mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-15 15:04:27 +08:00
3009 lines
99 KiB
Plaintext
3009 lines
99 KiB
Plaintext
|
|
#
|
|
# Network device configuration
|
|
#
|
|
|
|
menuconfig NETDEVICES
|
|
default y if UML
|
|
depends on NET
|
|
bool "Network device support"
|
|
---help---
|
|
You can say N here if you don't intend to connect your Linux box to
|
|
any other computer at all.
|
|
|
|
You'll have to say Y if your computer contains a network card that
|
|
you want to use under Linux. If you are going to run SLIP or PPP over
|
|
telephone line or null modem cable you need say Y here. Connecting
|
|
two machines with parallel ports using PLIP needs this, as well as
|
|
AX.25/KISS for sending Internet traffic over amateur radio links.
|
|
|
|
See also "The Linux Network Administrator's Guide" by Olaf Kirch and
|
|
Terry Dawson. Available at <http://www.tldp.org/guides.html>.
|
|
|
|
If unsure, say Y.
|
|
|
|
# All the following symbols are dependent on NETDEVICES - do not repeat
|
|
# that for each of the symbols.
|
|
if NETDEVICES
|
|
|
|
config IFB
|
|
tristate "Intermediate Functional Block support"
|
|
depends on NET_CLS_ACT
|
|
---help---
|
|
This is an intermediate driver that allows sharing of
|
|
resources.
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called ifb. If you want to use more than one ifb
|
|
device at a time, you need to compile this driver as a module.
|
|
Instead of 'ifb', the devices will then be called 'ifb0',
|
|
'ifb1' etc.
|
|
Look at the iproute2 documentation directory for usage etc
|
|
|
|
config DUMMY
|
|
tristate "Dummy net driver support"
|
|
---help---
|
|
This is essentially a bit-bucket device (i.e. traffic you send to
|
|
this device is consigned into oblivion) with a configurable IP
|
|
address. It is most commonly used in order to make your currently
|
|
inactive SLIP address seem like a real address for local programs.
|
|
If you use SLIP or PPP, you might want to say Y here. Since this
|
|
thing often comes in handy, the default is Y. It won't enlarge your
|
|
kernel either. What a deal. Read about it in the Network
|
|
Administrator's Guide, available from
|
|
<http://www.tldp.org/docs.html#guide>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called dummy. If you want to use more than one dummy
|
|
device at a time, you need to compile this driver as a module.
|
|
Instead of 'dummy', the devices will then be called 'dummy0',
|
|
'dummy1' etc.
|
|
|
|
config BONDING
|
|
tristate "Bonding driver support"
|
|
depends on INET
|
|
---help---
|
|
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
|
|
Channels together. This is called 'Etherchannel' by Cisco,
|
|
'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
|
|
|
|
The driver supports multiple bonding modes to allow for both high
|
|
performance and high availability operation.
|
|
|
|
Refer to <file:Documentation/networking/bonding.txt> for more
|
|
information.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called bonding.
|
|
|
|
config MACVLAN
|
|
tristate "MAC-VLAN support (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL
|
|
---help---
|
|
This allows one to create virtual interfaces that map packets to
|
|
or from specific MAC addresses to a particular interface.
|
|
|
|
Macvlan devices can be added using the "ip" command from the
|
|
iproute2 package starting with the iproute2-2.6.23 release:
|
|
|
|
"ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called macvlan.
|
|
|
|
config EQUALIZER
|
|
tristate "EQL (serial line load balancing) support"
|
|
---help---
|
|
If you have two serial connections to some other computer (this
|
|
usually requires two modems and two telephone lines) and you use
|
|
SLIP (the protocol for sending Internet traffic over telephone
|
|
lines) or PPP (a better SLIP) on them, you can make them behave like
|
|
one double speed connection using this driver. Naturally, this has
|
|
to be supported at the other end as well, either with a similar EQL
|
|
Linux driver or with a Livingston Portmaster 2e.
|
|
|
|
Say Y if you want this and read
|
|
<file:Documentation/networking/eql.txt>. You may also want to read
|
|
section 6.2 of the NET-3-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called eql. If unsure, say N.
|
|
|
|
config TUN
|
|
tristate "Universal TUN/TAP device driver support"
|
|
select CRC32
|
|
---help---
|
|
TUN/TAP provides packet reception and transmission for user space
|
|
programs. It can be viewed as a simple Point-to-Point or Ethernet
|
|
device, which instead of receiving packets from a physical media,
|
|
receives them from user space program and instead of sending packets
|
|
via physical media writes them to the user space program.
|
|
|
|
When a program opens /dev/net/tun, driver creates and registers
|
|
corresponding net device tunX or tapX. After a program closed above
|
|
devices, driver will automatically delete tunXX or tapXX device and
|
|
all routes corresponding to it.
|
|
|
|
Please read <file:Documentation/networking/tuntap.txt> for more
|
|
information.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called tun.
|
|
|
|
If you don't know what to use this for, you don't need it.
|
|
|
|
config VETH
|
|
tristate "Virtual ethernet pair device"
|
|
---help---
|
|
This device is a local ethernet tunnel. Devices are created in pairs.
|
|
When one end receives the packet it appears on its pair and vice
|
|
versa.
|
|
|
|
config NET_SB1000
|
|
tristate "General Instruments Surfboard 1000"
|
|
depends on PNP
|
|
---help---
|
|
This is a driver for the General Instrument (also known as
|
|
NextLevel) SURFboard 1000 internal
|
|
cable modem. This is an ISA card which is used by a number of cable
|
|
TV companies to provide cable modem access. It's a one-way
|
|
downstream-only cable modem, meaning that your upstream net link is
|
|
provided by your regular phone modem.
|
|
|
|
At present this driver only compiles as a module, so say M here if
|
|
you have this card. The module will be called sb1000. Then read
|
|
<file:Documentation/networking/README.sb1000> for information on how
|
|
to use this module, as it needs special ppp scripts for establishing
|
|
a connection. Further documentation and the necessary scripts can be
|
|
found at:
|
|
|
|
<http://www.jacksonville.net/~fventuri/>
|
|
<http://home.adelphia.net/~siglercm/sb1000.html>
|
|
<http://linuxpower.cx/~cable/>
|
|
|
|
If you don't have this card, of course say N.
|
|
|
|
source "drivers/net/arcnet/Kconfig"
|
|
|
|
source "drivers/net/phy/Kconfig"
|
|
|
|
#
|
|
# Ethernet
|
|
#
|
|
|
|
menuconfig NET_ETHERNET
|
|
bool "Ethernet (10 or 100Mbit)"
|
|
depends on !UML
|
|
---help---
|
|
Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
|
|
type of Local Area Network (LAN) in universities and companies.
|
|
|
|
Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
|
|
coaxial cable, linking computers in a chain), 10BASE-T or twisted
|
|
pair (10 Mbps over twisted pair cable, linking computers to central
|
|
hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
|
|
100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
|
|
100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
|
|
cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
|
|
[the 100BASE varieties are also known as Fast Ethernet], and Gigabit
|
|
Ethernet (1 Gbps over optical fiber or short copper links).
|
|
|
|
If your Linux machine will be connected to an Ethernet and you have
|
|
an Ethernet network interface card (NIC) installed in your computer,
|
|
say Y here and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. You will then also have
|
|
to say Y to the driver for your particular NIC.
|
|
|
|
Note that the answer to this question won't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about Ethernet network cards. If unsure, say N.
|
|
|
|
if NET_ETHERNET
|
|
|
|
config MII
|
|
tristate "Generic Media Independent Interface device support"
|
|
help
|
|
Most ethernet controllers have MII transceiver either as an external
|
|
or internal device. It is safe to say Y or M here even if your
|
|
ethernet card lack MII.
|
|
|
|
config MACB
|
|
tristate "Atmel MACB support"
|
|
depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
|
|
select PHYLIB
|
|
help
|
|
The Atmel MACB ethernet interface is found on many AT32 and AT91
|
|
parts. Say Y to include support for the MACB chip.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called macb.
|
|
|
|
source "drivers/net/arm/Kconfig"
|
|
|
|
config AX88796
|
|
tristate "ASIX AX88796 NE2000 clone support"
|
|
depends on ARM || MIPS || SUPERH
|
|
select CRC32
|
|
select MII
|
|
help
|
|
AX88796 driver, using platform bus to provide
|
|
chip detection and resources
|
|
|
|
config AX88796_93CX6
|
|
bool "ASIX AX88796 external 93CX6 eeprom support"
|
|
depends on AX88796
|
|
select EEPROM_93CX6
|
|
help
|
|
Select this if your platform comes with an external 93CX6 eeprom.
|
|
|
|
config MACE
|
|
tristate "MACE (Power Mac ethernet) support"
|
|
depends on PPC_PMAC && PPC32
|
|
select CRC32
|
|
help
|
|
Power Macintoshes and clones with Ethernet built-in on the
|
|
motherboard will usually use a MACE (Medium Access Control for
|
|
Ethernet) interface. Say Y to include support for the MACE chip.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called mace.
|
|
|
|
config MACE_AAUI_PORT
|
|
bool "Use AAUI port instead of TP by default"
|
|
depends on MACE
|
|
help
|
|
Some Apple machines (notably the Apple Network Server) which use the
|
|
MACE ethernet chip have an Apple AUI port (small 15-pin connector),
|
|
instead of an 8-pin RJ45 connector for twisted-pair ethernet. Say
|
|
Y here if you have such a machine. If unsure, say N.
|
|
The driver will default to AAUI on ANS anyway, and if you use it as
|
|
a module, you can provide the port_aaui=0|1 to force the driver.
|
|
|
|
config BMAC
|
|
tristate "BMAC (G3 ethernet) support"
|
|
depends on PPC_PMAC && PPC32
|
|
select CRC32
|
|
help
|
|
Say Y for support of BMAC Ethernet interfaces. These are used on G3
|
|
computers.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called bmac.
|
|
|
|
config ARIADNE
|
|
tristate "Ariadne support"
|
|
depends on ZORRO
|
|
help
|
|
If you have a Village Tronic Ariadne Ethernet adapter, say Y.
|
|
Otherwise, say N.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called ariadne.
|
|
|
|
config A2065
|
|
tristate "A2065 support"
|
|
depends on ZORRO
|
|
select CRC32
|
|
help
|
|
If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
|
|
say N.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called a2065.
|
|
|
|
config HYDRA
|
|
tristate "Hydra support"
|
|
depends on ZORRO
|
|
select CRC32
|
|
help
|
|
If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called hydra.
|
|
|
|
config ZORRO8390
|
|
tristate "Zorro NS8390-based Ethernet support"
|
|
depends on ZORRO
|
|
select CRC32
|
|
help
|
|
This driver is for Zorro Ethernet cards using an NS8390-compatible
|
|
chipset, like the Village Tronic Ariadne II and the Individual
|
|
Computers X-Surf Ethernet cards. If you have such a card, say Y.
|
|
Otherwise, say N.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called zorro8390.
|
|
|
|
config APNE
|
|
tristate "PCMCIA NE2000 support"
|
|
depends on AMIGA_PCMCIA
|
|
select CRC32
|
|
help
|
|
If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
|
|
say N.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called apne.
|
|
|
|
config MAC8390
|
|
bool "Macintosh NS 8390 based ethernet cards"
|
|
depends on MAC
|
|
select CRC32
|
|
help
|
|
If you want to include a driver to support Nubus or LC-PDS
|
|
Ethernet cards using an NS8390 chipset or its equivalent, say Y
|
|
and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
config MAC89x0
|
|
tristate "Macintosh CS89x0 based ethernet cards"
|
|
depends on MAC
|
|
---help---
|
|
Support for CS89x0 chipset based Ethernet cards. If you have a
|
|
Nubus or LC-PDS network (Ethernet) card of this type, say Y and
|
|
read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. This module will
|
|
be called mac89x0.
