mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-26 04:25:27 +08:00
b537752e6c
We need to wait 5 s for EMP reset after firmware flash. Code was extracted
from OOT driver (ice v1.8.3 downloaded from sourceforge). Without this
wait, fw_activate let card in inconsistent state and recoverable only
by second flash/activate. Flash was tested on these fw's:
From -> To
3.00 -> 3.10/3.20
3.10 -> 3.00/3.20
3.20 -> 3.00/3.10
Reproducer:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
71: ens7f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
dmesg after flash:
[ 55.120788] ice: Copyright (c) 2018, Intel Corporation.
[ 55.274734] ice 0000:ca:00.0: Get PHY capabilities failed status = -5, continuing anyway
[ 55.569797] ice 0000:ca:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.28.0
[ 55.603629] ice 0000:ca:00.0: Get PHY capability failed.
[ 55.608951] ice 0000:ca:00.0: ice_init_nvm_phy_type failed: -5
[ 55.647348] ice 0000:ca:00.0: PTP init successful
[ 55.675536] ice 0000:ca:00.0: DCB is enabled in the hardware, max number of TCs supported on this port are 8
[ 55.685365] ice 0000:ca:00.0: FW LLDP is disabled, DCBx/LLDP in SW mode.
[ 55.692179] ice 0000:ca:00.0: Commit DCB Configuration to the hardware
[ 55.701382] ice 0000:ca:00.0: 126.024 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x8 link at 0000:c9:02.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
Reboot doesn’t help, only second flash/activate with OOT or patched
driver put card back in consistent state.
After patch:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
19: ens7f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
Fixes:
|
||
---|---|---|
.. | ||
e1000 | ||
e1000e | ||
fm10k | ||
i40e | ||
iavf | ||
ice | ||
igb | ||
igbvf | ||
igc | ||
ixgb | ||
ixgbe | ||
ixgbevf | ||
e100.c | ||
Kconfig | ||
Makefile |