;
		}

		dwc3_stop_active_transfer(dep, true, true);

		list_for_each_entry_safe(req, tmp, &dep->started_list, list)
			dwc3_gadget_move_cancelled_request(req, DWC3_REQUEST_STATUS_STALLED);

		if (dep->flags & DWC3_EP_END_TRANSFER_PENDING ||
		    (dep->flags & DWC3_EP_DELAY_STOP)) {
			dep->flags |= DWC3_EP_PENDING_CLEAR_STALL;
			if (protocol)
				dwc->clear_stall_protocol = dep->number;

			return 0;
		}

		dwc3_gadget_ep_cleanup_cancelled_requests(dep);

		ret = dwc3_send_clear_stall_ep_cmd(dep);
		if (ret) {
			dev_err(dwc->dev, "failed to clear STALL on %s\n",
					dep->name);
			return ret;
		}

		dep->flags &= ~(DWC3_EP_STALL | DWC3_EP_WEDGE);

		if ((dep->flags & DWC3_EP_DELAY_START) &&
		    !usb_endpoint_xfer_isoc(dep->endpoint.desc))
			__dwc3_gadget_kick_transfer(dep);

		dep->flags &= ~DWC3_EP_DELAY_START;
	}

	return ret;
}

static int dwc3_gadget_ep_set_halt(struct usb_ep *ep, int value)
{
	struct dwc3_ep			*dep = to_dwc3_ep(ep);
	struct dwc3			*dwc = dep->dwc;

	unsigned long			flags;

	int				ret;

	spin_lock_irqsave(&dwc->lock, flags);
	ret = __dwc3_gadget_ep_set_halt(dep, value, false);
	spin_unlock_irqrestore(&dwc->lock, flags);

	return ret;
}

static int dwc3_gadget_ep_set_wedge(struct usb_ep *ep)
{
	struct dwc3_ep			*dep = to_dwc3_ep(ep);
	struct dwc3			*dwc = dep->dwc;
	unsigned long			flags;
	int				ret;

	spin_lock_irqsave(&dwc->lock, flags);
	dep->flags |= DWC3_EP_WEDGE;

	if (dep->number == 0 || dep->number == 1)
		ret = __dwc3_gadget_ep0_set_halt(ep, 1);
	else
		ret = __dwc3_gadget_ep_set_halt(dep, 1, false);
	spin_unlock_irqrestore(&dwc->lock, flags);

	return ret;
}

/* -------------------------------------------------------------------------- */

static struct usb_endpoint_descriptor dwc3_gadget_ep0_desc = {
	.bLength	= USB_DT_ENDPOINT_SIZE,
	.bDescriptorType = USB_DT_ENDPOINT,
	.bmAttributes	= USB_ENDPOINT_XFER_CONTROL,
};

static const struct usb_ep_ops dwc3_gadget_ep0_ops = {
	.enable		= dwc3_gadget_ep0_enable,
	.disable	= dwc3_gadget_ep0_disable,
	.alloc_request	= dwc3_gadget_ep_alloc_request,
	.free_request	= dwc3_gadget_ep_free_request,
	.queue		= dwc3_gadget_ep0_queue,
	.dequeue	= dwc3_gadget_ep_dequeue,
	.set_halt	= dwc3_gadget_ep0_set_halt,
	.set_wedge	= dwc3_gadget_ep_set_wedge,
};

static const struct usb_ep_ops dwc3_gadget_ep_ops = {
	.enable		= dwc3_gadget_ep_enable,
	.disable	= dwc3_gadget_ep_disable,
	.alloc_request	= dwc3_gadget_ep_alloc_request,
	.free_request	= dwc3_gadget_ep_free_request,
	.queue		= dwc3_gadget_ep_queue,
	.dequeue	= dwc3_gadget_ep_dequeue,
	.set_halt	= dwc3_gadget_ep_set_halt,
	.set_wedge	= dwc3_gadget_ep_set_wedge,
};

/* -------------------------------------------------------------------------- */

static int dwc3_gadget_get_frame(struct usb_gadget *g)
{
	struct dwc3		*dwc = gadget_to_dwc(g);

	return __dwc3_gadget_get_frame(dwc);
}

static int __dwc3_gadget_wakeup(struct dwc3 *dwc)
{
	int			retries;

	int			ret;
	u32			reg;

	u8			link_state;

	/*
	 * According to the Databook Remote wakeup request should
	 * be issued only when the device is in early suspend state.
	 *
	 * We can check that via USB Link State bits in DSTS register.
	 */
	reg = dwc3_readl(dwc->regs, DWC3_DSTS);

	link_state = DWC3_DSTS_USBLNKST(reg);

	switch (link_state) {
	case DWC3_LINK_STATE_RESET:
	case DWC3_LINK_STATE_RX_DET:	/* in HS, means Early Suspend */
	case DWC3_LINK_STATE_U3:	/* in HS, means SUSPEND */
	case DWC3_LINK_STATE_U2:	/* in HS, means Sleep (L1) */
	case DWC3_LINK_STATE_U1:
	case DWC3_LINK_STATE_RESUME:
		break;
	default:
		return -EINVAL;
	}

	ret = dwc3_gadget_set_link_state(dwc, DWC3_LINK_STATE_RECOV);
	if (ret < 0) {
		dev_err(dwc->dev, "failed to put link in Recovery\n");
		return ret;
	}

	/* Recent versions do this automatically */
	if (DWC3_VER_IS_PRIOR(DWC3, 194A)) {
		/* write zeroes to Link Change Request */
		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
		reg &= ~DWC3_DCTL_ULSTCHNGREQ_MASK;
		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
	}

	/* poll until Link State changes to ON */
	retries = 20000;

	while (retries--) {
		reg = dwc3_readl(dwc->regs, DWC3_DSTS);

		/* in HS, means ON */
		if (DWC3_DSTS_USBLNKST(reg) == DWC3_LINK_STATE_U0)
			break;
	}

	if (DWC3_DSTS_USBLNKST(reg) != DWC3_LINK_STATE_U0) {
		dev_err(dwc->dev, "failed to send remote wakeup\n");
		return -EINVAL;
	}

	return 0;
}

static int dwc3_gadget_wakeup(struct usb_gadget *g)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	unsigned long		flags;
	int			ret;

	spin_lock_irqsave(&dwc->lock, flags);
	ret = __dwc3_gadget_wakeup(dwc);
	spin_unlock_irqrestore(&dwc->lock, flags);

	return ret;
}

static int dwc3_gadget_set_selfpowered(struct usb_gadget *g,
		int is_selfpowered)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	unsigned long		flags;

	spin_lock_irqsave(&dwc->lock, flags);
	g->is_selfpowered = !!is_selfpowered;
	spin_unlock_irqrestore(&dwc->lock, flags);

	return 0;
}

static void dwc3_stop_active_transfers(struct dwc3 *dwc)
{
	u32 epnum;

	for (epnum = 2; epnum < dwc->num_eps; epnum++) {
		struct dwc3_ep *dep;

		dep = dwc->eps[epnum];
		if (!dep)
			continue;

		dwc3_remove_requests(dwc, dep);
	}
}

static void __dwc3_gadget_set_ssp_rate(struct dwc3 *dwc)
{
	enum usb_ssp_rate	ssp_rate = dwc->gadget_ssp_rate;
	u32			reg;

	if (ssp_rate == USB_SSP_GEN_UNKNOWN)
		ssp_rate = dwc->max_ssp_rate;

	reg = dwc3_readl(dwc->regs, DWC3_DCFG);
	reg &= ~DWC3_DCFG_SPEED_MASK;
	reg &= ~DWC3_DCFG_NUMLANES(~0);

	if (ssp_rate == USB_SSP_GEN_1x2)
		reg |= DWC3_DCFG_SUPERSPEED;
	else if (dwc->max_ssp_rate != USB_SSP_GEN_1x2)
		reg |= DWC3_DCFG_SUPERSPEED_PLUS;

	if (ssp_rate != USB_SSP_GEN_2x1 &&
	    dwc->max_ssp_rate != USB_SSP_GEN_2x1)
		reg |= DWC3_DCFG_NUMLANES(1);

	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
}

static void __dwc3_gadget_set_speed(struct dwc3 *dwc)
{
	enum usb_device_speed	speed;
	u32			reg;

	speed = dwc->gadget_max_speed;
	if (speed == USB_SPEED_UNKNOWN || speed > dwc->maximum_speed)
		speed = dwc->maximum_speed;

	if (speed == USB_SPEED_SUPER_PLUS &&
	    DWC3_IP_IS(DWC32)) {
		__dwc3_gadget_set_ssp_rate(dwc);
		return;
	}

	reg = dwc3_readl(dwc->regs, DWC3_DCFG);
	reg &= ~(DWC3_DCFG_SPEED_MASK);

	/*
	 * WORKAROUND: DWC3 revision < 2.20a have an issue
	 * which would cause metastability state on Run/Stop
	 * bit if we try to force the IP to USB2-only mode.
	 *
	 * Because of that, we cannot configure the IP to any
	 * speed other than the SuperSpeed
	 *
	 * Refers to:
	 *
	 * STAR#9000525659: Clock Domain Crossing on DCTL in
	 * USB 2.0 Mode
	 */
	if (DWC3_VER_IS_PRIOR(DWC3, 220A) &&
	    !dwc->dis_metastability_quirk) {
		reg |= DWC3_DCFG_SUPERSPEED;
	} else {
		switch (speed) {
		case USB_SPEED_FULL:
			reg |= DWC3_DCFG_FULLSPEED;
			break;
		case USB_SPEED_HIGH:
			reg |= DWC3_DCFG_HIGHSPEED;
			break;
		case USB_SPEED_SUPER:
			reg |= DWC3_DCFG_SUPERSPEED;
			break;
		case USB_SPEED_SUPER_PLUS:
			if (DWC3_IP_IS(DWC3))
				reg |= DWC3_DCFG_SUPERSPEED;
			else
				reg |= DWC3_DCFG_SUPERSPEED_PLUS;
			break;
		default:
			dev_err(dwc->dev, "invalid speed (%d)\n", speed);

			if (DWC3_IP_IS(DWC3))
				reg |= DWC3_DCFG_SUPERSPEED;
			else
				reg |= DWC3_DCFG_SUPERSPEED_PLUS;
		}
	}

	if (DWC3_IP_IS(DWC32) &&
	    speed > USB_SPEED_UNKNOWN &&
	    speed < USB_SPEED_SUPER_PLUS)
		reg &= ~DWC3_DCFG_NUMLANES(~0);