|
|
|
|
config MACSONIC
|
|
tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
|
|
depends on MAC
|
|
---help---
|
|
Support for NatSemi SONIC based Ethernet devices. This includes
|
|
the onboard Ethernet in many Quadras as well as some LC-PDS,
|
|
a few Nubus and all known Comm Slot Ethernet cards. If you have
|
|
one of these say Y and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. This module will
|
|
be called macsonic.
|
|
|
|
config MACMACE
|
|
bool "Macintosh (AV) onboard MACE ethernet"
|
|
depends on MAC
|
|
select CRC32
|
|
help
|
|
Support for the onboard AMD 79C940 MACE Ethernet controller used in
|
|
the 660AV and 840AV Macintosh. If you have one of these Macintoshes
|
|
say Y and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
config MVME147_NET
|
|
tristate "MVME147 (Lance) Ethernet support"
|
|
depends on MVME147
|
|
select CRC32
|
|
help
|
|
Support for the on-board Ethernet interface on the Motorola MVME147
|
|
single-board computer. Say Y here to include the
|
|
driver for this chip in your kernel.
|
|
To compile this driver as a module, choose M here.
|
|
|
|
config MVME16x_NET
|
|
tristate "MVME16x Ethernet support"
|
|
depends on MVME16x
|
|
help
|
|
This is the driver for the Ethernet interface on the Motorola
|
|
MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
|
|
driver for this chip in your kernel.
|
|
To compile this driver as a module, choose M here.
|
|
|
|
config BVME6000_NET
|
|
tristate "BVME6000 Ethernet support"
|
|
depends on BVME6000
|
|
help
|
|
This is the driver for the Ethernet interface on BVME4000 and
|
|
BVME6000 VME boards. Say Y here to include the driver for this chip
|
|
in your kernel.
|
|
To compile this driver as a module, choose M here.
|
|
|
|
config ATARILANCE
|
|
tristate "Atari Lance support"
|
|
depends on ATARI
|
|
help
|
|
Say Y to include support for several Atari Ethernet adapters based
|
|
on the AMD Lance chipset: RieblCard (with or without battery), or
|
|
PAMCard VME (also the version by Rhotron, with different addresses).
|
|
|
|
config SUN3LANCE
|
|
tristate "Sun3/Sun3x on-board LANCE support"
|
|
depends on SUN3 || SUN3X
|
|
help
|
|
Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
|
|
featured an AMD Lance 10Mbit Ethernet controller on board; say Y
|
|
here to compile in the Linux driver for this and enable Ethernet.
|
|
General Linux information on the Sun 3 and 3x series (now
|
|
discontinued) is at
|
|
<http://www.angelfire.com/ca2/tech68k/sun3.html>.
|
|
|
|
If you're not building a kernel for a Sun 3, say N.
|
|
|
|
config SUN3_82586
|
|
bool "Sun3 on-board Intel 82586 support"
|
|
depends on SUN3
|
|
help
|
|
This driver enables support for the on-board Intel 82586 based
|
|
Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
|
|
that this driver does not support 82586-based adapters on additional
|
|
VME boards.
|
|
|
|
config HPLANCE
|
|
bool "HP on-board LANCE support"
|
|
depends on DIO
|
|
select CRC32
|
|
help
|
|
If you want to use the builtin "LANCE" Ethernet controller on an
|
|
HP300 machine, say Y here.
|
|
|
|
config LASI_82596
|
|
tristate "Lasi ethernet"
|
|
depends on GSC
|
|
help
|
|
Say Y here to support the builtin Intel 82596 ethernet controller
|
|
found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
|
|
|
|
config SNI_82596
|
|
tristate "SNI RM ethernet"
|
|
depends on NET_ETHERNET && SNI_RM
|
|
help
|
|
Say Y here to support the on-board Intel 82596 ethernet controller
|
|
built into SNI RM machines.
|
|
|
|
config KORINA
|
|
tristate "Korina (IDT RC32434) Ethernet support"
|
|
depends on NET_ETHERNET && MIKROTIK_RB532
|
|
help
|
|
If you have a Mikrotik RouterBoard 500 or IDT RC32434
|
|
based system say Y. Otherwise say N.
|
|
|
|
config MIPS_JAZZ_SONIC
|
|
tristate "MIPS JAZZ onboard SONIC Ethernet support"
|
|
depends on MACH_JAZZ
|
|
help
|
|
This is the driver for the onboard card of MIPS Magnum 4000,
|
|
Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
|
|
|
|
config MIPS_AU1X00_ENET
|
|
bool "MIPS AU1000 Ethernet support"
|
|
depends on SOC_AU1X00
|
|
select PHYLIB
|
|
select CRC32
|
|
help
|
|
If you have an Alchemy Semi AU1X00 based system
|
|
say Y. Otherwise, say N.
|
|
|
|
config SGI_IOC3_ETH
|
|
bool "SGI IOC3 Ethernet"
|
|
depends on PCI && SGI_IP27
|
|
select CRC32
|
|
select MII
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
config MIPS_SIM_NET
|
|
tristate "MIPS simulator Network device"
|
|
depends on MIPS_SIM
|
|
help
|
|
The MIPSNET device is a simple Ethernet network device which is
|
|
emulated by the MIPS Simulator.
|
|
If you are not using a MIPSsim or are unsure, say N.
|
|
|
|
config SGI_O2MACE_ETH
|
|
tristate "SGI O2 MACE Fast Ethernet support"
|
|
depends on SGI_IP32=y
|
|
|
|
config STNIC
|
|
tristate "National DP83902AV support"
|
|
depends on SUPERH
|
|
select CRC32
|
|
help
|
|
Support for cards based on the National Semiconductor DP83902AV
|
|
ST-NIC Serial Network Interface Controller for Twisted Pair. This
|
|
is a 10Mbit/sec Ethernet controller. Product overview and specs at
|
|
<http://www.national.com/pf/DP/DP83902A.html>.
|
|
|
|
If unsure, say N.
|
|
|
|
config SH_ETH
|
|
tristate "Renesas SuperH Ethernet support"
|
|
depends on SUPERH && \
|
|
(CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \
|
|
CPU_SUBTYPE_SH7619)
|
|
select CRC32
|
|
select MII
|
|
select MDIO_BITBANG
|
|
select PHYLIB
|
|
help
|
|
Renesas SuperH Ethernet device driver.
|
|
This driver support SH7710, SH7712, SH7763 and SH7619.
|
|
|
|
config SUNLANCE
|
|
tristate "Sun LANCE support"
|
|
depends on SBUS
|
|
select CRC32
|
|
help
|
|
This driver supports the "le" interface present on all 32-bit Sparc
|
|
systems, on some older Ultra systems and as an Sbus option. These
|
|
cards are based on the AMD Lance chipset, which is better known
|
|
via the NE2100 cards.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sunlance.
|
|
|
|
config HAPPYMEAL
|
|
tristate "Sun Happy Meal 10/100baseT support"
|
|
depends on SBUS || PCI
|
|
select CRC32
|
|
help
|
|
This driver supports the "hme" interface present on most Ultra
|
|
systems and as an option on older Sbus systems. This driver supports
|
|
both PCI and Sbus devices. This driver also supports the "qfe" quad
|
|
100baseT device available in both PCI and Sbus configurations.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sunhme.
|
|
|
|
config SUNBMAC
|
|
tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
|
|
depends on SBUS && EXPERIMENTAL
|
|
select CRC32
|
|
help
|
|
This driver supports the "be" interface available as an Sbus option.
|
|
This is Sun's older 100baseT Ethernet device.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sunbmac.
|
|
|
|
config SUNQE
|
|
tristate "Sun QuadEthernet support"
|
|
depends on SBUS
|
|
select CRC32
|
|
help
|
|
This driver supports the "qe" 10baseT Ethernet device, available as
|
|
an Sbus option. Note that this is not the same as Quad FastEthernet
|
|
"qfe" which is supported by the Happy Meal driver instead.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sunqe.
|
|
|
|
config SUNGEM
|
|
tristate "Sun GEM support"
|
|
depends on PCI
|
|
select CRC32
|
|
help
|
|
Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
|
|
<http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.
|
|
|
|
config CASSINI
|
|
tristate "Sun Cassini support"
|
|
depends on PCI
|
|
select CRC32
|
|
help
|
|
Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
|
|
<http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
|
|
|
|
config SUNVNET
|
|
tristate "Sun Virtual Network support"
|
|
depends on SUN_LDOMS
|
|
help
|
|
Support for virtual network devices under Sun Logical Domains.
|
|
|
|
config NET_VENDOR_3COM
|
|
bool "3COM cards"
|
|
depends on ISA || EISA || MCA || PCI
|
|
help
|
|
If you have a network (Ethernet) card belonging to this class, say Y
|
|
and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about 3COM cards. If you say Y, you will be asked for
|
|
your specific card in the following questions.
|
|
|
|
config EL1
|
|
tristate "3c501 \"EtherLink\" support"
|
|
depends on NET_VENDOR_3COM && ISA
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. Also, consider buying a
|
|
new card, since the 3c501 is slow, broken, and obsolete: you will
|
|
have problems. Some people suggest to ping ("man ping") a nearby
|
|
machine every minute ("man cron") when using this card.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c501.
|
|
|
|
config EL2
|
|
tristate "3c503 \"EtherLink II\" support"
|
|
depends on NET_VENDOR_3COM && ISA
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c503.
|
|
|
|
config ELPLUS
|
|
tristate "3c505 \"EtherLink Plus\" support"
|
|
depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
|
|
---help---
|
|
Information about this network (Ethernet) card can be found in
|
|
<file:Documentation/networking/3c505.txt>. If you have a card of
|
|
this type, say Y and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c505.
|
|
|
|
config EL16
|
|
tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
|
|
depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c507.
|
|
|
|
config EL3
|
|
tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
|
|
depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
|
|
---help---
|
|
If you have a network (Ethernet) card belonging to the 3Com
|
|
EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
|
|
from <http://www.tldp.org/docs.html#howto>.
|
|
|
|
If your card is not working you may need to use the DOS
|
|
setup disk to disable Plug & Play mode, and to select the default
|
|
media type.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c509.
|
|
|
|
config 3C515
|
|
tristate "3c515 ISA \"Fast EtherLink\""
|
|
depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
|
|
help
|
|
If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
|
|
network card, say Y and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c515.
|
|
|
|
config ELMC
|
|
tristate "3c523 \"EtherLink/MC\" support"
|
|
depends on NET_VENDOR_3COM && MCA_LEGACY
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c523.
|
|
|
|
config ELMC_II
|
|
tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
|
|
depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called 3c527.
|
|
|
|
config VORTEX
|
|
tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
|
|
depends on NET_VENDOR_3COM && (PCI || EISA)
|
|
select MII
|
|
---help---
|
|
This option enables driver support for a large number of 10Mbps and
|
|
10/100Mbps EISA, PCI and PCMCIA 3Com network cards:
|
|
|
|
"Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
|
|
"Boomerang" (EtherLink XL 3c900 or 3c905) PCI
|
|
"Cyclone" (3c540/3c900/3c905/3c980/3c575/3c656) PCI and Cardbus
|
|
"Tornado" (3c905) PCI
|
|
"Hurricane" (3c555/3cSOHO) PCI
|
|
|
|
If you have such a card, say Y and read the Ethernet-HOWTO,
|
|
available from <http://www.tldp.org/docs.html#howto>. More
|
|
specific information is in
|
|
<file:Documentation/networking/vortex.txt> and in the comments at
|
|
the beginning of <file:drivers/net/3c59x.c>.
|
|
|
|
To compile this support as a module, choose M here.
|
|
|
|
config TYPHOON
|
|
tristate "3cr990 series \"Typhoon\" support"
|
|
depends on NET_VENDOR_3COM && PCI
|
|
select CRC32
|
|
---help---
|
|
This option enables driver support for the 3cr990 series of cards:
|
|
|
|
3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97,
|
|
3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server,
|
|
3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR
|
|
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called typhoon.
