korg/linux
0
0
Fork 0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-12-13 22:14:20 +08:00
Code Issues Packages Projects Releases Wiki Activity
add279faeb
linux/drivers/usb/host/ehci-hub.c
Xu Yang dda4b60ed7 usb: ehci: add workaround for chipidea PORTSC.PEC bug 
Some NXP processor using chipidea IP has a bug when frame babble is
detected.

As per 4.15.1.1.1 Serial Bus Babble:
  A babble condition also exists if IN transaction is in progress at
High-speed SOF2 point. This is called frame babble. The host controller
must disable the port to which the frame babble is detected.

The USB controller has disabled the port (PE cleared) and has asserted
USBERRINT when frame babble is detected, but PEC is not asserted.
Therefore, the SW isn't aware that port has been disabled. Then the
SW keeps sending packets to this port, but all of the transfers will
fail.

This workaround will firstly assert PCD by SW when USBERRINT is detected
and then judge whether port change has really occurred or not by polling
roothub status. Because the PEC doesn't get asserted in our case, this
patch will also assert it by SW when specific conditions are satisfied.

Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230809024432.535160-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-09 14:16:06 +02:00

1223 lines
33 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2001-2004 by David Brownell
*/
/* this file is part of ehci-hcd.c */
/*-------------------------------------------------------------------------*/
/*
* EHCI Root Hub ... the nonsharable stuff
*
* Registers don't need cpu_to_le32, that happens transparently
*/
/*-------------------------------------------------------------------------*/
#define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)
#ifdef CONFIG_PM
static void unlink_empty_async_suspended(struct ehci_hcd *ehci);
static int persist_enabled_on_companion(struct usb_device *udev, void *unused)
{
return !udev->maxchild && udev->persist_enabled &&
udev->bus->root_hub->speed < USB_SPEED_HIGH;
}
/* After a power loss, ports that were owned by the companion must be
* reset so that the companion can still own them.
*/
static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
{
u32 __iomem *reg;
u32 status;
int port;
__le32 buf;
struct usb_hcd *hcd = ehci_to_hcd(ehci);
if (!ehci->owned_ports)
return;
/*
* USB 1.1 devices are mostly HIDs, which don't need to persist across
* suspends. If we ensure that none of our companion's devices have
* persist_enabled (by looking through all USB 1.1 buses in the system),
* we can skip this and avoid slowing resume down. Devices without
* persist will just get reenumerated shortly after resume anyway.
*/
if (!usb_for_each_dev(NULL, persist_enabled_on_companion))
return;
/* Make sure the ports are powered */
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (test_bit(port, &ehci->owned_ports)) {
reg = &ehci->regs->port_status[port];
status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
if (!(status & PORT_POWER))
ehci_port_power(ehci, port, true);
}
}
/* Give the connections some time to appear */
msleep(20);
spin_lock_irq(&ehci->lock);
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (test_bit(port, &ehci->owned_ports)) {
reg = &ehci->regs->port_status[port];
status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
/* Port already owned by companion? */
if (status & PORT_OWNER)
clear_bit(port, &ehci->owned_ports);
else if (test_bit(port, &ehci->companion_ports))
ehci_writel(ehci, status & ~PORT_PE, reg);
else {
spin_unlock_irq(&ehci->lock);
ehci_hub_control(hcd, SetPortFeature,
USB_PORT_FEAT_RESET, port + 1,
NULL, 0);
spin_lock_irq(&ehci->lock);
}
}
}
spin_unlock_irq(&ehci->lock);
if (!ehci->owned_ports)
return;
msleep(90); /* Wait for resets to complete */
spin_lock_irq(&ehci->lock);
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (test_bit(port, &ehci->owned_ports)) {
spin_unlock_irq(&ehci->lock);
ehci_hub_control(hcd, GetPortStatus,
0, port + 1,
(char *) &buf, sizeof(buf));
spin_lock_irq(&ehci->lock);
/* The companion should now own the port,
* but if something went wrong the port must not
* remain enabled.
*/
reg = &ehci->regs->port_status[port];
status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
if (status & PORT_OWNER)
ehci_writel(ehci, status | PORT_CSC, reg);
else {
ehci_dbg(ehci, "failed handover port %d: %x\n",
port + 1, status);
ehci_writel(ehci, status & ~PORT_PE, reg);
}
}
}
ehci->owned_ports = 0;
spin_unlock_irq(&ehci->lock);
}
static int ehci_port_change(struct ehci_hcd *ehci)
{
int i = HCS_N_PORTS(ehci->hcs_params);
/* First check if the controller indicates a change event */
if (ehci_readl(ehci, &ehci->regs->status) & STS_PCD)
return 1;
/*
* Not all controllers appear to update this while going from D3 to D0,
* so check the individual port status registers as well
*/
while (i--)
if (ehci_readl(ehci, &ehci->regs->port_status[i]) & PORT_CSC)
return 1;
return 0;
}
void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
bool suspending, bool do_wakeup)
{
int port;
u32 temp;
/* If remote wakeup is enabled for the root hub but disabled
* for the controller, we must adjust all the port wakeup flags
* when the controller is suspended or resumed. In all other
* cases they don't need to be changed.