	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
}

static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)
{
	u32			reg;
	u32			timeout = 500;

	if (pm_runtime_suspended(dwc->dev))
		return 0;

	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
	if (is_on) {
		if (DWC3_VER_IS_WITHIN(DWC3, ANY, 187A)) {
			reg &= ~DWC3_DCTL_TRGTULST_MASK;
			reg |= DWC3_DCTL_TRGTULST_RX_DET;
		}

		if (!DWC3_VER_IS_PRIOR(DWC3, 194A))
			reg &= ~DWC3_DCTL_KEEP_CONNECT;
		reg |= DWC3_DCTL_RUN_STOP;

		if (dwc->has_hibernation)
			reg |= DWC3_DCTL_KEEP_CONNECT;

		__dwc3_gadget_set_speed(dwc);
		dwc->pullups_connected = true;
	} else {
		reg &= ~DWC3_DCTL_RUN_STOP;

		if (dwc->has_hibernation && !suspend)
			reg &= ~DWC3_DCTL_KEEP_CONNECT;

		dwc->pullups_connected = false;
	}

	dwc3_gadget_dctl_write_safe(dwc, reg);

	do {
		reg = dwc3_readl(dwc->regs, DWC3_DSTS);
		reg &= DWC3_DSTS_DEVCTRLHLT;
	} while (--timeout && !(!is_on ^ !reg));

	if (!timeout)
		return -ETIMEDOUT;

	return 0;
}

static void dwc3_gadget_disable_irq(struct dwc3 *dwc);
static void __dwc3_gadget_stop(struct dwc3 *dwc);
static int __dwc3_gadget_start(struct dwc3 *dwc);

static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
{
	unsigned long flags;

	spin_lock_irqsave(&dwc->lock, flags);
	dwc->connected = false;

	/*
	 * Per databook, when we want to stop the gadget, if a control transfer
	 * is still in process, complete it and get the core into setup phase.
	 */
	if (dwc->ep0state != EP0_SETUP_PHASE) {
		int ret;

		reinit_completion(&dwc->ep0_in_setup);

		spin_unlock_irqrestore(&dwc->lock, flags);
		ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
				msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
		spin_lock_irqsave(&dwc->lock, flags);
		if (ret == 0)
			dev_warn(dwc->dev, "timed out waiting for SETUP phase\n");
	}

	/*
	 * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a
	 * Section 4.1.8 Table 4-7, it states that for a device-initiated
	 * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
	 * command for any active transfers" before clearing the RunStop
	 * bit.
	 */
	dwc3_stop_active_transfers(dwc);
	__dwc3_gadget_stop(dwc);
	spin_unlock_irqrestore(&dwc->lock, flags);

	/*
	 * Note: if the GEVNTCOUNT indicates events in the event buffer, the
	 * driver needs to acknowledge them before the controller can halt.
	 * Simply let the interrupt handler acknowledges and handle the
	 * remaining event generated by the controller while polling for
	 * DSTS.DEVCTLHLT.
	 */
	return dwc3_gadget_run_stop(dwc, false, false);
}

static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	int			ret;

	is_on = !!is_on;

	dwc->softconnect = is_on;

	/*
	 * Avoid issuing a runtime resume if the device is already in the
	 * suspended state during gadget disconnect.  DWC3 gadget was already
	 * halted/stopped during runtime suspend.
	 */
	if (!is_on) {
		pm_runtime_barrier(dwc->dev);
		if (pm_runtime_suspended(dwc->dev))
			return 0;
	}

	/*
	 * Check the return value for successful resume, or error.  For a
	 * successful resume, the DWC3 runtime PM resume routine will handle
	 * the run stop sequence, so avoid duplicate operations here.
	 */
	ret = pm_runtime_get_sync(dwc->dev);
	if (!ret || ret < 0) {
		pm_runtime_put(dwc->dev);
		return 0;
	}

	if (dwc->pullups_connected == is_on) {
		pm_runtime_put(dwc->dev);
		return 0;
	}

	if (!is_on) {
		ret = dwc3_gadget_soft_disconnect(dwc);
	} else {
		/*
		 * In the Synopsys DWC_usb31 1.90a programming guide section
		 * 4.1.9, it specifies that for a reconnect after a
		 * device-initiated disconnect requires a core soft reset
		 * (DCTL.CSftRst) before enabling the run/stop bit.
		 */
		dwc3_core_soft_reset(dwc);

		dwc3_event_buffers_setup(dwc);
		__dwc3_gadget_start(dwc);
		ret = dwc3_gadget_run_stop(dwc, true, false);
	}

	pm_runtime_put(dwc->dev);

	return ret;
}

static void dwc3_gadget_enable_irq(struct dwc3 *dwc)
{
	u32			reg;

	/* Enable all but Start and End of Frame IRQs */
	reg = (DWC3_DEVTEN_EVNTOVERFLOWEN |
			DWC3_DEVTEN_CMDCMPLTEN |
			DWC3_DEVTEN_ERRTICERREN |
			DWC3_DEVTEN_WKUPEVTEN |
			DWC3_DEVTEN_CONNECTDONEEN |
			DWC3_DEVTEN_USBRSTEN |
			DWC3_DEVTEN_DISCONNEVTEN);

	if (DWC3_VER_IS_PRIOR(DWC3, 250A))
		reg |= DWC3_DEVTEN_ULSTCNGEN;

	/* On 2.30a and above this bit enables U3/L2-L1 Suspend Events */
	if (!DWC3_VER_IS_PRIOR(DWC3, 230A))
		reg |= DWC3_DEVTEN_U3L2L1SUSPEN;

	dwc3_writel(dwc->regs, DWC3_DEVTEN, reg);
}

static void dwc3_gadget_disable_irq(struct dwc3 *dwc)
{
	/* mask all interrupts */
	dwc3_writel(dwc->regs, DWC3_DEVTEN, 0x00);
}

static irqreturn_t dwc3_interrupt(int irq, void *_dwc);
static irqreturn_t dwc3_thread_interrupt(int irq, void *_dwc);

/**
 * dwc3_gadget_setup_nump - calculate and initialize NUMP field of %DWC3_DCFG
 * @dwc: pointer to our context structure
 *
 * The following looks like complex but it's actually very simple. In order to
 * calculate the number of packets we can burst at once on OUT transfers, we're
 * gonna use RxFIFO size.
 *
 * To calculate RxFIFO size we need two numbers:
 * MDWIDTH = size, in bits, of the internal memory bus
 * RAM2_DEPTH = depth, in MDWIDTH, of internal RAM2 (where RxFIFO sits)
 *
 * Given these two numbers, the formula is simple:
 *
 * RxFIFO Size = (RAM2_DEPTH * MDWIDTH / 8) - 24 - 16;
 *
 * 24 bytes is for 3x SETUP packets
 * 16 bytes is a clock domain crossing tolerance
 *
 * Given RxFIFO Size, NUMP = RxFIFOSize / 1024;
 */
static void dwc3_gadget_setup_nump(struct dwc3 *dwc)
{
	u32 ram2_depth;
	u32 mdwidth;
	u32 nump;
	u32 reg;

	ram2_depth = DWC3_GHWPARAMS7_RAM2_DEPTH(dwc->hwparams.hwparams7);
	mdwidth = dwc3_mdwidth(dwc);

	nump = ((ram2_depth * mdwidth / 8) - 24 - 16) / 1024;
	nump = min_t(u32, nump, 16);

	/* update NumP */
	reg = dwc3_readl(dwc->regs, DWC3_DCFG);
	reg &= ~DWC3_DCFG_NUMP_MASK;
	reg |= nump << DWC3_DCFG_NUMP_SHIFT;
	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
}

static int __dwc3_gadget_start(struct dwc3 *dwc)
{
	struct dwc3_ep		*dep;
	int			ret = 0;
	u32			reg;

	/*
	 * Use IMOD if enabled via dwc->imod_interval. Otherwise, if
	 * the core supports IMOD, disable it.
	 */
	if (dwc->imod_interval) {
		dwc3_writel(dwc->regs, DWC3_DEV_IMOD(0), dwc->imod_interval);
		dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), DWC3_GEVNTCOUNT_EHB);
	} else if (dwc3_has_imod(dwc)) {
		dwc3_writel(dwc->regs, DWC3_DEV_IMOD(0), 0);
	}

	/*
	 * We are telling dwc3 that we want to use DCFG.NUMP as ACK TP's NUMP
	 * field instead of letting dwc3 itself calculate that automatically.
	 *
	 * This way, we maximize the chances that we'll be able to get several
	 * bursts of data without going through any sort of endpoint throttling.
	 */
	reg = dwc3_readl(dwc->regs, DWC3_GRXTHRCFG);
	if (DWC3_IP_IS(DWC3))
		reg &= ~DWC3_GRXTHRCFG_PKTCNTSEL;
	else
		reg &= ~DWC31_GRXTHRCFG_PKTCNTSEL;

	dwc3_writel(dwc->regs, DWC3_GRXTHRCFG, reg);

	dwc3_gadget_setup_nump(dwc);

	/*
	 * Currently the controller handles single stream only. So, Ignore
	 * Packet Pending bit for stream selection and don't search for another
	 * stream if the host sends Data Packet with PP=0 (for OUT direction) or
	 * ACK with NumP=0 and PP=0 (for IN direction). This slightly improves
	 * the stream performance.
	 */
	reg = dwc3_readl(dwc->regs, DWC3_DCFG);
	reg |= DWC3_DCFG_IGNSTRMPP;
	dwc3_writel(dwc->regs, DWC3_DCFG, reg);

	/* Enable MST by default if the device is capable of MST */
	if (DWC3_MST_CAPABLE(&dwc->hwparams)) {
		reg = dwc3_readl(dwc->regs, DWC3_DCFG1);
		reg &= ~DWC3_DCFG1_DIS_MST_ENH;
		dwc3_writel(dwc->regs, DWC3_DCFG1, reg);
	}