|
|
|
|
config LANCE
|
|
tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
|
|
depends on ISA && ISA_DMA_API
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
|
|
of this type.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called lance. This is recommended.
|
|
|
|
config NET_VENDOR_SMC
|
|
bool "Western Digital/SMC cards"
|
|
depends on ISA || MCA || EISA || MAC
|
|
help
|
|
If you have a network (Ethernet) card belonging to this class, say Y
|
|
and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about Western Digital cards. If you say Y, you will be
|
|
asked for your specific card in the following questions.
|
|
|
|
config WD80x3
|
|
tristate "WD80*3 support"
|
|
depends on NET_VENDOR_SMC && ISA
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called wd.
|
|
|
|
config ULTRAMCA
|
|
tristate "SMC Ultra MCA support"
|
|
depends on NET_VENDOR_SMC && MCA
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type and are running
|
|
an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
|
|
available from <http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called smc-mca.
|
|
|
|
config ULTRA
|
|
tristate "SMC Ultra support"
|
|
depends on NET_VENDOR_SMC && ISA
|
|
select CRC32
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
Important: There have been many reports that, with some motherboards
|
|
mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
|
|
such as some BusLogic models) causes corruption problems with many
|
|
operating systems. The Linux smc-ultra driver has a work-around for
|
|
this but keep it in mind if you have such a SCSI card and have
|
|
problems.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called smc-ultra.
|
|
|
|
config ULTRA32
|
|
tristate "SMC Ultra32 EISA support"
|
|
depends on NET_VENDOR_SMC && EISA
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called smc-ultra32.
|
|
|
|
config BFIN_MAC
|
|
tristate "Blackfin on-chip MAC support"
|
|
depends on NET_ETHERNET && (BF526 || BF527 || BF536 || BF537)
|
|
select CRC32
|
|
select MII
|
|
select PHYLIB
|
|
select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
|
|
help
|
|
This is the driver for Blackfin on-chip mac device. Say Y if you want it
|
|
compiled into the kernel. This driver is also available as a module
|
|
( = code which can be inserted in and removed from the running kernel
|
|
whenever you want). The module will be called bfin_mac.
|
|
|
|
config BFIN_MAC_USE_L1
|
|
bool "Use L1 memory for rx/tx packets"
|
|
depends on BFIN_MAC && (BF527 || BF537)
|
|
default y
|
|
help
|
|
To get maximum network performance, you should use L1 memory as rx/tx buffers.
|
|
Say N here if you want to reserve L1 memory for other uses.
|
|
|
|
config BFIN_TX_DESC_NUM
|
|
int "Number of transmit buffer packets"
|
|
depends on BFIN_MAC
|
|
range 6 10 if BFIN_MAC_USE_L1
|
|
range 10 100
|
|
default "10"
|
|
help
|
|
Set the number of buffer packets used in driver.
|
|
|
|
config BFIN_RX_DESC_NUM
|
|
int "Number of receive buffer packets"
|
|
depends on BFIN_MAC
|
|
range 20 100 if BFIN_MAC_USE_L1
|
|
range 20 800
|
|
default "20"
|
|
help
|
|
Set the number of buffer packets used in driver.
|
|
|
|
config BFIN_MAC_RMII
|
|
bool "RMII PHY Interface (EXPERIMENTAL)"
|
|
depends on BFIN_MAC && EXPERIMENTAL
|
|
default y if BFIN527_EZKIT
|
|
default n if BFIN537_STAMP
|
|
help
|
|
Use Reduced PHY MII Interface
|
|
|
|
config SMC9194
|
|
tristate "SMC 9194 support"
|
|
depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
|
|
select CRC32
|
|
---help---
|
|
This is support for the SMC9xxx based Ethernet cards. Choose this
|
|
option if you have a DELL laptop with the docking station, or
|
|
another SMC9192/9194 based chipset. Say Y if you want it compiled
|
|
into the kernel, and read the file
|
|
<file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
|
|
available from <http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called smc9194.
|
|
|
|
config SMC91X
|
|
tristate "SMC 91C9x/91C1xxx support"
|
|
select CRC32
|
|
select MII
|
|
depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
|
|
SOC_AU1X00 || BLACKFIN || MN10300
|
|
help
|
|
This is a driver for SMC's 91x series of Ethernet chipsets,
|
|
including the SMC91C94 and the SMC91C111. Say Y if you want it
|
|
compiled into the kernel, and read the file
|
|
<file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
|
|
available from <http://www.linuxdoc.org/docs.html#howto>.
|
|
|
|
This driver is also available as a module ( = code which can be
|
|
inserted in and removed from the running kernel whenever you want).
|
|
The module will be called smc91x. If you want to compile it as a
|
|
module, say M here and read <file:Documentation/kbuild/modules.txt>.
|
|
|
|
config NET_NETX
|
|
tristate "NetX Ethernet support"
|
|
select MII
|
|
depends on ARCH_NETX
|
|
help
|
|
This is support for the Hilscher netX builtin Ethernet ports
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called netx-eth.
|
|
|
|
config DM9000
|
|
tristate "DM9000 support"
|
|
depends on ARM || BLACKFIN || MIPS
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
Support for DM9000 chipset.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called dm9000.
|
|
|
|
config DM9000_DEBUGLEVEL
|
|
int "DM9000 maximum debug level"
|
|
depends on DM9000
|
|
default 4
|
|
help
|
|
The maximum level of debugging code compiled into the DM9000
|
|
driver.
|
|
|
|
config DM9000_FORCE_SIMPLE_PHY_POLL
|
|
bool "Force simple NSR based PHY polling"
|
|
depends on DM9000
|
|
---help---
|
|
This configuration forces the DM9000 to use the NSR's LinkStatus
|
|
bit to determine if the link is up or down instead of the more
|
|
costly MII PHY reads. Note, this will not work if the chip is
|
|
operating with an external PHY.
|
|
|
|
config ENC28J60
|
|
tristate "ENC28J60 support"
|
|
depends on EXPERIMENTAL && SPI && NET_ETHERNET
|
|
select CRC32
|
|
---help---
|
|
Support for the Microchip EN28J60 ethernet chip.
|
|
|
|
To compile this driver as a module, choose M here. The module will be
|
|
called enc28j60.
|
|
|
|
config ENC28J60_WRITEVERIFY
|
|
bool "Enable write verify"
|
|
depends on ENC28J60
|
|
---help---
|
|
Enable the verify after the buffer write useful for debugging purpose.
|
|
If unsure, say N.
|
|
|
|
config SMC911X
|
|
tristate "SMSC LAN911[5678] support"
|
|
select CRC32
|
|
select MII
|
|
depends on ARCH_PXA || SUPERH
|
|
help
|
|
This is a driver for SMSC's LAN911x series of Ethernet chipsets
|
|
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
|
|
Say Y if you want it compiled into the kernel,
|
|
and read the Ethernet-HOWTO, available from
|
|
<http://www.linuxdoc.org/docs.html#howto>.
|
|
|
|
This driver is also available as a module. The module will be
|
|
called smc911x. If you want to compile it as a module, say M
|
|
here and read <file:Documentation/kbuild/modules.txt>
|
|
|
|
config NET_VENDOR_RACAL
|
|
bool "Racal-Interlan (Micom) NI cards"
|
|
depends on ISA
|
|
help
|
|
If you have a network (Ethernet) card belonging to this class, such
|
|
as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
|
|
available from <http://www.tldp.org/docs.html#howto>.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about NI cards. If you say Y, you will be asked for
|
|
your specific card in the following questions.
|
|
|
|
config NI5010
|
|
tristate "NI5010 support (EXPERIMENTAL)"
|
|
depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. Note that this is still
|
|
experimental code.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ni5010.
|
|
|
|
config NI52
|
|
tristate "NI5210 support"
|
|
depends on NET_VENDOR_RACAL && ISA
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ni52.
|
|
|
|
config NI65
|
|
tristate "NI6510 support"
|
|
depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ni65.
|
|
|
|
source "drivers/net/tulip/Kconfig"
|
|
|
|
config AT1700
|
|
tristate "AT1700/1720 support (EXPERIMENTAL)"
|
|
depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
|
|
select CRC32
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called at1700.
|
|
|
|
config DEPCA
|
|
tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
|
|
depends on ISA || EISA || MCA
|
|
select CRC32
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto> as well as
|
|
<file:drivers/net/depca.c>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called depca.
|
|
|
|
config HP100
|
|
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
|
|
depends on ISA || EISA || PCI
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called hp100.
|
|
|
|
config NET_ISA
|
|
bool "Other ISA cards"
|
|
depends on ISA
|
|
---help---
|
|
If your network (Ethernet) card hasn't been mentioned yet and its
|
|
bus system (that's the way the cards talks to the other components
|
|
of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
|
|
Make sure you know the name of your card. Read the Ethernet-HOWTO,
|
|
available from <http://www.tldp.org/docs.html#howto>.
|
|
|
|
If unsure, say Y.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the remaining ISA network card questions. If you say Y, you will be
|
|
asked for your specific card in the following questions.
|
|
|
|
config E2100
|
|
tristate "Cabletron E21xx support"
|
|
depends on NET_ISA
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called e2100.
|
|
|
|
config EWRK3
|
|
tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
|
|
depends on NET_ISA
|
|
select CRC32
|
|
---help---
|
|
This driver supports the DE203, DE204 and DE205 network (Ethernet)
|
|
cards. If this is for you, say Y and read
|
|
<file:Documentation/networking/ewrk3.txt> in the kernel source as
|
|
well as the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ewrk3.
|
|
|
|
config EEXPRESS
|
|
tristate "EtherExpress 16 support"
|
|
depends on NET_ISA
|
|
---help---
|
|
If you have an EtherExpress16 network (Ethernet) card, say Y and
|
|
read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. Note that the Intel
|
|
EtherExpress16 card used to be regarded as a very poor choice
|
|
because the driver was very unreliable. We now have a new driver
|
|
that should do better.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called eexpress.
|
|
|
|
config EEXPRESS_PRO
|
|
tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
|
|
depends on NET_ISA
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y. This
|
|
driver supports Intel i82595{FX,TX} based boards. Note however
|
|
that the EtherExpress PRO/100 Ethernet card has its own separate
|
|
driver. Please read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called eepro.
|
|
|
|
config HPLAN_PLUS
|
|
tristate "HP PCLAN+ (27247B and 27252A) support"
|
|
depends on NET_ISA
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called hp-plus.
|
|
|
|
config HPLAN
|
|
tristate "HP PCLAN (27245 and other 27xxx series) support"
|
|
depends on NET_ISA
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called hp.
|
|
|
|
config LP486E
|
|
tristate "LP486E on board Ethernet"
|
|
depends on NET_ISA
|
|
help
|
|
Say Y here to support the 82596-based on-board Ethernet controller
|
|
for the Panther motherboard, which is one of the two shipped in the
|
|
Intel Professional Workstation.
|
|
|
|
config ETH16I
|
|
tristate "ICL EtherTeam 16i/32 support"
|
|
depends on NET_ISA
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called eth16i.
|
|
|
|
config NE2000
|
|
tristate "NE2000/NE1000 support"
|
|
depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
|
|
select CRC32
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. Many Ethernet cards
|
|
without a specific driver are compatible with NE2000.
|
|
|
|
If you have a PCI NE2000 card however, say N here and Y to "PCI
|
|
NE2000 and clone support" under "EISA, VLB, PCI and on board
|
|
controllers" below. If you have a NE2000 card and are running on
|
|
an MCA system (a bus system used on some IBM PS/2 computers and
|
|
laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
|
|
below.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ne.
|
|
|
|
config ZNET
|
|
tristate "Zenith Z-Note support (EXPERIMENTAL)"
|
|
depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
|
|
help
|
|
The Zenith Z-Note notebook computer has a built-in network
|
|
(Ethernet) card, and this is the Linux driver for it. Note that the
|
|
IBM Thinkpad 300 is compatible with the Z-Note and is also supported
|
|
by this driver. Read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
config SEEQ8005
|
|
tristate "SEEQ8005 support (EXPERIMENTAL)"
|
|
depends on NET_ISA && EXPERIMENTAL
|
|
help
|
|
This is a driver for the SEEQ 8005 network (Ethernet) card. If this
|
|
is for you, read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called seeq8005.