*/
if (!ehci_to_hcd(ehci)->self.root_hub->do_remote_wakeup || do_wakeup)
return;
spin_lock_irq(&ehci->lock);
/* clear phy low-power mode before changing wakeup flags */
if (ehci->has_tdi_phy_lpm) {
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *hostpc_reg = &ehci->regs->hostpc[port];
temp = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp & ~HOSTPC_PHCD, hostpc_reg);
}
spin_unlock_irq(&ehci->lock);
msleep(5);
spin_lock_irq(&ehci->lock);
}
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status[port];
u32 t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
u32 t2 = t1 & ~PORT_WAKE_BITS;
/* If we are suspending the controller, clear the flags.
* If we are resuming the controller, set the wakeup flags.
*/
if (!suspending) {
if (t1 & PORT_CONNECT)
t2 |= PORT_WKOC_E | PORT_WKDISC_E;
else
t2 |= PORT_WKOC_E | PORT_WKCONN_E;
}
ehci_writel(ehci, t2, reg);
}
/* enter phy low-power mode again */
if (ehci->has_tdi_phy_lpm) {
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *hostpc_reg = &ehci->regs->hostpc[port];
temp = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp | HOSTPC_PHCD, hostpc_reg);
}
}
/* Does the root hub have a port wakeup pending? */
if (!suspending && ehci_port_change(ehci))
usb_hcd_resume_root_hub(ehci_to_hcd(ehci));
spin_unlock_irq(&ehci->lock);
}
EXPORT_SYMBOL_GPL(ehci_adjust_port_wakeup_flags);
static int ehci_bus_suspend (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int port;
int mask;
int changed;
bool fs_idle_delay;
ehci_dbg(ehci, "suspend root hub\n");
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
/* stop the schedules */
ehci_quiesce(ehci);
spin_lock_irq (&ehci->lock);
if (ehci->rh_state < EHCI_RH_RUNNING)
goto done;
/* Once the controller is stopped, port resumes that are already
* in progress won't complete. Hence if remote wakeup is enabled
* for the root hub and any ports are in the middle of a resume or
* remote wakeup, we must fail the suspend.
*/
if (hcd->self.root_hub->do_remote_wakeup) {
if (ehci->resuming_ports) {
spin_unlock_irq(&ehci->lock);
ehci_dbg(ehci, "suspend failed because a port is resuming\n");
return -EBUSY;
}
}
/* Unlike other USB host controller types, EHCI doesn't have
* any notion of "global" or bus-wide suspend. The driver has
* to manually suspend all the active unsuspended ports, and
* then manually resume them in the bus_resume() routine.
*/
ehci->bus_suspended = 0;
ehci->owned_ports = 0;
changed = 0;
fs_idle_delay = false;
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status [port];
u32 t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
u32 t2 = t1 & ~PORT_WAKE_BITS;
/* keep track of which ports we suspend */
if (t1 & PORT_OWNER)
set_bit(port, &ehci->owned_ports);
else if ((t1 & PORT_PE) && !(t1 & PORT_SUSPEND)) {
t2 |= PORT_SUSPEND;
set_bit(port, &ehci->bus_suspended);
}
/* enable remote wakeup on all ports, if told to do so */
if (hcd->self.root_hub->do_remote_wakeup) {
/* only enable appropriate wake bits, otherwise the
* hardware can not go phy low power mode. If a race
* condition happens here(connection change during bits
* set), the port change detection will finally fix it.
*/
if (t1 & PORT_CONNECT)
t2 |= PORT_WKOC_E | PORT_WKDISC_E;
else
t2 |= PORT_WKOC_E | PORT_WKCONN_E;
}
if (t1 != t2) {
/*
* On some controllers, Wake-On-Disconnect will
* generate false wakeup signals until the bus
* switches over to full-speed idle. For their
* sake, add a delay if we need one.
*/
if ((t2 & PORT_WKDISC_E) &&
ehci_port_speed(ehci, t2) ==
USB_PORT_STAT_HIGH_SPEED)
fs_idle_delay = true;
ehci_writel(ehci, t2, reg);
changed = 1;
}
}
spin_unlock_irq(&ehci->lock);
if (changed && ehci_has_fsl_susp_errata(ehci))
/*
* Wait for at least 10 millisecondes to ensure the controller
* enter the suspend status before initiating a port resume
* using the Force Port Resume bit (Not-EHCI compatible).