	/* Start with SuperSpeed Default */
	dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);

	dep = dwc->eps[0];
	ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_INIT);
	if (ret) {
		dev_err(dwc->dev, "failed to enable %s\n", dep->name);
		goto err0;
	}

	dep = dwc->eps[1];
	ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_INIT);
	if (ret) {
		dev_err(dwc->dev, "failed to enable %s\n", dep->name);
		goto err1;
	}

	/* begin to receive SETUP packets */
	dwc->ep0state = EP0_SETUP_PHASE;
	dwc->ep0_bounced = false;
	dwc->link_state = DWC3_LINK_STATE_SS_DIS;
	dwc->delayed_status = false;
	dwc3_ep0_out_start(dwc);

	dwc3_gadget_enable_irq(dwc);

	return 0;

err1:
	__dwc3_gadget_ep_disable(dwc->eps[0]);

err0:
	return ret;
}

static int dwc3_gadget_start(struct usb_gadget *g,
		struct usb_gadget_driver *driver)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	unsigned long		flags;
	int			ret;
	int			irq;

	irq = dwc->irq_gadget;
	ret = request_threaded_irq(irq, dwc3_interrupt, dwc3_thread_interrupt,
			IRQF_SHARED, "dwc3", dwc->ev_buf);
	if (ret) {
		dev_err(dwc->dev, "failed to request irq #%d --> %d\n",
				irq, ret);
		return ret;
	}

	spin_lock_irqsave(&dwc->lock, flags);
	dwc->gadget_driver	= driver;
	spin_unlock_irqrestore(&dwc->lock, flags);

	return 0;
}

static void __dwc3_gadget_stop(struct dwc3 *dwc)
{
	dwc3_gadget_disable_irq(dwc);
	__dwc3_gadget_ep_disable(dwc->eps[0]);
	__dwc3_gadget_ep_disable(dwc->eps[1]);
}

static int dwc3_gadget_stop(struct usb_gadget *g)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	unsigned long		flags;

	spin_lock_irqsave(&dwc->lock, flags);
	dwc->gadget_driver	= NULL;
	dwc->max_cfg_eps = 0;
	spin_unlock_irqrestore(&dwc->lock, flags);

	free_irq(dwc->irq_gadget, dwc->ev_buf);

	return 0;
}

static void dwc3_gadget_config_params(struct usb_gadget *g,
				      struct usb_dcd_config_params *params)
{
	struct dwc3		*dwc = gadget_to_dwc(g);

	params->besl_baseline = USB_DEFAULT_BESL_UNSPECIFIED;
	params->besl_deep = USB_DEFAULT_BESL_UNSPECIFIED;

	/* Recommended BESL */
	if (!dwc->dis_enblslpm_quirk) {
		/*
		 * If the recommended BESL baseline is 0 or if the BESL deep is
		 * less than 2, Microsoft's Windows 10 host usb stack will issue
		 * a usb reset immediately after it receives the extended BOS
		 * descriptor and the enumeration will fail. To maintain
		 * compatibility with the Windows' usb stack, let's set the
		 * recommended BESL baseline to 1 and clamp the BESL deep to be
		 * within 2 to 15.
		 */
		params->besl_baseline = 1;
		if (dwc->is_utmi_l1_suspend)
			params->besl_deep =
				clamp_t(u8, dwc->hird_threshold, 2, 15);
	}

	/* U1 Device exit Latency */
	if (dwc->dis_u1_entry_quirk)
		params->bU1devExitLat = 0;
	else
		params->bU1devExitLat = DWC3_DEFAULT_U1_DEV_EXIT_LAT;

	/* U2 Device exit Latency */
	if (dwc->dis_u2_entry_quirk)
		params->bU2DevExitLat = 0;
	else
		params->bU2DevExitLat =
				cpu_to_le16(DWC3_DEFAULT_U2_DEV_EXIT_LAT);
}

static void dwc3_gadget_set_speed(struct usb_gadget *g,
				  enum usb_device_speed speed)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	unsigned long		flags;

	spin_lock_irqsave(&dwc->lock, flags);
	dwc->gadget_max_speed = speed;
	spin_unlock_irqrestore(&dwc->lock, flags);
}

static void dwc3_gadget_set_ssp_rate(struct usb_gadget *g,
				     enum usb_ssp_rate rate)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	unsigned long		flags;

	spin_lock_irqsave(&dwc->lock, flags);
	dwc->gadget_max_speed = USB_SPEED_SUPER_PLUS;
	dwc->gadget_ssp_rate = rate;
	spin_unlock_irqrestore(&dwc->lock, flags);
}

static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	union power_supply_propval	val = {0};
	int				ret;

	if (dwc->usb2_phy)
		return usb_phy_set_power(dwc->usb2_phy, mA);

	if (!dwc->usb_psy)
		return -EOPNOTSUPP;

	val.intval = 1000 * mA;
	ret = power_supply_set_property(dwc->usb_psy, POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT, &val);

	return ret;
}

/**
 * dwc3_gadget_check_config - ensure dwc3 can support the USB configuration
 * @g: pointer to the USB gadget
 *
 * Used to record the maximum number of endpoints being used in a USB composite
 * device. (across all configurations)  This is to be used in the calculation
 * of the TXFIFO sizes when resizing internal memory for individual endpoints.
 * It will help ensured that the resizing logic reserves enough space for at
 * least one max packet.
 */
static int dwc3_gadget_check_config(struct usb_gadget *g)
{
	struct dwc3 *dwc = gadget_to_dwc(g);
	struct usb_ep *ep;
	int fifo_size = 0;
	int ram1_depth;
	int ep_num = 0;

	if (!dwc->do_fifo_resize)
		return 0;

	list_for_each_entry(ep, &g->ep_list, ep_list) {
		/* Only interested in the IN endpoints */
		if (ep->claimed && (ep->address & USB_DIR_IN))
			ep_num++;
	}

	if (ep_num <= dwc->max_cfg_eps)
		return 0;

	/* Update the max number of eps in the composition */
	dwc->max_cfg_eps = ep_num;

	fifo_size = dwc3_gadget_calc_tx_fifo_size(dwc, dwc->max_cfg_eps);
	/* Based on the equation, increment by one for every ep */
	fifo_size += dwc->max_cfg_eps;

	/* Check if we can fit a single fifo per endpoint */
	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
	if (fifo_size > ram1_depth)
		return -ENOMEM;

	return 0;
}

static void dwc3_gadget_async_callbacks(struct usb_gadget *g, bool enable)
{
	struct dwc3		*dwc = gadget_to_dwc(g);
	unsigned long		flags;

	spin_lock_irqsave(&dwc->lock, flags);
	dwc->async_callbacks = enable;
	spin_unlock_irqrestore(&dwc->lock, flags);
}

static const struct usb_gadget_ops dwc3_gadget_ops = {
	.get_frame		= dwc3_gadget_get_frame,
	.wakeup			= dwc3_gadget_wakeup,
	.set_selfpowered	= dwc3_gadget_set_selfpowered,
	.pullup			= dwc3_gadget_pullup,
	.udc_start		= dwc3_gadget_start,
	.udc_stop		= dwc3_gadget_stop,
	.udc_set_speed		= dwc3_gadget_set_speed,
	.udc_set_ssp_rate	= dwc3_gadget_set_ssp_rate,
	.get_config_params	= dwc3_gadget_config_params,
	.vbus_draw		= dwc3_gadget_vbus_draw,
	.check_config		= dwc3_gadget_check_config,
	.udc_async_callbacks	= dwc3_gadget_async_callbacks,
};

/* -------------------------------------------------------------------------- */

static int dwc3_gadget_init_control_endpoint(struct dwc3_ep *dep)
{
	struct dwc3 *dwc = dep->dwc;

	usb_ep_set_maxpacket_limit(&dep->endpoint, 512);
	dep->endpoint.maxburst = 1;
	dep->endpoint.ops = &dwc3_gadget_ep0_ops;
	if (!dep->direction)
		dwc->gadget->ep0 = &dep->endpoint;

	dep->endpoint.caps.type_control = true;

	return 0;
}

static int dwc3_gadget_init_in_endpoint(struct dwc3_ep *dep)
{
	struct dwc3 *dwc = dep->dwc;
	u32 mdwidth;
	int size;
	int maxpacket;

	mdwidth = dwc3_mdwidth(dwc);

	/* MDWIDTH is represented in bits, we need it in bytes */
	mdwidth /= 8;

	size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1));
	if (DWC3_IP_IS(DWC3))
		size = DWC3_GTXFIFOSIZ_TXFDEP(size);
	else
		size = DWC31_GTXFIFOSIZ_TXFDEP(size);

	/*
	 * maxpacket size is determined as part of the following, after assuming
	 * a mult value of one maxpacket:
	 * DWC3 revision 280A and prior:
	 * fifo_size = mult * (max_packet / mdwidth) + 1;
	 * maxpacket = mdwidth * (fifo_size - 1);
	 *
	 * DWC3 revision 290A and onwards:
	 * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
	 * maxpacket = mdwidth * ((fifo_size - 1) - 1) - mdwidth;
	 */
	if (DWC3_VER_IS_PRIOR(DWC3, 290A))
		maxpacket = mdwidth * (size - 1);
	else
		maxpacket = mdwidth * ((size - 1) - 1) - mdwidth;

	/* Functionally, space for one max packet is sufficient */
	size = min_t(int, maxpacket, 1024);
	usb_ep_set_maxpacket_limit(&dep->endpoint, size);

	dep->endpoint.max_streams = 16;
	dep->endpoint.ops = &dwc3_gadget_ep_ops;
	list_add_tail(&dep->endpoint.ep_list,
			&dwc->gadget->ep_list);
	dep->endpoint.caps.type_iso = true;
	dep->endpoint.caps.type_bulk = true;
	dep->endpoint.caps.type_int = true;

	return dwc3_alloc_trb_pool(dep);
}

static int dwc3_gadget_init_out_endpoint(struct dwc3_ep *dep)
{
	struct dwc3 *dwc = dep->dwc;
	u32 mdwidth;
	int size;

	mdwidth = dwc3_mdwidth(dwc);

	/* MDWIDTH is represented in bits, convert to bytes */
	mdwidth /= 8;

	/* All OUT endpoints share a single RxFIFO space */
	size = dwc3_readl(dwc->regs, DWC3_GRXFIFOSIZ(0));
	if (DWC3_IP_IS(DWC3))
		size = DWC3_GRXFIFOSIZ_RXFDEP(size);
	else
		size = DWC31_GRXFIFOSIZ_RXFDEP(size);