|
|
|
|
config NE2_MCA
|
|
tristate "NE/2 (ne2000 MCA version) support"
|
|
depends on MCA_LEGACY
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ne2.
|
|
|
|
config IBMLANA
|
|
tristate "IBM LAN Adapter/A support"
|
|
depends on MCA
|
|
---help---
|
|
This is a Micro Channel Ethernet adapter. You need to set
|
|
CONFIG_MCA to use this driver. It is both available as an in-kernel
|
|
driver and as a module.
|
|
|
|
To compile this driver as a module, choose M here. The only
|
|
currently supported card is the IBM LAN Adapter/A for Ethernet. It
|
|
will both support 16K and 32K memory windows, however a 32K window
|
|
gives a better security against packet losses. Usage of multiple
|
|
boards with this driver should be possible, but has not been tested
|
|
up to now due to lack of hardware.
|
|
|
|
config IBMVETH
|
|
tristate "IBM LAN Virtual Ethernet support"
|
|
depends on PPC_PSERIES
|
|
---help---
|
|
This driver supports virtual ethernet adapters on newer IBM iSeries
|
|
and pSeries systems.
|
|
|
|
To compile this driver as a module, choose M here. The module will
|
|
be called ibmveth.
|
|
|
|
source "drivers/net/ibm_newemac/Kconfig"
|
|
|
|
config NET_PCI
|
|
bool "EISA, VLB, PCI and on board controllers"
|
|
depends on ISA || EISA || PCI
|
|
help
|
|
This is another class of network cards which attach directly to the
|
|
bus. If you have one of those, say Y and read the Ethernet-HOWTO,
|
|
available from <http://www.tldp.org/docs.html#howto>.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about this class of network cards. If you say Y, you
|
|
will be asked for your specific card in the following questions. If
|
|
you are unsure, say Y.
|
|
|
|
config PCNET32
|
|
tristate "AMD PCnet32 PCI support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
|
|
answer Y here and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called pcnet32.
|
|
|
|
config AMD8111_ETH
|
|
tristate "AMD 8111 (new PCI lance) support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
If you have an AMD 8111-based PCI lance ethernet card,
|
|
answer Y here and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called amd8111e.
|
|
|
|
config ADAPTEC_STARFIRE
|
|
tristate "Adaptec Starfire/DuraLAN support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
|
|
adapter. The DuraLAN chip is used on the 64 bit PCI boards from
|
|
Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
|
|
driver.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called starfire. This is recommended.
|
|
|
|
config AC3200
|
|
tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
|
|
depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ac3200.
|
|
|
|
config APRICOT
|
|
tristate "Apricot Xen-II on board Ethernet"
|
|
depends on NET_PCI && ISA
|
|
help
|
|
If you have a network (Ethernet) controller of this type, say Y and
|
|
read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called apricot.
|
|
|
|
config B44
|
|
tristate "Broadcom 440x/47xx ethernet support"
|
|
depends on SSB_POSSIBLE && HAS_DMA
|
|
select SSB
|
|
select MII
|
|
help
|
|
If you have a network (Ethernet) controller of this type, say Y
|
|
or M and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called b44.
|
|
|
|
# Auto-select SSB PCI-HOST support, if possible
|
|
config B44_PCI_AUTOSELECT
|
|
bool
|
|
depends on B44 && SSB_PCIHOST_POSSIBLE
|
|
select SSB_PCIHOST
|
|
default y
|
|
|
|
# Auto-select SSB PCICORE driver, if possible
|
|
config B44_PCICORE_AUTOSELECT
|
|
bool
|
|
depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
|
|
select SSB_DRIVER_PCICORE
|
|
default y
|
|
|
|
config B44_PCI
|
|
bool
|
|
depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
|
|
default y
|
|
|
|
config FORCEDETH
|
|
tristate "nForce Ethernet support"
|
|
depends on NET_PCI && PCI
|
|
help
|
|
If you have a network (Ethernet) controller of this type, say Y and
|
|
read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called forcedeth.
|
|
|
|
config FORCEDETH_NAPI
|
|
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
|
|
depends on FORCEDETH && EXPERIMENTAL
|
|
help
|
|
NAPI is a new driver API designed to reduce CPU and interrupt load
|
|
when the driver is receiving lots of packets from the card. It is
|
|
still somewhat experimental and thus not yet enabled by default.
|
|
|
|
If your estimated Rx load is 10kpps or more, or if the card will be
|
|
deployed on potentially unfriendly networks (e.g. in a firewall),
|
|
then say Y here.
|
|
|
|
If in doubt, say N.
|
|
|
|
config CS89x0
|
|
tristate "CS89x0 support"
|
|
depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X)
|
|
---help---
|
|
Support for CS89x0 chipset based Ethernet cards. If you have a
|
|
network (Ethernet) card of this type, say Y and read the
|
|
Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto> as well as
|
|
<file:Documentation/networking/cs89x0.txt>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called cs89x0.
|
|
|
|
config TC35815
|
|
tristate "TOSHIBA TC35815 Ethernet support"
|
|
depends on NET_PCI && PCI && MIPS
|
|
select PHYLIB
|
|
|
|
config EEPRO100
|
|
tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
|
|
depends on NET_PCI && PCI
|
|
select MII
|
|
help
|
|
If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
|
|
card, say Y and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called eepro100.
|
|
|
|
|
|
config E100
|
|
tristate "Intel(R) PRO/100+ support"
|
|
depends on NET_PCI && PCI
|
|
select MII
|
|
---help---
|
|
This driver supports Intel(R) PRO/100 family of adapters.
|
|
To verify that your adapter is supported, find the board ID number
|
|
on the adapter. Look for a label that has a barcode and a number
|
|
in the format 123456-001 (six digits hyphen three digits).
|
|
|
|
Use the above information and the Adapter & Driver ID Guide at:
|
|
|
|
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
|
|
|
|
to identify the adapter.
|
|
|
|
For the latest Intel PRO/100 network driver for Linux, see:
|
|
|
|
<http://appsr.intel.com/scripts-df/support_intel.asp>
|
|
|
|
More specific information on configuring the driver is in
|
|
<file:Documentation/networking/e100.txt>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called e100.
|
|
|
|
config LNE390
|
|
tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
|
|
depends on NET_PCI && EISA && EXPERIMENTAL
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called lne390.
|
|
|
|
config FEALNX
|
|
tristate "Myson MTD-8xx PCI Ethernet support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
|
|
cards. Specifications and data at
|
|
<http://www.myson.com.hk/mtd/datasheet/>.
|
|
|
|
config NATSEMI
|
|
tristate "National Semiconductor DP8381x series PCI Ethernet support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
help
|
|
This driver is for the National Semiconductor DP83810 series,
|
|
which is used in cards from PureData, NetGear, Linksys
|
|
and others, including the 83815 chip.
|
|
More specific information and updates are available from
|
|
<http://www.scyld.com/network/natsemi.html>.
|
|
|
|
config NE2K_PCI
|
|
tristate "PCI NE2000 and clones support (see help)"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
---help---
|
|
This driver is for NE2000 compatible PCI cards. It will not work
|
|
with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
|
|
support" below). If you have a PCI NE2000 network (Ethernet) card,
|
|
say Y and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
This driver also works for the following NE2000 clone cards:
|
|
RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2
|
|
NetVin NV5000SC Via 86C926 SureCom NE34 Winbond
|
|
Holtek HT80232 Holtek HT80229
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ne2k-pci.
|
|
|
|
config NE3210
|
|
tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
|
|
depends on NET_PCI && EISA && EXPERIMENTAL
|
|
select CRC32
|
|
---help---
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. Note that this driver
|
|
will NOT WORK for NE3200 cards as they are completely different.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ne3210.
|
|
|
|
config ES3210
|
|
tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
|
|
depends on NET_PCI && EISA && EXPERIMENTAL
|
|
select CRC32
|
|
help
|
|
If you have a network (Ethernet) card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called es3210.
|
|
|
|
config 8139CP
|
|
tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
|
|
depends on NET_PCI && PCI && EXPERIMENTAL
|
|
select CRC32
|
|
select MII
|
|
help
|
|
This is a driver for the Fast Ethernet PCI network cards based on
|
|
the RTL8139C+ chips. If you have one of those, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called 8139cp. This is recommended.
|
|
|
|
config 8139TOO
|
|
tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
This is a driver for the Fast Ethernet PCI network cards based on
|
|
the RTL 8129/8130/8139 chips. If you have one of those, say Y and
|
|
read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called 8139too. This is recommended.
|
|
|
|
config 8139TOO_PIO
|
|
bool "Use PIO instead of MMIO"
|
|
default y
|
|
depends on 8139TOO
|
|
help
|
|
This instructs the driver to use programmed I/O ports (PIO) instead
|
|
of PCI shared memory (MMIO). This can possibly solve some problems
|
|
in case your mainboard has memory consistency issues. If unsure,
|
|
say N.
|
|
|
|
config 8139TOO_TUNE_TWISTER
|
|
bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
|
|
depends on 8139TOO
|
|
help
|
|
This implements a function which might come in handy in case you
|
|
are using low quality on long cabling. It is required for RealTek
|
|
RTL-8139 revision K boards, and totally unused otherwise. It tries
|
|
to match the transceiver to the cable characteristics. This is
|
|
experimental since hardly documented by the manufacturer.
|
|
If unsure, say Y.
|
|
|
|
config 8139TOO_8129
|
|
bool "Support for older RTL-8129/8130 boards"
|
|
depends on 8139TOO
|
|
help
|
|
This enables support for the older and uncommon RTL-8129 and
|
|
RTL-8130 chips, which support MII via an external transceiver,
|
|
instead of an internal one. Disabling this option will save some
|
|
memory by making the code size smaller. If unsure, say Y.
|
|
|
|
config 8139_OLD_RX_RESET
|
|
bool "Use older RX-reset method"
|
|
depends on 8139TOO
|
|
help
|
|
The 8139too driver was recently updated to contain a more rapid
|
|
reset sequence, in the face of severe receive errors. This "new"
|
|
RX-reset method should be adequate for all boards. But if you
|
|
experience problems, you can enable this option to restore the
|
|
old RX-reset behavior. If unsure, say N.
|
|
|
|
config R6040
|
|
tristate "RDC R6040 Fast Ethernet Adapter support (EXPERIMENTAL)"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
This is a driver for the R6040 Fast Ethernet MACs found in the
|
|
the RDC R-321x System-on-chips.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called r6040. This is recommended.
|
|
|
|
config SIS900
|
|
tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
This is a driver for the Fast Ethernet PCI network cards based on
|
|
the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
|
|
SiS 630 and SiS 540 chipsets.
|
|
|
|
This driver also supports AMD 79C901 HomePNA so that you can use
|
|
your phone line as a network cable.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sis900. This is recommended.
|
|
|
|
config EPIC100
|
|
tristate "SMC EtherPower II"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC,
|
|
which is based on the SMC83c17x (EPIC/100).
|
|
More specific information and updates are available from
|
|
<http://www.scyld.com/network/epic100.html>.
|
|
|
|
config SUNDANCE
|
|
tristate "Sundance Alta support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
This driver is for the Sundance "Alta" chip.
|
|
More specific information and updates are available from
|
|
<http://www.scyld.com/network/sundance.html>.
|
|
|
|
config SUNDANCE_MMIO
|
|
bool "Use MMIO instead of PIO"
|
|
depends on SUNDANCE
|
|
help
|
|
Enable memory-mapped I/O for interaction with Sundance NIC registers.
|
|
Do NOT enable this by default, PIO (enabled when MMIO is disabled)
|
|
is known to solve bugs on certain chips.
|
|
|
|
If unsure, say N.
|
|
|
|
config TLAN
|
|
tristate "TI ThunderLAN support"
|
|
depends on NET_PCI && (PCI || EISA)
|
|
---help---
|
|
If you have a PCI Ethernet network card based on the ThunderLAN chip
|
|
which is supported by this driver, say Y and read the
|
|
Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
Devices currently supported by this driver are Compaq Netelligent,
|
|
Compaq NetFlex and Olicom cards. Please read the file
|
|
<file:Documentation/networking/tlan.txt> for more details.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called tlan.
|
|
|
|
Please email feedback to <torben.mathiasen@compaq.com>.
|
|
|
|
config VIA_RHINE
|
|
tristate "VIA Rhine support"
|
|
depends on NET_PCI && PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
|
|
Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
|
|
Ethernet functions can also be found integrated on South Bridges
|
|
(e.g. VT8235).