*/
usleep_range(10000, 20000);
if ((changed && ehci->has_tdi_phy_lpm) || fs_idle_delay) {
/*
* Wait for HCD to enter low-power mode or for the bus
* to switch to full-speed idle.
*/
usleep_range(5000, 5500);
}
if (changed && ehci->has_tdi_phy_lpm) {
spin_lock_irq(&ehci->lock);
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *hostpc_reg = &ehci->regs->hostpc[port];
u32 t3;
t3 = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, t3 | HOSTPC_PHCD, hostpc_reg);
t3 = ehci_readl(ehci, hostpc_reg);
ehci_dbg(ehci, "Port %d phy low-power mode %s\n",
port, (t3 & HOSTPC_PHCD) ?
"succeeded" : "failed");
}
spin_unlock_irq(&ehci->lock);
}
/* Apparently some devices need a >= 1-uframe delay here */
if (ehci->bus_suspended)
udelay(150);
/* turn off now-idle HC */
ehci_halt (ehci);
spin_lock_irq(&ehci->lock);
if (ehci->enabled_hrtimer_events & BIT(EHCI_HRTIMER_POLL_DEAD))
ehci_handle_controller_death(ehci);
if (ehci->rh_state != EHCI_RH_RUNNING)
goto done;
ehci->rh_state = EHCI_RH_SUSPENDED;
unlink_empty_async_suspended(ehci);
/* Some Synopsys controllers mistakenly leave IAA turned on */
ehci_writel(ehci, STS_IAA, &ehci->regs->status);
/* Any IAA cycle that started before the suspend is now invalid */
end_iaa_cycle(ehci);
ehci_handle_start_intr_unlinks(ehci);
ehci_handle_intr_unlinks(ehci);
end_free_itds(ehci);
/* allow remote wakeup */
mask = INTR_MASK;
if (!hcd->self.root_hub->do_remote_wakeup)
mask &= ~STS_PCD;
ehci_writel(ehci, mask, &ehci->regs->intr_enable);
ehci_readl(ehci, &ehci->regs->intr_enable);
done:
ehci->next_statechange = jiffies + msecs_to_jiffies(10);
ehci->enabled_hrtimer_events = 0;
ehci->next_hrtimer_event = EHCI_HRTIMER_NO_EVENT;
spin_unlock_irq (&ehci->lock);
hrtimer_cancel(&ehci->hrtimer);
return 0;
}
/* caller has locked the root hub, and should reset/reinit on error */
static int ehci_bus_resume (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp;
u32 power_okay;
int i;
unsigned long resume_needed = 0;
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
spin_lock_irq (&ehci->lock);
if (!HCD_HW_ACCESSIBLE(hcd) || ehci->shutdown)
goto shutdown;
if (unlikely(ehci->debug)) {
if (!dbgp_reset_prep(hcd))
ehci->debug = NULL;
else
dbgp_external_startup(hcd);
}
/* Ideally and we've got a real resume here, and no port's power
* was lost. (For PCI, that means Vaux was maintained.) But we
* could instead be restoring a swsusp snapshot -- so that BIOS was
* the last user of the controller, not reset/pm hardware keeping
* state we gave to it.
*/
power_okay = ehci_readl(ehci, &ehci->regs->intr_enable);
ehci_dbg(ehci, "resume root hub%s\n",
power_okay ? "" : " after power loss");
/* at least some APM implementations will try to deliver
* IRQs right away, so delay them until we're ready.
*/
ehci_writel(ehci, 0, &ehci->regs->intr_enable);
/* re-init operational registers */
ehci_writel(ehci, 0, &ehci->regs->segment);
ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
ehci_writel(ehci, (u32) ehci->async->qh_dma, &ehci->regs->async_next);
/* restore CMD_RUN, framelist size, and irq threshold */
ehci->command |= CMD_RUN;
ehci_writel(ehci, ehci->command, &ehci->regs->command);
ehci->rh_state = EHCI_RH_RUNNING;
/*
* According to Bugzilla #8190, the port status for some controllers
* will be wrong without a delay. At their wrong status, the port
* is enabled, but not suspended neither resumed.