	/* FIFO depth is in MDWDITH bytes */
	size *= mdwidth;

	/*
	 * To meet performance requirement, a minimum recommended RxFIFO size
	 * is defined as follow:
	 * RxFIFO size >= (3 x MaxPacketSize) +
	 * (3 x 8 bytes setup packets size) + (16 bytes clock crossing margin)
	 *
	 * Then calculate the max packet limit as below.
	 */
	size -= (3 * 8) + 16;
	if (size < 0)
		size = 0;
	else
		size /= 3;

	usb_ep_set_maxpacket_limit(&dep->endpoint, size);
	dep->endpoint.max_streams = 16;
	dep->endpoint.ops = &dwc3_gadget_ep_ops;
	list_add_tail(&dep->endpoint.ep_list,
			&dwc->gadget->ep_list);
	dep->endpoint.caps.type_iso = true;
	dep->endpoint.caps.type_bulk = true;
	dep->endpoint.caps.type_int = true;

	return dwc3_alloc_trb_pool(dep);
}

static int dwc3_gadget_init_endpoint(struct dwc3 *dwc, u8 epnum)
{
	struct dwc3_ep			*dep;
	bool				direction = epnum & 1;
	int				ret;
	u8				num = epnum >> 1;

	dep = kzalloc(sizeof(*dep), GFP_KERNEL);
	if (!dep)
		return -ENOMEM;

	dep->dwc = dwc;
	dep->number = epnum;
	dep->direction = direction;
	dep->regs = dwc->regs + DWC3_DEP_BASE(epnum);
	dwc->eps[epnum] = dep;
	dep->combo_num = 0;
	dep->start_cmd_status = 0;

	snprintf(dep->name, sizeof(dep->name), "ep%u%s", num,
			direction ? "in" : "out");

	dep->endpoint.name = dep->name;

	if (!(dep->number > 1)) {
		dep->endpoint.desc = &dwc3_gadget_ep0_desc;
		dep->endpoint.comp_desc = NULL;
	}

	if (num == 0)
		ret = dwc3_gadget_init_control_endpoint(dep);
	else if (direction)
		ret = dwc3_gadget_init_in_endpoint(dep);
	else
		ret = dwc3_gadget_init_out_endpoint(dep);

	if (ret)
		return ret;

	dep->endpoint.caps.dir_in = direction;
	dep->endpoint.caps.dir_out = !direction;

	INIT_LIST_HEAD(&dep->pending_list);
	INIT_LIST_HEAD(&dep->started_list);
	INIT_LIST_HEAD(&dep->cancelled_list);

	dwc3_debugfs_create_endpoint_dir(dep);

	return 0;
}

static int dwc3_gadget_init_endpoints(struct dwc3 *dwc, u8 total)
{
	u8				epnum;

	INIT_LIST_HEAD(&dwc->gadget->ep_list);

	for (epnum = 0; epnum < total; epnum++) {
		int			ret;

		ret = dwc3_gadget_init_endpoint(dwc, epnum);
		if (ret)
			return ret;
	}

	return 0;
}

static void dwc3_gadget_free_endpoints(struct dwc3 *dwc)
{
	struct dwc3_ep			*dep;
	u8				epnum;

	for (epnum = 0; epnum < DWC3_ENDPOINTS_NUM; epnum++) {
		dep = dwc->eps[epnum];
		if (!dep)
			continue;
		/*
		 * Physical endpoints 0 and 1 are special; they form the
		 * bi-directional USB endpoint 0.
		 *
		 * For those two physical endpoints, we don't allocate a TRB
		 * pool nor do we add them the endpoints list. Due to that, we
		 * shouldn't do these two operations otherwise we would end up
		 * with all sorts of bugs when removing dwc3.ko.
		 */
		if (epnum != 0 && epnum != 1) {
			dwc3_free_trb_pool(dep);
			list_del(&dep->endpoint.ep_list);
		}

		debugfs_remove_recursive(debugfs_lookup(dep->name,
				debugfs_lookup(dev_name(dep->dwc->dev),
					       usb_debug_root)));
		kfree(dep);
	}
}

/* -------------------------------------------------------------------------- */

static int dwc3_gadget_ep_reclaim_completed_trb(struct dwc3_ep *dep,
		struct dwc3_request *req, struct dwc3_trb *trb,
		const struct dwc3_event_depevt *event, int status, int chain)
{
	unsigned int		count;

	dwc3_ep_inc_deq(dep);

	trace_dwc3_complete_trb(dep, trb);
	req->num_trbs--;

	/*
	 * If we're in the middle of series of chained TRBs and we
	 * receive a short transfer along the way, DWC3 will skip
	 * through all TRBs including the last TRB in the chain (the
	 * where CHN bit is zero. DWC3 will also avoid clearing HWO
	 * bit and SW has to do it manually.
	 *
	 * We're going to do that here to avoid problems of HW trying
	 * to use bogus TRBs for transfers.
	 */
	if (chain && (trb->ctrl & DWC3_TRB_CTRL_HWO))
		trb->ctrl &= ~DWC3_TRB_CTRL_HWO;

	/*
	 * For isochronous transfers, the first TRB in a service interval must
	 * have the Isoc-First type. Track and report its interval frame number.
	 */
	if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
	    (trb->ctrl & DWC3_TRBCTL_ISOCHRONOUS_FIRST)) {
		unsigned int frame_number;

		frame_number = DWC3_TRB_CTRL_GET_SID_SOFN(trb->ctrl);
		frame_number &= ~(dep->interval - 1);
		req->request.frame_number = frame_number;
	}

	/*
	 * We use bounce buffer for requests that needs extra TRB or OUT ZLP. If
	 * this TRB points to the bounce buffer address, it's a MPS alignment
	 * TRB. Don't add it to req->remaining calculation.
	 */
	if (trb->bpl == lower_32_bits(dep->dwc->bounce_addr) &&
	    trb->bph == upper_32_bits(dep->dwc->bounce_addr)) {
		trb->ctrl &= ~DWC3_TRB_CTRL_HWO;
		return 1;
	}

	count = trb->size & DWC3_TRB_SIZE_MASK;
	req->remaining += count;

	if ((trb->ctrl & DWC3_TRB_CTRL_HWO) && status != -ESHUTDOWN)
		return 1;

	if (event->status & DEPEVT_STATUS_SHORT && !chain)
		return 1;

	if ((trb->ctrl & DWC3_TRB_CTRL_IOC) ||
	    (trb->ctrl & DWC3_TRB_CTRL_LST))
		return 1;

	return 0;
}

static int dwc3_gadget_ep_reclaim_trb_sg(struct dwc3_ep *dep,
		struct dwc3_request *req, const struct dwc3_event_depevt *event,
		int status)
{
	struct dwc3_trb *trb = &dep->trb_pool[dep->trb_dequeue];
	struct scatterlist *sg = req->sg;
	struct scatterlist *s;
	unsigned int num_queued = req->num_queued_sgs;
	unsigned int i;
	int ret = 0;

	for_each_sg(sg, s, num_queued, i) {
		trb = &dep->trb_pool[dep->trb_dequeue];

		req->sg = sg_next(s);
		req->num_queued_sgs--;

		ret = dwc3_gadget_ep_reclaim_completed_trb(dep, req,
				trb, event, status, true);
		if (ret)
			break;
	}

	return ret;
}

static int dwc3_gadget_ep_reclaim_trb_linear(struct dwc3_ep *dep,
		struct dwc3_request *req, const struct dwc3_event_depevt *event,
		int status)
{
	struct dwc3_trb *trb = &dep->trb_pool[dep->trb_dequeue];

	return dwc3_gadget_ep_reclaim_completed_trb(dep, req, trb,
			event, status, false);
}

static bool dwc3_gadget_ep_request_completed(struct dwc3_request *req)
{
	return req->num_pending_sgs == 0 && req->num_queued_sgs == 0;
}

static int dwc3_gadget_ep_cleanup_completed_request(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event,
		struct dwc3_request *req, int status)
{
	int request_status;
	int ret;

	if (req->request.num_mapped_sgs)
		ret = dwc3_gadget_ep_reclaim_trb_sg(dep, req, event,
				status);
	else
		ret = dwc3_gadget_ep_reclaim_trb_linear(dep, req, event,
				status);

	req->request.actual = req->request.length - req->remaining;

	if (!dwc3_gadget_ep_request_completed(req))
		goto out;

	if (req->needs_extra_trb) {
		ret = dwc3_gadget_ep_reclaim_trb_linear(dep, req, event,
				status);
		req->needs_extra_trb = false;
	}

	/*
	 * The event status only reflects the status of the TRB with IOC set.
	 * For the requests that don't set interrupt on completion, the driver
	 * needs to check and return the status of the completed TRBs associated
	 * with the request. Use the status of the last TRB of the request.
	 */
	if (req->request.no_interrupt) {
		struct dwc3_trb *trb;

		trb = dwc3_ep_prev_trb(dep, dep->trb_dequeue);
		switch (DWC3_TRB_SIZE_TRBSTS(trb->size)) {
		case DWC3_TRBSTS_MISSED_ISOC:
			/* Isoc endpoint only */
			request_status = -EXDEV;
			break;
		case DWC3_TRB_STS_XFER_IN_PROG:
			/* Applicable when End Transfer with ForceRM=0 */
		case DWC3_TRBSTS_SETUP_PENDING:
			/* Control endpoint only */
		case DWC3_TRBSTS_OK:
		default:
			request_status = 0;
			break;
		}
	} else {
		request_status = status;
	}

	dwc3_gadget_giveback(dep, req, request_status);

out:
	return ret;
}

static void dwc3_gadget_ep_cleanup_completed_requests(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event, int status)
{
	struct dwc3_request	*req;

	while (!list_empty(&dep->started_list)) {
		int ret;

		req = next_request(&dep->started_list);
		ret = dwc3_gadget_ep_cleanup_completed_request(dep, event,
				req, status);
		if (ret)
			break;
		/*
		 * The endpoint is disabled, let the dwc3_remove_requests()
		 * handle the cleanup.
		 */
		if (!dep->endpoint.desc)
			break;
	}
}

static bool dwc3_gadget_ep_should_continue(struct dwc3_ep *dep)
{
	struct dwc3_request	*req;
	struct dwc3		*dwc = dep->dwc;

	if (!dep->endpoint.desc || !dwc->pullups_connected ||
	    !dwc->connected)
		return false;

	if (!list_empty(&dep->pending_list))
		return true;