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called via-rhine.
|
|
|
|
config VIA_RHINE_MMIO
|
|
bool "Use MMIO instead of PIO"
|
|
depends on VIA_RHINE
|
|
help
|
|
This instructs the driver to use PCI shared memory (MMIO) instead of
|
|
programmed I/O ports (PIO). Enabling this gives an improvement in
|
|
processing time in parts of the driver.
|
|
|
|
If unsure, say Y.
|
|
|
|
config SC92031
|
|
tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
|
|
depends on NET_PCI && PCI && EXPERIMENTAL
|
|
select CRC32
|
|
---help---
|
|
This is a driver for the Fast Ethernet PCI network cards based on
|
|
the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
|
|
have one of these, say Y here.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sc92031. This is recommended.
|
|
|
|
config CPMAC
|
|
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
|
|
depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
|
|
select PHYLIB
|
|
help
|
|
TI AR7 CPMAC Ethernet support
|
|
|
|
config NET_POCKET
|
|
bool "Pocket and portable adapters"
|
|
depends on PARPORT
|
|
---help---
|
|
Cute little network (Ethernet) devices which attach to the parallel
|
|
port ("pocket adapters"), commonly used with laptops. If you have
|
|
one of those, say Y and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
If you want to plug a network (or some other) card into the PCMCIA
|
|
(or PC-card) slot of your laptop instead (PCMCIA is the standard for
|
|
credit card size extension cards used by all modern laptops), you
|
|
need the pcmcia-cs package (location contained in the file
|
|
<file:Documentation/Changes>) and you can say N here.
|
|
|
|
Laptop users should read the Linux Laptop home page at
|
|
<http://www.linux-on-laptops.com/> or
|
|
Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about this class of network devices. If you say Y, you
|
|
will be asked for your specific device in the following questions.
|
|
|
|
config ATP
|
|
tristate "AT-LAN-TEC/RealTek pocket adapter support"
|
|
depends on NET_POCKET && PARPORT && X86
|
|
select CRC32
|
|
---help---
|
|
This is a network (Ethernet) device which attaches to your parallel
|
|
port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
|
|
available from <http://www.tldp.org/docs.html#howto>, if you
|
|
want to use this. If you intend to use this driver, you should have
|
|
said N to the "Parallel printer support", because the two drivers
|
|
don't like each other.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called atp.
|
|
|
|
config DE600
|
|
tristate "D-Link DE600 pocket adapter support"
|
|
depends on NET_POCKET && PARPORT
|
|
---help---
|
|
This is a network (Ethernet) device which attaches to your parallel
|
|
port. Read <file:Documentation/networking/DLINK.txt> as well as the
|
|
Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>, if you want to use
|
|
this. It is possible to have several devices share a single parallel
|
|
port and it is safe to compile the corresponding drivers into the
|
|
kernel.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called de600.
|
|
|
|
config DE620
|
|
tristate "D-Link DE620 pocket adapter support"
|
|
depends on NET_POCKET && PARPORT
|
|
---help---
|
|
This is a network (Ethernet) device which attaches to your parallel
|
|
port. Read <file:Documentation/networking/DLINK.txt> as well as the
|
|
Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>, if you want to use
|
|
this. It is possible to have several devices share a single parallel
|
|
port and it is safe to compile the corresponding drivers into the
|
|
kernel.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called de620.
|
|
|
|
config SGISEEQ
|
|
tristate "SGI Seeq ethernet controller support"
|
|
depends on SGI_HAS_SEEQ
|
|
help
|
|
Say Y here if you have an Seeq based Ethernet network card. This is
|
|
used in many Silicon Graphics machines.
|
|
|
|
config DECLANCE
|
|
tristate "DEC LANCE ethernet controller support"
|
|
depends on MACH_DECSTATION
|
|
select CRC32
|
|
help
|
|
This driver is for the series of Ethernet controllers produced by
|
|
DEC (now Compaq) based on the AMD Lance chipset, including the
|
|
DEPCA series. (This chipset is better known via the NE2100 cards.)
|
|
|
|
config 68360_ENET
|
|
bool "Motorola 68360 ethernet controller"
|
|
depends on M68360
|
|
help
|
|
Say Y here if you want to use the built-in ethernet controller of
|
|
the Motorola 68360 processor.
|
|
|
|
config FEC
|
|
bool "FEC ethernet controller (of ColdFire CPUs)"
|
|
depends on M523x || M527x || M5272 || M528x || M520x
|
|
help
|
|
Say Y here if you want to use the built-in 10/100 Fast ethernet
|
|
controller on some Motorola ColdFire processors.
|
|
|
|
config FEC2
|
|
bool "Second FEC ethernet controller (on some ColdFire CPUs)"
|
|
depends on FEC
|
|
help
|
|
Say Y here if you want to use the second built-in 10/100 Fast
|
|
ethernet controller on some Motorola ColdFire processors.
|
|
|
|
config FEC_MPC52xx
|
|
tristate "MPC52xx FEC driver"
|
|
depends on PPC_MERGE && PPC_MPC52xx && PPC_BESTCOMM_FEC
|
|
select CRC32
|
|
select PHYLIB
|
|
---help---
|
|
This option enables support for the MPC5200's on-chip
|
|
Fast Ethernet Controller
|
|
If compiled as module, it will be called 'fec_mpc52xx.ko'.
|
|
|
|
config FEC_MPC52xx_MDIO
|
|
bool "MPC52xx FEC MDIO bus driver"
|
|
depends on FEC_MPC52xx
|
|
default y
|
|
---help---
|
|
The MPC5200's FEC can connect to the Ethernet either with
|
|
an external MII PHY chip or 10 Mbps 7-wire interface
|
|
(Motorola? industry standard).
|
|
If your board uses an external PHY connected to FEC, enable this.
|
|
If not sure, enable.
|
|
If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.
|
|
|
|
config NE_H8300
|
|
tristate "NE2000 compatible support for H8/300"
|
|
depends on H8300
|
|
help
|
|
Say Y here if you want to use the NE2000 compatible
|
|
controller on the Renesas H8/300 processor.
|
|
|
|
config ATL2
|
|
tristate "Atheros L2 Fast Ethernet support"
|
|
depends on PCI
|
|
select CRC32
|
|
select MII
|
|
help
|
|
This driver supports the Atheros L2 fast ethernet adapter.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called atl2.
|
|
|
|
source "drivers/net/fs_enet/Kconfig"
|
|
|
|
endif # NET_ETHERNET
|
|
|
|
#
|
|
# Gigabit Ethernet
|
|
#
|
|
|
|
menuconfig NETDEV_1000
|
|
bool "Ethernet (1000 Mbit)"
|
|
depends on !UML
|
|
default y
|
|
---help---
|
|
Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
|
|
type of Local Area Network (LAN) in universities and companies.
|
|
|
|
Say Y here to get to see options for Gigabit Ethernet drivers.
|
|
This option alone does not add any kernel code.
|
|
Note that drivers supporting both 100 and 1000 MBit may be listed
|
|
under "Ethernet (10 or 100MBit)" instead.
|
|
|
|
If you say N, all options in this submenu will be skipped and disabled.
|
|
|
|
if NETDEV_1000
|
|
|
|
config ACENIC
|
|
tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
|
|
depends on PCI
|
|
---help---
|
|
Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear
|
|
GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet
|
|
adapter. The driver allows for using the Jumbo Frame option (9000
|
|
bytes/frame) however it requires that your switches can handle this
|
|
as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig
|
|
line.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called acenic.
|
|
|
|
config ACENIC_OMIT_TIGON_I
|
|
bool "Omit support for old Tigon I based AceNICs"
|
|
depends on ACENIC
|
|
help
|
|
Say Y here if you only have Tigon II based AceNICs and want to leave
|
|
out support for the older Tigon I based cards which are no longer
|
|
being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B
|
|
version)). This will reduce the size of the driver object by
|
|
app. 100KB. If you are not sure whether your card is a Tigon I or a
|
|
Tigon II, say N here.
|
|
|
|
The safe and default value for this is N.
|
|
|
|
config DL2K
|
|
tristate "DL2000/TC902x-based Gigabit Ethernet support"
|
|
depends on PCI
|
|
select CRC32
|
|
help
|
|
This driver supports DL2000/TC902x-based Gigabit ethernet cards,
|
|
which includes
|
|
D-Link DGE-550T Gigabit Ethernet Adapter.
|
|
D-Link DL2000-based Gigabit Ethernet Adapter.
|
|
Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called dl2k.
|
|
|
|
config E1000
|
|
tristate "Intel(R) PRO/1000 Gigabit Ethernet support"
|
|
depends on PCI
|
|
---help---
|
|
This driver supports Intel(R) PRO/1000 gigabit ethernet family of
|
|
adapters. For more information on how to identify your adapter, go
|
|
to the Adapter & Driver ID Guide at:
|
|
|
|
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
|
|
|
|
For general information and support, go to the Intel support
|
|
website at:
|
|
|
|
<http://support.intel.com>
|
|
|
|
More specific information on configuring the driver is in
|
|
<file:Documentation/networking/e1000.txt>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called e1000.
|
|
|
|
config E1000_DISABLE_PACKET_SPLIT
|
|
bool "Disable Packet Split for PCI express adapters"
|
|
depends on E1000
|
|
help
|
|
Say Y here if you want to use the legacy receive path for PCI express
|
|
hardware.
|
|
|
|
If in doubt, say N.
|
|
|
|
config E1000E
|
|
tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
|
|
depends on PCI && (!SPARC32 || BROKEN)
|
|
---help---
|
|
This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
|
|
ethernet family of adapters. For PCI or PCI-X e1000 adapters,
|
|
use the regular e1000 driver For more information on how to
|
|
identify your adapter, go to the Adapter & Driver ID Guide at:
|
|
|
|
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
|
|
|
|
For general information and support, go to the Intel support
|
|
website at:
|
|
|
|
<http://support.intel.com>
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called e1000e.
|
|
|
|
config IP1000
|
|
tristate "IP1000 Gigabit Ethernet support"
|
|
depends on PCI && EXPERIMENTAL
|
|
select MII
|
|
---help---
|
|
This driver supports IP1000 gigabit Ethernet cards.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called ipg. This is recommended.
|
|
|
|
config IGB
|
|
tristate "Intel(R) 82575 PCI-Express Gigabit Ethernet support"
|
|
depends on PCI
|
|
---help---
|
|
This driver supports Intel(R) 82575 gigabit ethernet family of
|
|
adapters. For more information on how to identify your adapter, go
|
|
to the Adapter & Driver ID Guide at:
|
|
|
|
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
|
|
|
|
For general information and support, go to the Intel support
|
|
website at:
|
|
|
|
<http://support.intel.com>
|
|
|
|
More specific information on configuring the driver is in
|
|
<file:Documentation/networking/e1000.txt>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called igb.
|
|
|
|
config IGB_LRO
|
|
bool "Use software LRO"
|
|
depends on IGB && INET
|
|
select INET_LRO
|
|
---help---
|
|
Say Y here if you want to use large receive offload.
|
|
|
|
If in doubt, say N.