*/
i = HCS_N_PORTS(ehci->hcs_params);
while (i--) {
temp = ehci_readl(ehci, &ehci->regs->port_status[i]);
if ((temp & PORT_PE) &&
!(temp & (PORT_SUSPEND | PORT_RESUME))) {
ehci_dbg(ehci, "Port status(0x%x) is wrong\n", temp);
spin_unlock_irq(&ehci->lock);
msleep(8);
spin_lock_irq(&ehci->lock);
break;
}
}
if (ehci->shutdown)
goto shutdown;
/* clear phy low-power mode before resume */
if (ehci->bus_suspended && ehci->has_tdi_phy_lpm) {
i = HCS_N_PORTS(ehci->hcs_params);
while (i--) {
if (test_bit(i, &ehci->bus_suspended)) {
u32 __iomem *hostpc_reg =
&ehci->regs->hostpc[i];
temp = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp & ~HOSTPC_PHCD,
hostpc_reg);
}
}
spin_unlock_irq(&ehci->lock);
msleep(5);
spin_lock_irq(&ehci->lock);
if (ehci->shutdown)
goto shutdown;
}
/* manually resume the ports we suspended during bus_suspend() */
i = HCS_N_PORTS (ehci->hcs_params);
while (i--) {
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
if (test_bit(i, &ehci->bus_suspended) &&
(temp & PORT_SUSPEND)) {
temp |= PORT_RESUME;
set_bit(i, &resume_needed);
}
ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
}
/*
* msleep for USB_RESUME_TIMEOUT ms only if code is trying to resume
* port
*/
if (resume_needed) {
spin_unlock_irq(&ehci->lock);
msleep(USB_RESUME_TIMEOUT);
spin_lock_irq(&ehci->lock);
if (ehci->shutdown)
goto shutdown;
}
i = HCS_N_PORTS (ehci->hcs_params);
while (i--) {
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
if (test_bit(i, &resume_needed)) {
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
}
}
ehci->next_statechange = jiffies + msecs_to_jiffies(5);
spin_unlock_irq(&ehci->lock);
ehci_handover_companion_ports(ehci);
/* Now we can safely re-enable irqs */
spin_lock_irq(&ehci->lock);
if (ehci->shutdown)
goto shutdown;
ehci_writel(ehci, INTR_MASK, &ehci->regs->intr_enable);
(void) ehci_readl(ehci, &ehci->regs->intr_enable);
spin_unlock_irq(&ehci->lock);
return 0;
shutdown:
spin_unlock_irq(&ehci->lock);
return -ESHUTDOWN;
}
static unsigned long ehci_get_resuming_ports(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
return ehci->resuming_ports;
}
#else
#define ehci_bus_suspend NULL
#define ehci_bus_resume NULL
#define ehci_get_resuming_ports NULL
#endif /* CONFIG_PM */
/*-------------------------------------------------------------------------*/
/*
* Sets the owner of a port
*/
static void set_owner(struct ehci_hcd *ehci, int portnum, int new_owner)
{
u32 __iomem *status_reg;
u32 port_status;
int try;
status_reg = &ehci->regs->port_status[portnum];
/*
* The controller won't set the OWNER bit if the port is
* enabled, so this loop will sometimes require at least two
* iterations: one to disable the port and one to set OWNER.
*/
for (try = 4; try > 0; --try) {
spin_lock_irq(&ehci->lock);
port_status = ehci_readl(ehci, status_reg);
if ((port_status & PORT_OWNER) == new_owner
|| (port_status & (PORT_OWNER | PORT_CONNECT))
== 0)
try = 0;
else {
port_status ^= PORT_OWNER;
port_status &= ~(PORT_PE | PORT_RWC_BITS);
ehci_writel(ehci, port_status, status_reg);
}
spin_unlock_irq(&ehci->lock);
if (try > 1)
msleep(5);
}
}
/*-------------------------------------------------------------------------*/
static int check_reset_complete (
struct ehci_hcd *ehci,
int index,
u32 __iomem *status_reg,
int port_status
) {
if (!(port_status & PORT_CONNECT))
return port_status;
/* if reset finished and it's still not enabled -- handoff */
if (!(port_status & PORT_PE)) {
/* with integrated TT, there's nobody to hand it to! */
if (ehci_is_TDI(ehci)) {
ehci_dbg (ehci,
"Failed to enable port %d on root hub TT\n",
index+1);
return port_status;
}
ehci_dbg (ehci, "port %d full speed --> companion\n",
index + 1);
// what happens if HCS_N_CC(params) == 0 ?
port_status |= PORT_OWNER;
port_status &= ~PORT_RWC_BITS;
ehci_writel(ehci, port_status, status_reg);
/* ensure 440EPX ohci controller state is operational */
if (ehci->has_amcc_usb23)
set_ohci_hcfs(ehci, 1);
} else {
ehci_dbg(ehci, "port %d reset complete, port enabled\n",
index + 1);
/* ensure 440EPx ohci controller state is suspended */
if (ehci->has_amcc_usb23)
set_ohci_hcfs(ehci, 0);
}
return port_status;
}
/*-------------------------------------------------------------------------*/
/* build "status change" packet (one or two bytes) from HC registers */
static int
ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp, status;
u32 mask;
int ports, i, retval = 1;
unsigned long flags;
u32 ppcd = ~0;
/* init status to no-changes */
buf [0] = 0;
ports = HCS_N_PORTS (ehci->hcs_params);
if (ports > 7) {
buf [1] = 0;
retval++;
}
/* Inform the core about resumes-in-progress by returning
* a non-zero value even if there are no status changes.