	/*
	 * We only need to check the first entry of the started list. We can
	 * assume the completed requests are removed from the started list.
	 */
	req = next_request(&dep->started_list);
	if (!req)
		return false;

	return !dwc3_gadget_ep_request_completed(req);
}

static void dwc3_gadget_endpoint_frame_from_event(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event)
{
	dep->frame_number = event->parameters;
}

static bool dwc3_gadget_endpoint_trbs_complete(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event, int status)
{
	struct dwc3		*dwc = dep->dwc;
	bool			no_started_trb = true;

	dwc3_gadget_ep_cleanup_completed_requests(dep, event, status);

	if (dep->flags & DWC3_EP_END_TRANSFER_PENDING)
		goto out;

	if (!dep->endpoint.desc)
		return no_started_trb;

	if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
		list_empty(&dep->started_list) &&
		(list_empty(&dep->pending_list) || status == -EXDEV))
		dwc3_stop_active_transfer(dep, true, true);
	else if (dwc3_gadget_ep_should_continue(dep))
		if (__dwc3_gadget_kick_transfer(dep) == 0)
			no_started_trb = false;

out:
	/*
	 * WORKAROUND: This is the 2nd half of U1/U2 -> U0 workaround.
	 * See dwc3_gadget_linksts_change_interrupt() for 1st half.
	 */
	if (DWC3_VER_IS_PRIOR(DWC3, 183A)) {
		u32		reg;
		int		i;

		for (i = 0; i < DWC3_ENDPOINTS_NUM; i++) {
			dep = dwc->eps[i];

			if (!(dep->flags & DWC3_EP_ENABLED))
				continue;

			if (!list_empty(&dep->started_list))
				return no_started_trb;
		}

		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
		reg |= dwc->u1u2;
		dwc3_writel(dwc->regs, DWC3_DCTL, reg);

		dwc->u1u2 = 0;
	}

	return no_started_trb;
}

static void dwc3_gadget_endpoint_transfer_in_progress(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event)
{
	int status = 0;

	if (!dep->endpoint.desc)
		return;

	if (usb_endpoint_xfer_isoc(dep->endpoint.desc))
		dwc3_gadget_endpoint_frame_from_event(dep, event);

	if (event->status & DEPEVT_STATUS_BUSERR)
		status = -ECONNRESET;

	if (event->status & DEPEVT_STATUS_MISSED_ISOC)
		status = -EXDEV;

	dwc3_gadget_endpoint_trbs_complete(dep, event, status);
}

static void dwc3_gadget_endpoint_transfer_complete(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event)
{
	int status = 0;

	dep->flags &= ~DWC3_EP_TRANSFER_STARTED;

	if (event->status & DEPEVT_STATUS_BUSERR)
		status = -ECONNRESET;

	if (dwc3_gadget_endpoint_trbs_complete(dep, event, status))
		dep->flags &= ~DWC3_EP_WAIT_TRANSFER_COMPLETE;
}

static void dwc3_gadget_endpoint_transfer_not_ready(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event)
{
	dwc3_gadget_endpoint_frame_from_event(dep, event);

	/*
	 * The XferNotReady event is generated only once before the endpoint
	 * starts. It will be generated again when END_TRANSFER command is
	 * issued. For some controller versions, the XferNotReady event may be
	 * generated while the END_TRANSFER command is still in process. Ignore
	 * it and wait for the next XferNotReady event after the command is
	 * completed.
	 */
	if (dep->flags & DWC3_EP_END_TRANSFER_PENDING)
		return;

	(void) __dwc3_gadget_start_isoc(dep);
}

static void dwc3_gadget_endpoint_command_complete(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event)
{
	u8 cmd = DEPEVT_PARAMETER_CMD(event->parameters);

	if (cmd != DWC3_DEPCMD_ENDTRANSFER)
		return;

	/*
	 * The END_TRANSFER command will cause the controller to generate a
	 * NoStream Event, and it's not due to the host DP NoStream rejection.
	 * Ignore the next NoStream event.
	 */
	if (dep->stream_capable)
		dep->flags |= DWC3_EP_IGNORE_NEXT_NOSTREAM;

	dep->flags &= ~DWC3_EP_END_TRANSFER_PENDING;
	dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
	dwc3_gadget_ep_cleanup_cancelled_requests(dep);

	if (dep->flags & DWC3_EP_PENDING_CLEAR_STALL) {
		struct dwc3 *dwc = dep->dwc;

		dep->flags &= ~DWC3_EP_PENDING_CLEAR_STALL;
		if (dwc3_send_clear_stall_ep_cmd(dep)) {
			struct usb_ep *ep0 = &dwc->eps[0]->endpoint;

			dev_err(dwc->dev, "failed to clear STALL on %s\n", dep->name);
			if (dwc->delayed_status)
				__dwc3_gadget_ep0_set_halt(ep0, 1);
			return;
		}

		dep->flags &= ~(DWC3_EP_STALL | DWC3_EP_WEDGE);
		if (dwc->clear_stall_protocol == dep->number)
			dwc3_ep0_send_delayed_status(dwc);
	}

	if ((dep->flags & DWC3_EP_DELAY_START) &&
	    !usb_endpoint_xfer_isoc(dep->endpoint.desc))
		__dwc3_gadget_kick_transfer(dep);

	dep->flags &= ~DWC3_EP_DELAY_START;
}

static void dwc3_gadget_endpoint_stream_event(struct dwc3_ep *dep,
		const struct dwc3_event_depevt *event)
{
	struct dwc3 *dwc = dep->dwc;

	if (event->status == DEPEVT_STREAMEVT_FOUND) {
		dep->flags |= DWC3_EP_FIRST_STREAM_PRIMED;
		goto out;
	}

	/* Note: NoStream rejection event param value is 0 and not 0xFFFF */
	switch (event->parameters) {
	case DEPEVT_STREAM_PRIME:
		/*
		 * If the host can properly transition the endpoint state from
		 * idle to prime after a NoStream rejection, there's no need to
		 * force restarting the endpoint to reinitiate the stream. To
		 * simplify the check, assume the host follows the USB spec if
		 * it primed the endpoint more than once.
		 */
		if (dep->flags & DWC3_EP_FORCE_RESTART_STREAM) {
			if (dep->flags & DWC3_EP_FIRST_STREAM_PRIMED)
				dep->flags &= ~DWC3_EP_FORCE_RESTART_STREAM;
			else
				dep->flags |= DWC3_EP_FIRST_STREAM_PRIMED;
		}

		break;
	case DEPEVT_STREAM_NOSTREAM:
		if ((dep->flags & DWC3_EP_IGNORE_NEXT_NOSTREAM) ||
		    !(dep->flags & DWC3_EP_FORCE_RESTART_STREAM) ||
		    (!DWC3_MST_CAPABLE(&dwc->hwparams) &&
		     !(dep->flags & DWC3_EP_WAIT_TRANSFER_COMPLETE)))
			break;

		/*
		 * If the host rejects a stream due to no active stream, by the
		 * USB and xHCI spec, the endpoint will be put back to idle
		 * state. When the host is ready (buffer added/updated), it will
		 * prime the endpoint to inform the usb device controller. This
		 * triggers the device controller to issue ERDY to restart the
		 * stream. However, some hosts don't follow this and keep the
		 * endpoint in the idle state. No prime will come despite host
		 * streams are updated, and the device controller will not be
		 * triggered to generate ERDY to move the next stream data. To
		 * workaround this and maintain compatibility with various
		 * hosts, force to reinitate the stream until the host is ready
		 * instead of waiting for the host to prime the endpoint.
		 */
		if (DWC3_VER_IS_WITHIN(DWC32, 100A, ANY)) {
			unsigned int cmd = DWC3_DGCMD_SET_ENDPOINT_PRIME;

			dwc3_send_gadget_generic_command(dwc, cmd, dep->number);
		} else {
			dep->flags |= DWC3_EP_DELAY_START;
			dwc3_stop_active_transfer(dep, true, true);
			return;
		}
		break;
	}

out:
	dep->flags &= ~DWC3_EP_IGNORE_NEXT_NOSTREAM;
}

static void dwc3_endpoint_interrupt(struct dwc3 *dwc,
		const struct dwc3_event_depevt *event)
{
	struct dwc3_ep		*dep;
	u8			epnum = event->endpoint_number;

	dep = dwc->eps[epnum];

	if (!(dep->flags & DWC3_EP_ENABLED)) {
		if (!(dep->flags & DWC3_EP_TRANSFER_STARTED))
			return;

		/* Handle only EPCMDCMPLT when EP disabled */
		if (event->endpoint_event != DWC3_DEPEVT_EPCMDCMPLT)
			return;
	}

	if (epnum == 0 || epnum == 1) {
		dwc3_ep0_interrupt(dwc, event);
		return;
	}

	switch (event->endpoint_event) {
	case DWC3_DEPEVT_XFERINPROGRESS:
		dwc3_gadget_endpoint_transfer_in_progress(dep, event);
		break;
	case DWC3_DEPEVT_XFERNOTREADY:
		dwc3_gadget_endpoint_transfer_not_ready(dep, event);
		break;
	case DWC3_DEPEVT_EPCMDCMPLT:
		dwc3_gadget_endpoint_command_complete(dep, event);
		break;
	case DWC3_DEPEVT_XFERCOMPLETE:
		dwc3_gadget_endpoint_transfer_complete(dep, event);
		break;
	case DWC3_DEPEVT_STREAMEVT:
		dwc3_gadget_endpoint_stream_event(dep, event);
		break;
	case DWC3_DEPEVT_RXTXFIFOEVT:
		break;
	}
}

static void dwc3_disconnect_gadget(struct dwc3 *dwc)
{
	if (dwc->async_callbacks && dwc->gadget_driver->disconnect) {
		spin_unlock(&dwc->lock);
		dwc->gadget_driver->disconnect(dwc->gadget);
		spin_lock(&dwc->lock);
	}
}

static void dwc3_suspend_gadget(struct dwc3 *dwc)
{
	if (dwc->async_callbacks && dwc->gadget_driver->suspend) {
		spin_unlock(&dwc->lock);
		dwc->gadget_driver->suspend(dwc->gadget);
		spin_lock(&dwc->lock);
	}
}

static void dwc3_resume_gadget(struct dwc3 *dwc)
{
	if (dwc->async_callbacks && dwc->gadget_driver->resume) {
		spin_unlock(&dwc->lock);
		dwc->gadget_driver->resume(dwc->gadget);
		spin_lock(&dwc->lock);
	}
}

static void dwc3_reset_gadget(struct dwc3 *dwc)
{
	if (!dwc->gadget_driver)
		return;

	if (dwc->async_callbacks && dwc->gadget->speed != USB_SPEED_UNKNOWN) {
		spin_unlock(&dwc->lock);
		usb_gadget_udc_reset(dwc->gadget, dwc->gadget_driver);
		spin_lock(&dwc->lock);
	}
}

void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
	bool interrupt)
{
	struct dwc3 *dwc = dep->dwc;