|
|
|
|
source "drivers/net/ixp2000/Kconfig"
|
|
|
|
config MYRI_SBUS
|
|
tristate "MyriCOM Gigabit Ethernet support"
|
|
depends on SBUS
|
|
help
|
|
This driver supports MyriCOM Sbus gigabit Ethernet cards.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called myri_sbus. This is recommended.
|
|
|
|
config NS83820
|
|
tristate "National Semiconductor DP83820 support"
|
|
depends on PCI
|
|
help
|
|
This is a driver for the National Semiconductor DP83820 series
|
|
of gigabit ethernet MACs. Cards using this chipset include
|
|
the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
|
|
SOHO-GA2000T, SOHO-GA2500T. The driver supports the use of
|
|
zero copy.
|
|
|
|
config HAMACHI
|
|
tristate "Packet Engines Hamachi GNIC-II support"
|
|
depends on PCI
|
|
select MII
|
|
help
|
|
If you have a Gigabit Ethernet card of this type, say Y and read
|
|
the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
To compile this driver as a module, choose M here. The module will be
|
|
called hamachi.
|
|
|
|
config YELLOWFIN
|
|
tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
|
|
depends on PCI && EXPERIMENTAL
|
|
select CRC32
|
|
---help---
|
|
Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
|
|
adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
|
|
used by the Beowulf Linux cluster project. See
|
|
<http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
|
|
information about this driver in particular and Beowulf in general.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called yellowfin. This is recommended.
|
|
|
|
config R8169
|
|
tristate "Realtek 8169 gigabit ethernet support"
|
|
depends on PCI
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called r8169. This is recommended.
|
|
|
|
config R8169_VLAN
|
|
bool "VLAN support"
|
|
depends on R8169 && VLAN_8021Q
|
|
---help---
|
|
Say Y here for the r8169 driver to support the functions required
|
|
by the kernel 802.1Q code.
|
|
|
|
If in doubt, say Y.
|
|
|
|
config SB1250_MAC
|
|
tristate "SB1250 Gigabit Ethernet support"
|
|
depends on SIBYTE_SB1xxx_SOC
|
|
select PHYLIB
|
|
---help---
|
|
This driver supports Gigabit Ethernet interfaces based on the
|
|
Broadcom SiByte family of System-On-a-Chip parts. They include
|
|
the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
|
|
and BCM1480 chips.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sb1250-mac.
|
|
|
|
config SIS190
|
|
tristate "SiS190/SiS191 gigabit ethernet support"
|
|
depends on PCI
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
|
|
a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
|
|
appear in lan on motherboard designs which are based on SiS 965
|
|
and SiS 966 south bridge.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sis190. This is recommended.
|
|
|
|
config SKGE
|
|
tristate "New SysKonnect GigaEthernet support"
|
|
depends on PCI
|
|
select CRC32
|
|
---help---
|
|
This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
|
|
and related Gigabit Ethernet adapters. It is a new smaller driver
|
|
with better performance and more complete ethtool support.
|
|
|
|
It does not support the link failover and network management
|
|
features that "portable" vendor supplied sk98lin driver does.
|
|
|
|
This driver supports adapters based on the original Yukon chipset:
|
|
Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
|
|
Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
|
|
|
|
It does not support the newer Yukon2 chipset: a separate driver,
|
|
sky2, is provided for Yukon2-based adapters.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called skge. This is recommended.
|
|
|
|
config SKGE_DEBUG
|
|
bool "Debugging interface"
|
|
depends on SKGE && DEBUG_FS
|
|
help
|
|
This option adds the ability to dump driver state for debugging.
|
|
The file debugfs/skge/ethX displays the state of the internal
|
|
transmit and receive rings.
|
|
|
|
If unsure, say N.
|
|
|
|
config SKY2
|
|
tristate "SysKonnect Yukon2 support"
|
|
depends on PCI
|
|
select CRC32
|
|
---help---
|
|
This driver supports Gigabit Ethernet adapters based on the
|
|
Marvell Yukon 2 chipset:
|
|
Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
|
|
88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
|
|
|
|
There is companion driver for the older Marvell Yukon and
|
|
Genesis based adapters: skge.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called sky2. This is recommended.
|
|
|
|
config SKY2_DEBUG
|
|
bool "Debugging interface"
|
|
depends on SKY2 && DEBUG_FS
|
|
help
|
|
This option adds the ability to dump driver state for debugging.
|
|
The file debugfs/sky2/ethX displays the state of the internal
|
|
transmit and receive rings.
|
|
|
|
If unsure, say N.
|
|
|
|
config VIA_VELOCITY
|
|
tristate "VIA Velocity support"
|
|
depends on PCI
|
|
select CRC32
|
|
select CRC_CCITT
|
|
select MII
|
|
help
|
|
If you have a VIA "Velocity" based network card say Y here.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called via-velocity.
|
|
|
|
config TIGON3
|
|
tristate "Broadcom Tigon3 support"
|
|
depends on PCI
|
|
select PHYLIB
|
|
help
|
|
This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called tg3. This is recommended.
|
|
|
|
config BNX2
|
|
tristate "Broadcom NetXtremeII support"
|
|
depends on PCI
|
|
select CRC32
|
|
select ZLIB_INFLATE
|
|
help
|
|
This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called bnx2. This is recommended.
|
|
|
|
config SPIDER_NET
|
|
tristate "Spider Gigabit Ethernet driver"
|
|
depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
|
|
select FW_LOADER
|
|
help
|
|
This driver supports the Gigabit Ethernet chips present on the
|
|
Cell Processor-Based Blades from IBM.
|
|
|
|
config TSI108_ETH
|
|
tristate "Tundra TSI108 gigabit Ethernet support"
|
|
depends on TSI108_BRIDGE
|
|
help
|
|
This driver supports Tundra TSI108 gigabit Ethernet ports.
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called tsi108_eth.
|
|
|
|
config GELIC_NET
|
|
tristate "PS3 Gigabit Ethernet driver"
|
|
depends on PPC_PS3
|
|
select PS3_SYS_MANAGER
|
|
help
|
|
This driver supports the network device on the PS3 game
|
|
console. This driver has built-in support for Ethernet.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ps3_gelic.
|
|
|
|
config GELIC_WIRELESS
|
|
bool "PS3 Wireless support"
|
|
depends on GELIC_NET
|
|
select WIRELESS_EXT
|
|
help
|
|
This option adds the support for the wireless feature of PS3.
|
|
If you have the wireless-less model of PS3 or have no plan to
|
|
use wireless feature, disabling this option saves memory. As
|
|
the driver automatically distinguishes the models, you can
|
|
safely enable this option even if you have a wireless-less model.
|
|
|
|
config GELIC_WIRELESS_OLD_PSK_INTERFACE
|
|
bool "PS3 Wireless private PSK interface (OBSOLETE)"
|
|
depends on GELIC_WIRELESS
|
|
help
|
|
This option retains the obsolete private interface to pass
|
|
the PSK from user space programs to the driver. The PSK
|
|
stands for 'Pre Shared Key' and is used for WPA[2]-PSK
|
|
(WPA-Personal) environment.
|
|
If WPA[2]-PSK is used and you need to use old programs that
|
|
support only this old interface, say Y. Otherwise N.
|
|
|
|
If unsure, say N.
|
|
|
|
config GIANFAR
|
|
tristate "Gianfar Ethernet"
|
|
depends on FSL_SOC
|
|
select PHYLIB
|
|
select CRC32
|
|
help
|
|
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
|
|
and MPC86xx family of chips, and the FEC on the 8540.
|
|
|
|
config UCC_GETH
|
|
tristate "Freescale QE Gigabit Ethernet"
|
|
depends on QUICC_ENGINE
|
|
select PHYLIB
|
|
help
|
|
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
|
|
which is available on some Freescale SOCs.
|
|
|
|
config UGETH_MAGIC_PACKET
|
|
bool "Magic Packet detection support"
|
|
depends on UCC_GETH
|
|
|
|
config UGETH_FILTERING
|
|
bool "Mac address filtering support"
|
|
depends on UCC_GETH
|
|
|
|
config UGETH_TX_ON_DEMAND
|
|
bool "Transmit on Demand support"
|
|
depends on UCC_GETH
|
|
|
|
config MV643XX_ETH
|
|
tristate "Marvell Discovery (643XX) and Orion ethernet support"
|
|
depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
|
|
select PHYLIB
|
|
help
|
|
This driver supports the gigabit ethernet MACs in the
|
|
Marvell Discovery PPC/MIPS chipset family (MV643XX) and
|
|
in the Marvell Orion ARM SoC family.
|
|
|
|
Some boards that use the Discovery chipset are the Momenco
|
|
Ocelot C and Jaguar ATX and Pegasos II.
|
|
|
|
config QLA3XXX
|
|
tristate "QLogic QLA3XXX Network Driver Support"
|
|
depends on PCI
|
|
help
|
|
This driver supports QLogic ISP3XXX gigabit Ethernet cards.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called qla3xxx.
|
|
|
|
config ATL1
|
|
tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
|
|
depends on PCI && EXPERIMENTAL
|
|
select CRC32
|
|
select MII
|
|
help
|
|
This driver supports the Attansic L1 gigabit ethernet adapter.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called atl1.
|
|
|
|
config ATL1E
|
|
tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
|
|
depends on PCI && EXPERIMENTAL
|
|
select CRC32
|
|
select MII
|
|
help
|
|
This driver supports the Atheros L1E gigabit ethernet adapter.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called atl1e.
|
|
|
|
config JME
|
|
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
|
|
depends on PCI
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
This driver supports the PCI-Express gigabit ethernet adapters
|
|
based on JMicron JMC250 chipset.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called jme.
|
|
|
|
endif # NETDEV_1000
|
|
|
|
#
|
|
# 10 Gigabit Ethernet
|
|
#
|
|
|
|
menuconfig NETDEV_10000
|
|
bool "Ethernet (10000 Mbit)"
|
|
depends on !UML
|
|
default y
|
|
---help---
|
|
Say Y here to get to see options for 10 Gigabit Ethernet drivers.
|
|
This option alone does not add any kernel code.
|
|
|
|
If you say N, all options in this submenu will be skipped and disabled.
|
|
|
|
if NETDEV_10000
|
|
|
|
config CHELSIO_T1
|
|
tristate "Chelsio 10Gb Ethernet support"
|
|
depends on PCI
|
|
select CRC32
|
|
help
|
|
This driver supports Chelsio gigabit and 10-gigabit
|
|
Ethernet cards. More information about adapter features and
|
|
performance tuning is in <file:Documentation/networking/cxgb.txt>.
|
|
|
|
For general information about Chelsio and our products, visit
|
|
our website at <http://www.chelsio.com>.
|
|
|
|
For customer support, please visit our customer support page at
|
|
<http://www.chelsio.com/support.htm>.
|
|
|
|
Please send feedback to <linux-bugs@chelsio.com>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called cxgb.
|
|
|
|
config CHELSIO_T1_1G
|
|
bool "Chelsio gigabit Ethernet support"
|
|
depends on CHELSIO_T1
|
|
help
|
|
Enables support for Chelsio's gigabit Ethernet PCI cards. If you
|
|
are using only 10G cards say 'N' here.
|
|
|
|
config CHELSIO_T3
|
|
tristate "Chelsio Communications T3 10Gb Ethernet support"
|
|
depends on PCI && INET
|
|
select FW_LOADER
|
|
select INET_LRO
|
|
help
|
|
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
|
|
adapters.
|
|
|
|
For general information about Chelsio and our products, visit
|
|
our website at <http://www.chelsio.com>.
|
|
|
|
For customer support, please visit our customer support page at
|
|
<http://www.chelsio.com/support.htm>.
|
|
|
|
Please send feedback to <linux-bugs@chelsio.com>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called cxgb3.
|
|
|
|
config EHEA
|
|
tristate "eHEA Ethernet support"
|
|
depends on IBMEBUS && INET && SPARSEMEM
|
|
select INET_LRO
|
|
---help---
|
|
This driver supports the IBM pSeries eHEA ethernet adapter.