*/
status = ehci->resuming_ports;
/* Some boards (mostly VIA?) report bogus overcurrent indications,
* causing massive log spam unless we completely ignore them. It
* may be relevant that VIA VT8235 controllers, where PORT_POWER is
* always set, seem to clear PORT_OCC and PORT_CSC when writing to
* PORT_POWER; that's surprising, but maybe within-spec.
*/
if (!ignore_oc && !ehci->spurious_oc)
mask = PORT_CSC | PORT_PEC | PORT_OCC;
else
mask = PORT_CSC | PORT_PEC;
// PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND
/* no hub change reports (bit 0) for now (power, ...) */
/* port N changes (bit N)? */
spin_lock_irqsave (&ehci->lock, flags);
/* get per-port change detect bits */
if (ehci->has_ppcd)
ppcd = ehci_readl(ehci, &ehci->regs->status) >> 16;
for (i = 0; i < ports; i++) {
/* leverage per-port change bits feature */
if (ppcd & (1 << i))
temp = ehci_readl(ehci, &ehci->regs->port_status[i]);
else
temp = 0;
/*
* Return status information even for ports with OWNER set.
* Otherwise hub_wq wouldn't see the disconnect event when a
* high-speed device is switched over to the companion
* controller by the user.
*/
if ((temp & mask) != 0 || test_bit(i, &ehci->port_c_suspend)
|| (ehci->reset_done[i] && time_after_eq(
jiffies, ehci->reset_done[i]))
|| ehci_has_ci_pec_bug(ehci, temp)) {
if (i < 7)
buf [0] |= 1 << (i + 1);
else
buf [1] |= 1 << (i - 7);
status = STS_PCD;
}
}
/* If a resume is in progress, make sure it can finish */
if (ehci->resuming_ports)
mod_timer(&hcd->rh_timer, jiffies + msecs_to_jiffies(25));
spin_unlock_irqrestore (&ehci->lock, flags);
return status ? retval : 0;
}
/*-------------------------------------------------------------------------*/
static void
ehci_hub_descriptor (
struct ehci_hcd *ehci,
struct usb_hub_descriptor *desc
) {
int ports = HCS_N_PORTS (ehci->hcs_params);
u16 temp;
desc->bDescriptorType = USB_DT_HUB;
desc->bPwrOn2PwrGood = 10; /* ehci 1.0, 2.3.9 says 20ms max */
desc->bHubContrCurrent = 0;
desc->bNbrPorts = ports;
temp = 1 + (ports / 8);
desc->bDescLength = 7 + 2 * temp;
/* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */
memset(&desc->u.hs.DeviceRemovable[0], 0, temp);
memset(&desc->u.hs.DeviceRemovable[temp], 0xff, temp);
temp = HUB_CHAR_INDV_PORT_OCPM; /* per-port overcurrent reporting */
if (HCS_PPC (ehci->hcs_params))
temp |= HUB_CHAR_INDV_PORT_LPSM; /* per-port power control */
else
temp |= HUB_CHAR_NO_LPSM; /* no power switching */
#if 0
// re-enable when we support USB_PORT_FEAT_INDICATOR below.
if (HCS_INDICATOR (ehci->hcs_params))
temp |= HUB_CHAR_PORTIND; /* per-port indicators (LEDs) */
#endif
desc->wHubCharacteristics = cpu_to_le16(temp);
}
/*-------------------------------------------------------------------------*/
int ehci_hub_control(
struct usb_hcd *hcd,
u16 typeReq,
u16 wValue,
u16 wIndex,
char *buf,
u16 wLength
) {
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int ports = HCS_N_PORTS (ehci->hcs_params);
u32 __iomem *status_reg, *hostpc_reg;
u32 temp, temp1, status;
unsigned long flags;
int retval = 0;
unsigned selector;
/*
* Avoid out-of-bounds values while calculating the port index
* from wIndex. The compiler doesn't like pointers to invalid
* addresses, even if they are never used.
*/
temp = (wIndex - 1) & 0xff;
if (temp >= HCS_N_PORTS_MAX)
temp = 0;
status_reg = &ehci->regs->port_status[temp];
hostpc_reg = &ehci->regs->hostpc[temp];
/*
* FIXME: support SetPortFeatures USB_PORT_FEAT_INDICATOR.
* HCS_INDICATOR may say we can change LEDs to off/amber/green.
* (track current state ourselves) ... blink for diagnostics,
* power, "this is the one", etc. EHCI spec supports this.