	/*
	 * Only issue End Transfer command to the control endpoint of a started
	 * Data Phase. Typically we should only do so in error cases such as
	 * invalid/unexpected direction as described in the control transfer
	 * flow of the programming guide.
	 */
	if (dep->number <= 1 && dwc->ep0state != EP0_DATA_PHASE)
		return;

	if (!(dep->flags & DWC3_EP_TRANSFER_STARTED) ||
	    (dep->flags & DWC3_EP_DELAY_STOP) ||
	    (dep->flags & DWC3_EP_END_TRANSFER_PENDING))
		return;

	/*
	 * If a Setup packet is received but yet to DMA out, the controller will
	 * not process the End Transfer command of any endpoint. Polling of its
	 * DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
	 * timeout. Delay issuing the End Transfer command until the Setup TRB is
	 * prepared.
	 */
	if (dwc->ep0state != EP0_SETUP_PHASE && !dwc->delayed_status) {
		dep->flags |= DWC3_EP_DELAY_STOP;
		return;
	}

	/*
	 * NOTICE: We are violating what the Databook says about the
	 * EndTransfer command. Ideally we would _always_ wait for the
	 * EndTransfer Command Completion IRQ, but that's causing too
	 * much trouble synchronizing between us and gadget driver.
	 *
	 * We have discussed this with the IP Provider and it was
	 * suggested to giveback all requests here.
	 *
	 * Note also that a similar handling was tested by Synopsys
	 * (thanks a lot Paul) and nothing bad has come out of it.
	 * In short, what we're doing is issuing EndTransfer with
	 * CMDIOC bit set and delay kicking transfer until the
	 * EndTransfer command had completed.
	 *
	 * As of IP version 3.10a of the DWC_usb3 IP, the controller
	 * supports a mode to work around the above limitation. The
	 * software can poll the CMDACT bit in the DEPCMD register
	 * after issuing a EndTransfer command. This mode is enabled
	 * by writing GUCTL2[14]. This polling is already done in the
	 * dwc3_send_gadget_ep_cmd() function so if the mode is
	 * enabled, the EndTransfer command will have completed upon
	 * returning from this function.
	 *
	 * This mode is NOT available on the DWC_usb31 IP.
	 */

	__dwc3_stop_active_transfer(dep, force, interrupt);
}

static void dwc3_clear_stall_all_ep(struct dwc3 *dwc)
{
	u32 epnum;

	for (epnum = 1; epnum < DWC3_ENDPOINTS_NUM; epnum++) {
		struct dwc3_ep *dep;
		int ret;

		dep = dwc->eps[epnum];
		if (!dep)
			continue;

		if (!(dep->flags & DWC3_EP_STALL))
			continue;

		dep->flags &= ~DWC3_EP_STALL;

		ret = dwc3_send_clear_stall_ep_cmd(dep);
		WARN_ON_ONCE(ret);
	}
}

static void dwc3_gadget_disconnect_interrupt(struct dwc3 *dwc)
{
	int			reg;

	dwc3_gadget_set_link_state(dwc, DWC3_LINK_STATE_RX_DET);

	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
	reg &= ~DWC3_DCTL_INITU1ENA;
	reg &= ~DWC3_DCTL_INITU2ENA;
	dwc3_gadget_dctl_write_safe(dwc, reg);

	dwc3_disconnect_gadget(dwc);

	dwc->gadget->speed = USB_SPEED_UNKNOWN;
	dwc->setup_packet_pending = false;
	usb_gadget_set_state(dwc->gadget, USB_STATE_NOTATTACHED);

	dwc->connected = false;
}

static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
{
	u32			reg;

	/*
	 * Ideally, dwc3_reset_gadget() would trigger the function
	 * drivers to stop any active transfers through ep disable.
	 * However, for functions which defer ep disable, such as mass
	 * storage, we will need to rely on the call to stop active
	 * transfers here, and avoid allowing of request queuing.
	 */
	dwc->connected = false;

	/*
	 * WORKAROUND: DWC3 revisions <1.88a have an issue which
	 * would cause a missing Disconnect Event if there's a
	 * pending Setup Packet in the FIFO.
	 *
	 * There's no suggested workaround on the official Bug
	 * report, which states that "unless the driver/application
	 * is doing any special handling of a disconnect event,
	 * there is no functional issue".
	 *
	 * Unfortunately, it turns out that we _do_ some special
	 * handling of a disconnect event, namely complete all
	 * pending transfers, notify gadget driver of the
	 * disconnection, and so on.
	 *
	 * Our suggested workaround is to follow the Disconnect
	 * Event steps here, instead, based on a setup_packet_pending
	 * flag. Such flag gets set whenever we have a SETUP_PENDING
	 * status for EP0 TRBs and gets cleared on XferComplete for the
	 * same endpoint.
	 *
	 * Refers to:
	 *
	 * STAR#9000466709: RTL: Device : Disconnect event not
	 * generated if setup packet pending in FIFO
	 */
	if (DWC3_VER_IS_PRIOR(DWC3, 188A)) {
		if (dwc->setup_packet_pending)
			dwc3_gadget_disconnect_interrupt(dwc);
	}

	dwc3_reset_gadget(dwc);

	/*
	 * From SNPS databook section 8.1.2, the EP0 should be in setup
	 * phase. So ensure that EP0 is in setup phase by issuing a stall
	 * and restart if EP0 is not in setup phase.
	 */
	if (dwc->ep0state != EP0_SETUP_PHASE) {
		unsigned int	dir;

		dir = !!dwc->ep0_expect_in;
		if (dwc->ep0state == EP0_DATA_PHASE)
			dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
		else
			dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);

		dwc->eps[0]->trb_enqueue = 0;
		dwc->eps[1]->trb_enqueue = 0;

		dwc3_ep0_stall_and_restart(dwc);
	}

	/*
	 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
	 * Section 4.1.2 Table 4-2, it states that during a USB reset, the SW
	 * needs to ensure that it sends "a DEPENDXFER command for any active
	 * transfers."
	 */
	dwc3_stop_active_transfers(dwc);
	dwc->connected = true;

	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
	reg &= ~DWC3_DCTL_TSTCTRL_MASK;
	dwc3_gadget_dctl_write_safe(dwc, reg);
	dwc->test_mode = false;
	dwc3_clear_stall_all_ep(dwc);

	/* Reset device address to zero */
	reg = dwc3_readl(dwc->regs, DWC3_DCFG);
	reg &= ~(DWC3_DCFG_DEVADDR_MASK);
	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
}

static void dwc3_gadget_conndone_interrupt(struct dwc3 *dwc)
{
	struct dwc3_ep		*dep;
	int			ret;
	u32			reg;
	u8			lanes = 1;
	u8			speed;

	reg = dwc3_readl(dwc->regs, DWC3_DSTS);
	speed = reg & DWC3_DSTS_CONNECTSPD;
	dwc->speed = speed;

	if (DWC3_IP_IS(DWC32))
		lanes = DWC3_DSTS_CONNLANES(reg) + 1;

	dwc->gadget->ssp_rate = USB_SSP_GEN_UNKNOWN;

	/*
	 * RAMClkSel is reset to 0 after USB reset, so it must be reprogrammed
	 * each time on Connect Done.
	 *
	 * Currently we always use the reset value. If any platform
	 * wants to set this to a different value, we need to add a
	 * setting and update GCTL.RAMCLKSEL here.
	 */

	switch (speed) {
	case DWC3_DSTS_SUPERSPEED_PLUS:
		dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
		dwc->gadget->ep0->maxpacket = 512;
		dwc->gadget->speed = USB_SPEED_SUPER_PLUS;

		if (lanes > 1)
			dwc->gadget->ssp_rate = USB_SSP_GEN_2x2;
		else
			dwc->gadget->ssp_rate = USB_SSP_GEN_2x1;
		break;
	case DWC3_DSTS_SUPERSPEED:
		/*
		 * WORKAROUND: DWC3 revisions <1.90a have an issue which
		 * would cause a missing USB3 Reset event.
		 *
		 * In such situations, we should force a USB3 Reset
		 * event by calling our dwc3_gadget_reset_interrupt()
		 * routine.
		 *
		 * Refers to:
		 *
		 * STAR#9000483510: RTL: SS : USB3 reset event may
		 * not be generated always when the link enters poll
		 */
		if (DWC3_VER_IS_PRIOR(DWC3, 190A))
			dwc3_gadget_reset_interrupt(dwc);

		dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
		dwc->gadget->ep0->maxpacket = 512;
		dwc->gadget->speed = USB_SPEED_SUPER;

		if (lanes > 1) {
			dwc->gadget->speed = USB_SPEED_SUPER_PLUS;
			dwc->gadget->ssp_rate = USB_SSP_GEN_1x2;
		}
		break;
	case DWC3_DSTS_HIGHSPEED:
		dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(64);
		dwc->gadget->ep0->maxpacket = 64;
		dwc->gadget->speed = USB_SPEED_HIGH;
		break;
	case DWC3_DSTS_FULLSPEED:
		dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(64);
		dwc->gadget->ep0->maxpacket = 64;
		dwc->gadget->speed = USB_SPEED_FULL;
		break;
	}

	dwc->eps[1]->endpoint.maxpacket = dwc->gadget->ep0->maxpacket;