|
|
|
|
To compile the driver as a module, choose M here. The module
|
|
will be called ehea.
|
|
|
|
config ENIC
|
|
tristate "E, the Cisco 10G Ethernet NIC"
|
|
depends on PCI && INET
|
|
select INET_LRO
|
|
help
|
|
This enables the support for the Cisco 10G Ethernet card.
|
|
|
|
config IXGBE
|
|
tristate "Intel(R) 10GbE PCI Express adapters support"
|
|
depends on PCI && INET
|
|
select INET_LRO
|
|
select INTEL_IOATDMA
|
|
---help---
|
|
This driver supports Intel(R) 10GbE PCI Express family of
|
|
adapters. For more information on how to identify your adapter, go
|
|
to the Adapter & Driver ID Guide at:
|
|
|
|
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
|
|
|
|
For general information and support, go to the Intel support
|
|
website at:
|
|
|
|
<http://support.intel.com>
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ixgbe.
|
|
|
|
config IXGB
|
|
tristate "Intel(R) PRO/10GbE support"
|
|
depends on PCI
|
|
---help---
|
|
This driver supports Intel(R) PRO/10GbE family of adapters for
|
|
PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
|
|
instead. For more information on how to identify your adapter, go
|
|
to the Adapter & Driver ID Guide at:
|
|
|
|
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
|
|
|
|
For general information and support, go to the Intel support
|
|
website at:
|
|
|
|
<http://support.intel.com>
|
|
|
|
More specific information on configuring the driver is in
|
|
<file:Documentation/networking/ixgb.txt>.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ixgb.
|
|
|
|
config S2IO
|
|
tristate "S2IO 10Gbe XFrame NIC"
|
|
depends on PCI
|
|
---help---
|
|
This driver supports the 10Gbe XFrame NIC of S2IO.
|
|
More specific information on configuring the driver is in
|
|
<file:Documentation/networking/s2io.txt>.
|
|
|
|
config MYRI10GE
|
|
tristate "Myricom Myri-10G Ethernet support"
|
|
depends on PCI && INET
|
|
select FW_LOADER
|
|
select CRC32
|
|
select INET_LRO
|
|
select INTEL_IOATDMA
|
|
---help---
|
|
This driver supports Myricom Myri-10G Dual Protocol interface in
|
|
Ethernet mode. If the eeprom on your board is not recent enough,
|
|
you will need a newer firmware image.
|
|
You may get this image or more information, at:
|
|
|
|
<http://www.myri.com/scs/download-Myri10GE.html>
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called myri10ge.
|
|
|
|
config NETXEN_NIC
|
|
tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
|
|
depends on PCI
|
|
help
|
|
This enables the support for NetXen's Gigabit Ethernet card.
|
|
|
|
config NIU
|
|
tristate "Sun Neptune 10Gbit Ethernet support"
|
|
depends on PCI
|
|
help
|
|
This enables support for cards based upon Sun's
|
|
Neptune chipset.
|
|
|
|
config PASEMI_MAC
|
|
tristate "PA Semi 1/10Gbit MAC"
|
|
depends on PPC_PASEMI && PCI
|
|
select PHYLIB
|
|
select INET_LRO
|
|
help
|
|
This driver supports the on-chip 1/10Gbit Ethernet controller on
|
|
PA Semi's PWRficient line of chips.
|
|
|
|
config MLX4_CORE
|
|
tristate
|
|
depends on PCI
|
|
default n
|
|
|
|
config MLX4_DEBUG
|
|
bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED)
|
|
depends on MLX4_CORE
|
|
default y
|
|
---help---
|
|
This option causes debugging code to be compiled into the
|
|
mlx4_core driver. The output can be turned on via the
|
|
debug_level module parameter (which can also be set after
|
|
the driver is loaded through sysfs).
|
|
|
|
config TEHUTI
|
|
tristate "Tehuti Networks 10G Ethernet"
|
|
depends on PCI
|
|
help
|
|
Tehuti Networks 10G Ethernet NIC
|
|
|
|
config BNX2X
|
|
tristate "Broadcom NetXtremeII 10Gb support"
|
|
depends on PCI
|
|
select ZLIB_INFLATE
|
|
select LIBCRC32C
|
|
help
|
|
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called bnx2x. This is recommended.
|
|
|
|
config QLGE
|
|
tristate "QLogic QLGE 10Gb Ethernet Driver Support"
|
|
depends on PCI
|
|
help
|
|
This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called qlge.
|
|
|
|
source "drivers/net/sfc/Kconfig"
|
|
|
|
endif # NETDEV_10000
|
|
|
|
source "drivers/net/tokenring/Kconfig"
|
|
|
|
source "drivers/net/wireless/Kconfig"
|
|
|
|
source "drivers/net/usb/Kconfig"
|
|
|
|
source "drivers/net/pcmcia/Kconfig"
|
|
|
|
source "drivers/net/wan/Kconfig"
|
|
|
|
source "drivers/atm/Kconfig"
|
|
|
|
source "drivers/s390/net/Kconfig"
|
|
|
|
config XEN_NETDEV_FRONTEND
|
|
tristate "Xen network device frontend driver"
|
|
depends on XEN
|
|
default y
|
|
help
|
|
The network device frontend driver allows the kernel to
|
|
access network devices exported exported by a virtual
|
|
machine containing a physical network device driver. The
|
|
frontend driver is intended for unprivileged guest domains;
|
|
if you are compiling a kernel for a Xen guest, you almost
|
|
certainly want to enable this.
|
|
|
|
config ISERIES_VETH
|
|
tristate "iSeries Virtual Ethernet driver support"
|
|
depends on PPC_ISERIES
|
|
|
|
config RIONET
|
|
tristate "RapidIO Ethernet over messaging driver support"
|
|
depends on RAPIDIO
|
|
|
|
config RIONET_TX_SIZE
|
|
int "Number of outbound queue entries"
|
|
depends on RIONET
|
|
default "128"
|
|
|
|
config RIONET_RX_SIZE
|
|
int "Number of inbound queue entries"
|
|
depends on RIONET
|
|
default "128"
|
|
|
|
config FDDI
|
|
bool "FDDI driver support"
|
|
depends on (PCI || EISA || TC)
|
|
help
|
|
Fiber Distributed Data Interface is a high speed local area network
|
|
design; essentially a replacement for high speed Ethernet. FDDI can
|
|
run over copper or fiber. If you are connected to such a network and
|
|
want a driver for the FDDI card in your computer, say Y here (and
|
|
then also Y to the driver for your FDDI card, below). Most people
|
|
will say N.
|
|
|
|
config DEFXX
|
|
tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
|
|
depends on FDDI && (PCI || EISA || TC)
|
|
---help---
|
|
This is support for the DIGITAL series of TURBOchannel (DEFTA),
|
|
EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
|
|
to a local FDDI network.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called defxx. If unsure, say N.
|
|
|
|
config DEFXX_MMIO
|
|
bool
|
|
prompt "Use MMIO instead of PIO" if PCI || EISA
|
|
depends on DEFXX
|
|
default n if PCI || EISA
|
|
default y
|
|
---help---
|
|
This instructs the driver to use EISA or PCI memory-mapped I/O
|
|
(MMIO) as appropriate instead of programmed I/O ports (PIO).
|
|
Enabling this gives an improvement in processing time in parts
|
|
of the driver, but it may cause problems with EISA (DEFEA)
|
|
adapters. TURBOchannel does not have the concept of I/O ports,
|
|
so MMIO is always used for these (DEFTA) adapters.
|
|
|
|
If unsure, say N.
|
|
|
|
config SKFP
|
|
tristate "SysKonnect FDDI PCI support"
|
|
depends on FDDI && PCI
|
|
select BITREVERSE
|
|
---help---
|
|
Say Y here if you have a SysKonnect FDDI PCI adapter.
|
|
The following adapters are supported by this driver:
|
|
- SK-5521 (SK-NET FDDI-UP)
|
|
- SK-5522 (SK-NET FDDI-UP DAS)
|
|
- SK-5541 (SK-NET FDDI-FP)
|
|
- SK-5543 (SK-NET FDDI-LP)
|
|
- SK-5544 (SK-NET FDDI-LP DAS)
|
|
- SK-5821 (SK-NET FDDI-UP64)
|
|
- SK-5822 (SK-NET FDDI-UP64 DAS)
|
|
- SK-5841 (SK-NET FDDI-FP64)
|
|
- SK-5843 (SK-NET FDDI-LP64)
|
|
- SK-5844 (SK-NET FDDI-LP64 DAS)
|
|
- Netelligent 100 FDDI DAS Fibre SC
|
|
- Netelligent 100 FDDI SAS Fibre SC
|
|
- Netelligent 100 FDDI DAS UTP
|
|
- Netelligent 100 FDDI SAS UTP
|
|
- Netelligent 100 FDDI SAS Fibre MIC
|
|
|
|
Read <file:Documentation/networking/skfp.txt> for information about
|
|
the driver.
|
|
|
|
Questions concerning this driver can be addressed to:
|
|
<linux@syskonnect.de>
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called skfp. This is recommended.
|
|
|
|
config HIPPI
|
|
bool "HIPPI driver support (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL && INET && PCI
|
|
help
|
|
HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
|
|
1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
|
|
can run over copper (25m) or fiber (300m on multi-mode or 10km on
|
|
single-mode). HIPPI networks are commonly used for clusters and to
|
|
connect to super computers. If you are connected to a HIPPI network
|
|
and have a HIPPI network card in your computer that you want to use
|
|
under Linux, say Y here (you must also remember to enable the driver
|
|
for your HIPPI card below). Most people will say N here.
|
|
|
|
config ROADRUNNER
|
|
tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
|
|
depends on HIPPI && PCI
|
|
help
|
|
Say Y here if this is your PCI HIPPI network card.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called rrunner. If unsure, say N.
|
|
|
|
config ROADRUNNER_LARGE_RINGS
|
|
bool "Use large TX/RX rings (EXPERIMENTAL)"
|
|
depends on ROADRUNNER
|
|
help
|
|
If you say Y here, the RoadRunner driver will preallocate up to 2 MB
|
|
of additional memory to allow for fastest operation, both for
|
|
transmitting and receiving. This memory cannot be used by any other
|
|
kernel code or by user space programs. Say Y here only if you have
|
|
the memory.
|
|
|
|
config PLIP
|
|
tristate "PLIP (parallel port) support"
|
|
depends on PARPORT
|
|
---help---
|
|
PLIP (Parallel Line Internet Protocol) is used to create a
|
|
reasonably fast mini network consisting of two (or, rarely, more)
|
|
local machines. A PLIP link from a Linux box is a popular means to
|
|
install a Linux distribution on a machine which doesn't have a
|
|
CD-ROM drive (a minimal system has to be transferred with floppies
|
|
first). The kernels on both machines need to have this PLIP option
|
|
enabled for this to work.
|
|
|
|
The PLIP driver has two modes, mode 0 and mode 1. The parallel
|
|
ports (the connectors at the computers with 25 holes) are connected
|
|
with "null printer" or "Turbo Laplink" cables which can transmit 4
|
|
bits at a time (mode 0) or with special PLIP cables, to be used on
|
|
bidirectional parallel ports only, which can transmit 8 bits at a
|
|
time (mode 1); you can find the wiring of these cables in
|
|
<file:Documentation/networking/PLIP.txt>. The cables can be up to
|
|
15m long. Mode 0 works also if one of the machines runs DOS/Windows
|
|
and has some PLIP software installed, e.g. the Crynwr PLIP packet
|
|
driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
|
|
and winsock or NCSA's telnet.
|
|
|
|
If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
|
|
as the NET-3-HOWTO, both available from
|
|
<http://www.tldp.org/docs.html#howto>. Note that the PLIP
|
|
protocol has been changed and this PLIP driver won't work together
|
|
with the PLIP support in Linux versions 1.0.x. This option enlarges
|
|
your kernel by about 8 KB.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called plip. If unsure, say Y or M, in case you buy
|
|
a laptop later.