*/
spin_lock_irqsave (&ehci->lock, flags);
switch (typeReq) {
case ClearHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case ClearPortFeature:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = ehci_readl(ehci, status_reg);
temp &= ~PORT_RWC_BITS;
/*
* Even if OWNER is set, so the port is owned by the
* companion controller, hub_wq needs to be able to clear
* the port-change status bits (especially
* USB_PORT_STAT_C_CONNECTION).
*/
switch (wValue) {
case USB_PORT_FEAT_ENABLE:
ehci_writel(ehci, temp & ~PORT_PE, status_reg);
break;
case USB_PORT_FEAT_C_ENABLE:
ehci_writel(ehci, temp | PORT_PEC, status_reg);
break;
case USB_PORT_FEAT_SUSPEND:
if (temp & PORT_RESET)
goto error;
if (ehci->no_selective_suspend)
break;
#ifdef CONFIG_USB_OTG
if ((hcd->self.otg_port == (wIndex + 1))
&& hcd->self.b_hnp_enable) {
otg_start_hnp(hcd->usb_phy->otg);
break;
}
#endif
if (!(temp & PORT_SUSPEND))
break;
if ((temp & PORT_PE) == 0)
goto error;
/* clear phy low-power mode before resume */
if (ehci->has_tdi_phy_lpm) {
temp1 = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp1 & ~HOSTPC_PHCD,
hostpc_reg);
spin_unlock_irqrestore(&ehci->lock, flags);
msleep(5);/* wait to leave low-power mode */
spin_lock_irqsave(&ehci->lock, flags);
}
/* resume signaling for 20 msec */
temp &= ~PORT_WAKE_BITS;
ehci_writel(ehci, temp | PORT_RESUME, status_reg);
ehci->reset_done[wIndex] = jiffies
+ msecs_to_jiffies(USB_RESUME_TIMEOUT);
set_bit(wIndex, &ehci->resuming_ports);
usb_hcd_start_port_resume(&hcd->self, wIndex);
break;
case USB_PORT_FEAT_C_SUSPEND:
clear_bit(wIndex, &ehci->port_c_suspend);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC(ehci->hcs_params)) {
spin_unlock_irqrestore(&ehci->lock, flags);
ehci_port_power(ehci, wIndex, false);
spin_lock_irqsave(&ehci->lock, flags);
}
break;
case USB_PORT_FEAT_C_CONNECTION:
ehci_writel(ehci, temp | PORT_CSC, status_reg);
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
ehci_writel(ehci, temp | PORT_OCC, status_reg);
break;
case USB_PORT_FEAT_C_RESET:
/* GetPortStatus clears reset */
break;
default:
goto error;
}
ehci_readl(ehci, &ehci->regs->command); /* unblock posted write */
break;
case GetHubDescriptor:
ehci_hub_descriptor (ehci, (struct usb_hub_descriptor *)
buf);
break;
case GetHubStatus:
/* no hub-wide feature/status flags */
memset (buf, 0, 4);
//cpu_to_le32s ((u32 *) buf);
break;
case GetPortStatus:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
status = 0;
temp = ehci_readl(ehci, status_reg);
// wPortChange bits
if (temp & PORT_CSC)
status |= USB_PORT_STAT_C_CONNECTION << 16;
if (temp & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
if (ehci_has_ci_pec_bug(ehci, temp)) {
status |= USB_PORT_STAT_C_ENABLE << 16;
ehci_info(ehci,
"PE is cleared by HW port:%d PORTSC:%08x\n",
wIndex + 1, temp);
}
if ((temp & PORT_OCC) && (!ignore_oc && !ehci->spurious_oc)){
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
/*
* Hubs should disable port power on over-current.
* However, not all EHCI implementations do this
* automatically, even if they _do_ support per-port
* power switching; they're allowed to just limit the
* current. hub_wq will turn the power back on.