	/* Enable USB2 LPM Capability */

	if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A) &&
	    !dwc->usb2_gadget_lpm_disable &&
	    (speed != DWC3_DSTS_SUPERSPEED) &&
	    (speed != DWC3_DSTS_SUPERSPEED_PLUS)) {
		reg = dwc3_readl(dwc->regs, DWC3_DCFG);
		reg |= DWC3_DCFG_LPM_CAP;
		dwc3_writel(dwc->regs, DWC3_DCFG, reg);

		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
		reg &= ~(DWC3_DCTL_HIRD_THRES_MASK | DWC3_DCTL_L1_HIBER_EN);

		reg |= DWC3_DCTL_HIRD_THRES(dwc->hird_threshold |
					    (dwc->is_utmi_l1_suspend << 4));

		/*
		 * When dwc3 revisions >= 2.40a, LPM Erratum is enabled and
		 * DCFG.LPMCap is set, core responses with an ACK and the
		 * BESL value in the LPM token is less than or equal to LPM
		 * NYET threshold.
		 */
		WARN_ONCE(DWC3_VER_IS_PRIOR(DWC3, 240A) && dwc->has_lpm_erratum,
				"LPM Erratum not available on dwc3 revisions < 2.40a\n");

		if (dwc->has_lpm_erratum && !DWC3_VER_IS_PRIOR(DWC3, 240A))
			reg |= DWC3_DCTL_NYET_THRES(dwc->lpm_nyet_threshold);

		dwc3_gadget_dctl_write_safe(dwc, reg);
	} else {
		if (dwc->usb2_gadget_lpm_disable) {
			reg = dwc3_readl(dwc->regs, DWC3_DCFG);
			reg &= ~DWC3_DCFG_LPM_CAP;
			dwc3_writel(dwc->regs, DWC3_DCFG, reg);
		}

		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
		reg &= ~DWC3_DCTL_HIRD_THRES_MASK;
		dwc3_gadget_dctl_write_safe(dwc, reg);
	}

	dep = dwc->eps[0];
	ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_MODIFY);
	if (ret) {
		dev_err(dwc->dev, "failed to enable %s\n", dep->name);
		return;
	}

	dep = dwc->eps[1];
	ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_MODIFY);
	if (ret) {
		dev_err(dwc->dev, "failed to enable %s\n", dep->name);
		return;
	}

	/*
	 * Configure PHY via GUSB3PIPECTLn if required.
	 *
	 * Update GTXFIFOSIZn
	 *
	 * In both cases reset values should be sufficient.
	 */
}

static void dwc3_gadget_wakeup_interrupt(struct dwc3 *dwc)
{
	/*
	 * TODO take core out of low power mode when that's
	 * implemented.
	 */

	if (dwc->async_callbacks && dwc->gadget_driver->resume) {
		spin_unlock(&dwc->lock);
		dwc->gadget_driver->resume(dwc->gadget);
		spin_lock(&dwc->lock);
	}
}

static void dwc3_gadget_linksts_change_interrupt(struct dwc3 *dwc,
		unsigned int evtinfo)
{
	enum dwc3_link_state	next = evtinfo & DWC3_LINK_STATE_MASK;
	unsigned int		pwropt;

	/*
	 * WORKAROUND: DWC3 < 2.50a have an issue when configured without
	 * Hibernation mode enabled which would show up when device detects
	 * host-initiated U3 exit.
	 *
	 * In that case, device will generate a Link State Change Interrupt
	 * from U3 to RESUME which is only necessary if Hibernation is
	 * configured in.
	 *
	 * There are no functional changes due to such spurious event and we
	 * just need to ignore it.
	 *
	 * Refers to:
	 *
	 * STAR#9000570034 RTL: SS Resume event generated in non-Hibernation
	 * operational mode
	 */
	pwropt = DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams1);
	if (DWC3_VER_IS_PRIOR(DWC3, 250A) &&
			(pwropt != DWC3_GHWPARAMS1_EN_PWROPT_HIB)) {
		if ((dwc->link_state == DWC3_LINK_STATE_U3) &&
				(next == DWC3_LINK_STATE_RESUME)) {
			return;
		}
	}

	/*
	 * WORKAROUND: DWC3 Revisions <1.83a have an issue which, depending
	 * on the link partner, the USB session might do multiple entry/exit
	 * of low power states before a transfer takes place.
	 *
	 * Due to this problem, we might experience lower throughput. The
	 * suggested workaround is to disable DCTL[12:9] bits if we're
	 * transitioning from U1/U2 to U0 and enable those bits again
	 * after a transfer completes and there are no pending transfers
	 * on any of the enabled endpoints.
	 *
	 * This is the first half of that workaround.
	 *
	 * Refers to:
	 *
	 * STAR#9000446952: RTL: Device SS : if U1/U2 ->U0 takes >128us
	 * core send LGO_Ux entering U0
	 */
	if (DWC3_VER_IS_PRIOR(DWC3, 183A)) {
		if (next == DWC3_LINK_STATE_U0) {
			u32	u1u2;
			u32	reg;

			switch (dwc->link_state) {
			case DWC3_LINK_STATE_U1:
			case DWC3_LINK_STATE_U2:
				reg = dwc3_readl(dwc->regs, DWC3_DCTL);
				u1u2 = reg & (DWC3_DCTL_INITU2ENA
						| DWC3_DCTL_ACCEPTU2ENA
						| DWC3_DCTL_INITU1ENA
						| DWC3_DCTL_ACCEPTU1ENA);

				if (!dwc->u1u2)
					dwc->u1u2 = reg & u1u2;

				reg &= ~u1u2;

				dwc3_gadget_dctl_write_safe(dwc, reg);
				break;
			default:
				/* do nothing */
				break;
			}
		}
	}

	switch (next) {
	case DWC3_LINK_STATE_U1:
		if (dwc->speed == USB_SPEED_SUPER)
			dwc3_suspend_gadget(dwc);
		break;
	case DWC3_LINK_STATE_U2:
	case DWC3_LINK_STATE_U3:
		dwc3_suspend_gadget(dwc);
		break;
	case DWC3_LINK_STATE_RESUME:
		dwc3_resume_gadget(dwc);
		break;
	default:
		/* do nothing */
		break;
	}

	dwc->link_state = next;
}

static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc,
					  unsigned int evtinfo)
{
	enum dwc3_link_state next = evtinfo & DWC3_LINK_STATE_MASK;

	if (dwc->link_state != next && next == DWC3_LINK_STATE_U3)
		dwc3_suspend_gadget(dwc);

	dwc->link_state = next;
}

static void dwc3_gadget_hibernation_interrupt(struct dwc3 *dwc,
		unsigned int evtinfo)
{
	unsigned int is_ss = evtinfo & BIT(4);

	/*
	 * WORKAROUND: DWC3 revison 2.20a with hibernation support
	 * have a known issue which can cause USB CV TD.9.23 to fail
	 * randomly.
	 *
	 * Because of this issue, core could generate bogus hibernation
	 * events which SW needs to ignore.
	 *
	 * Refers to:
	 *
	 * STAR#9000546576: Device Mode Hibernation: Issue in USB 2.0
	 * Device Fallback from SuperSpeed
	 */
	if (is_ss ^ (dwc->speed == USB_SPEED_SUPER))
		return;

	/* enter hibernation here */
}

static void dwc3_gadget_interrupt(struct dwc3 *dwc,
		const struct dwc3_event_devt *event)
{
	switch (event->type) {
	case DWC3_DEVICE_EVENT_DISCONNECT:
		dwc3_gadget_disconnect_interrupt(dwc);
		break;
	case DWC3_DEVICE_EVENT_RESET:
		dwc3_gadget_reset_interrupt(dwc);
		break;
	case DWC3_DEVICE_EVENT_CONNECT_DONE:
		dwc3_gadget_conndone_interrupt(dwc);
		break;
	case DWC3_DEVICE_EVENT_WAKEUP:
		dwc3_gadget_wakeup_interrupt(dwc);
		break;
	case DWC3_DEVICE_EVENT_HIBER_REQ:
		if (dev_WARN_ONCE(dwc->dev, !dwc->has_hibernation,
					"unexpected hibernation event\n"))
			break;

		dwc3_gadget_hibernation_interrupt(dwc, event->event_info);
		break;
	case DWC3_DEVICE_EVENT_LINK_STATUS_CHANGE:
		dwc3_gadget_linksts_change_interrupt(dwc, event->event_info);
		break;
	case DWC3_DEVICE_EVENT_SUSPEND:
		/* It changed to be suspend event for version 2.30a and above */
		if (!DWC3_VER_IS_PRIOR(DWC3, 230A)) {
			/*
			 * Ignore suspend event until the gadget enters into
			 * USB_STATE_CONFIGURED state.
			 */
			if (dwc->gadget->state >= USB_STATE_CONFIGURED)
				dwc3_gadget_suspend_interrupt(dwc,
						event->event_info);
		}
		break;
	case DWC3_DEVICE_EVENT_SOF:
	case DWC3_DEVICE_EVENT_ERRATIC_ERROR:
	case DWC3_DEVICE_EVENT_CMD_CMPL:
	case DWC3_DEVICE_EVENT_OVERFLOW:
		break;
	default:
		dev_WARN(dwc->dev, "UNKNOWN IRQ %d\n", event->type);
	}
}

static void dwc3_process_event_entry(struct dwc3 *dwc,
		const union dwc3_event *event)
{
	trace_dwc3_event(event->raw, dwc);

	if (!event->type.is_devspec)
		dwc3_endpoint_interrupt(dwc, &event->depevt);
	else if (event->type.type == DWC3_EVENT_TYPE_DEV)
		dwc3_gadget_interrupt(dwc, &event->devt);
	else
		dev_err(dwc->dev, "UNKNOWN IRQ type %d\n", event->raw);
}

static irqreturn_t dwc3_process_event_buf(struct dwc3_event_buffer *evt)
{
	struct dwc3 *dwc = evt->dwc;
	irqreturn_t ret = IRQ_NONE;
	int left;

	left = evt->count;

	if (!(evt->flags & DWC3_EVENT_PENDING))
		return IRQ_NONE;

	while (left > 0) {
		union dwc3_event event;

		event.raw = *(u32 *) (evt->cache + evt->lpos);

		dwc3_process_event_entry(dwc, &event);