|
|
|
|
config PPP
|
|
tristate "PPP (point-to-point protocol) support"
|
|
select SLHC
|
|
---help---
|
|
PPP (Point to Point Protocol) is a newer and better SLIP. It serves
|
|
the same purpose: sending Internet traffic over telephone (and other
|
|
serial) lines. Ask your access provider if they support it, because
|
|
otherwise you can't use it; most Internet access providers these
|
|
days support PPP rather than SLIP.
|
|
|
|
To use PPP, you need an additional program called pppd as described
|
|
in the PPP-HOWTO, available at
|
|
<http://www.tldp.org/docs.html#howto>. Make sure that you have
|
|
the version of pppd recommended in <file:Documentation/Changes>.
|
|
The PPP option enlarges your kernel by about 16 KB.
|
|
|
|
There are actually two versions of PPP: the traditional PPP for
|
|
asynchronous lines, such as regular analog phone lines, and
|
|
synchronous PPP which can be used over digital ISDN lines for
|
|
example. If you want to use PPP over phone lines or other
|
|
asynchronous serial lines, you need to say Y (or M) here and also to
|
|
the next option, "PPP support for async serial ports". For PPP over
|
|
synchronous lines, you should say Y (or M) here and to "Support
|
|
synchronous PPP", below.
|
|
|
|
If you said Y to "Version information on all symbols" above, then
|
|
you cannot compile the PPP driver into the kernel; you can then only
|
|
compile it as a module. To compile this driver as a module, choose M
|
|
here. The module will be called ppp_generic.
|
|
|
|
config PPP_MULTILINK
|
|
bool "PPP multilink support (EXPERIMENTAL)"
|
|
depends on PPP && EXPERIMENTAL
|
|
help
|
|
PPP multilink is a protocol (defined in RFC 1990) which allows you
|
|
to combine several (logical or physical) lines into one logical PPP
|
|
connection, so that you can utilize your full bandwidth.
|
|
|
|
This has to be supported at the other end as well and you need a
|
|
version of the pppd daemon which understands the multilink protocol.
|
|
|
|
If unsure, say N.
|
|
|
|
config PPP_FILTER
|
|
bool "PPP filtering"
|
|
depends on PPP
|
|
help
|
|
Say Y here if you want to be able to filter the packets passing over
|
|
PPP interfaces. This allows you to control which packets count as
|
|
activity (i.e. which packets will reset the idle timer or bring up
|
|
a demand-dialed link) and which packets are to be dropped entirely.
|
|
You need to say Y here if you wish to use the pass-filter and
|
|
active-filter options to pppd.
|
|
|
|
If unsure, say N.
|
|
|
|
config PPP_ASYNC
|
|
tristate "PPP support for async serial ports"
|
|
depends on PPP
|
|
select CRC_CCITT
|
|
---help---
|
|
Say Y (or M) here if you want to be able to use PPP over standard
|
|
asynchronous serial ports, such as COM1 or COM2 on a PC. If you use
|
|
a modem (not a synchronous or ISDN modem) to contact your ISP, you
|
|
need this option.
|
|
|
|
To compile this driver as a module, choose M here.
|
|
|
|
If unsure, say Y.
|
|
|
|
config PPP_SYNC_TTY
|
|
tristate "PPP support for sync tty ports"
|
|
depends on PPP
|
|
help
|
|
Say Y (or M) here if you want to be able to use PPP over synchronous
|
|
(HDLC) tty devices, such as the SyncLink adapter. These devices
|
|
are often used for high-speed leased lines like T1/E1.
|
|
|
|
To compile this driver as a module, choose M here.
|
|
|
|
config PPP_DEFLATE
|
|
tristate "PPP Deflate compression"
|
|
depends on PPP
|
|
select ZLIB_INFLATE
|
|
select ZLIB_DEFLATE
|
|
---help---
|
|
Support for the Deflate compression method for PPP, which uses the
|
|
Deflate algorithm (the same algorithm that gzip uses) to compress
|
|
each PPP packet before it is sent over the wire. The machine at the
|
|
other end of the PPP link (usually your ISP) has to support the
|
|
Deflate compression method as well for this to be useful. Even if
|
|
they don't support it, it is safe to say Y here.
|
|
|
|
To compile this driver as a module, choose M here.
|
|
|
|
config PPP_BSDCOMP
|
|
tristate "PPP BSD-Compress compression"
|
|
depends on PPP
|
|
---help---
|
|
Support for the BSD-Compress compression method for PPP, which uses
|
|
the LZW compression method to compress each PPP packet before it is
|
|
sent over the wire. The machine at the other end of the PPP link
|
|
(usually your ISP) has to support the BSD-Compress compression
|
|
method as well for this to be useful. Even if they don't support it,
|
|
it is safe to say Y here.
|
|
|
|
The PPP Deflate compression method ("PPP Deflate compression",
|
|
above) is preferable to BSD-Compress, because it compresses better
|
|
and is patent-free.
|
|
|
|
Note that the BSD compression code will always be compiled as a
|
|
module; it is called bsd_comp and will show up in the directory
|
|
modules once you have said "make modules". If unsure, say N.
|
|
|
|
config PPP_MPPE
|
|
tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
|
|
depends on PPP && EXPERIMENTAL
|
|
select CRYPTO
|
|
select CRYPTO_SHA1
|
|
select CRYPTO_ARC4
|
|
select CRYPTO_ECB
|
|
---help---
|
|
Support for the MPPE Encryption protocol, as employed by the
|
|
Microsoft Point-to-Point Tunneling Protocol.
|
|
|
|
See http://pptpclient.sourceforge.net/ for information on
|
|
configuring PPTP clients and servers to utilize this method.
|
|
|
|
config PPPOE
|
|
tristate "PPP over Ethernet (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL && PPP
|
|
help
|
|
Support for PPP over Ethernet.
|
|
|
|
This driver requires the latest version of pppd from the CVS
|
|
repository at cvs.samba.org. Alternatively, see the
|
|
RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
|
|
which contains instruction on how to use this driver (under
|
|
the heading "Kernel mode PPPoE").
|
|
|
|
config PPPOATM
|
|
tristate "PPP over ATM"
|
|
depends on ATM && PPP
|
|
help
|
|
Support PPP (Point to Point Protocol) encapsulated in ATM frames.
|
|
This implementation does not yet comply with section 8 of RFC2364,
|
|
which can lead to bad results if the ATM peer loses state and
|
|
changes its encapsulation unilaterally.
|
|
|
|
config PPPOL2TP
|
|
tristate "PPP over L2TP (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL && PPP && INET
|
|
help
|
|
Support for PPP-over-L2TP socket family. L2TP is a protocol
|
|
used by ISPs and enterprises to tunnel PPP traffic over UDP
|
|
tunnels. L2TP is replacing PPTP for VPN uses.
|
|
|
|
This kernel component handles only L2TP data packets: a
|
|
userland daemon handles L2TP the control protocol (tunnel
|
|
and session setup). One such daemon is OpenL2TP
|
|
(http://openl2tp.sourceforge.net/).
|
|
|
|
config SLIP
|
|
tristate "SLIP (serial line) support"
|
|
---help---
|
|
Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
|
|
connect to your Internet service provider or to connect to some
|
|
other local Unix box or if you want to configure your Linux box as a
|
|
Slip/CSlip server for other people to dial in. SLIP (Serial Line
|
|
Internet Protocol) is a protocol used to send Internet traffic over
|
|
serial connections such as telephone lines or null modem cables;
|
|
nowadays, the protocol PPP is more commonly used for this same
|
|
purpose.
|
|
|
|
Normally, your access provider has to support SLIP in order for you
|
|
to be able to use it, but there is now a SLIP emulator called SLiRP
|
|
around (available from
|
|
<ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
|
|
allows you to use SLIP over a regular dial up shell connection. If
|
|
you plan to use SLiRP, make sure to say Y to CSLIP, below. The
|
|
NET-3-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>, explains how to
|
|
configure SLIP. Note that you don't need this option if you just
|
|
want to run term (term is a program which gives you almost full
|
|
Internet connectivity if you have a regular dial up shell account on
|
|
some Internet connected Unix computer. Read
|
|
<http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
|
|
support will enlarge your kernel by about 4 KB. If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called slip.
|
|
|
|
config SLIP_COMPRESSED
|
|
bool "CSLIP compressed headers"
|
|
depends on SLIP
|
|
select SLHC
|
|
---help---
|
|
This protocol is faster than SLIP because it uses compression on the
|
|
TCP/IP headers (not on the data itself), but it has to be supported
|
|
on both ends. Ask your access provider if you are not sure and
|
|
answer Y, just in case. You will still be able to use plain SLIP. If
|
|
you plan to use SLiRP, the SLIP emulator (available from
|
|
<ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
|
|
allows you to use SLIP over a regular dial up shell connection, you
|
|
definitely want to say Y here. The NET-3-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>, explains how to configure
|
|
CSLIP. This won't enlarge your kernel.
|
|
|
|
config SLHC
|
|
tristate
|
|
help
|
|
This option enables Van Jacobsen serial line header compression
|
|
routines.
|
|
|
|
config SLIP_SMART
|
|
bool "Keepalive and linefill"
|
|
depends on SLIP
|
|
help
|
|
Adds additional capabilities to the SLIP driver to support the
|
|
RELCOM line fill and keepalive monitoring. Ideal on poor quality
|
|
analogue lines.
|
|
|
|
config SLIP_MODE_SLIP6
|
|
bool "Six bit SLIP encapsulation"
|
|
depends on SLIP
|
|
help
|
|
Just occasionally you may need to run IP over hostile serial
|
|
networks that don't pass all control characters or are only seven
|
|
bit. Saying Y here adds an extra mode you can use with SLIP:
|
|
"slip6". In this mode, SLIP will only send normal ASCII symbols over
|
|
the serial device. Naturally, this has to be supported at the other
|
|
end of the link as well. It's good enough, for example, to run IP
|
|
over the async ports of a Camtec JNT Pad. If unsure, say N.
|
|
|
|
config NET_FC
|
|
bool "Fibre Channel driver support"
|
|
depends on SCSI && PCI
|
|
help
|
|
Fibre Channel is a high speed serial protocol mainly used to connect
|
|
large storage devices to the computer; it is compatible with and
|
|
intended to replace SCSI.
|
|
|
|
If you intend to use Fibre Channel, you need to have a Fibre channel
|
|
adaptor card in your computer; say Y here and to the driver for your
|
|
adaptor below. You also should have said Y to "SCSI support" and
|
|
"SCSI generic support".
|
|
|
|
config NETCONSOLE
|
|
tristate "Network console logging support (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL
|
|
---help---
|
|
If you want to log kernel messages over the network, enable this.
|
|
See <file:Documentation/networking/netconsole.txt> for details.
|
|
|
|
config NETCONSOLE_DYNAMIC
|
|
bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
|
|
depends on NETCONSOLE && SYSFS && EXPERIMENTAL
|
|
select CONFIGFS_FS
|
|
help
|
|
This option enables the ability to dynamically reconfigure target
|
|
parameters (interface, IP addresses, port numbers, MAC addresses)
|
|
at runtime through a userspace interface exported using configfs.
|
|
See <file:Documentation/networking/netconsole.txt> for details.
|
|
|
|
config NETPOLL
|
|
def_bool NETCONSOLE
|
|
|
|
config NETPOLL_TRAP
|
|
bool "Netpoll traffic trapping"
|
|
default n
|
|
depends on NETPOLL
|
|
|
|
config NET_POLL_CONTROLLER
|
|
def_bool NETPOLL
|
|
|
|
config VIRTIO_NET
|
|
tristate "Virtio network driver (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL && VIRTIO
|
|
---help---
|
|
This is the virtual network driver for virtio. It can be used with
|
|
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
|
|
|
|
endif # NETDEVICES
|