*/
if (((temp & PORT_OC) || (ehci->need_oc_pp_cycle))
&& HCS_PPC(ehci->hcs_params)) {
spin_unlock_irqrestore(&ehci->lock, flags);
ehci_port_power(ehci, wIndex, false);
spin_lock_irqsave(&ehci->lock, flags);
temp = ehci_readl(ehci, status_reg);
}
}
/* no reset or resume pending */
if (!ehci->reset_done[wIndex]) {
/* Remote Wakeup received? */
if (temp & PORT_RESUME) {
/* resume signaling for 20 msec */
ehci->reset_done[wIndex] = jiffies
+ msecs_to_jiffies(20);
usb_hcd_start_port_resume(&hcd->self, wIndex);
set_bit(wIndex, &ehci->resuming_ports);
/* check the port again */
mod_timer(&ehci_to_hcd(ehci)->rh_timer,
ehci->reset_done[wIndex]);
}
/* reset or resume not yet complete */
} else if (!time_after_eq(jiffies, ehci->reset_done[wIndex])) {
; /* wait until it is complete */
/* resume completed */
} else if (test_bit(wIndex, &ehci->resuming_ports)) {
clear_bit(wIndex, &ehci->suspended_ports);
set_bit(wIndex, &ehci->port_c_suspend);
ehci->reset_done[wIndex] = 0;
usb_hcd_end_port_resume(&hcd->self, wIndex);
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
if (retval != 0) {
ehci_err(ehci, "port %d resume error %d\n",
wIndex + 1, retval);
goto error;
}
temp = ehci_readl(ehci, status_reg);
/* whoever resets must GetPortStatus to complete it!! */
} else {
status |= USB_PORT_STAT_C_RESET << 16;
ehci->reset_done [wIndex] = 0;
/* force reset to complete */
ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESET),
status_reg);
/* REVISIT: some hardware needs 550+ usec to clear
* this bit; seems too long to spin routinely...
*/
retval = ehci_handshake(ehci, status_reg,
PORT_RESET, 0, 1000);
if (retval != 0) {
ehci_err (ehci, "port %d reset error %d\n",
wIndex + 1, retval);
goto error;
}
/* see what we found out */
temp = check_reset_complete (ehci, wIndex, status_reg,
ehci_readl(ehci, status_reg));
}
/* transfer dedicated ports to the companion hc */
if ((temp & PORT_CONNECT) &&
test_bit(wIndex, &ehci->companion_ports)) {
temp &= ~PORT_RWC_BITS;
temp |= PORT_OWNER;
ehci_writel(ehci, temp, status_reg);
ehci_dbg(ehci, "port %d --> companion\n", wIndex + 1);
temp = ehci_readl(ehci, status_reg);
}
/*
* Even if OWNER is set, there's no harm letting hub_wq
* see the wPortStatus values (they should all be 0 except
* for PORT_POWER anyway).
*/
if (temp & PORT_CONNECT) {
status |= USB_PORT_STAT_CONNECTION;
// status may be from integrated TT
if (ehci->has_hostpc) {
temp1 = ehci_readl(ehci, hostpc_reg);
status |= ehci_port_speed(ehci, temp1);
} else
status |= ehci_port_speed(ehci, temp);
}
if (temp & PORT_PE)
status |= USB_PORT_STAT_ENABLE;
/* maybe the port was unsuspended without our knowledge */
if (temp & (PORT_SUSPEND|PORT_RESUME)) {
status |= USB_PORT_STAT_SUSPEND;
} else if (test_bit(wIndex, &ehci->suspended_ports)) {
clear_bit(wIndex, &ehci->suspended_ports);
clear_bit(wIndex, &ehci->resuming_ports);
ehci->reset_done[wIndex] = 0;
if (temp & PORT_PE)
set_bit(wIndex, &ehci->port_c_suspend);
usb_hcd_end_port_resume(&hcd->self, wIndex);
}
if (temp & PORT_OC)
status |= USB_PORT_STAT_OVERCURRENT;
if (temp & PORT_RESET)
status |= USB_PORT_STAT_RESET;
if (temp & PORT_POWER)
status |= USB_PORT_STAT_POWER;
if (test_bit(wIndex, &ehci->port_c_suspend))
status |= USB_PORT_STAT_C_SUSPEND << 16;
if (status & ~0xffff) /* only if wPortChange is interesting */
dbg_port(ehci, "GetStatus", wIndex + 1, temp);
put_unaligned_le32(status, buf);
break;
case SetHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case SetPortFeature:
selector = wIndex >> 8;
wIndex &= 0xff;
if (unlikely(ehci->debug)) {
/* If the debug port is active any port
* feature requests should get denied */
if (wIndex == HCS_DEBUG_PORT(ehci->hcs_params) &&
(readl(&ehci->debug->control) & DBGP_ENABLED)) {
retval = -ENODEV;
goto error_exit;
}
}
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = ehci_readl(ehci, status_reg);
if (temp & PORT_OWNER)
break;
temp &= ~PORT_RWC_BITS;
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
if (ehci->no_selective_suspend)
break;
if ((temp & PORT_PE) == 0
|| (temp & PORT_RESET) != 0)
goto error;
/* After above check the port must be connected.
* Set appropriate bit thus could put phy into low power
* mode if we have tdi_phy_lpm feature
*/
temp &= ~PORT_WKCONN_E;
temp |= PORT_WKDISC_E | PORT_WKOC_E;
ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
if (ehci->has_tdi_phy_lpm) {
spin_unlock_irqrestore(&ehci->lock, flags);
msleep(5);/* 5ms for HCD enter low pwr mode */
spin_lock_irqsave(&ehci->lock, flags);
temp1 = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp1 | HOSTPC_PHCD,
hostpc_reg);
temp1 = ehci_readl(ehci, hostpc_reg);
ehci_dbg(ehci, "Port%d phy low pwr mode %s\n",
wIndex, (temp1 & HOSTPC_PHCD) ?