		/*
		 * FIXME we wrap around correctly to the next entry as
		 * almost all entries are 4 bytes in size. There is one
		 * entry which has 12 bytes which is a regular entry
		 * followed by 8 bytes data. ATM I don't know how
		 * things are organized if we get next to the a
		 * boundary so I worry about that once we try to handle
		 * that.
		 */
		evt->lpos = (evt->lpos + 4) % evt->length;
		left -= 4;
	}

	evt->count = 0;
	ret = IRQ_HANDLED;

	/* Unmask interrupt */
	dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0),
		    DWC3_GEVNTSIZ_SIZE(evt->length));

	if (dwc->imod_interval) {
		dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), DWC3_GEVNTCOUNT_EHB);
		dwc3_writel(dwc->regs, DWC3_DEV_IMOD(0), dwc->imod_interval);
	}

	/* Keep the clearing of DWC3_EVENT_PENDING at the end */
	evt->flags &= ~DWC3_EVENT_PENDING;

	return ret;
}

static irqreturn_t dwc3_thread_interrupt(int irq, void *_evt)
{
	struct dwc3_event_buffer *evt = _evt;
	struct dwc3 *dwc = evt->dwc;
	unsigned long flags;
	irqreturn_t ret = IRQ_NONE;

	local_bh_disable();
	spin_lock_irqsave(&dwc->lock, flags);
	ret = dwc3_process_event_buf(evt);
	spin_unlock_irqrestore(&dwc->lock, flags);
	local_bh_enable();

	return ret;
}

static irqreturn_t dwc3_check_event_buf(struct dwc3_event_buffer *evt)
{
	struct dwc3 *dwc = evt->dwc;
	u32 amount;
	u32 count;

	if (pm_runtime_suspended(dwc->dev)) {
		pm_runtime_get(dwc->dev);
		disable_irq_nosync(dwc->irq_gadget);
		dwc->pending_events = true;
		return IRQ_HANDLED;
	}

	/*
	 * With PCIe legacy interrupt, test shows that top-half irq handler can
	 * be called again after HW interrupt deassertion. Check if bottom-half
	 * irq event handler completes before caching new event to prevent
	 * losing events.
	 */
	if (evt->flags & DWC3_EVENT_PENDING)
		return IRQ_HANDLED;

	count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
	count &= DWC3_GEVNTCOUNT_MASK;
	if (!count)
		return IRQ_NONE;

	evt->count = count;
	evt->flags |= DWC3_EVENT_PENDING;

	/* Mask interrupt */
	dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0),
		    DWC3_GEVNTSIZ_INTMASK | DWC3_GEVNTSIZ_SIZE(evt->length));

	amount = min(count, evt->length - evt->lpos);
	memcpy(evt->cache + evt->lpos, evt->buf + evt->lpos, amount);

	if (amount < count)
		memcpy(evt->cache, evt->buf, count - amount);

	dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);

	return IRQ_WAKE_THREAD;
}

static irqreturn_t dwc3_interrupt(int irq, void *_evt)
{
	struct dwc3_event_buffer	*evt = _evt;

	return dwc3_check_event_buf(evt);
}

static int dwc3_gadget_get_irq(struct dwc3 *dwc)
{
	struct platform_device *dwc3_pdev = to_platform_device(dwc->dev);
	int irq;

	irq = platform_get_irq_byname_optional(dwc3_pdev, "peripheral");
	if (irq > 0)
		goto out;

	if (irq == -EPROBE_DEFER)
		goto out;

	irq = platform_get_irq_byname_optional(dwc3_pdev, "dwc_usb3");
	if (irq > 0)
		goto out;

	if (irq == -EPROBE_DEFER)
		goto out;

	irq = platform_get_irq(dwc3_pdev, 0);
	if (irq > 0)
		goto out;

	if (!irq)
		irq = -EINVAL;

out:
	return irq;
}

static void dwc_gadget_release(struct device *dev)
{
	struct usb_gadget *gadget = container_of(dev, struct usb_gadget, dev);

	kfree(gadget);
}

/**
 * dwc3_gadget_init - initializes gadget related registers
 * @dwc: pointer to our controller context structure
 *
 * Returns 0 on success otherwise negative errno.
 */
int dwc3_gadget_init(struct dwc3 *dwc)
{
	int ret;
	int irq;
	struct device *dev;

	irq = dwc3_gadget_get_irq(dwc);
	if (irq < 0) {
		ret = irq;
		goto err0;
	}

	dwc->irq_gadget = irq;

	dwc->ep0_trb = dma_alloc_coherent(dwc->sysdev,
					  sizeof(*dwc->ep0_trb) * 2,
					  &dwc->ep0_trb_addr, GFP_KERNEL);
	if (!dwc->ep0_trb) {
		dev_err(dwc->dev, "failed to allocate ep0 trb\n");
		ret = -ENOMEM;
		goto err0;
	}

	dwc->setup_buf = kzalloc(DWC3_EP0_SETUP_SIZE, GFP_KERNEL);
	if (!dwc->setup_buf) {
		ret = -ENOMEM;
		goto err1;
	}

	dwc->bounce = dma_alloc_coherent(dwc->sysdev, DWC3_BOUNCE_SIZE,
			&dwc->bounce_addr, GFP_KERNEL);
	if (!dwc->bounce) {
		ret = -ENOMEM;
		goto err2;
	}

	init_completion(&dwc->ep0_in_setup);
	dwc->gadget = kzalloc(sizeof(struct usb_gadget), GFP_KERNEL);
	if (!dwc->gadget) {
		ret = -ENOMEM;
		goto err3;
	}


	usb_initialize_gadget(dwc->dev, dwc->gadget, dwc_gadget_release);
	dev				= &dwc->gadget->dev;
	dev->platform_data		= dwc;
	dwc->gadget->ops		= &dwc3_gadget_ops;
	dwc->gadget->speed		= USB_SPEED_UNKNOWN;
	dwc->gadget->ssp_rate		= USB_SSP_GEN_UNKNOWN;
	dwc->gadget->sg_supported	= true;
	dwc->gadget->name		= "dwc3-gadget";
	dwc->gadget->lpm_capable	= !dwc->usb2_gadget_lpm_disable;

	/*
	 * FIXME We might be setting max_speed to <SUPER, however versions
	 * <2.20a of dwc3 have an issue with metastability (documented
	 * elsewhere in this driver) which tells us we can't set max speed to
	 * anything lower than SUPER.
	 *
	 * Because gadget.max_speed is only used by composite.c and function
	 * drivers (i.e. it won't go into dwc3's registers) we are allowing this
	 * to happen so we avoid sending SuperSpeed Capability descriptor
	 * together with our BOS descriptor as that could confuse host into
	 * thinking we can handle super speed.
	 *
	 * Note that, in fact, we won't even support GetBOS requests when speed
	 * is less than super speed because we don't have means, yet, to tell
	 * composite.c that we are USB 2.0 + LPM ECN.
	 */
	if (DWC3_VER_IS_PRIOR(DWC3, 220A) &&
	    !dwc->dis_metastability_quirk)
		dev_info(dwc->dev, "changing max_speed on rev %08x\n",
				dwc->revision);

	dwc->gadget->max_speed		= dwc->maximum_speed;
	dwc->gadget->max_ssp_rate	= dwc->max_ssp_rate;

	/*
	 * REVISIT: Here we should clear all pending IRQs to be
	 * sure we're starting from a well known location.
	 */

	ret = dwc3_gadget_init_endpoints(dwc, dwc->num_eps);
	if (ret)
		goto err4;

	ret = usb_add_gadget(dwc->gadget);
	if (ret) {
		dev_err(dwc->dev, "failed to add gadget\n");
		goto err5;
	}

	if (DWC3_IP_IS(DWC32) && dwc->maximum_speed == USB_SPEED_SUPER_PLUS)
		dwc3_gadget_set_ssp_rate(dwc->gadget, dwc->max_ssp_rate);
	else
		dwc3_gadget_set_speed(dwc->gadget, dwc->maximum_speed);

	return 0;

err5:
	dwc3_gadget_free_endpoints(dwc);
err4:
	usb_put_gadget(dwc->gadget);
	dwc->gadget = NULL;
err3:
	dma_free_coherent(dwc->sysdev, DWC3_BOUNCE_SIZE, dwc->bounce,
			dwc->bounce_addr);

err2:
	kfree(dwc->setup_buf);

err1:
	dma_free_coherent(dwc->sysdev, sizeof(*dwc->ep0_trb) * 2,
			dwc->ep0_trb, dwc->ep0_trb_addr);

err0:
	return ret;
}

/* -------------------------------------------------------------------------- */

void dwc3_gadget_exit(struct dwc3 *dwc)
{
	if (!dwc->gadget)
		return;

	usb_del_gadget(dwc->gadget);
	dwc3_gadget_free_endpoints(dwc);
	usb_put_gadget(dwc->gadget);
	dma_free_coherent(dwc->sysdev, DWC3_BOUNCE_SIZE, dwc->bounce,
			  dwc->bounce_addr);
	kfree(dwc->setup_buf);
	dma_free_coherent(dwc->sysdev, sizeof(*dwc->ep0_trb) * 2,
			  dwc->ep0_trb, dwc->ep0_trb_addr);
}

int dwc3_gadget_suspend(struct dwc3 *dwc)
{
	if (!dwc->gadget_driver)
		return 0;

	dwc3_gadget_run_stop(dwc, false, false);
	dwc3_disconnect_gadget(dwc);
	__dwc3_gadget_stop(dwc);

	return 0;
}

int dwc3_gadget_resume(struct dwc3 *dwc)
{
	int			ret;

	if (!dwc->gadget_driver || !dwc->softconnect)
		return 0;

	ret = __dwc3_gadget_start(dwc);
	if (ret < 0)
		goto err0;

	ret = dwc3_gadget_run_stop(dwc, true, false);
	if (ret < 0)
		goto err1;

	return 0;

err1:
	__dwc3_gadget_stop(dwc);

err0:
	return ret;
}

void dwc3_gadget_process_pending_events(struct dwc3 *dwc)
{
	if (dwc->pending_events) {
		dwc3_interrupt(dwc->irq_gadget, dwc->ev_buf);
		dwc->pending_events = false;
		enable_irq(dwc->irq_gadget);
	}
}