"succeeded" : "failed");
}
if (ehci_has_fsl_susp_errata(ehci)) {
/* 10ms for HCD enter suspend */
spin_unlock_irqrestore(&ehci->lock, flags);
usleep_range(10000, 20000);
spin_lock_irqsave(&ehci->lock, flags);
}
set_bit(wIndex, &ehci->suspended_ports);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC(ehci->hcs_params)) {
spin_unlock_irqrestore(&ehci->lock, flags);
ehci_port_power(ehci, wIndex, true);
spin_lock_irqsave(&ehci->lock, flags);
}
break;
case USB_PORT_FEAT_RESET:
if (temp & (PORT_SUSPEND|PORT_RESUME))
goto error;
/* line status bits may report this as low speed,
* which can be fine if this root hub has a
* transaction translator built in.
*/
if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
&& !ehci_is_TDI(ehci)
&& PORT_USB11 (temp)) {
ehci_dbg (ehci,
"port %d low speed --> companion\n",
wIndex + 1);
temp |= PORT_OWNER;
} else {
temp |= PORT_RESET;
temp &= ~PORT_PE;
/*
* caller must wait, then call GetPortStatus
* usb 2.0 spec says 50 ms resets on root
*/
ehci->reset_done [wIndex] = jiffies
+ msecs_to_jiffies (50);
/*
* Force full-speed connect for FSL high-speed
* erratum; disable HS Chirp by setting PFSC bit
*/
if (ehci_has_fsl_hs_errata(ehci))
temp |= (1 << PORTSC_FSL_PFSC);
}
ehci_writel(ehci, temp, status_reg);
break;
/* For downstream facing ports (these): one hub port is put
* into test mode according to USB2 11.24.2.13, then the hub
* must be reset (which for root hub now means rmmod+modprobe,
* or else system reboot). See EHCI 2.3.9 and 4.14 for info
* about the EHCI-specific stuff.
*/
case USB_PORT_FEAT_TEST:
#ifdef CONFIG_USB_HCD_TEST_MODE
if (selector == EHSET_TEST_SINGLE_STEP_SET_FEATURE) {
spin_unlock_irqrestore(&ehci->lock, flags);
retval = ehset_single_step_set_feature(hcd,
wIndex + 1);
spin_lock_irqsave(&ehci->lock, flags);
break;
}
#endif
if (!selector || selector > 5)
goto error;
spin_unlock_irqrestore(&ehci->lock, flags);
ehci_quiesce(ehci);
spin_lock_irqsave(&ehci->lock, flags);
/* Put all enabled ports into suspend */
while (ports--) {
u32 __iomem *sreg =
&ehci->regs->port_status[ports];
temp = ehci_readl(ehci, sreg) & ~PORT_RWC_BITS;
if (temp & PORT_PE)
ehci_writel(ehci, temp | PORT_SUSPEND,
sreg);
}
spin_unlock_irqrestore(&ehci->lock, flags);
ehci_halt(ehci);
spin_lock_irqsave(&ehci->lock, flags);
temp = ehci_readl(ehci, status_reg);
temp |= selector << 16;
ehci_writel(ehci, temp, status_reg);
break;
default:
goto error;
}
ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
error_exit:
spin_unlock_irqrestore (&ehci->lock, flags);
return retval;
}
EXPORT_SYMBOL_GPL(ehci_hub_control);
static void ehci_relinquish_port(struct usb_hcd *hcd, int portnum)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
if (ehci_is_TDI(ehci))
return;
set_owner(ehci, --portnum, PORT_OWNER);
}
static int ehci_port_handed_over(struct usb_hcd *hcd, int portnum)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
u32 __iomem *reg;
if (ehci_is_TDI(ehci))
return 0;
reg = &ehci->regs->port_status[portnum - 1];
return ehci_readl(ehci, reg) & PORT_OWNER;
}
static int ehci_port_power(struct ehci_hcd *ehci, int portnum, bool enable)
{
struct usb_hcd *hcd = ehci_to_hcd(ehci);
u32 __iomem *status_reg = &ehci->regs->port_status[portnum];
u32 temp = ehci_readl(ehci, status_reg) & ~PORT_RWC_BITS;
if (enable)
ehci_writel(ehci, temp | PORT_POWER, status_reg);
else
ehci_writel(ehci, temp & ~PORT_POWER, status_reg);
if (hcd->driver->port_power)
hcd->driver->port_power(hcd, portnum, enable);
return 0;
}
Reference in New Issue View Git Blame Copy Permalink